[U-Boot] [RFC PATCH v2 13/13] tegra: Convert tegra GPIO driver to use driver model

Simon Glass sjg at chromium.org
Fri May 9 19:28:28 CEST 2014


This is an implementation of GPIOs for Tegra that uses driver model. It has
been tested on trimslice and also using the new iotrace feature.

The implementation uses a top-level GPIO device (which has no actual GPIOS).
Under this all the banks are created as separate GPIO devices.

The GPIOs are named as per the Tegra datasheet/header files: A0..A7, B0..B7,
..., Z0..Z7, AA0..AA7, etc.

Since driver model is not yet available before relocation, or in SPL, a
special function is provided for seaboard's SPL code.

This series is marked RFC since the Tegra driver may need further discussion.
Signed-off-by: Simon Glass <sjg at chromium.org>
---

Changes in v3:
- Move dm command enable to previous patch
- Use gpio number for the internal helper functions

Changes in v2:
- Split out driver model changes into separate patches
- Correct bugs found during testing

 arch/arm/include/asm/arch-tegra/gpio.h |  14 +-
 board/nvidia/seaboard/seaboard.c       |   2 +-
 drivers/gpio/tegra_gpio.c              | 313 +++++++++++++++++++++++++++------
 include/configs/tegra-common.h         |   1 +
 4 files changed, 266 insertions(+), 64 deletions(-)

diff --git a/arch/arm/include/asm/arch-tegra/gpio.h b/arch/arm/include/asm/arch-tegra/gpio.h
index d97190d..80e4a73 100644
--- a/arch/arm/include/asm/arch-tegra/gpio.h
+++ b/arch/arm/include/asm/arch-tegra/gpio.h
@@ -6,6 +6,8 @@
 #ifndef _TEGRA_GPIO_H_
 #define _TEGRA_GPIO_H_
 
+#define TEGRA_GPIOS_PER_PORT	8
+#define TEGRA_PORTS_PER_BANK	4
 #define MAX_NUM_GPIOS           (TEGRA_GPIO_PORTS * TEGRA_GPIO_BANKS * 8)
 #define GPIO_NAME_SIZE		20	/* gpio_request max label len */
 
@@ -14,11 +16,13 @@
 #define GPIO_FULLPORT(x)	((x) >> 3)
 #define GPIO_BIT(x)		((x) & 0x7)
 
-/*
- * Tegra-specific GPIO API
+/**
+ * tegra_spl_gpio_direction_output() - set the output value of a GPIO
+ *
+ * This function is only used from SPL on seaboard, which needs to enable a
+ * GPIO to get the UART running. It could be done in U-Boot rather than SPL,
+ * but for now, this gets it working
  */
+int tegra_spl_gpio_direction_output(int gpio, int value);
 
-void gpio_info(void);
-
-#define gpio_status()	gpio_info()
 #endif	/* TEGRA_GPIO_H_ */
diff --git a/board/nvidia/seaboard/seaboard.c b/board/nvidia/seaboard/seaboard.c
index ef4e481..e27efcd 100644
--- a/board/nvidia/seaboard/seaboard.c
+++ b/board/nvidia/seaboard/seaboard.c
@@ -22,7 +22,7 @@ void gpio_early_init_uart(void)
 #ifndef CONFIG_SPL_BUILD
 	gpio_request(GPIO_PI3, NULL);
 #endif
-	gpio_direction_output(GPIO_PI3, 0);
+	tegra_spl_gpio_direction_output(GPIO_PI3, 0);
 }
 #endif
 
diff --git a/drivers/gpio/tegra_gpio.c b/drivers/gpio/tegra_gpio.c
index 82b30d5..f03d4ed 100644
--- a/drivers/gpio/tegra_gpio.c
+++ b/drivers/gpio/tegra_gpio.c
@@ -12,10 +12,17 @@
  */
 
 #include <common.h>
+#include <dm.h>
+#include <malloc.h>
+#include <errno.h>
+#include <fdtdec.h>
 #include <asm/io.h>
 #include <asm/bitops.h>
 #include <asm/arch/tegra.h>
 #include <asm/gpio.h>
+#include <dm/device-internal.h>
+
+DECLARE_GLOBAL_DATA_PTR;
 
 enum {
 	TEGRA_CMD_INFO,
@@ -24,14 +31,18 @@ enum {
 	TEGRA_CMD_INPUT,
 };
 
-static struct gpio_names {
-	char name[GPIO_NAME_SIZE];
-} gpio_names[MAX_NUM_GPIOS];
+struct tegra_gpio_platdata {
+	struct gpio_ctlr_bank *bank;
+	const char *port_name;	/* Name of port, e.g. "B" */
+	int base_port;		/* Port number for this port (0, 1,.., n-1) */
+};
 
