[U-Boot] [PATCH v2] powerpc/t2081qds: Add T2081 QDS board support
Shengzhou Liu
Shengzhou.Liu at freescale.com
Thu Feb 20 07:25:38 CET 2014
T2081 QDS is a high-performance computing evaluation, development and
test platform supporting the T2081 QorIQ Power Architecture processor.
T2081QDS board Overview
-----------------------
- T2081 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
- 2MB shared L2 and 512KB L3 CoreNet platform cache (CPC)
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3/DDR3LP SDRAM memory controller with ECC and interleaving
- Ethernet interfaces:
- Two on-board 10M/100M/1G bps RGMII ports
- Two 10Gbps XFI with on-board SFP+ cage
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
- Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
- SerDes:
- 8 lanes up to 10.3125GHz
- Supports SGMII, HiGig, XFI, XAUI and Aurora debug,
- IFC:
- 512MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- eSPI:
- Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
- USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- PCIe:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
- eSDHC:
- Supports various SD/SDHC/SDXC/eMMC devices with adapter cards and
voltage translators
- I2C:
- Four I2C controllers.
- UART:
- Dual 4-pins UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu at freescale.com>
---
v2: some update for serdes and network configuration.
board/freescale/{t2080qds => t208xqds}/Makefile | 6 +-
board/freescale/{t2080qds => t208xqds}/ddr.c | 0
board/freescale/{t2080qds => t208xqds}/ddr.h | 0
.../eth_t2080qds.c => t208xqds/eth_t208xqds.c} | 188 ++++++++++++++++-----
board/freescale/{t2080qds => t208xqds}/law.c | 0
board/freescale/{t2080qds => t208xqds}/pci.c | 0
.../freescale/{t2080qds => t208xqds}/t2080_rcw.cfg | 0
board/freescale/t208xqds/t2081_rcw.cfg | 8 +
.../t2080_pbi.cfg => t208xqds/t208x_pbi.cfg} | 0
.../{t2080qds/t2080qds.c => t208xqds/t208xqds.c} | 89 +++++++++-
.../{t2080qds/t2080qds.h => t208xqds/t208xqds.h} | 0
.../t2080qds_qixis.h => t208xqds/t208xqds_qixis.h} | 8 +-
board/freescale/{t2080qds => t208xqds}/tlb.c | 0
boards.cfg | 15 +-
include/configs/{T2080QDS.h => T208xQDS.h} | 29 +++-
15 files changed, 277 insertions(+), 66 deletions(-)
rename board/freescale/{t2080qds => t208xqds}/Makefile (53%)
rename board/freescale/{t2080qds => t208xqds}/ddr.c (100%)
rename board/freescale/{t2080qds => t208xqds}/ddr.h (100%)
rename board/freescale/{t2080qds/eth_t2080qds.c => t208xqds/eth_t208xqds.c} (70%)
rename board/freescale/{t2080qds => t208xqds}/law.c (100%)
rename board/freescale/{t2080qds => t208xqds}/pci.c (100%)
rename board/freescale/{t2080qds => t208xqds}/t2080_rcw.cfg (100%)
create mode 100644 board/freescale/t208xqds/t2081_rcw.cfg
rename board/freescale/{t2080qds/t2080_pbi.cfg => t208xqds/t208x_pbi.cfg} (100%)
rename board/freescale/{t2080qds/t2080qds.c => t208xqds/t208xqds.c} (80%)
rename board/freescale/{t2080qds/t2080qds.h => t208xqds/t208xqds.h} (100%)
rename board/freescale/{t2080qds/t2080qds_qixis.h => t208xqds/t208xqds_qixis.h} (90%)
rename board/freescale/{t2080qds => t208xqds}/tlb.c (100%)
rename include/configs/{T2080QDS.h => T208xQDS.h} (97%)
diff --git a/board/freescale/t2080qds/Makefile b/board/freescale/t208xqds/Makefile
similarity index 53%
rename from board/freescale/t2080qds/Makefile
