[U-Boot] [PATCH v2] spi/cadence: Adding Cadence SPI driver support for SOCFPGA
Jagan Teki
jagannadh.teki at gmail.com
Wed Jan 8 13:13:20 CET 2014
Hi Chin Liang See,
On Thu, Jan 2, 2014 at 8:13 AM, Chin Liang See <clsee at altera.com> wrote:
> To add the Cadence SPI driver support for Altera SOCFPGA. It
> required information such as clocks and timing from platform's
> configuration header file within include/configs folder
>
> Signed-off-by: Chin Liang See <clsee at altera.com>
> Cc: Jagan Teki <jagannadh.teki at gmail.com>
> Cc: Gerhard Sittig <gsi at denx.de>
> ---
> Changes for v2
> - Combine driver into single C file instead of 2
> - Added documentation on the macro used
> - Using structure for registers instead of macro
> ---
> doc/README.socfpga | 47 ++
> drivers/spi/Makefile | 1 +
> drivers/spi/cadence_qspi.c | 1018 ++++++++++++++++++++++++++++++++++++++++++++
> drivers/spi/cadence_qspi.h | 170 ++++++++
> 4 files changed, 1236 insertions(+)
> create mode 100644 drivers/spi/cadence_qspi.c
> create mode 100644 drivers/spi/cadence_qspi.h
>
> diff --git a/doc/README.socfpga b/doc/README.socfpga
> index cfcbbfe..242af97 100644
> --- a/doc/README.socfpga
> +++ b/doc/README.socfpga
> @@ -51,3 +51,50 @@ the card
> #define CONFIG_SOCFPGA_DWMMC_BUS_HZ 50000000
> -> The clock rate to controller. Do note the controller have a wrapper which
> divide the clock from PLL by 4.
> +
> +--------------------------------------------
> +cadence_qspi
> +--------------------------------------------
> +Here are macro and detailed configuration required to enable Cadence QSPI
> +controller support within SOCFPGA
> +
> +#define CONFIG_SPI_FLASH
> +-> To enable the SPI flash framework support
> +
> +#define CONFIG_CMD_SF
> +-> To enable the console support for SPI flash
> +
> +#define CONFIG_SF_DEFAULT_SPEED (50000000)
> +-> To set the target SPI clock frequency in Hz
> +
> +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
> +-> To set the SPI mode (CPOL & CPHA). Normally use mode 3 for serial NOR flash
> +
> +#define CONFIG_SPI_FLASH_QUAD (1)
> +-> To enable the Quad IO mode for performance boost
> +
> +#define CONFIG_SPI_FLASH_STMICRO
> +#define CONFIG_SPI_FLASH_SPANSION
> +-> To enable the SPI flash support for vendor Micron and Spansion
> +
> +#define CONFIG_CQSPI_BASE (SOCFPGA_QSPIREGS_ADDRESS)
> +#define CONFIG_CQSPI_AHB_BASE (SOCFPGA_QSPIDATA_ADDRESS)
> +-> To specify the base address for controller CSR base and AHB data base addr
> +
> +#define CONFIG_CQSPI_REF_CLK (400000000)
> +-> The clock frequency supplied from PLL to the QSPI controller
> +
> +#define CONFIG_CQSPI_PAGE_SIZE (256)
> +-> To define the page size of serial flash in bytes
> +
> +#define CONFIG_CQSPI_BLOCK_SIZE (16)
> +-> To define the block size of serial flash in pages
> +
> +#define CONFIG_CQSPI_DECODER (0)
> +-> To enable the 4-to-16 decoder which enable up to 16 serial flash devices
> +
> +#define CONFIG_CQSPI_TSHSL_NS (200)
> +#define CONFIG_CQSPI_TSD2D_NS (255)
> +#define CONFIG_CQSPI_TCHSH_NS (20)
> +#define CONFIG_CQSPI_TSLCH_NS (20)
> +-> Configure the controller based on serial flash device timing characteristic
Do we really require this, because most of the known macros definitions.
Better to not write too many duplicates - Yes there are few macro's
which are specific to cadence
but I don't think those were required.
> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
> index ed4ecd7..b8d56ea 100644
> --- a/drivers/spi/Makefile
> +++ b/drivers/spi/Makefile
> @@ -15,6 +15,7 @@ obj-$(CONFIG_ATMEL_DATAFLASH_SPI) += atmel_dataflash_spi.o
> obj-$(CONFIG_ATMEL_SPI) += atmel_spi.o
> obj-$(CONFIG_BFIN_SPI) += bfin_spi.o
> obj-$(CONFIG_BFIN_SPI6XX) += bfin_spi6xx.o
> +obj-$(CONFIG_CADENCE_QSPI) += cadence_qspi.o
> obj-$(CONFIG_CF_SPI) += cf_spi.o
> obj-$(CONFIG_CF_QSPI) += cf_qspi.o
> obj-$(CONFIG_DAVINCI_SPI) += davinci_spi.o
> diff --git a/drivers/spi/cadence_qspi.c b/drivers/spi/cadence_qspi.c
> new file mode 100644
> index 0000000..4712b45
> --- /dev/null
> +++ b/drivers/spi/cadence_qspi.c
> @@ -0,0 +1,1018 @@
> +/*
> + * (C) Copyright 2014 Altera Corporation <www.altera.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <asm/io.h>
> +#include <asm/errno.h>
> +#include <malloc.h>
> +#include <spi.h>
> +#include "cadence_qspi.h"
Try to move the stuff from header here.!