-static char *get_name(int i)
-{
-	return *gpio_names[i].name ? gpio_names[i].name : "UNKNOWN";
-}
+/* Information about each port at run-time */
+struct tegra_port_info {
+	char label[TEGRA_GPIOS_PER_PORT][GPIO_NAME_SIZE];
+	struct gpio_ctlr_bank *bank;
+	int base_port;		/* Port number for this port (0, 1,.., n-1) */
+};
 
 /* Return config of pin 'gpio' as GPIO (1) or SFPIO (0) */
 static int get_config(unsigned gpio)
@@ -121,38 +132,71 @@ static void set_level(unsigned gpio, int high)
 	writel(u, &bank->gpio_out[GPIO_PORT(gpio)]);
 }
 
+static int check_reserved(struct device *dev, unsigned offset,
+			  const char *func)
+{
+	struct tegra_port_info *state = dev_get_priv(dev);
+	struct gpio_dev_priv *uc_priv = dev->uclass_priv;
+
+	if (!*state->label[offset]) {
+		printf("tegra_gpio: %s: error: gpio %s%d not reserved\n",
+		       func, uc_priv->bank_name, offset);
+		return -EPERM;
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_SPL
+/* set GPIO pin 'gpio' as an output, with polarity 'value' */
+int tegra_spl_gpio_direction_output(int gpio, int value)
+{
+	/* Configure GPIO output value. */
+	set_level(gpio, value);
+
+	/* Configure GPIO direction as output. */
+	set_direction(gpio, value);
+
+	return 0;
+}
+#endif /* CONFIG_SPL */
+
 /*
  * Generic_GPIO primitives.
  */
 
-int gpio_request(unsigned gpio, const char *label)
+static int tegra_gpio_request(struct device *dev, unsigned offset,
+			      const char *label)
 {
-	if (gpio >= MAX_NUM_GPIOS)
-		return -1;
+	struct tegra_port_info *state = dev_get_priv(dev);
 
-	if (label != NULL) {
-		strncpy(gpio_names[gpio].name, label, GPIO_NAME_SIZE);
-		gpio_names[gpio].name[GPIO_NAME_SIZE - 1] = '\0';
-	}
+	if (*state->label[offset])
+		return -EBUSY;
+
+	strncpy(state->label[offset], label, GPIO_NAME_SIZE);
+	state->label[offset][GPIO_NAME_SIZE - 1] = '\0';
 
 	/* Configure as a GPIO */
-	set_config(gpio, 1);
+	set_config(state->base_port + offset, 1);
 
 	return 0;
 }
 
-int gpio_free(unsigned gpio)
+static int tegra_gpio_free(struct device *dev, unsigned offset)
 {
-	if (gpio >= MAX_NUM_GPIOS)
-		return -1;
+	struct tegra_port_info *state = dev_get_priv(dev);
+	int ret;
+
+	ret = check_reserved(dev, offset, __func__);
+	if (ret)
+		return ret;
+	state->label[offset][0] = '\0';
 
-	gpio_names[gpio].name[0] = '\0';
-	/* Do not configure as input or change pin mux here */
 	return 0;
 }
 
 /* read GPIO OUT value of pin 'gpio' */
-static int gpio_get_output_value(unsigned gpio)
+static int tegra_gpio_get_output_value(unsigned gpio)
 {
 	struct gpio_ctlr *ctlr = (struct gpio_ctlr *)NV_PA_GPIO_BASE;
 	struct gpio_ctlr_bank *bank = &ctlr->gpio_bank[GPIO_BANK(gpio)];
@@ -166,81 +210,234 @@ static int gpio_get_output_value(unsigned gpio)
 	return (val >> GPIO_BIT(gpio)) & 1;
 }
 
+
 /* set GPIO pin 'gpio' as an input */
-int gpio_direction_input(unsigned gpio)
+static int tegra_gpio_direction_input(struct device *dev, unsigned offset)
 {
-	debug("gpio_direction_input: pin = %d (port %d:bit %d)\n",
-		gpio, GPIO_FULLPORT(gpio), GPIO_BIT(gpio));
+	struct tegra_port_info *state = dev_get_priv(dev);
+	int ret;
+
+	ret = check_reserved(dev, offset, __func__);
+	if (ret)
+		return ret;
 
 	/* Configure GPIO direction as input. */
-	set_direction(gpio, 0);
+	set_direction(state->base_port + offset, 0);
 
 	return 0;
 }
 
 /* set GPIO pin 'gpio' as an output, with polarity 'value' */
-int gpio_direction_output(unsigned gpio, int value)
+static int tegra_gpio_direction_output(struct device *dev, unsigned offset,
+				       int value)
 {
-	debug("gpio_direction_output: pin = %d (port %d:bit %d) = %s\n",
-		gpio, GPIO_FULLPORT(gpio), GPIO_BIT(gpio),
-		value ? "HIGH" : "LOW");
+	struct tegra_port_info *state = dev_get_priv(dev);
+	int ret;
+
+	ret = check_reserved(dev, offset, __func__);
+	if (ret)
+		return ret;
 
