[U-Boot] [PATCH v3 2/2] usb: exynos5: arndale: Add network support

[Inderpal Singh]

Arndale board has AX88760, which is USB 2.0 Hub & USB 2.0 Ethernet Combo
controller, connected to HSIC Phy of USB host controller via USB3503 hub.

This patch uses board specific board_usb_init function to perform reset
sequence for USB3503 hub and enables the relevant config options for
network to work.

Signed-off-by: Inderpal Singh <inderpal.singh at linaro.org>
Signed-off-by: Chander Kashyap <chander.kashyap at linaro.org>
---
 board/samsung/arndale/arndale.c |   21 +++++++++++++++++++++
 drivers/usb/host/ehci-exynos.c  |    2 ++
 include/configs/arndale.h       |    4 ++++
 3 files changed, 27 insertions(+)

diff --git a/board/samsung/arndale/arndale.c b/board/samsung/arndale/arndale.c
index 052fecd..9efc355 100644
--- a/board/samsung/arndale/arndale.c
+++ b/board/samsung/arndale/arndale.c
@@ -5,12 +5,33 @@
  */
 
 #include <common.h>
+#include <usb.h>
 #include <asm/arch/pinmux.h>
 #include <asm/arch/dwmmc.h>
+#include <asm/arch/gpio.h>
 #include <asm/arch/power.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#ifdef CONFIG_USB_EHCI_EXYNOS
+int board_usb_init(int index, enum usb_init_type init)
+{
+	struct exynos5_gpio_part1 *gpio = (struct exynos5_gpio_part1 *)
+						samsung_get_base_gpio_part1();
+
+	/* Configure gpios for usb 3503 hub:
+	 * disconnect, toggle reset and connect
+	 */
+	s5p_gpio_direction_output(&gpio->d1, 7, 0);
+	s5p_gpio_direction_output(&gpio->x3, 5, 0);
+
+	s5p_gpio_direction_output(&gpio->x3, 5, 1);
+	s5p_gpio_direction_output(&gpio->d1, 7, 1);
+
+	return 0;
+}
+#endif
+
 int board_init(void)
 {
 	gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
diff --git a/drivers/usb/host/ehci-exynos.c b/drivers/usb/host/ehci-exynos.c
index 88e6466..9356878 100644
--- a/drivers/usb/host/ehci-exynos.c
+++ b/drivers/usb/host/ehci-exynos.c
@@ -203,6 +203,8 @@ int ehci_hcd_init(int index, enum usb_init_type init,
 
 	setup_usb_phy(ctx->usb);
 
+	board_usb_init(index, init);
+
 	*hccr = ctx->hcd;
 	*hcor = (struct ehci_hcor *)((uint32_t) *hccr
 				+ HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
diff --git a/include/configs/arndale.h b/include/configs/arndale.h
index b7fb29e..eda0e4f 100644
--- a/include/configs/arndale.h
+++ b/include/configs/arndale.h
@@ -116,6 +116,10 @@
 #define CONFIG_USB_EHCI_EXYNOS
 #define CONFIG_USB_STORAGE
 
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	3
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+
 /* MMC SPL */
 #define CONFIG_EXYNOS_SPL
 #define CONFIG_SPL
-- 
1.7.9.5