> +
> +static int qspi_is_init;
> +static unsigned int qspi_calibrated_hz;
> +static unsigned int qspi_calibrated_cs;
> +
> +static const struct cadence_qspi *cadence_qspi_base = (void *)QSPI_BASE;
> +
> +#define to_cadence_qspi_slave(s) \
> + container_of(s, struct cadence_qspi_slave, slave)
> +
> +#define CQSPI_CAL_DELAY(tdelay_ns, tref_ns, tsclk_ns) \
> + ((((tdelay_ns) - (tsclk_ns)) / (tref_ns)))
> +
> +#define CQSPI_GET_WR_SRAM_LEVEL() \
> + ((readl(&cadence_qspi_base->sramfill) >> \
> + CQSPI_REG_SRAMLEVEL_WR_LSB) & CQSPI_REG_SRAMLEVEL_WR_MASK)
> +
> +static unsigned int cadence_qspi_apb_cmd2addr(const unsigned char *addr_buf,
> + unsigned int addr_width)
> +{
> + unsigned int addr;
> +
> + addr = (addr_buf[0] << 16) | (addr_buf[1] << 8) | addr_buf[2];
> +
> + if (addr_width == 4)
> + addr = (addr << 8) | addr_buf[3];
> +
> + return addr;
> +}
> +
> +static void cadence_qspi_apb_read_fifo_data(void *dest,
> + const void *src_ahb_addr, unsigned int bytes)
> +{
> + unsigned int temp;
> + int remaining = bytes;
> + unsigned int *dest_ptr = (unsigned int *)dest;
> + unsigned int *src_ptr = (unsigned int *)src_ahb_addr;
> +
> + while (remaining > 0) {
> + if (remaining >= CQSPI_FIFO_WIDTH) {
> + *dest_ptr = readl(src_ptr);
> + remaining -= CQSPI_FIFO_WIDTH;
> + } else {
> + /* dangling bytes */
> + temp = readl(src_ptr);
> + memcpy(dest_ptr, &temp, remaining);
> + break;
> + }
> + dest_ptr++;
> + }
> +
> + return;
> +}
> +
> +static void cadence_qspi_apb_write_fifo_data(const void *dest_ahb_addr,
> + const void *src, unsigned int bytes)
> +{
> + unsigned int temp;
> + int remaining = bytes;
> + unsigned int *dest_ptr = (unsigned int *)dest_ahb_addr;
> + unsigned int *src_ptr = (unsigned int *)src;
> +
> + while (remaining > 0) {
> + if (remaining >= CQSPI_FIFO_WIDTH) {
> + writel(*src_ptr, dest_ptr);
> + remaining -= sizeof(unsigned int);
> + } else {
> + /* dangling bytes */
> + memcpy(&temp, src_ptr, remaining);
> + writel(temp, dest_ptr);
> + break;
> + }
> + src_ptr++;
> + }
> +
> + return;
> +}
> +
> +/* Read from SRAM FIFO with polling SRAM fill level. */
> +static int qspi_read_sram_fifo_poll(void *dest_addr,
> + const void *src_addr, unsigned int num_bytes)
> +{
> + unsigned int remaining = num_bytes;
> + unsigned int retry;
> + unsigned int sram_level = 0;
> + unsigned char *dest = (unsigned char *)dest_addr;
> +
> + while (remaining > 0) {
> + retry = CQSPI_REG_RETRY;
> + while (retry--) {
> + sram_level = (readl(&cadence_qspi_base->sramfill) >>
> + CQSPI_REG_SRAMLEVEL_RD_LSB) &
> + CQSPI_REG_SRAMLEVEL_RD_MASK;
> + if (sram_level)
> + break;
> + udelay(1);
> + }
> +
> + if (!retry) {
> + printf("QSPI: No receive data after polling for %d "
> + "times\n", CQSPI_REG_RETRY);
> + return -1;
> + }
> +
> + sram_level *= CQSPI_FIFO_WIDTH;
> + sram_level = sram_level > remaining ? remaining : sram_level;
> +
> + /* Read data from FIFO. */
> + cadence_qspi_apb_read_fifo_data(dest, src_addr, sram_level);
> + dest += sram_level;
> + remaining -= sram_level;
> + udelay(1);
> + }
> + return 0;
> +}
> +
> +
> +/* Write to SRAM FIFO with polling SRAM fill level. */
> +static int qpsi_write_sram_fifo_push(void *dest_addr,
> + const void *src_addr, unsigned int num_bytes)
> +{
> + unsigned int retry = CQSPI_REG_RETRY;
> + unsigned int sram_level;
> + unsigned int wr_bytes;
> + unsigned char *src = (unsigned char *)src_addr;
> + int remaining = num_bytes;
> + unsigned int page_size = CONFIG_CQSPI_PAGE_SIZE;
> + unsigned int sram_threshold_words = CQSPI_REG_SRAM_THRESHOLD_WORDS;
> +
> + while (remaining > 0) {
> + retry = CQSPI_REG_RETRY;
> + while (retry--) {
> + sram_level = CQSPI_GET_WR_SRAM_LEVEL();
> + if (sram_level <= sram_threshold_words)
> + break;
> + }
> + if (!retry) {
> + printf("QSPI: SRAM fill level (0x%08x) "
> + "not hit lower expected level (0x%08x)",
> + sram_level, sram_threshold_words);
> + return -1;
> + }
> + /* Write a page or remaining bytes. */
> + wr_bytes = (remaining > page_size) ?
> + page_size : remaining;
> +
> + cadence_qspi_apb_write_fifo_data(dest_addr, src, wr_bytes);
> + src += wr_bytes;
> + remaining -= wr_bytes;
> + }
> +
> + return 0;
> +}
> +
> +static void cadence_qspi_apb_controller_enable(void)
> +{
> + setbits_le32(&cadence_qspi_base->cfg, CQSPI_REG_CONFIG_ENABLE_MASK);
> +}
> +
> +static void cadence_qspi_apb_controller_disable(void)
> +{
> + clrbits_le32(&cadence_qspi_base->cfg, CQSPI_REG_CONFIG_ENABLE_MASK);
> +}
> +
> +/* Return 1 if idle, otherwise return 0 (busy). */
> +static unsigned int cadence_qspi_wait_idle(void)
> +{
> + unsigned int start, count = 0;
> + /* timeout in unit of ms */
> + unsigned int timeout = 5000;
> +
> + start = get_timer(0);
> + for ( ; get_timer(start) < timeout ; ) {
> + if ((readl(&cadence_qspi_base->cfg) >>