rename to board/freescale/t208xqds/Makefile
index 0b8747b..947b7f7 100644
--- a/board/freescale/t2080qds/Makefile
+++ b/board/freescale/t208xqds/Makefile
@@ -4,8 +4,10 @@
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(CONFIG_T2080QDS) += t2080qds.o
-obj-$(CONFIG_T2080QDS) += eth_t2080qds.o
+obj-$(CONFIG_T2080QDS) += t208xqds.o
+obj-$(CONFIG_T2080QDS) += eth_t208xqds.o
+obj-$(CONFIG_T2081QDS) += t208xqds.o
+obj-$(CONFIG_T2081QDS) += eth_t208xqds.o
obj-$(CONFIG_PCI) += pci.o
obj-y += ddr.o
obj-y += law.o
diff --git a/board/freescale/t2080qds/ddr.c b/board/freescale/t208xqds/ddr.c
similarity index 100%
rename from board/freescale/t2080qds/ddr.c
rename to board/freescale/t208xqds/ddr.c
diff --git a/board/freescale/t2080qds/ddr.h b/board/freescale/t208xqds/ddr.h
similarity index 100%
rename from board/freescale/t2080qds/ddr.h
rename to board/freescale/t208xqds/ddr.h
diff --git a/board/freescale/t2080qds/eth_t2080qds.c b/board/freescale/t208xqds/eth_t208xqds.c
similarity index 70%
rename from board/freescale/t2080qds/eth_t2080qds.c
rename to board/freescale/t208xqds/eth_t208xqds.c
index 3e4ab8f..8b06c2d 100644
--- a/board/freescale/t2080qds/eth_t2080qds.c
+++ b/board/freescale/t208xqds/eth_t208xqds.c
@@ -25,21 +25,30 @@
#include <asm/fsl_serdes.h>
#include "../common/qixis.h"
#include "../common/fman.h"
-#include "t2080qds_qixis.h"
+#include "t208xqds_qixis.h"
#define EMI_NONE 0xFFFFFFFF
#define EMI1_RGMII1 0
#define EMI1_RGMII2 1
#define EMI1_SLOT1 2
+#if defined(CONFIG_T2080QDS)
#define EMI1_SLOT2 6
#define EMI1_SLOT3 3
#define EMI1_SLOT4 4
#define EMI1_SLOT5 5
-#define EMI2 7
+#elif defined(CONFIG_T2081QDS)
+#define EMI1_SLOT2 3
+#define EMI1_SLOT3 4
+#define EMI1_SLOT5 5
+#define EMI1_SLOT6 6
+#define EMI1_SLOT7 7
+#endif
+#define EMI2 8
static int mdio_mux[NUM_FM_PORTS];
static const char * const mdio_names[] = {
+#if defined(CONFIG_T2080QDS)
"T2080QDS_MDIO_RGMII1",
"T2080QDS_MDIO_RGMII2",
"T2080QDS_MDIO_SLOT1",
@@ -48,12 +57,27 @@ static const char * const mdio_names[] = {
"T2080QDS_MDIO_SLOT5",
"T2080QDS_MDIO_SLOT2",
"T2080QDS_MDIO_10GC",
+#elif defined(CONFIG_T2081QDS)
+ "T2081QDS_MDIO_RGMII1",
+ "T2081QDS_MDIO_RGMII2",
+ "T2081QDS_MDIO_SLOT1",
+ "T2081QDS_MDIO_SLOT2",
+ "T2081QDS_MDIO_SLOT3",
+ "T2081QDS_MDIO_SLOT5",
+ "T2081QDS_MDIO_SLOT6",
+ "T2081QDS_MDIO_SLOT7",
+ "T2081QDS_MDIO_10GC",
+#endif
};
/* Map SerDes1 8 lanes to default slot, will be initialized dynamically */
+#if defined(CONFIG_T2080QDS)
static u8 lane_to_slot[] = {3, 3, 3, 3, 1, 1, 1, 1};
+#elif defined(CONFIG_T2081QDS)
+static u8 lane_to_slot[] = {2, 2, 2, 2, 1, 1, 1, 1};
+#endif
-static const char *T2080qds_mdio_name_for_muxval(u8 muxval)
+static const char *t208xqds_mdio_name_for_muxval(u8 muxval)
{
return mdio_names[muxval];
}
@@ -61,7 +85,7 @@ static const char *T2080qds_mdio_name_for_muxval(u8 muxval)
struct mii_dev *mii_dev_for_muxval(u8 muxval)
{
struct mii_dev *bus;
- const char *name = T2080qds_mdio_name_for_muxval(muxval);
+ const char *name = t208xqds_mdio_name_for_muxval(muxval);
if (!name) {
printf("No bus for muxval %x\n", muxval);
@@ -78,15 +102,15 @@ struct mii_dev *mii_dev_for_muxval(u8 muxval)
return bus;
}
-struct T2080qds_mdio {
+struct t208xqds_mdio {
u8 muxval;
struct mii_dev *realbus;
};
-static void T2080qds_mux_mdio(u8 muxval)
+static void t208xqds_mux_mdio(u8 muxval)
{
