[U-Boot] [PULL] : Please pull u-boot-imx

Stefano Babic sbabic at denx.de
Wed Feb 19 11:04:53 CET 2014


Hi Albert,

please pull from u-boot-imx, thanks !


The following changes since commit e97f9d817e600cd6f43d1d0da76f5787e33a5c56:

  Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' (2014-01-29
14:07:50 +0100)

are available in the git repository at:


  git://www.denx.de/git/u-boot-imx.git master

for you to fetch changes up to da781c60e5d55904d77931fcb63f25e65e2228be:

  imx6 SION bit has to be on for the pins that are used as ENET_REF_CLK
(2014-02-19 10:57:25 +0100)

----------------------------------------------------------------
Andy Ng (1):
      imx6 SION bit has to be on for the pins that are used as ENET_REF_CLK

Anson Huang (2):
      imx6: ensure AHB clock is 132MHz in low freq boot mode
      imx6: make sure MMDC_CHx_MASK is clear to avoid warm reset failure

Eric Nelson (1):
      i.MX6: nitrogen6x: pedantic: BOOT_FROM==spi, not sd

Fabio Estevam (8):
      nitrogen6x: README: Only calling 'make' is enough
      nitrogen6x: README: Do not refer to MAINTAINERS file
      mx6sl: Adjust fdt_addr to avoid address overlapping
      hummingboard: Return from cpu_eth_init() directly
      imx: Introduce a header for the imx cpu versions
      mx6: Distinguish mx6dual from mx6quad
      mx6qsabreauto: Update imximage.cfg
      mx6: Enable L2 cache support

Marek Vasut (7):
      ARM: armv7: Make indirect vector addresses globl
      ARM: mx6: Add PCI express clock configuration
      ARM: mx6: Add PCI express driver
      ARM: mx6: Enable PCIe on Sabrelite
      ARM: m53evk: Rename mxc-nand to mxc_nand
      ARM: m53evk: Enable CONFIG_REGEX
      pci: mx6: Implement reset callback

Markus Niebel (2):
      ARM: imx6: fix wrong fec clk
      NET: fec_mxc: fix MDIO clock prescaler calculation

Otavio Salvador (11):
      cgtqmx6eval: Set default environment to use zImage
      hummingboard: Set default environment to use zImage
      mx23evk: Set default environment to use zImage
      mx28evk: Set default environment to use zImage
      mx51evk: Set default environment to use zImage
      mx53loco: Set default environment to use zImage
      mx6qarm2: Set default environment to use zImage
      mx6sabre_common: Set default environment to use zImage
      mx6slevk: Set default environment to use zImage
      udoo: Set default environment to use zImage
      vf610twr: Set default environment to use zImage

Stefano Babic (2):
      Merge branch 'master' of git://git.denx.de/u-boot-arm
      Merge branch 'master' of git://git.denx.de/u-boot-arm

 arch/arm/cpu/armv7/mx6/clock.c              |   77 +++-
 arch/arm/cpu/armv7/mx6/soc.c                |  103 ++++-
 arch/arm/cpu/armv7/start.S                  |    7 +
 arch/arm/imx-common/cpu.c                   |    2 +
 arch/arm/include/asm/arch-imx/cpu.h         |   13 +
 arch/arm/include/asm/arch-mx5/sys_proto.h   |    7 +-
 arch/arm/include/asm/arch-mx6/clock.h       |    1 +
 arch/arm/include/asm/arch-mx6/imx-regs.h    |    1 +
 arch/arm/include/asm/arch-mx6/iomux.h       |   27 ++
 arch/arm/include/asm/arch-mx6/mx6dl_pins.h  |    6 +-
 arch/arm/include/asm/arch-mx6/mx6q_pins.h   |    6 +-
 arch/arm/include/asm/arch-mx6/sys_proto.h   |    8 +-
 arch/arm/include/asm/pl310.h                |   21 +
 board/boundary/nitrogen6x/README            |    4 +-
 board/boundary/nitrogen6x/nitrogen6dl.cfg   |    2 +-
 board/boundary/nitrogen6x/nitrogen6dl2g.cfg |    2 +-
 board/boundary/nitrogen6x/nitrogen6q.cfg    |    2 +-
 board/boundary/nitrogen6x/nitrogen6q2g.cfg  |    2 +-
 board/boundary/nitrogen6x/nitrogen6s.cfg    |    2 +-
 board/boundary/nitrogen6x/nitrogen6s1g.cfg  |    2 +-
 board/freescale/mx6qsabreauto/imximage.cfg  |  136 +++---
 board/solidrun/hummingboard/hummingboard.c  |    6 +-
 drivers/net/fec_mxc.c                       |    8 +-
 drivers/pci/Makefile                        |    1 +
 drivers/pci/pcie_imx.c                      |  606
+++++++++++++++++++++++++++
 include/configs/cgtqmx6eval.h               |   14 +-
 include/configs/hummingboard.h              |   20 +-
 include/configs/m53evk.h                    |    6 +-
 include/configs/mx23evk.h                   |   12 +-
 include/configs/mx28evk.h                   |   26 +-
 include/configs/mx51evk.h                   |   20 +-
 include/configs/mx53loco.h                  |   20 +-
 include/configs/mx6_common.h                |    5 +
 include/configs/mx6qarm2.h                  |   10 +-
 include/configs/mx6sabre_common.h           |   20 +-
 include/configs/mx6slevk.h                  |   22 +-
 include/configs/nitrogen6x.h                |   11 +
 include/configs/udoo.h                      |   20 +-
 include/configs/vf610twr.h                  |   20 +-
 39 files changed, 1049 insertions(+), 229 deletions(-)
 create mode 100644 arch/arm/include/asm/arch-imx/cpu.h
 create mode 100644 drivers/pci/pcie_imx.c



-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================


More information about the U-Boot mailing list