[U-Boot] [PATCH] usb: tegra: Fix PHY configuration for Tegra 3

Jim Lin jilin at nvidia.com
Fri Feb 14 11:59:58 CET 2014


On Fri, 2014-02-14 at 03:21 +0800, Stefan Agner wrote:
> On Tegra 3, the PTS (parallel transceiver select) and STS (serial
> transceiver select) are part of the HOSTPC1_DEVLC_0 register rather
> than PORTSC1_0 register. Since the reset configuration usually
> matches the configured registers, this error did not show up on
> Tegra 3 devices.
> 
> Also clear the forced powerdown bit in the UTMIP_PLL_CFG2_0 register
> which brings USB2 in UTMI mode to work. This was clearly missing
> since the forced powerdown bit is set in reset by default for all
> USB ports.
> 
> Signed-off-by: Stefan Agner <stefan at agner.ch>
> ---
>  drivers/usb/host/ehci-tegra.c | 22 ++++++++++++++++++----
>  1 file changed, 18 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/usb/host/ehci-tegra.c b/drivers/usb/host/ehci-tegra.c
> index 0b42aa5..fdd56c9 100644
> --- a/drivers/usb/host/ehci-tegra.c
> +++ b/drivers/usb/host/ehci-tegra.c
> @@ -461,6 +461,9 @@ static int init_utmi_usb_controller(struct fdt_usb *config)
>  		if (config->periph_id == PERIPH_ID_USBD)
>  			clrbits_le32(&clkrst->crc_utmip_pll_cfg2,
>  				     UTMIP_FORCE_PD_SAMP_A_POWERDOWN);
> +		if (config->periph_id == PERIPH_ID_USB2)
> +			clrbits_le32(&clkrst->crc_utmip_pll_cfg2,
> +				     UTMIP_FORCE_PD_SAMP_B_POWERDOWN);
>  		if (config->periph_id == PERIPH_ID_USB3)
>  			clrbits_le32(&clkrst->crc_utmip_pll_cfg2,
>  				     UTMIP_FORCE_PD_SAMP_C_POWERDOWN);
> @@ -483,9 +486,15 @@ static int init_utmi_usb_controller(struct fdt_usb *config)
>  	clrbits_le32(&usbctlr->icusb_ctrl, IC_ENB1);
>  
>  	/* Select UTMI parallel interface */
> -	clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK,
> -			PTS_UTMI << PTS_SHIFT);
> -	clrbits_le32(&usbctlr->port_sc1, STS);
> +	if (!controller->has_hostpc) {
> +		clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK,
> +				PTS_UTMI << PTS_SHIFT);
> +		clrbits_le32(&usbctlr->port_sc1, STS);
> +	} else {
> +		clrsetbits_le32(&usbctlr->hostpc1_devlc, PTS_MASK,
> +				PTS_UTMI << PTS_SHIFT);
> +		clrbits_le32(&usbctlr->hostpc1_devlc, STS);
> +	}

Could you help to change above code like this?
Thanks.

+	if (!controller->has_hostpc) {
+		if (config->periph_id == PERIPH_ID_USBD) {
+			clrsetbits_le32(&usbctlr->port_sc1, PTS1_MASK,
+				PTS_UTMI << PTS1_SHIFT);
+			clrbits_le32(&usbctlr->port_sc1, STS1);
+		} else {
+			clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK,
+				PTS_UTMI << PTS_SHIFT);
+			clrbits_le32(&usbctlr->port_sc1, STS);
+		}
+	} else {
+		clrsetbits_le32(&usbctlr->hostpc1_devlc, PTS_MASK,
+				PTS_UTMI << PTS_SHIFT);
+		clrbits_le32(&usbctlr->hostpc1_devlc, STS);
+	}

Others look good.

--nvpublic



More information about the U-Boot mailing list