[U-Boot] [PATCH v4 2/3] wandboard: add Future Eletronics 7" WVGA LCD extension board
Otavio Salvador
otavio at ossystems.com.br
Fri Jan 3 18:58:22 CET 2014
This adds support for the 7" WVGA produced by Future Eletronics and
make it dynamically detect if it is connected or not based on the
touchscreen controller.
Signed-off-by: Otavio Salvador <otavio at ossystems.com.br>
---
Changes in v4: None
Changes in v3:
- rebased on imx/master
Changes in v2: None
board/wandboard/wandboard.c | 240 +++++++++++++++++++++++++++++++++++++++-----
include/configs/wandboard.h | 35 ++++++-
2 files changed, 251 insertions(+), 24 deletions(-)
diff --git a/board/wandboard/wandboard.c b/board/wandboard/wandboard.c
index 0043bc6..7debf30 100644
--- a/board/wandboard/wandboard.c
+++ b/board/wandboard/wandboard.c
@@ -15,6 +15,7 @@
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
#include <asm/imx-common/boot_mode.h>
#include <asm/io.h>
#include <asm/sizes.h>
@@ -25,6 +26,7 @@
#include <miiphy.h>
#include <netdev.h>
#include <linux/fb.h>
+#include <i2c.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -39,6 +41,10 @@ DECLARE_GLOBAL_DATA_PTR;
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
+ PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
#define USDHC1_CD_GPIO IMX_GPIO_NR(1, 2)
#define USDHC3_CD_GPIO IMX_GPIO_NR(3, 9)
#define ETH_PHY_RESET IMX_GPIO_NR(3, 29)
@@ -208,50 +214,236 @@ int board_phy_config(struct phy_device *phydev)
}
#if defined(CONFIG_VIDEO_IPUV3)
-static struct fb_videomode const hdmi = {
- .name = "HDMI",
- .refresh = 60,
- .xres = 1024,
- .yres = 768,
- .pixclock = 15385,
- .left_margin = 220,
- .right_margin = 40,
- .upper_margin = 21,
- .lower_margin = 7,
- .hsync_len = 60,
- .vsync_len = 10,
- .sync = FB_SYNC_EXT,
- .vmode = FB_VMODE_NONINTERLACED
+struct i2c_pads_info i2c_pad_info = {
+ .scl = {
+ .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL
+ | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12
+ | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ .gp = IMX_GPIO_NR(4, 12)
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA
+ | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13
+ | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ .gp = IMX_GPIO_NR(4, 13)
+ }
};
-int board_video_skip(void)
-{
- int ret;
+static iomux_v3_cfg_t const fwadapt_7wvga_pads[] = {
+ MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK,
+ MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02, /* HSync */
+ MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03, /* VSync */
+ MX6_PAD_DI0_PIN4__IPU1_DI0_PIN04
+ | MUX_PAD_CTRL(PAD_CTL_DSE_120ohm), /* Contrast */
+ MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15, /* DISP0_DRDY */
+
+ MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00,
+ MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01,
+ MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02,
+ MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03,
+ MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04,
+ MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05,
+ MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06,
+ MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07,
+ MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08,
+ MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09,
+ MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10,
+ MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11,
+ MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12,
+ MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13,
+ MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14,
+ MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15,
+ MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16,
+ MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17,
+
+ MX6_PAD_SD4_DAT2__GPIO2_IO10
+ | MUX_PAD_CTRL(NO_PAD_CTRL), /* DISP0_BKLEN */
+ MX6_PAD_SD4_DAT3__GPIO2_IO11
+ | MUX_PAD_CTRL(NO_PAD_CTRL), /* DISP0_VDDEN */
+};
- ret = ipuv3_fb_init(&hdmi, 0, IPU_PIX_FMT_RGB24);
+struct display_info_t {
+ int bus;
+ int addr;
+ int pixfmt;
+ int (*detect)(struct display_info_t const *dev);
+ void (*enable)(struct display_info_t const *dev);
+ struct fb_videomode mode;
+};
- if (ret) {
- printf("HDMI cannot be configured: %d\n", ret);
- return ret;
- }
+static int detect_hdmi(struct display_info_t const *dev)
+{
+ struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
+ return readb(&hdmi->phy_stat0) & HDMI_DVI_STAT;
+}
+static void do_enable_hdmi(struct display_info_t const *dev)
+{
imx_enable_hdmi_phy();
+}
- return ret;
+static int detect_i2c(struct display_info_t const *dev)
+{
+ return ((0 == i2c_set_bus_num(dev->bus)) &&
+ (0 == i2c_probe(dev->addr)));
+}
+
+static void enable_fwadapt_7wvga(struct display_info_t const *dev)
+{
+ imx_iomux_v3_setup_multiple_pads(
+ fwadapt_7wvga_pads,
+ ARRAY_SIZE(fwadapt_7wvga_pads));
+
+ gpio_direction_output(IMX_GPIO_NR(2, 10), 1);
+ gpio_direction_output(IMX_GPIO_NR(2, 11), 1);
+}
+
+static struct display_info_t const displays[] = {{
+ .bus = -1,
+ .addr = 0,
+ .pixfmt = IPU_PIX_FMT_RGB24,
+ .detect = detect_hdmi,
+ .enable = do_enable_hdmi,
+ .mode = {
+ .name = "HDMI",
+ .refresh = 60,
+ .xres = 1024,
+ .yres = 768,
+ .pixclock = 15385,
+ .left_margin = 220,
+ .right_margin = 40,
+ .upper_margin = 21,
+ .lower_margin = 7,
+ .hsync_len = 60,
+ .vsync_len = 10,
+ .sync = FB_SYNC_EXT,
+ .vmode = FB_VMODE_NONINTERLACED
+} }, {
+ .bus = 0,
+ .addr = 0x10,
+ .pixfmt = IPU_PIX_FMT_RGB666,
+ .detect = detect_i2c,
+ .enable = enable_fwadapt_7wvga,
+ .mode = {
+ .name = "FWBADAPT-LCD-F07A-0102",
+ .refresh = 60,
+ .xres = 800,
+ .yres = 480,
+ .pixclock = 33260,
+ .left_margin = 128,
+ .right_margin = 128,
+ .upper_margin = 22,
+ .lower_margin = 22,
+ .hsync_len = 1,
+ .vsync_len = 1,
+ .sync = 0,
+ .vmode = FB_VMODE_NONINTERLACED
+} } };
+
+int board_video_skip(void)
+{
+ int i;
+ int ret;
+ int detected = 0;
+ char const *panel = getenv("panel");
+ if (!panel) {
+ for (i = 0; i < ARRAY_SIZE(displays); i++) {
+ struct display_info_t const *dev = displays+i;
+ if (dev->detect && dev->detect(dev)) {
+ panel = dev->mode.name;
+ detected = 1;
+ break;
+ }
+ }
+ if (!panel) {
+ panel = displays[0].mode.name;
+ printf("No panel detected: default to %s\n", panel);
+ i = 0;
+ }
+ } else {
+ for (i = 0; i < ARRAY_SIZE(displays); i++) {
+ if (!strcmp(panel, displays[i].mode.name))
+ break;
+ }
+ }
+ if (i < ARRAY_SIZE(displays)) {
+ ret = ipuv3_fb_init(&displays[i].mode, 0,
+ displays[i].pixfmt);
+
+ if (!ret) {
+ displays[i].enable(displays+i);
+ printf("Display: %s (%ux%u) %s\n",
+ displays[i].mode.name,
+ displays[i].mode.xres,
+ displays[i].mode.yres,
+ (detected ? "[auto]" : ""));
+ } else
+ printf("LCD %s cannot be configured: %d\n",
+ displays[i].mode.name, ret);
+ } else {
+ printf("unsupported panel %s\n", panel);
+ return -EINVAL;
+ }
+
+ return 0;
}
static void setup_display(void)
{
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
int reg;
enable_ipu_clock();
imx_setup_hdmi();
+ /* Turn on LDB0, LDB1, IPU,IPU DI0 clocks */
+ reg = __raw_readl(&mxc_ccm->CCGR3);
+ reg |= MXC_CCM_CCGR3_LDB_DI0_MASK | MXC_CCM_CCGR3_LDB_DI1_MASK;