> + CQSPI_REG_CONFIG_IDLE_LSB) & 0x1)
> + count++;
> + else
> + count = 0;
> + /*
> + * Ensure the QSPI controller is in true idle state after
> + * reading back the same idle status consecutively
> + */
> + if (count >= CQSPI_POLL_IDLE_RETRY)
> + return 1;
> + }
> +
> + /* Timeout, still in busy mode. */
> + printf("QSPI: QSPI is still busy after poll for %d times.\n",
> + CQSPI_REG_RETRY);
> + return 0;
> +}
> +
> +static void cadence_qspi_apb_readdata_capture(unsigned int bypass,
> + unsigned int delay)
> +{
> + unsigned int reg;
> + cadence_qspi_apb_controller_disable();
> +
> + reg = readl(&cadence_qspi_base->rddatacap);
> +
> + if (bypass)
> + reg |= (1 << CQSPI_REG_RD_DATA_CAPTURE_BYPASS_LSB);
> + else
> + reg &= ~(1 << CQSPI_REG_RD_DATA_CAPTURE_BYPASS_LSB);
> +
> + reg &= ~(CQSPI_REG_RD_DATA_CAPTURE_DELAY_MASK
> + << CQSPI_REG_RD_DATA_CAPTURE_DELAY_LSB);
> +
> + reg |= ((delay & CQSPI_REG_RD_DATA_CAPTURE_DELAY_MASK)
> + << CQSPI_REG_RD_DATA_CAPTURE_DELAY_LSB);
> +
> + writel(reg, &cadence_qspi_base->rddatacap);
> +
> + cadence_qspi_apb_controller_enable();
> + return;
> +}
> +
> +static void cadence_qspi_apb_config_baudrate_div(unsigned int ref_clk_hz,
> + unsigned int sclk_hz)
> +{
> + unsigned int reg;
> + unsigned int div;
> +
> + cadence_qspi_apb_controller_disable();
> + reg = readl(&cadence_qspi_base->cfg);
> + reg &= ~(CQSPI_REG_CONFIG_BAUD_MASK << CQSPI_REG_CONFIG_BAUD_LSB);
> +
> + div = ref_clk_hz / sclk_hz;
> +
> + if (div > 32)
> + div = 32;
> +
> + /* Check if even number. */
> + if ((div & 1))
> + div = (div / 2);
> + else
> + div = (div / 2) - 1;
> +
> + debug("%s: ref_clk %dHz sclk %dHz Div 0x%x\n", __func__,
> + ref_clk_hz, sclk_hz, div);
> +
> + div = (div & CQSPI_REG_CONFIG_BAUD_MASK) << CQSPI_REG_CONFIG_BAUD_LSB;
> + reg |= div;
> + writel(reg, &cadence_qspi_base->cfg);
> +
> + cadence_qspi_apb_controller_enable();
> + return;
> +}
> +
> +static void cadence_qspi_apb_set_clk_mode(unsigned int clk_pol,
> + unsigned int clk_pha)
> +{
> + unsigned int reg;
> +
> + cadence_qspi_apb_controller_disable();
> + reg = readl(&cadence_qspi_base->cfg);
> + reg &= ~(1 <<
> + (CQSPI_REG_CONFIG_CLK_POL_LSB | CQSPI_REG_CONFIG_CLK_PHA_LSB));
> +
> + reg |= ((clk_pol & 0x1) << CQSPI_REG_CONFIG_CLK_POL_LSB);
> + reg |= ((clk_pha & 0x1) << CQSPI_REG_CONFIG_CLK_PHA_LSB);
> +
> + writel(reg, &cadence_qspi_base->cfg);
> +
> + cadence_qspi_apb_controller_enable();
> + return;
> +}
> +
> +static void cadence_qspi_apb_chipselect(unsigned int chip_select,
> + unsigned int decoder_enable)
> +{
> + unsigned int reg;
> +
> + cadence_qspi_apb_controller_disable();
> +
> + debug("%s : chipselect %d decode %d\n", __func__, chip_select,
> + decoder_enable);
> +
> + reg = readl(&cadence_qspi_base->cfg);
> + /* docoder */
> + if (decoder_enable)
> + reg |= CQSPI_REG_CONFIG_DECODE_MASK;
> + else {
> + reg &= ~CQSPI_REG_CONFIG_DECODE_MASK;
> + /* Convert CS if without decoder.
> + * CS0 to 4b'1110
> + * CS1 to 4b'1101
> + * CS2 to 4b'1011
> + * CS3 to 4b'0111
> + */
> + chip_select = 0xF & ~(1 << chip_select);
> + }
> +
> + reg &= ~(CQSPI_REG_CONFIG_CHIPSELECT_MASK
> + << CQSPI_REG_CONFIG_CHIPSELECT_LSB);
> + reg |= (chip_select & CQSPI_REG_CONFIG_CHIPSELECT_MASK)
> + << CQSPI_REG_CONFIG_CHIPSELECT_LSB;
> + writel(reg, &cadence_qspi_base->cfg);
> +
> + cadence_qspi_apb_controller_enable();
> + return;
> +}
> +
> +static void cadence_qspi_apb_delay(unsigned int ref_clk, unsigned int sclk_hz,
> + unsigned int tshsl_ns, unsigned int tsd2d_ns,
> + unsigned int tchsh_ns, unsigned int tslch_ns)
> +{
> + unsigned int ref_clk_ns;
> + unsigned int sclk_ns;
> + unsigned int tshsl, tchsh, tslch, tsd2d;
> + unsigned int reg;
> +
> + cadence_qspi_apb_controller_disable();
> +
> + /* Convert to ns. */
> + ref_clk_ns = (1000000000) / ref_clk;
> +
> + /* Convert to ns. */
> + sclk_ns = (1000000000) / sclk_hz;
> +
> + /* Plus 1 to round up 1 clock cycle. */
> + tshsl = CQSPI_CAL_DELAY(tshsl_ns, ref_clk_ns, sclk_ns) + 1;
> + tchsh = CQSPI_CAL_DELAY(tchsh_ns, ref_clk_ns, sclk_ns) + 1;
> + tslch = CQSPI_CAL_DELAY(tslch_ns, ref_clk_ns, sclk_ns) + 1;
> + tsd2d = CQSPI_CAL_DELAY(tsd2d_ns, ref_clk_ns, sclk_ns) + 1;
> +
> + reg = ((tshsl & CQSPI_REG_DELAY_TSHSL_MASK)
> + << CQSPI_REG_DELAY_TSHSL_LSB);
> + reg |= ((tchsh & CQSPI_REG_DELAY_TCHSH_MASK)
> + << CQSPI_REG_DELAY_TCHSH_LSB);
> + reg |= ((tslch & CQSPI_REG_DELAY_TSLCH_MASK)
> + << CQSPI_REG_DELAY_TSLCH_LSB);
> + reg |= ((tsd2d & CQSPI_REG_DELAY_TSD2D_MASK)
> + << CQSPI_REG_DELAY_TSD2D_LSB);
> + writel(reg, &cadence_qspi_base->delay);
> +
> + cadence_qspi_apb_controller_enable();
> + return;
> +}
> +
> +static void cadence_qspi_apb_controller_init(void)
> +{
> + unsigned reg;
> +
> + cadence_qspi_apb_controller_disable();
> +
> + /* Configure the device size and address bytes */