u8 brdcfg4;
- if (muxval < 7) {
+ if (muxval < 8) {
brdcfg4 = QIXIS_READ(brdcfg[4]);
brdcfg4 &= ~BRDCFG4_EMISEL_MASK;
brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT);
@@ -94,54 +118,54 @@ static void T2080qds_mux_mdio(u8 muxval)
}
}
-static int T2080qds_mdio_read(struct mii_dev *bus, int addr, int devad,
+static int t208xqds_mdio_read(struct mii_dev *bus, int addr, int devad,
int regnum)
{
- struct T2080qds_mdio *priv = bus->priv;
+ struct t208xqds_mdio *priv = bus->priv;
- T2080qds_mux_mdio(priv->muxval);
+ t208xqds_mux_mdio(priv->muxval);
return priv->realbus->read(priv->realbus, addr, devad, regnum);
}
-static int T2080qds_mdio_write(struct mii_dev *bus, int addr, int devad,
+static int t208xqds_mdio_write(struct mii_dev *bus, int addr, int devad,
int regnum, u16 value)
{
- struct T2080qds_mdio *priv = bus->priv;
+ struct t208xqds_mdio *priv = bus->priv;
- T2080qds_mux_mdio(priv->muxval);
+ t208xqds_mux_mdio(priv->muxval);
return priv->realbus->write(priv->realbus, addr, devad, regnum, value);
}
-static int T2080qds_mdio_reset(struct mii_dev *bus)
+static int t208xqds_mdio_reset(struct mii_dev *bus)
{
- struct T2080qds_mdio *priv = bus->priv;
+ struct t208xqds_mdio *priv = bus->priv;
return priv->realbus->reset(priv->realbus);
}
-static int T2080qds_mdio_init(char *realbusname, u8 muxval)
+static int t208xqds_mdio_init(char *realbusname, u8 muxval)
{
- struct T2080qds_mdio *pmdio;
+ struct t208xqds_mdio *pmdio;
struct mii_dev *bus = mdio_alloc();
if (!bus) {
- printf("Failed to allocate T2080QDS MDIO bus\n");
+ printf("Failed to allocate t208xqds MDIO bus\n");
return -1;
}
pmdio = malloc(sizeof(*pmdio));
if (!pmdio) {
- printf("Failed to allocate T2080QDS private data\n");
+ printf("Failed to allocate t208xqds private data\n");
free(bus);
return -1;
}
- bus->read = T2080qds_mdio_read;
- bus->write = T2080qds_mdio_write;
- bus->reset = T2080qds_mdio_reset;
- sprintf(bus->name, T2080qds_mdio_name_for_muxval(muxval));
+ bus->read = t208xqds_mdio_read;
+ bus->write = t208xqds_mdio_write;
+ bus->reset = t208xqds_mdio_reset;
+ sprintf(bus->name, t208xqds_mdio_name_for_muxval(muxval));
pmdio->realbus = miiphy_get_dev_by_name(realbusname);
@@ -154,7 +178,6 @@ static int T2080qds_mdio_init(char *realbusname, u8 muxval)
pmdio->muxval = muxval;
bus->priv = pmdio;
-
return mdio_register(bus);
}
@@ -177,9 +200,15 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
case FM1_DTSEC2:
case FM1_DTSEC9:
case FM1_DTSEC10:
- sprintf(alias, "phy_sgmii_s3_%x", phy);
- fdt_set_phy_handle(fdt, compat, addr, alias);
- fdt_status_okay_by_alias(fdt, "emi1_slot3");
+ if (mdio_mux[port] == EMI1_SLOT2) {
+ sprintf(alias, "phy_sgmii_s2_%x", phy);
+ fdt_set_phy_handle(fdt, compat, addr, alias);
+ fdt_status_okay_by_alias(fdt, "emi1_slot2");
+ } else if (mdio_mux[port] == EMI1_SLOT3) {
+ sprintf(alias, "phy_sgmii_s3_%x", phy);
+ fdt_set_phy_handle(fdt, compat, addr, alias);
+ fdt_status_okay_by_alias(fdt, "emi1_slot3");
+ }
break;
case FM1_DTSEC5:
case FM1_DTSEC6:
@@ -226,8 +255,8 @@ void fdt_fixup_board_enet(void *fdt)
}
/*
- * This function reads RCW to check if Serdes1{E,F,G,H} is configured
- * as slot 1/2/3 and update the lane_to_slot[] array accordingly
+ * This function reads RCW to check if Serdes1{A:H} is configured
+ * to slot 1/2/3/4/5/6/7 and update the lane_to_slot[] array accordingly