+ writel(reg, &mxc_ccm->CCGR3);
+
+ /* set LDB0, LDB1 clk select to 011/011 */
+ reg = readl(&mxc_ccm->cs2cdr);
+ reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
+ | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+ reg |= (3 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
+ | (3 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
+ writel(reg, &mxc_ccm->cs2cdr);
+
+ reg = readl(&mxc_ccm->cscmr2);
+ reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV | MXC_CCM_CSCMR2_LDB_DI1_IPU_DIV;
+ writel(reg, &mxc_ccm->cscmr2);
+
reg = readl(&mxc_ccm->chsccdr);
reg |= (CHSCCDR_CLK_SEL_LDB_DI0
<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+ reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+ << MXC_CCM_CHSCCDR_IPU1_DI1_CLK_SEL_OFFSET);
writel(reg, &mxc_ccm->chsccdr);
+
+ reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
+ | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_LOW
+ | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW
+ | IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG
+ | IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT
+ | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
+ | IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT
+ | IOMUXC_GPR2_LVDS_CH0_MODE_DISABLED
+ | IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0;
+ writel(reg, &iomux->gpr[2]);
+
+ reg = readl(&iomux->gpr[3]);
+ reg = (reg & ~(IOMUXC_GPR3_LVDS1_MUX_CTL_MASK
+ | IOMUXC_GPR3_HDMI_MUX_CTL_MASK))
+ | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
+ << IOMUXC_GPR3_LVDS1_MUX_CTL_OFFSET);
+ writel(reg, &iomux->gpr[3]);
+
+ /* Disable LCD backlight */
+ imx_iomux_v3_setup_pad(MX6_PAD_DI0_PIN4__GPIO4_IO20);
+ gpio_direction_input(IMX_GPIO_NR(4, 20));
}
#endif /* CONFIG_VIDEO_IPUV3 */
@@ -309,6 +501,8 @@ int board_init(void)
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+ setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info);
+
return 0;
}
diff --git a/include/configs/wandboard.h b/include/configs/wandboard.h
index ae8480d..5134b2e 100644
--- a/include/configs/wandboard.h
+++ b/include/configs/wandboard.h
@@ -56,6 +56,12 @@
#define CONFIG_LOADADDR 0x12000000
#define CONFIG_SYS_TEXT_BASE 0x17800000
+/* I2C Configs */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_SPEED 100000
+
/* MMC Configuration */
#define CONFIG_FSL_ESDHC
#define CONFIG_FSL_USDHC
@@ -98,6 +104,7 @@
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_IPUV3_CLK 260000000
+#define CONFIG_CMD_HDMIDETECT
#define CONFIG_IMX_HDMI
#if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
@@ -135,7 +142,33 @@
"fi; " \
"fi\0" \
"mmcargs=setenv bootargs console=${console},${baudrate} " \
- "root=${mmcroot}\0" \
+ "root=${mmcroot}; run videoargs\0" \
+ "videoargs=" \
+ "setenv nextcon 0; " \
+ "if hdmidet; then " \
+ "setenv bootargs ${bootargs} " \
+ "video=mxcfb${nextcon}:dev=hdmi,1280x720M at 60," \
+ "if=RGB24; " \
+ "setenv fbmen fbmem=28M; " \
+ "setexpr nextcon ${nextcon} + 1; " \
+ "else " \
+ "echo - no HDMI monitor;" \
+ "fi; " \
+ "i2c dev 0; " \
+ "if i2c probe 0x10; then " \
+ "setenv bootargs ${bootargs} " \
+ "video=mxcfb${nextcon}:dev=lcd,800x480 at 60," \
+ "if=RGB666; " \
+ "if test 0 -eq ${nextcon}; then " \
+ "setenv fbmem fbmem=10M; " \
+ "else " \
+ "setenv fbmem ${fbmem},10M; " \
+ "fi; " \
+ "setexpr nextcon ${nextcon} + 1; " \
+ "else " \
+ "echo '- no FWBADAPT-7WVGA-LCD-F07A-0102 display';" \
+ "fi; " \
+ "setenv bootargs ${bootargs} ${fbmem}\0" \
"loadbootscript=" \
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
--
1.8.5.2
More information about the U-Boot
mailing list