> + reg = readl(&cadence_qspi_base->devsz);
> + /* Clear the previous value */
> + reg &= ~(CQSPI_REG_SIZE_PAGE_MASK << CQSPI_REG_SIZE_PAGE_LSB);
> + reg &= ~(CQSPI_REG_SIZE_BLOCK_MASK << CQSPI_REG_SIZE_BLOCK_LSB);
> + reg |= (CONFIG_CQSPI_PAGE_SIZE << CQSPI_REG_SIZE_PAGE_LSB);
> + reg |= (CONFIG_CQSPI_BLOCK_SIZE << CQSPI_REG_SIZE_BLOCK_LSB);
> + writel(reg, &cadence_qspi_base->devsz);
> +
> + /* Configure the remap address register, no remap */
> + writel(0, &cadence_qspi_base->remapaddr);
> +
> + /* Disable all interrupts */
> + writel(0, &cadence_qspi_base->irqmask);
> +
> + cadence_qspi_apb_controller_enable();
> + return;
> +}
> +
> +static int cadence_qspi_apb_exec_flash_cmd(unsigned int reg)
> +{
> + unsigned int retry = CQSPI_REG_RETRY;
> +
> + /* Write the CMDCTRL without start execution. */
> + writel(reg, &cadence_qspi_base->flashcmd);
> + /* Start execute */
> + reg |= CQSPI_REG_CMDCTRL_EXECUTE_MASK;
> + writel(reg, &cadence_qspi_base->flashcmd);
> +
> + while (retry--) {
> + reg = readl(&cadence_qspi_base->flashcmd);
> + if ((reg & CQSPI_REG_CMDCTRL_INPROGRESS_MASK) == 0)
> + break;
> + udelay(1);
> + }
> +
> + if (!retry) {
> + printf("QSPI: flash command execution timeout\n");
> + return -EIO;
> + }
> +
> + /* Polling QSPI idle status. */
> + if (!cadence_qspi_wait_idle())
> + return -EIO;
> +
> + return 0;
> +}
> +
> +/* For command RDID, RDSR. */
> +static int cadence_qspi_apb_command_read(unsigned int cmdlen, const u8 *cmdbuf,
> + unsigned int rxlen, u8 *rxbuf)
> +{
> + unsigned int reg;
> + unsigned int read_len;
> + int status;
> +
> + if (!cmdlen || rxlen > CQSPI_STIG_DATA_LEN_MAX || rxbuf == NULL) {
> + printf("QSPI: Invalid input arguments cmdlen %d "
> + "rxlen %d\n", cmdlen, rxlen);
> + return -EINVAL;
> + }
> +
> + reg = cmdbuf[0] << CQSPI_REG_CMDCTRL_OPCODE_LSB;
> +
> + reg |= (0x1 << CQSPI_REG_CMDCTRL_RD_EN_LSB);
> +
> + /* 0 means 1 byte. */
> + reg |= (((rxlen - 1) & CQSPI_REG_CMDCTRL_RD_BYTES_MASK)
> + << CQSPI_REG_CMDCTRL_RD_BYTES_LSB);
> + status = cadence_qspi_apb_exec_flash_cmd(reg);
> + if (status != 0)
> + return status;
> +
> + reg = readl(&cadence_qspi_base->flashcmdrddatalo);
> +
> + /* Put the read value into rx_buf */
> + read_len = (rxlen > 4) ? 4 : rxlen;
> + memcpy(rxbuf, ®, read_len);
> + rxbuf += read_len;
> +
> + if (rxlen > 4) {
> + reg = readl(&cadence_qspi_base->flashcmdrddataup);
> +
> + read_len = rxlen - read_len;
> + memcpy(rxbuf, ®, read_len);
> + }
> + return 0;
> +}
> +
> +/* For commands: WRSR, WREN, WRDI, CHIP_ERASE, BE, etc. */
> +static int cadence_qspi_apb_command_write(unsigned int cmdlen,
> + const u8 *cmdbuf, unsigned int txlen, const u8 *txbuf)
> +{
> + unsigned int reg = 0;
> + unsigned int addr_value;
> + unsigned int wr_data;
> + unsigned int wr_len;
> +
> + if (!cmdlen || cmdlen > 5 || txlen > 8 || cmdbuf == NULL) {
> + printf("QSPI: Invalid input arguments cmdlen %d txlen %d\n",
> + cmdlen, txlen);
> + return -EINVAL;
> + }
> +
> + reg |= cmdbuf[0] << CQSPI_REG_CMDCTRL_OPCODE_LSB;
> +
> + if (cmdlen == 4 || cmdlen == 5) {
> + /* Command with address */
> + reg |= (0x1 << CQSPI_REG_CMDCTRL_ADDR_EN_LSB);
> + /* Number of bytes to write. */
> + reg |= ((cmdlen - 2) & CQSPI_REG_CMDCTRL_ADD_BYTES_MASK)
> + << CQSPI_REG_CMDCTRL_ADD_BYTES_LSB;
> + /* Get address */
> + addr_value = cadence_qspi_apb_cmd2addr(&cmdbuf[1],
> + cmdlen >= 5 ? 4 : 3);
> +
> + writel(addr_value, &cadence_qspi_base->flashcmdaddr);
> + }
> +
> + if (txlen) {
> + /* writing data = yes */
> + reg |= (0x1 << CQSPI_REG_CMDCTRL_WR_EN_LSB);
> + reg |= ((txlen - 1) & CQSPI_REG_CMDCTRL_WR_BYTES_MASK)
> + << CQSPI_REG_CMDCTRL_WR_BYTES_LSB;
> +
> + wr_len = txlen > 4 ? 4 : txlen;
> + memcpy(&wr_data, txbuf, wr_len);
> + writel(wr_data, &cadence_qspi_base->flashcmdwrdatalo);
> +
> + if (txlen > 4) {
> + txbuf += wr_len;
> + wr_len = txlen - wr_len;
> + memcpy(&wr_data, txbuf, wr_len);
> + writel(wr_data, &cadence_qspi_base->flashcmdwrdataup);
> + }
> + }
> +
> + /* Execute the command */
> + return cadence_qspi_apb_exec_flash_cmd(reg);
> +}
> +
> +/* Opcode + Address (3/4 bytes) + dummy bytes (0-4 bytes) */
> +static int cadence_qspi_apb_indirect_read_setup(unsigned int ahb_phy_addr,
> + unsigned int cmdlen, const u8 *cmdbuf)
> +{
> + unsigned int reg;
> + unsigned int rd_reg;
> + unsigned int addr_value;
> + unsigned int dummy_clk;
> + unsigned int dummy_bytes;
> + unsigned int addr_bytes;
> +
> + /*
> + * Identify addr_byte. All NOR flash device drivers are using fast read
> + * which always expecting 1 dummy byte, 1 cmd byte and 3/4 addr byte.
> + * With that, the length is in value of 5 or 6. Only FRAM chip from
> + * ramtron using normal read (which won't need dummy byte).
> + * Unlikely NOR flash using normal read due to performance issue.