*/
static void initialize_lane_to_slot(void)
{
@@ -238,6 +267,7 @@ static void initialize_lane_to_slot(void)
srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
switch (srds_s1) {
+#if defined(CONFIG_T2080QDS)
case 0x51:
case 0x5f:
case 0x65:
@@ -264,6 +294,31 @@ static void initialize_lane_to_slot(void)
lane_to_slot[6] = 3;
lane_to_slot[7] = 3;
break;
+#elif defined(CONFIG_T2081QDS)
+ case 0x6b:
+ lane_to_slot[4] = 1;
+ lane_to_slot[5] = 3;
+ lane_to_slot[6] = 3;
+ lane_to_slot[7] = 3;
+ break;
+ case 0xca:
+ case 0xcb:
+ lane_to_slot[1] = 7;
+ lane_to_slot[2] = 6;
+ lane_to_slot[3] = 5;
+ lane_to_slot[5] = 3;
+ lane_to_slot[6] = 3;
+ lane_to_slot[7] = 3;
+ break;
+ case 0xf2:
+ lane_to_slot[1] = 7;
+ lane_to_slot[2] = 7;
+ lane_to_slot[3] = 7;
+ lane_to_slot[5] = 4;
+ lane_to_slot[6] = 3;
+ lane_to_slot[7] = 7;
+ break;
+#endif
default:
break;
}
@@ -305,14 +360,20 @@ int board_eth_init(bd_t *bis)
fm_memac_mdio_init(bis, &tgec_mdio_info);
/* Register the muxing front-ends to the MDIO buses */
- T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII1);
- T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII2);
- T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1);
- T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2);
- T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT3);
- T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT4);
- T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT5);
- T2080qds_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME, EMI2);
+ t208xqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII1);
+ t208xqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII2);
+ t208xqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1);
+ t208xqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2);
+ t208xqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT3);
+#if defined(CONFIG_T2080QDS)
+ t208xqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT4);
+#endif
+ t208xqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT5);
+#if defined(CONFIG_T2081QDS)
+ t208xqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT6);
+ t208xqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT7);
+#endif
+ t208xqds_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME, EMI2);
/* Set the two on-board RGMII PHY address */
fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY1_ADDR);
@@ -327,21 +388,21 @@ int board_eth_init(bd_t *bis)
case 0x95:
case 0xa2:
case 0x94:
- /* SGMII in Slot3 */
+ /* T2080QDS: SGMII in Slot3; T2081QDS: SGMII in Slot2 */
fm_info_set_phy_address(FM1_DTSEC9, SGMII_CARD_PORT1_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC10, SGMII_CARD_PORT2_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT3_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT4_PHY_ADDR);
- /* SGMII in Slot2 */
+ /* T2080QDS: SGMII in Slot2; T2081QDS: SGMII in Slot1 */
fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT4_PHY_ADDR);
break;
case 0x51:
case 0x5f:
case 0x65:
- /* XAUI/HiGig in Slot3 */
+ /* T2080QDS: XAUI/HiGig in Slot3; T2081QDS: in Slot2 */
fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
- /* SGMII in Slot2 */
+ /* T2080QDS: SGMII in Slot2; T2081QDS: in Slot3 */
fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT4_PHY_ADDR);
break;
@@ -365,7 +426,7 @@ int board_eth_init(bd_t *bis)
