[U-Boot] [PATCH v3 1/2] wandboard: add Future Eletronics 7" WVGA LCD extension board
Stefano Babic
sbabic at denx.de
Mon May 5 15:11:58 CEST 2014
Hi Otavio,
On 02/05/2014 00:02, Otavio Salvador wrote:
> This adds support for the 7" WVGA produced by Future Eletronics and
> make it dynamically detect if it is connected or not based on the
> touchscreen controller.
>
> Signed-off-by: Otavio Salvador <otavio at ossystems.com.br>
> ---
>
> Changes in v3:
> - Drop LVDS related code (unused)
>
> Changes in v2:
> - Drop LDB related code (unused)
>
> board/wandboard/wandboard.c | 147 ++++++++++++++++++++++++++++++++++++--------
> include/configs/wandboard.h | 7 +++
> 2 files changed, 128 insertions(+), 26 deletions(-)
>
> diff --git a/board/wandboard/wandboard.c b/board/wandboard/wandboard.c
> index f1951dc..311a442 100644
> --- a/board/wandboard/wandboard.c
> +++ b/board/wandboard/wandboard.c
> @@ -1,5 +1,6 @@
> /*
> * Copyright (C) 2013 Freescale Semiconductor, Inc.
> + * Copyright (C) 2014 O.S. Systems Software LTDA.
> *
> * Author: Fabio Estevam <fabio.estevam at freescale.com>
> *
> @@ -15,18 +16,19 @@
> #include <asm/arch/sys_proto.h>
> #include <asm/gpio.h>
> #include <asm/imx-common/iomux-v3.h>
> +#include <asm/imx-common/mxc_i2c.h>
> #include <asm/imx-common/boot_mode.h>
> +#include <asm/imx-common/video.h>
> #include <asm/io.h>
> #include <linux/sizes.h>
> #include <common.h>
> #include <fsl_esdhc.h>
> -#include <ipu_pixfmt.h>
> #include <mmc.h>
> #include <miiphy.h>
> #include <netdev.h>
> -#include <linux/fb.h>
> #include <phy.h>
> #include <input.h>
> +#include <i2c.h>
>
> DECLARE_GLOBAL_DATA_PTR;
>
> @@ -41,6 +43,10 @@ DECLARE_GLOBAL_DATA_PTR;
> #define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
> PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
>
> +#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
> + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
> + PAD_CTL_ODE | PAD_CTL_SRE_FAST)
> +
> #define USDHC1_CD_GPIO IMX_GPIO_NR(1, 2)
> #define USDHC3_CD_GPIO IMX_GPIO_NR(3, 9)
> #define ETH_PHY_RESET IMX_GPIO_NR(3, 29)
> @@ -210,41 +216,124 @@ int board_phy_config(struct phy_device *phydev)
> }
>
> #if defined(CONFIG_VIDEO_IPUV3)
> -static struct fb_videomode const hdmi = {
> - .name = "HDMI",
> - .refresh = 60,
> - .xres = 1024,
> - .yres = 768,
> - .pixclock = 15385,
> - .left_margin = 220,
> - .right_margin = 40,
> - .upper_margin = 21,
> - .lower_margin = 7,
> - .hsync_len = 60,
> - .vsync_len = 10,
> - .sync = FB_SYNC_EXT,
> - .vmode = FB_VMODE_NONINTERLACED
> +struct i2c_pads_info i2c2_pad_info = {
> + .scl = {
> + .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL
> + | MUX_PAD_CTRL(I2C_PAD_CTRL),
> + .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12
> + | MUX_PAD_CTRL(I2C_PAD_CTRL),
> + .gp = IMX_GPIO_NR(4, 12)
> + },
> + .sda = {
> + .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA
> + | MUX_PAD_CTRL(I2C_PAD_CTRL),
> + .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13
> + | MUX_PAD_CTRL(I2C_PAD_CTRL),
> + .gp = IMX_GPIO_NR(4, 13)
> + }
> };
>
> -int board_video_skip(void)
> -{
> - int ret;
> +static iomux_v3_cfg_t const fwadapt_7wvga_pads[] = {
> + MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK,
> + MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02, /* HSync */
> + MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03, /* VSync */
> + MX6_PAD_DI0_PIN4__IPU1_DI0_PIN04
> + | MUX_PAD_CTRL(PAD_CTL_DSE_120ohm), /* Contrast */
> + MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15, /* DISP0_DRDY */
> +
> + MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00,
> + MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01,
> + MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02,
> + MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03,
> + MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04,
> + MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05,
> + MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06,
> + MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07,
> + MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08,
> + MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09,
> + MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10,
> + MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11,
> + MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12,
> + MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13,
> + MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14,
> + MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15,
> + MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16,
> + MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17,
> +
> + MX6_PAD_SD4_DAT2__GPIO2_IO10
> + | MUX_PAD_CTRL(NO_PAD_CTRL), /* DISP0_BKLEN */
> + MX6_PAD_SD4_DAT3__GPIO2_IO11
> + | MUX_PAD_CTRL(NO_PAD_CTRL), /* DISP0_VDDEN */
> +};
>
> - ret = ipuv3_fb_init(&hdmi, 0, IPU_PIX_FMT_RGB24);
> +static void do_enable_hdmi(struct display_info_t const *dev)
> +{
> + imx_enable_hdmi_phy();
> +}
>
> - if (ret) {
> - printf("HDMI cannot be configured: %d\n", ret);
> - return ret;
> - }
> +static int detect_i2c(struct display_info_t const *dev)
> +{
> + return (0 == i2c_set_bus_num(dev->bus)) &&
> + (0 == i2c_probe(dev->addr));
> +}
>
> - imx_enable_hdmi_phy();
> +static void enable_fwadapt_7wvga(struct display_info_t const *dev)
> +{
> + imx_iomux_v3_setup_multiple_pads(
> + fwadapt_7wvga_pads,
> + ARRAY_SIZE(fwadapt_7wvga_pads));
>
> - return ret;
> + gpio_direction_output(IMX_GPIO_NR(2, 10), 1);
> + gpio_direction_output(IMX_GPIO_NR(2, 11), 1);
> }
>
> +struct display_info_t const displays[] = {{
> + .bus = -1,
> + .addr = 0,
> + .pixfmt = IPU_PIX_FMT_RGB24,
> + .detect = detect_hdmi,
> + .enable = do_enable_hdmi,
> + .mode = {
> + .name = "HDMI",
> + .refresh = 60,
> + .xres = 1024,
> + .yres = 768,
> + .pixclock = 15385,
> + .left_margin = 220,
> + .right_margin = 40,
> + .upper_margin = 21,
> + .lower_margin = 7,
> + .hsync_len = 60,
> + .vsync_len = 10,
> + .sync = FB_SYNC_EXT,
> + .vmode = FB_VMODE_NONINTERLACED
> +} }, {
> + .bus = 1,
> + .addr = 0x10,
> + .pixfmt = IPU_PIX_FMT_RGB666,
> + .detect = detect_i2c,
> + .enable = enable_fwadapt_7wvga,
> + .mode = {
> + .name = "FWBADAPT-LCD-F07A-0102",
> + .refresh = 60,
> + .xres = 800,
> + .yres = 480,
> + .pixclock = 33260,
> + .left_margin = 128,
> + .right_margin = 128,
> + .upper_margin = 22,
> + .lower_margin = 22,
> + .hsync_len = 1,
> + .vsync_len = 1,
> + .sync = 0,
> + .vmode = FB_VMODE_NONINTERLACED
> +} } };
> +size_t display_count = ARRAY_SIZE(displays);
> +
> static void setup_display(void)
> {
> struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
> + struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
> int reg;
>
> enable_ipu_clock();
> @@ -254,6 +343,10 @@ static void setup_display(void)
> reg |= (CHSCCDR_CLK_SEL_LDB_DI0
> << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
> writel(reg, &mxc_ccm->chsccdr);
> +
> + /* Disable LCD backlight */
> + imx_iomux_v3_setup_pad(MX6_PAD_DI0_PIN4__GPIO4_IO20);
> + gpio_direction_input(IMX_GPIO_NR(4, 20));
> }
> #endif /* CONFIG_VIDEO_IPUV3 */
>
> @@ -305,6 +398,8 @@ int board_init(void)
> /* address of boot parameters */
> gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
>
> + setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c2_pad_info);
> +
> return 0;
> }
>
> diff --git a/include/configs/wandboard.h b/include/configs/wandboard.h
> index a49544f..6defc00 100644
> --- a/include/configs/wandboard.h
> +++ b/include/configs/wandboard.h
> @@ -58,6 +58,12 @@
> #define CONFIG_LOADADDR 0x12000000
> #define CONFIG_SYS_TEXT_BASE 0x17800000
>
> +/* I2C Configs */
> +#define CONFIG_CMD_I2C
> +#define CONFIG_SYS_I2C
> +#define CONFIG_SYS_I2C_MXC
> +#define CONFIG_SYS_I2C_SPEED 100000
> +
> /* MMC Configuration */
> #define CONFIG_FSL_ESDHC
> #define CONFIG_FSL_USDHC
> @@ -116,6 +122,7 @@
> #define CONFIG_VIDEO_BMP_LOGO
> #define CONFIG_IPUV3_CLK 260000000
> #define CONFIG_IMX_HDMI
> +#define CONFIG_IMX_VIDEO_SKIP
>
> #if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
> #define CONFIG_DEFAULT_FDT_FILE "imx6dl-wandboard.dtb"
>
Acked-by: Stefano Babic <sbabic at denx.de>
Put in my list for merging.
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
More information about the U-Boot
mailing list