> + */
> + if (cmdlen >= 5)
> + /* to cater fast read where cmd + addr + dummy */
> + addr_bytes = cmdlen - 2;
> + else
> + /* for normal read (only ramtron as of now) */
> + addr_bytes = cmdlen - 1;
> +
> + /* Setup the indirect trigger address */
> + writel((ahb_phy_addr & CQSPI_INDIRECTTRIGGER_ADDR_MASK),
> + &cadence_qspi_base->indaddrtrig);
> +
> + /* Configure SRAM partition for read. */
> + writel(CQSPI_REG_SRAM_PARTITION_RD, &cadence_qspi_base->srampart);
> +
> + /* Configure the opcode */
> + rd_reg = cmdbuf[0] << CQSPI_REG_RD_INSTR_OPCODE_LSB;
> +
> +#if (CONFIG_SPI_FLASH_QUAD == 1)
> + /* Instruction and address at DQ0, data at DQ0-3. */
> + rd_reg |= CQSPI_INST_TYPE_QUAD << CQSPI_REG_RD_INSTR_TYPE_DATA_LSB;
> +#endif
> +
> + /* Get address */
> + addr_value = cadence_qspi_apb_cmd2addr(&cmdbuf[1], addr_bytes);
> + writel(addr_value, &cadence_qspi_base->indrdstaddr);
> +
> + /* The remaining lenght is dummy bytes. */
> + dummy_bytes = cmdlen - addr_bytes - 1;
> + if (dummy_bytes) {
> +
> + if (dummy_bytes > CQSPI_DUMMY_BYTES_MAX)
> + dummy_bytes = CQSPI_DUMMY_BYTES_MAX;
> +
> + rd_reg |= (1 << CQSPI_REG_RD_INSTR_MODE_EN_LSB);
> +#if defined(CONFIG_SPL_SPI_XIP) && defined(CONFIG_SPL_BUILD)
> + writel(0x0, &cadence_qspi_base->modebit);
> +#else
> + writel(0xFF, &cadence_qspi_base->modebit);
> +#endif
> +
> + /* Convert to clock cycles. */
> + dummy_clk = dummy_bytes * CQSPI_DUMMY_CLKS_PER_BYTE;
> + /* Need to minus the mode byte (8 clocks). */
> + dummy_clk -= CQSPI_DUMMY_CLKS_PER_BYTE;
> +
> + if (dummy_clk)
> + rd_reg |= (dummy_clk & CQSPI_REG_RD_INSTR_DUMMY_MASK)
> + << CQSPI_REG_RD_INSTR_DUMMY_LSB;
> + }
> +
> + writel(rd_reg, &cadence_qspi_base->devrd);
> +
> + /* set device size */
> + reg = readl(&cadence_qspi_base->devsz);
> + reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
> + reg |= (addr_bytes - 1);
> + writel(reg, &cadence_qspi_base->devsz);
> + return 0;
> +}
> +
> +static int cadence_qspi_apb_indirect_read_execute(void *ahb_base_addr,
> + unsigned int rxlen, u8 *rxbuf)
> +{
> + unsigned int reg;
> +
> + writel(rxlen, &cadence_qspi_base->indrdcnt);
> +
> + /* Start the indirect read transfer */
> + writel(CQSPI_REG_INDIRECTRD_START_MASK,
> + &cadence_qspi_base->indrd);
> +
> + if (qspi_read_sram_fifo_poll((void *)rxbuf,
> + (const void *)ahb_base_addr, rxlen)) {
> + goto failrd;
> + }
> +
> + /* Check flash indirect controller */
> + reg = readl(&cadence_qspi_base->indrd);
> + if (!(reg & CQSPI_REG_INDIRECTRD_DONE_MASK)) {
> + reg = readl(&cadence_qspi_base->indrd);
> + printf("QSPI: indirect completion status "
> + "error with reg 0x%08x\n", reg);
> + goto failrd;
> + }
> +
> + /* Clear indirect completion status */
> + writel(CQSPI_REG_INDIRECTRD_DONE_MASK, &cadence_qspi_base->indrd);
> + return 0;
> +
> +failrd:
> + /* Cancel the indirect read */
> + writel(CQSPI_REG_INDIRECTRD_CANCEL_MASK, &cadence_qspi_base->indrd);
> + return -1;
> +}
> +
> +/* Opcode + Address (3/4 bytes) */
> +static int cadence_qspi_apb_indirect_write_setup(unsigned int ahb_phy_addr,
> + unsigned int cmdlen, const u8 *cmdbuf)
> +{
> + unsigned int reg;
> + unsigned int addr_bytes = cmdlen > 4 ? 4 : 3;
> +
> + if (cmdlen < 4 || cmdbuf == NULL) {
> + printf("QSPI: iInvalid input argument, len %d cmdbuf 0x%08x\n",
> + cmdlen, (unsigned int)cmdbuf);
> + return -EINVAL;
> + }
> + /* Setup the indirect trigger address */
> + writel((ahb_phy_addr & CQSPI_INDIRECTTRIGGER_ADDR_MASK),
> + &cadence_qspi_base->indaddrtrig);
> +
> + writel(CQSPI_REG_SRAM_PARTITION_WR,
> + &cadence_qspi_base->srampart);
> +
> + /* Configure the opcode */
> + reg = cmdbuf[0] << CQSPI_REG_WR_INSTR_OPCODE_LSB;
> + writel(reg, &cadence_qspi_base->devwr);
> +
> + /* Setup write address. */
> + reg = cadence_qspi_apb_cmd2addr(&cmdbuf[1], addr_bytes);
> + writel(reg, &cadence_qspi_base->indwrstaddr);
> +
> + reg = readl(&cadence_qspi_base->devsz);
> + reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
> + reg |= (addr_bytes - 1);
> + writel(reg, &cadence_qspi_base->devsz);
> + return 0;
> +}
> +
> +static int cadence_qspi_apb_indirect_write_execute(void *ahb_base_addr,
> + unsigned int txlen, const u8 *txbuf)
> +{
> + unsigned int reg = 0;
> + unsigned int retry;
> +
> + /* Configure the indirect read transfer bytes */
> + writel(txlen, &cadence_qspi_base->indwrcnt);
> +
> + /* Start the indirect write transfer */
> + writel(CQSPI_REG_INDIRECTWR_START_MASK, &cadence_qspi_base->indwr);
> +
> + if (qpsi_write_sram_fifo_push(ahb_base_addr,
> + (const void *)txbuf, txlen)) {
> + goto failwr;
> + }
> +
> + /* Wait until last write is completed (FIFO empty) */
> + retry = CQSPI_REG_RETRY;
> + while (retry--) {
> + reg = CQSPI_GET_WR_SRAM_LEVEL();
> + if (reg == 0)
> + break;
> +
> + udelay(1);
> + }
> + if (reg != 0) {
> + printf("QSPI: timeout for indirect write\n");
> + goto failwr;
> + }
> +
> + /* Check flash indirect controller status */
> + retry = CQSPI_REG_RETRY;
> + while (retry--) {
> + reg = readl(&cadence_qspi_base->indwr);
> + if (reg & CQSPI_REG_INDIRECTWR_DONE_MASK)
> + break;
> + udelay(1);
> + }