fm_info_set_phy_address(FM1_10GEC2, 5);
fm_info_set_phy_address(FM1_10GEC3, 6);
fm_info_set_phy_address(FM1_10GEC4, 7);
- /* SGMII in Slot2 */
+ /* T2080QDS: SGMII in Slot2; T2081QDS: in Slot3 */
fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR);
break;
@@ -373,7 +434,7 @@ int board_eth_init(bd_t *bis)
case 0x6d:
fm_info_set_phy_address(FM1_10GEC1, 4);
fm_info_set_phy_address(FM1_10GEC2, 5);
- /* SGMII in Slot3 */
+ /* T2080QDS: SGMII in Slot3; T2081QDS: in Slot2 */
fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT3_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT4_PHY_ADDR);
break;
@@ -408,6 +469,7 @@ int board_eth_init(bd_t *bis)
fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT3_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT4_PHY_ADDR);
break;
+#if defined(CONFIG_T2080QDS)
case 0xd9:
case 0xd3:
case 0xcb:
@@ -419,6 +481,27 @@ int board_eth_init(bd_t *bis)
fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR);
break;
+#elif defined(CONFIG_T2081QDS)
+ case 0xca:
+ case 0xcb:
+ /* SGMII in Slot3 */
+ fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR);
+ /* SGMII in Slot5 */
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
+ /* SGMII in Slot6 */
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
+ /* SGMII in Slot7 */
+ fm_info_set_phy_address(FM1_DTSEC10, SGMII_CARD_PORT3_PHY_ADDR);
+ break;
+#endif
+ case 0xf2:
+ /* T2080QDS: SGMII in Slot3; T2081QDS: SGMII in Slot7 */
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT2_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC10, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT4_PHY_ADDR);
+ break;
default:
break;
}
@@ -452,8 +535,25 @@ int board_eth_init(bd_t *bis)
case 3:
mdio_mux[i] = EMI1_SLOT3;
fm_info_set_mdio(i, mii_dev_for_muxval(
- mdio_mux[i]));
+ mdio_mux[i]));
+ break;
+#if defined(CONFIG_T2081QDS)
+ case 5:
+ mdio_mux[i] = EMI1_SLOT5;
+ fm_info_set_mdio(i, mii_dev_for_muxval(
+ mdio_mux[i]));
+ break;
+ case 6:
+ mdio_mux[i] = EMI1_SLOT6;
+ fm_info_set_mdio(i, mii_dev_for_muxval(
+ mdio_mux[i]));
+ break;
+ case 7:
+ mdio_mux[i] = EMI1_SLOT7;
+ fm_info_set_mdio(i, mii_dev_for_muxval(
+ mdio_mux[i]));
break;
+#endif
}
break;
case PHY_INTERFACE_MODE_RGMII:
diff --git a/board/freescale/t2080qds/law.c b/board/freescale/t208xqds/law.c
similarity index 100%
rename from board/freescale/t2080qds/law.c
rename to board/freescale/t208xqds/law.c
diff --git a/board/freescale/t2080qds/pci.c b/board/freescale/t208xqds/pci.c
similarity index 100%
rename from board/freescale/t2080qds/pci.c
rename to board/freescale/t208xqds/pci.c
diff --git a/board/freescale/t2080qds/t2080_rcw.cfg b/board/freescale/t208xqds/t2080_rcw.cfg
similarity index 100%
rename from board/freescale/t2080qds/t2080_rcw.cfg
rename to board/freescale/t208xqds/t2080_rcw.cfg
diff --git a/board/freescale/t208xqds/t2081_rcw.cfg b/board/freescale/t208xqds/t2081_rcw.cfg
new file mode 100644
index 0000000..a2d5ecf
--- /dev/null
+++ b/board/freescale/t208xqds/t2081_rcw.cfg
@@ -0,0 +1,8 @@
+#PBL preamble and RCW header
+aa55aa55 010e0100
+#Default SerDes Protocol: 0x6C
+#Core/DDR: 1533Mhz/2133MT/s
+12100017 15000000 00000000 00000000
+6c000002 00008000 e8104000 c1000000
+00000000 00000000 00000000 000307fc
+00000000 00000000 00000000 00000004
diff --git a/board/freescale/t2080qds/t2080_pbi.cfg b/board/freescale/t208xqds/t208x_pbi.cfg
similarity index 100%
rename from board/freescale/t2080qds/t2080_pbi.cfg
rename to board/freescale/t208xqds/t208x_pbi.cfg
diff --git a/board/freescale/t2080qds/t2080qds.c b/board/freescale/t208xqds/t208xqds.c
similarity index 80%
rename from board/freescale/t2080qds/t2080qds.c
rename to board/freescale/t208xqds/t208xqds.c
index 4fe8ccb..9cfc0bd 100644
--- a/board/freescale/t2080qds/t2080qds.c
+++ b/board/freescale/t208xqds/t208xqds.c
@@ -20,8 +20,8 @@
#include "../common/qixis.h"
#include "../common/vsc3316_3308.h"
-#include "t2080qds.h"
-#include "t2080qds_qixis.h"
+#include "t208xqds.h"
+#include "t208xqds_qixis.h"
DECLARE_GLOBAL_DATA_PTR;
@@ -89,19 +89,22 @@ int select_i2c_ch_pca9547(u8 ch)
int brd_mux_lane_to_slot(void)
{
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 srds_prtcl_s1, srds_prtcl_s2;
+ u32 srds_prtcl_s1;
srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) &
FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
- srds_prtcl_s2 = in_be32(&gur->rcwsr[4]) &
+#if defined(CONFIG_T2080QDS)
+ u32 srds_prtcl_s2 = in_be32(&gur->rcwsr[4]) &
FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
srds_prtcl_s2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
+#endif
switch (srds_prtcl_s1) {
case 0:
/* SerDes1 is not enabled */
break;
+#if defined(CONFIG_T2080QDS)
case 0x1c:
case 0xa2:
/* SD1(A:D) => SLOT3 SGMII
@@ -180,12 +183,89 @@ int brd_mux_lane_to_slot(void)
*/
QIXIS_WRITE(brdcfg[12], 0x1a);
break;
+#elif defined(CONFIG_T2081QDS)
+ case 0x51:
+ /* SD1(A:D) => SLOT2 XAUI
+ * SD1(E) => SLOT1 PCIe4 x1
+ * SD1(F:H) => SLOT3 SGMII
+ */
+ QIXIS_WRITE(brdcfg[12], 0x98);
+ QIXIS_WRITE(brdcfg[13], 0x70);
+ break;
+ case 0x6b:
+ /* SD1(A:D) => XFI SFP Module
+ * SD1(E) => SLOT1 PCIe4 x1
+ * SD1(F:H) => SLOT3 SGMII
+ */
+ QIXIS_WRITE(brdcfg[12], 0x80);
+ QIXIS_WRITE(brdcfg[13], 0x70);
+ break;
+ case 0x6c:
+ /* SD1(A:B) => XFI SFP Module
+ * SD1(C:D) => SLOT2 SGMII
+ * SD1(E:H) => SLOT1 PCIe4 x4
+ */
+ QIXIS_WRITE(brdcfg[12], 0xe8);
+ QIXIS_WRITE(brdcfg[13], 0x0);
+ break;
+ case 0x6d:
+ /* SD1(A:B) => XFI SFP Module
+ * SD1(C:D) => SLOT2 SGMII
+ * SD1(E:H) => SLOT1 PCIe4 x4
+ */
+ QIXIS_WRITE(brdcfg[12], 0xe8);
+ QIXIS_WRITE(brdcfg[13], 0x0);
+ break;
+ case 0xaa:
+ case 0xab:
+ /* SD1(A:D) => SLOT2 PCIe3 x4
+ * SD1(F:H) => SLOT1 SGMI4 x4
+ */
+ QIXIS_WRITE(brdcfg[12], 0xf8);
+ QIXIS_WRITE(brdcfg[13], 0x0);
+ break;
+ case 0xca:
+ case 0xcb:
+ /* SD1(A) => SLOT2 PCIe3 x1
+ * SD1(B) => SLOT7 SGMII
+ * SD1(C) => SLOT6 SGMII
+ * SD1(D) => SLOT5 SGMII
+ * SD1(E) => SLOT1 PCIe4 x1
+ * SD1(F:H) => SLOT3 SGMII
+ */
+ QIXIS_WRITE(brdcfg[12], 0x80);
+ QIXIS_WRITE(brdcfg[13], 0x70);
+ break;
+ case 0xde:
+ case 0xdf:
+ /* SD1(A:D) => SLOT2 PCIe3 x4
+ * SD1(E) => SLOT1 PCIe4 x1
+ * SD1(F) => SLOT4 PCIe1 x1
+ * SD1(G) => SLOT3 PCIe2 x1
+ * SD1(H) => SLOT7 SGMII
+ */
+ QIXIS_WRITE(brdcfg[12], 0x98);
+ QIXIS_WRITE(brdcfg[13], 0x25);
+ break;
+ case 0xf2:
+ /* SD1(A) => SLOT2 PCIe3 x1
+ * SD1(B:D) => SLOT7 SGMII
+ * SD1(E) => SLOT1 PCIe4 x1
+ * SD1(F) => SLOT4 PCIe1 x1
+ * SD1(G) => SLOT3 PCIe2 x1
+ * SD1(H) => SLOT7 SGMII
+ */
+ QIXIS_WRITE(brdcfg[12], 0x81);
+ QIXIS_WRITE(brdcfg[13], 0xa5);
+ break;
+#endif
default:
printf("WARNING: unsupported for SerDes1 Protocol %d\n",
srds_prtcl_s1);
return -1;
}
+#ifdef CONFIG_T2080QDS