> + if (!(reg & CQSPI_REG_INDIRECTWR_DONE_MASK)) {
> + printf("QSPI: indirect completion "
> + "status error with reg 0x%08x\n", reg);
> + goto failwr;
> + }
> +
> + /* Clear indirect completion status */
> + writel(CQSPI_REG_INDIRECTWR_DONE_MASK, &cadence_qspi_base->indwr);
> + return 0;
> +
> +failwr:
> + /* Cancel the indirect write */
> + writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK, &cadence_qspi_base->indwr);
> + return -1;
> +}
> +
> +static void cadence_qspi_apb_enter_xip(char xip_dummy)
> +{
> + unsigned int reg;
> +
> + /* enter XiP mode immediately and enable direct mode */
> + reg = readl(&cadence_qspi_base->cfg);
> + reg |= CQSPI_REG_CONFIG_ENABLE_MASK;
> + reg |= CQSPI_REG_CONFIG_DIRECT_MASK;
> + reg |= CQSPI_REG_CONFIG_XIP_IMM_MASK;
> + writel(reg, &cadence_qspi_base->cfg);
> +
> + /* keep the XiP mode */
> + writel(xip_dummy, &cadence_qspi_base->modebit);
> +
> + /* Enable mode bit at devrd */
> + reg = readl(&cadence_qspi_base->devrd);
> + reg |= (1 << CQSPI_REG_RD_INSTR_MODE_EN_LSB);
> + writel(reg, &cadence_qspi_base->devrd);
> +}
> +
> +void spi_set_speed(struct spi_slave *slave, uint hz)
> +{
> + cadence_qspi_apb_config_baudrate_div(CONFIG_CQSPI_REF_CLK, hz);
> +
> + /* Reconfigure delay timing if speed is changed. */
> + cadence_qspi_apb_delay(CONFIG_CQSPI_REF_CLK, hz,
> + CONFIG_CQSPI_TSHSL_NS, CONFIG_CQSPI_TSD2D_NS,
> + CONFIG_CQSPI_TCHSH_NS, CONFIG_CQSPI_TSLCH_NS);
> + return;
> +}
> +
> +/* calibration sequence to determine the read data capture delay register */
> +int spi_calibration(struct spi_slave *slave)
> +{
> + struct cadence_qspi_slave *cadence_qspi = to_cadence_qspi_slave(slave);
> + u8 opcode_rdid = 0x9F;
> + unsigned int idcode = 0, temp = 0;
> + int err = 0, i, range_lo = -1, range_hi = -1;
> +
> + /* start with slowest clock (1 MHz) */
> + spi_set_speed(slave, 1000000);
> +
> + /* configure the read data capture delay register to 0 */
> + cadence_qspi_apb_readdata_capture(1, 0);
> +
> + /* Enable QSPI */
> + cadence_qspi_apb_controller_enable();
> +
> + /* read the ID which will be our golden value */
> + err = cadence_qspi_apb_command_read(1, &opcode_rdid,
> + 3, (u8 *)&idcode);
> + if (err) {
> + puts("SF: Calibration failed (read)\n");
> + return err;
> + }
> +
> + /* use back the intended clock and find low range */
> + spi_set_speed(slave, cadence_qspi->max_hz);
> + for (i = 0; i < CQSPI_READ_CAPTURE_MAX_DELAY; i++) {
> + /* Disable QSPI */
> + cadence_qspi_apb_controller_disable();
> +
> + /* reconfigure the read data capture delay register */
> + cadence_qspi_apb_readdata_capture(1, i);
> +
> + /* Enable back QSPI */
> + cadence_qspi_apb_controller_enable();
> +
> + /* issue a RDID to get the ID value */
> + err = cadence_qspi_apb_command_read(1, &opcode_rdid,
> + 3, (u8 *)&temp);
> + if (err) {
> + puts("SF: Calibration failed (read)\n");
> + return err;
> + }
> +
> + /* search for range lo */
> + if (range_lo == -1 && temp == idcode) {
> + range_lo = i;
> + continue;
> + }
> +
> + /* search for range hi */
> + if (range_lo != -1 && temp != idcode) {
> + range_hi = i - 1;
> + break;
> + }
> + range_hi = i;
> + }
> +
> + if (range_lo == -1) {
> + puts("SF: Calibration failed (low range)\n");
> + return err;
> + }
> +
> + /* Disable QSPI for subsequent initialization */
> + cadence_qspi_apb_controller_disable();
> +
> + /* configure the final value for read data capture delay register */
> + cadence_qspi_apb_readdata_capture(1, (range_hi + range_lo) / 2);
> + printf("SF: Read data capture delay calibrated to %i (%i - %i)\n",
> + (range_hi + range_lo) / 2, range_lo, range_hi);
> +
> + /* just to ensure we do once only when speed or chip select change */
> + qspi_calibrated_hz = cadence_qspi->max_hz;
> + qspi_calibrated_cs = slave->cs;
> + return 0;
> +}
> +
> +int spi_cs_is_valid(unsigned int bus, unsigned int cs)
> +{
> +#if (CONFIG_CQSPI_DECODER == 1)
> + if (((cs >= 0) && (cs < CQSPI_DECODER_MAX_CS)) && ((bus >= 0) &&
> + (bus < CQSPI_DECODER_MAX_CS))) {
> + return 1;
> + }
> +#else
> + if (((cs >= 0) && (cs < CQSPI_NO_DECODER_MAX_CS)) &&
> + ((bus >= 0) && (bus < CQSPI_NO_DECODER_MAX_CS))) {
> + return 1;
> + }
> +#endif
> + printf("QSPI: Invalid bus or cs. Bus %d cs %d\n", bus, cs);
> + return 0;
> +}
> +
> +void spi_cs_activate(struct spi_slave *slave)
> +{
> + return;
> +}
> +
> +void spi_cs_deactivate(struct spi_slave *slave)
> +{
> + return;
> +}
> +
> +void spi_init(void)
> +{
> + cadence_qspi_apb_controller_init();
> + qspi_is_init = 1;
> + return;
> +}
> +
> +struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
> + unsigned int max_hz, unsigned int mode)
> +{
> + struct cadence_qspi_slave *cadence_qspi;
> +
> + debug("%s: bus %d cs %d max_hz %dMHz mode %d\n", __func__,
> + bus, cs, max_hz/1000000, mode);
> +
> + if (!spi_cs_is_valid(bus, cs))
> + return NULL;
> +
> + cadence_qspi = malloc(sizeof(struct cadence_qspi_slave));
> + if (!cadence_qspi) {
> + printf("QSPI: Can't allocate struct cadence_qspi_slave. "
> + "Bus %d cs %d\n", bus, cs);
> + return NULL;
> + }
> +
> + cadence_qspi->slave.bus = bus;
> + cadence_qspi->slave.cs = cs;