switch (srds_prtcl_s2) {
case 0:
/* SerDes2 is not enabled */
@@ -241,6 +321,7 @@ int brd_mux_lane_to_slot(void)
srds_prtcl_s2);
return -1;
}
+#endif
return 0;
}
diff --git a/board/freescale/t2080qds/t2080qds.h b/board/freescale/t208xqds/t208xqds.h
similarity index 100%
rename from board/freescale/t2080qds/t2080qds.h
rename to board/freescale/t208xqds/t208xqds.h
diff --git a/board/freescale/t2080qds/t2080qds_qixis.h b/board/freescale/t208xqds/t208xqds_qixis.h
similarity index 90%
rename from board/freescale/t2080qds/t2080qds_qixis.h
rename to board/freescale/t208xqds/t208xqds_qixis.h
index fc83da7..bdcdc12 100644
--- a/board/freescale/t2080qds/t2080qds_qixis.h
+++ b/board/freescale/t208xqds/t208xqds_qixis.h
@@ -4,10 +4,10 @@
* SPDX-License-Identifier: GPL-2.0+
*/
-#ifndef __T2080QDS_QIXIS_H__
-#define __T2080QDS_QIXIS_H__
+#ifndef __T208xQDS_QIXIS_H__
+#define __T208xQDS_QIXIS_H__
-/* Definitions of QIXIS Registers for T2080QDS */
+/* Definitions of QIXIS Registers for T208xQDS */
#define QIXIS_SRDS1CLK_122 0x5a
#define QIXIS_SRDS1CLK_125 0x5e
@@ -35,6 +35,8 @@
#define BRDCFG5_IRE 0x20 /* i2c Remote i2c1 enable */
+#define BRDCFG9_SFP_TX_EN 0x10
+
#define BRDCFG12_SD3EN_MASK 0x20
#define BRDCFG12_SD3MX_MASK 0x08
#define BRDCFG12_SD3MX_SLOT5 0x08
diff --git a/board/freescale/t2080qds/tlb.c b/board/freescale/t208xqds/tlb.c
similarity index 100%
rename from board/freescale/t2080qds/tlb.c
rename to board/freescale/t208xqds/tlb.c
diff --git a/boards.cfg b/boards.cfg
index 706ec96..b169510 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -972,11 +972,16 @@ Active powerpc mpc85xx - freescale p2041rdb
Active powerpc mpc85xx - freescale t1040qds T1040QDS T1040QDS:PPC_T1040 Poonam Aggrwal <poonam.aggrwal at freescale.com>
Active powerpc mpc85xx - freescale t104xrdb T1040RDB T1040RDB:PPC_T1040 Poonam Aggrwal <poonam.aggrwal at freescale.com>
Active powerpc mpc85xx - freescale t104xrdb T1042RDB_PI T1042RDB_PI:PPC_T1042 Poonam Aggrwal <poonam.aggrwal at freescale.com>
-Active powerpc mpc85xx - freescale t2080qds T2080QDS T2080QDS:PPC_T2080 -
-Active powerpc mpc85xx - freescale t2080qds T2080QDS_NAND T2080QDS:PPC_T2080,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF40000 -
-Active powerpc mpc85xx - freescale t2080qds T2080QDS_SDCARD T2080QDS:PPC_T2080,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF40000 -
-Active powerpc mpc85xx - freescale t2080qds T2080QDS_SPIFLASH T2080QDS:PPC_T2080,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF40000 -
-Active powerpc mpc85xx - freescale t2080qds T2080QDS_SRIO_PCIE_BOOT T2080QDS:PPC_T2080,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF40000 -
+Active powerpc mpc85xx - freescale t208xqds T2080QDS T208xQDS:PPC_T2080
+Active powerpc mpc85xx - freescale t208xqds T2080QDS_SDCARD T208xQDS:PPC_T2080,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF40000
+Active powerpc mpc85xx - freescale t208xqds T2080QDS_SPIFLASH T208xQDS:PPC_T2080,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF40000
+Active powerpc mpc85xx - freescale t208xqds T2080QDS_NAND T208xQDS:PPC_T2080,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF40000
+Active powerpc mpc85xx - freescale t208xqds T2080QDS_SRIO_PCIE_BOOT T208xQDS:PPC_T2080,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF40000
+Active powerpc mpc85xx - freescale t208xqds T2081QDS T208xQDS:PPC_T2081
+Active powerpc mpc85xx - freescale t208xqds T2081QDS_SDCARD T208xQDS:PPC_T2081,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF40000
+Active powerpc mpc85xx - freescale t208xqds T2081QDS_SPIFLASH T208xQDS:PPC_T2081,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF40000
+Active powerpc mpc85xx - freescale t208xqds T2081QDS_NAND T208xQDS:PPC_T2081,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF40000
+Active powerpc mpc85xx - freescale t208xqds T2081QDS_SRIO_PCIE_BOOT T208xQDS:PPC_T2081,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF40000
Active powerpc mpc85xx - freescale t4qds T4160QDS T4240QDS:PPC_T4160 -
Active powerpc mpc85xx - freescale t4qds T4160QDS_SDCARD T4240QDS:PPC_T4160,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF40000 -
Active powerpc mpc85xx - freescale t4qds T4160QDS_SPIFLASH T4240QDS:PPC_T4160,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF40000 -
diff --git a/include/configs/T2080QDS.h b/include/configs/T208xQDS.h
similarity index 97%
rename from include/configs/T2080QDS.h
rename to include/configs/T208xQDS.h
index 9bd0fe2..36afe9e 100644
--- a/include/configs/T2080QDS.h
+++ b/include/configs/T208xQDS.h
@@ -5,21 +5,25 @@
*/
/*
- * T2080 QDS board configuration file
+ * T2080/T2081 QDS board configuration file
*/
-#ifndef __T2080QDS_H
-#define __T2080QDS_H
+#ifndef __T208xQDS_H
+#define __T208xQDS_H
-#define CONFIG_T2080QDS
#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
#define CONFIG_MMC
#define CONFIG_SPI_FLASH
#define CONFIG_USB_EHCI
+#if defined(CONFIG_PPC_T2080)
+#define CONFIG_T2080QDS
#define CONFIG_FSL_SATA_V2
#define CONFIG_SYS_SRIO /* Enable Serial RapidIO Support */
#define CONFIG_SRIO1 /* SRIO port 1 */
#define CONFIG_SRIO2 /* SRIO port 2 */
+#elif defined(CONFIG_PPC_T2081)
+#define CONFIG_T2081QDS
+#endif
/* High Level Configuration Options */
#define CONFIG_PHYS_64BIT
@@ -44,8 +48,12 @@
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
-#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t2080qds/t2080_pbi.cfg
-#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t2080qds/t2080_rcw.cfg
+#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t208xqds/t208x_pbi.cfg
+#if defined(CONFIG_PPC_T2080)
+#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t208xqds/t2080_rcw.cfg
+#elif defined(CONFIG_PPC_T2081)
+#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t208xqds/t2081_rcw.cfg
+#endif
#endif
#define CONFIG_SRIO_PCIE_BOOT_MASTER
@@ -447,7 +455,12 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_FSL_ESPI
#define CONFIG_SPI_FLASH_SST
#define CONFIG_SPI_FLASH_STMICRO
+#if defined(CONFIG_T2080QDS)
#define CONFIG_SPI_FLASH_SPANSION
+#elif defined(CONFIG_T2081QDS)
+#define CONFIG_SPI_FLASH_EON
+#endif
+
#define CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE 0
@@ -505,7 +518,7 @@ unsigned long get_board_ddr_clk(void);
#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata LSZ ADD */
+#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
#define CONFIG_NET_MULTI
#define CONFIG_E1000
#define CONFIG_PCI_PNP /* do pci plug-and-play */
@@ -801,4 +814,4 @@ unsigned long get_board_ddr_clk(void);
#undef CONFIG_CMD_USB
#endif
-#endif /* __T2080QDS_H */
+#endif /* __T208xQDS_H */
--
1.8.0
More information about the U-Boot
mailing list