> + cadence_qspi->mode = mode;
> + cadence_qspi->max_hz = max_hz;
> + cadence_qspi->regbase = (void *)QSPI_BASE;
> + cadence_qspi->ahbbase = (void *)QSPI_AHB_BASE;
> +
> + if (!qspi_is_init)
> + spi_init();
> +
> + return &cadence_qspi->slave;
> +}
> +
> +void spi_free_slave(struct spi_slave *slave)
> +{
> + struct cadence_qspi_slave *cadence_qspi = to_cadence_qspi_slave(slave);
> + free(cadence_qspi);
> + return;
> +}
> +
> +int spi_claim_bus(struct spi_slave *slave)
> +{
> + struct cadence_qspi_slave *cadence_qspi = to_cadence_qspi_slave(slave);
> + unsigned int clk_pol = (cadence_qspi->mode & SPI_CPOL) ? 1 : 0;
> + unsigned int clk_pha = (cadence_qspi->mode & SPI_CPHA) ? 1 : 0;
> + int err = 0;
> +
> + debug("%s: bus:%i cs:%i\n", __func__, slave->bus, slave->cs);
> +
> + /* Disable QSPI */
> + cadence_qspi_apb_controller_disable();
> +
> + /* Set Chip select */
> + cadence_qspi_apb_chipselect(slave->cs, CONFIG_CQSPI_DECODER);
> +
> + /* Set SPI mode */
> + cadence_qspi_apb_set_clk_mode(clk_pol, clk_pha);
> +
> + /* Set clock speed */
> + spi_set_speed(slave, cadence_qspi->max_hz);
> +
> + /* calibration required for different SCLK speed or chip select */
> + if (qspi_calibrated_hz != cadence_qspi->max_hz ||
> + qspi_calibrated_cs != slave->cs) {
> + err = spi_calibration(slave);
> + if (err)
> + return err;
> + }
> +
> + /* Enable QSPI */
> + cadence_qspi_apb_controller_enable();
> +
> + return 0;
> +}
> +
> +void spi_release_bus(struct spi_slave *slave)
> +{
> + return;
> +}
> +
> +int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *data_out,
> + void *data_in, unsigned long flags)
> +{
> + struct cadence_qspi_slave *cadence_qspi = to_cadence_qspi_slave(slave);
> + void *ahbbase = cadence_qspi->ahbbase;
> + u8 *cmd_buf = cadence_qspi->cmd_buf;
> + size_t data_bytes;
> + int err = 0;
> + u32 mode = CQSPI_STIG_WRITE;
> +
> + if (flags & SPI_XFER_BEGIN) {
> + /* copy command to local buffer */
> + cadence_qspi->cmd_len = bitlen / 8;
> + memcpy(cmd_buf, data_out, cadence_qspi->cmd_len);
> + }
> +
> + if (flags == (SPI_XFER_BEGIN | SPI_XFER_END)) {
> + /* if start and end bit are set, the data bytes is 0. */
> + data_bytes = 0;
> + } else {
> + data_bytes = bitlen / 8;
> + }
> +
> + if ((flags & SPI_XFER_END) || (flags == 0)) {
> + if (cadence_qspi->cmd_len == 0) {
> + printf("QSPI: Error, command is empty.\n");
> + return -1;
> + }
> +
> + if (data_in && data_bytes) {
> + /* read */
> + /* Use STIG if no address. */
> + if (!CQSPI_IS_ADDR(cadence_qspi->cmd_len))
> + mode = CQSPI_STIG_READ;
> + else
> + mode = CQSPI_INDIRECT_READ;
> + } else if (data_out && !(flags & SPI_XFER_BEGIN)) {
> + /* write */
> + if (!CQSPI_IS_ADDR(cadence_qspi->cmd_len))
> + mode = CQSPI_STIG_WRITE;
> + else
> + mode = CQSPI_INDIRECT_WRITE;
> + }
> +
> + switch (mode) {
> + case CQSPI_STIG_READ:
> + err = cadence_qspi_apb_command_read(
> + cadence_qspi->cmd_len, cmd_buf,
> + data_bytes, data_in);
> +
> + break;
> + case CQSPI_STIG_WRITE:
> + err = cadence_qspi_apb_command_write(
> + cadence_qspi->cmd_len, cmd_buf,
> + data_bytes, data_out);
> + break;
> + case CQSPI_INDIRECT_READ:
> + err = cadence_qspi_apb_indirect_read_setup(
> + QSPI_AHB_BASE,
> + cadence_qspi->cmd_len, cmd_buf);
> + if (!err) {
> + err = cadence_qspi_apb_indirect_read_execute
> + (ahbbase, data_bytes, data_in);
> + }
> + break;
> + case CQSPI_INDIRECT_WRITE:
> + err = cadence_qspi_apb_indirect_write_setup
> + (QSPI_AHB_BASE,
> + cadence_qspi->cmd_len, cmd_buf);
> + if (!err) {
> + err = cadence_qspi_apb_indirect_write_execute
> + (ahbbase, data_bytes, data_out);
> + }
> + break;
> + default:
> + err = -1;
> + break;
> + }
Most of the code function in this driver is derived based on the mode
- like commands.
Better to write common and optimized code which can handle all together.
Once ie done! yes we can add slave->option(is coming) to configure the driver as
single, double and quad ops.
> +
> + if (flags & SPI_XFER_END) {
> + /* clear command buffer */
> + memset(cmd_buf, 0, sizeof(cadence_qspi->cmd_buf));
> + cadence_qspi->cmd_len = 0;
> + }
> + }
> + return err;
> +}
> +
> +void spi_enter_xip(struct spi_slave *slave, char xip_dummy)
> +{
> + /* Enter XiP */
> + cadence_qspi_apb_enter_xip(xip_dummy);
> + return;
> +}
> +
> +
> diff --git a/drivers/spi/cadence_qspi.h b/drivers/spi/cadence_qspi.h
> new file mode 100644
> index 0000000..1466735
> --- /dev/null
> +++ b/drivers/spi/cadence_qspi.h
> @@ -0,0 +1,170 @@
> +/*
> + * (C) Copyright 2014 Altera Corporation <www.altera.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __CADENCE_QSPI_H__
> +#define __CADENCE_QSPI_H__
> +
> +#define QSPI_BASE (CONFIG_CQSPI_BASE)
> +#define QSPI_AHB_BASE (CONFIG_CQSPI_AHB_BASE)
> +#define CQSPI_IS_ADDR(cmd_len) (cmd_len > 1 ? 1 : 0)
> +
> +struct cadence_qspi_slave {
> + struct spi_slave slave;
> + unsigned int mode;
> + unsigned int max_hz;
> + void *regbase;
> + void *ahbbase;
> + size_t cmd_len;
> + u8 cmd_buf[32];
> + size_t data_len;
> +};
> +
> +struct cadence_qspi {
> + u32 cfg;
> + u32 devrd;
> + u32 devwr;
> + u32 delay;
> + u32 rddatacap;
> + u32 devsz;
> + u32 srampart;
> + u32 indaddrtrig;
> + u32 dmaper;
> + u32 remapaddr;
> + u32 modebit;
> + u32 sramfill;
> + u32 txthresh;
> + u32 rxthresh;
> + u32 _pad_0x38_0x3f[2];
> + u32 irqstat;
> + u32 irqmask;
> + u32 _pad_0x48_0x4f[2];
> + u32 lowwrprot;
> + u32 uppwrprot;
> + u32 wrprot;
> + u32 _pad_0x5c_0x5f;
> + u32 indrd;
> + u32 indrdwater;
> + u32 indrdstaddr;
> + u32 indrdcnt;
> + u32 indwr;
> + u32 indwrwater;
> + u32 indwrstaddr;
> + u32 indwrcnt;
> + u32 _pad_0x80_0x8f[4];
> + u32 flashcmd;
> + u32 flashcmdaddr;
> + u32 _pad_0x98_0x9f[2];
> + u32 flashcmdrddatalo;
> + u32 flashcmdrddataup;
> + u32 flashcmdwrdatalo;
> + u32 flashcmdwrdataup;
> + u32 _pad_0xb0_0xfb[19];
> + u32 moduleid;
> +};
> +
> +/* Controller's configuration and status register */
> +#define CQSPI_REG_CONFIG_CLK_POL_LSB 1
> +#define CQSPI_REG_CONFIG_CLK_PHA_LSB 2
> +#define CQSPI_REG_CONFIG_ENABLE_MASK (1 << 0)
> +#define CQSPI_REG_CONFIG_DIRECT_MASK (1 << 7)
> +#define CQSPI_REG_CONFIG_DECODE_MASK (1 << 9)
> +#define CQSPI_REG_CONFIG_XIP_IMM_MASK (1 << 18)
> +#define CQSPI_REG_CONFIG_CHIPSELECT_LSB 10
> +#define CQSPI_REG_CONFIG_BAUD_LSB 19
> +#define CQSPI_REG_CONFIG_IDLE_LSB 31
> +#define CQSPI_REG_CONFIG_CHIPSELECT_MASK 0xF
> +#define CQSPI_REG_CONFIG_BAUD_MASK 0xF
> +#define CQSPI_REG_RD_INSTR_OPCODE_LSB 0
> +#define CQSPI_REG_RD_INSTR_TYPE_INSTR_LSB 8
> +#define CQSPI_REG_RD_INSTR_TYPE_ADDR_LSB 12
> +#define CQSPI_REG_RD_INSTR_TYPE_DATA_LSB 16
> +#define CQSPI_REG_RD_INSTR_MODE_EN_LSB 20
> +#define CQSPI_REG_RD_INSTR_DUMMY_LSB 24
> +#define CQSPI_REG_RD_INSTR_TYPE_INSTR_MASK 0x3
> +#define CQSPI_REG_RD_INSTR_TYPE_ADDR_MASK 0x3
> +#define CQSPI_REG_RD_INSTR_TYPE_DATA_MASK 0x3
> +#define CQSPI_REG_RD_INSTR_DUMMY_MASK 0x1F
> +#define CQSPI_REG_WR_INSTR_OPCODE_LSB 0
> +#define CQSPI_REG_DELAY_TSLCH_LSB 0
> +#define CQSPI_REG_DELAY_TCHSH_LSB 8
> +#define CQSPI_REG_DELAY_TSD2D_LSB 16
> +#define CQSPI_REG_DELAY_TSHSL_LSB 24
> +#define CQSPI_REG_DELAY_TSLCH_MASK 0xFF
> +#define CQSPI_REG_DELAY_TCHSH_MASK 0xFF
> +#define CQSPI_REG_DELAY_TSD2D_MASK 0xFF
> +#define CQSPI_REG_DELAY_TSHSL_MASK 0xFF
> +#define CQSPI_REG_RD_DATA_CAPTURE_BYPASS_LSB 0
> +#define CQSPI_REG_RD_DATA_CAPTURE_DELAY_LSB 1
> +#define CQSPI_REG_RD_DATA_CAPTURE_DELAY_MASK 0xF
> +#define CQSPI_REG_SIZE_ADDRESS_LSB 0
> +#define CQSPI_REG_SIZE_PAGE_LSB 4
> +#define CQSPI_REG_SIZE_BLOCK_LSB 16
> +#define CQSPI_REG_SIZE_ADDRESS_MASK 0xF
> +#define CQSPI_REG_SIZE_PAGE_MASK 0xFFF
> +#define CQSPI_REG_SIZE_BLOCK_MASK 0x3F
> +#define CQSPI_REG_SRAMLEVEL_RD_LSB 0
> +#define CQSPI_REG_SRAMLEVEL_WR_LSB 16
> +#define CQSPI_REG_SRAMLEVEL_RD_MASK 0xFFFF
> +#define CQSPI_REG_SRAMLEVEL_WR_MASK 0xFFFF
> +#define CQSPI_REG_INDIRECTRD_START_MASK (1 << 0)
> +#define CQSPI_REG_INDIRECTRD_CANCEL_MASK (1 << 1)
> +#define CQSPI_REG_INDIRECTRD_INPROGRESS_MASK (1 << 2)
> +#define CQSPI_REG_INDIRECTRD_DONE_MASK (1 << 5)
> +#define CQSPI_REG_CMDCTRL_EXECUTE_MASK (1 << 0)
> +#define CQSPI_REG_CMDCTRL_INPROGRESS_MASK (1 << 1)
> +#define CQSPI_REG_CMDCTRL_DUMMY_LSB 7
> +#define CQSPI_REG_CMDCTRL_WR_BYTES_LSB 12
> +#define CQSPI_REG_CMDCTRL_WR_EN_LSB 15
> +#define CQSPI_REG_CMDCTRL_ADD_BYTES_LSB 16
> +#define CQSPI_REG_CMDCTRL_ADDR_EN_LSB 19
> +#define CQSPI_REG_CMDCTRL_RD_BYTES_LSB 20
> +#define CQSPI_REG_CMDCTRL_RD_EN_LSB 23
> +#define CQSPI_REG_CMDCTRL_OPCODE_LSB 24
> +#define CQSPI_REG_CMDCTRL_DUMMY_MASK 0x1F
> +#define CQSPI_REG_CMDCTRL_WR_BYTES_MASK 0x7
> +#define CQSPI_REG_CMDCTRL_ADD_BYTES_MASK 0x3
> +#define CQSPI_REG_CMDCTRL_RD_BYTES_MASK 0x7
> +#define CQSPI_REG_CMDCTRL_OPCODE_MASK 0xFF
> +#define CQSPI_REG_INDIRECTWR_START_MASK (1 << 0)
> +#define CQSPI_REG_INDIRECTWR_CANCEL_MASK (1 << 1)
> +#define CQSPI_REG_INDIRECTWR_INPROGRESS_MASK (1 << 2)
> +#define CQSPI_REG_INDIRECTWR_DONE_MASK (1 << 5)
> +
> +/* Transfer type */
> +#define CQSPI_STIG_READ 0
> +#define CQSPI_STIG_WRITE 1
> +#define CQSPI_INDIRECT_READ 2
> +#define CQSPI_INDIRECT_WRITE 3
> +
> +/* Transfer mode */
> +#define CQSPI_INST_TYPE_SINGLE (0)
> +#define CQSPI_INST_TYPE_DUAL (1)
> +#define CQSPI_INST_TYPE_QUAD (2)
> +
> +/* controller operation setting */
> +#define CQSPI_NO_DECODER_MAX_CS (4)
> +#define CQSPI_DECODER_MAX_CS (16)
> +#define CQSPI_READ_CAPTURE_MAX_DELAY (16)
> +#define CQSPI_REG_POLL_US (1)
> +#define CQSPI_REG_RETRY (10000)
> +#define CQSPI_POLL_IDLE_RETRY (3)
> +#define CQSPI_FIFO_WIDTH (4)
> +#define CQSPI_STIG_DATA_LEN_MAX (8)
> +#define CQSPI_INDIRECTTRIGGER_ADDR_MASK (0xFFFFF)
> +#define CQSPI_DUMMY_CLKS_PER_BYTE (8)
> +#define CQSPI_DUMMY_BYTES_MAX (4)
> +
> +/* Controller sram size in word */
> +#define CQSPI_REG_SRAM_SIZE_WORD (128)
> +#define CQSPI_REG_SRAM_RESV_WORDS (2)
> +#define CQSPI_REG_SRAM_PARTITION_WR (1)
> +#define CQSPI_REG_SRAM_PARTITION_RD \
> + (CQSPI_REG_SRAM_SIZE_WORD - CQSPI_REG_SRAM_RESV_WORDS)
> +#define CQSPI_REG_SRAM_THRESHOLD_WORDS (50)
> +#define CQSPI_REG_SRAM_FILL_THRESHOLD \
> + ((CQSPI_REG_SRAM_SIZE_WORD / 2) * CQSPI_FIFO_WIDTH)
> +
> +#endif /* __CADENCE_QSPI_H__ */
> --
> 1.7.9.5
>
>
--
Thanks,
Jagan.
More information about the U-Boot
mailing list