 	/* Configure GPIO output value. */
-	set_level(gpio, value);
+	set_level(state->base_port + offset, value);
 
 	/* Configure GPIO direction as output. */
-	set_direction(gpio, 1);
+	set_direction(state->base_port + offset, 1);
 
 	return 0;
 }
 
 /* read GPIO IN value of pin 'gpio' */
-int gpio_get_value(unsigned gpio)
+static int tegra_gpio_get_value(struct device *dev, unsigned offset)
 {
-	struct gpio_ctlr *ctlr = (struct gpio_ctlr *)NV_PA_GPIO_BASE;
-	struct gpio_ctlr_bank *bank = &ctlr->gpio_bank[GPIO_BANK(gpio)];
+	struct tegra_port_info *state = dev_get_priv(dev);
+	int gpio = state->base_port + offset;
+	int ret;
 	int val;
 
-	debug("gpio_get_value: pin = %d (port %d:bit %d)\n",
-		gpio, GPIO_FULLPORT(gpio), GPIO_BIT(gpio));
+	ret = check_reserved(dev, offset, __func__);
+	if (ret)
+		return ret;
+
+	debug("%s: pin = %d (port %d:bit %d)\n", __func__,
+	      gpio, GPIO_FULLPORT(gpio), GPIO_BIT(gpio));
 
-	val = readl(&bank->gpio_in[GPIO_PORT(gpio)]);
+	val = readl(&state->bank->gpio_in[GPIO_PORT(gpio)]);
 
 	return (val >> GPIO_BIT(gpio)) & 1;
 }
 
 /* write GPIO OUT value to pin 'gpio' */
-int gpio_set_value(unsigned gpio, int value)
+static int tegra_gpio_set_value(struct device *dev, unsigned offset, int value)
 {
+	struct tegra_port_info *state = dev_get_priv(dev);
+	int gpio = state->base_port + offset;
+	int ret;
+
+	ret = check_reserved(dev, offset, __func__);
+	if (ret)
+		return ret;
+
 	debug("gpio_set_value: pin = %d (port %d:bit %d), value = %d\n",
-		gpio, GPIO_FULLPORT(gpio), GPIO_BIT(gpio), value);
+	      gpio, GPIO_FULLPORT(gpio), GPIO_BIT(gpio), value);
 
 	/* Configure GPIO output value. */
-	set_level(gpio, value);
+	set_level(state->base_port + offset, value);
 
 	return 0;
 }
 
-/*
- * Display Tegra GPIO information
+static int tegra_gpio_get_state(struct device *dev, unsigned int offset,
+				char *buf, int bufsize)
+{
+	struct gpio_dev_priv *uc_priv = dev->uclass_priv;
+	struct tegra_port_info *state = dev_get_priv(dev);
+	int gpio = state->base_port + offset;
+	const char *label;
+	int is_output;
+	int is_gpio;
+	int size;
+
+	label = state->label[offset];
+	is_gpio = get_config(state->base_port + offset); /* GPIO, not SFPIO */
+	size = snprintf(buf, bufsize, "%s%d: ",
+			uc_priv->bank_name ? uc_priv->bank_name : "", offset);
+	buf += size;
+	bufsize -= size;
+	if (is_gpio) {
+		is_output = get_direction(gpio);
+
+		snprintf(buf, bufsize, "%s: %d [%c]%s%s",
+			is_output ? "out" : " in",
+			is_output ?
+				tegra_gpio_get_output_value(gpio) :
+				tegra_gpio_get_value(dev, offset),
+			*label ? 'x' : ' ',
+			*label ? " " : "",
+			label);
+	} else {
+		snprintf(buf, bufsize, "sfpio");
+	}
+
+	return 0;
+}
+
+static const struct dm_gpio_ops gpio_tegra_ops = {
+	.request		= tegra_gpio_request,
+	.free			= tegra_gpio_free,
+	.direction_input	= tegra_gpio_direction_input,
+	.direction_output	= tegra_gpio_direction_output,
+	.get_value		= tegra_gpio_get_value,
+	.set_value		= tegra_gpio_set_value,
+	.get_state		= tegra_gpio_get_state,
+};
+
+/**
+ * Returns the name of a GPIO port
+ *
+ * GPIOs are named A, B, C, ..., Z, AA, BB, CC, ...
+ *
+ * @base_port: Base port number (0, 1..n-1)
+ * @return allocated string containing the name
  */
-void gpio_info(void)
+static char *gpio_port_name(int base_port)
 {
-	unsigned c;
-	int type;
+	char *name, *s;
+
+	name = malloc(3);
+	if (name) {
+		s = name;
+		*s++ = 'A' + (base_port % 26);
+		if (base_port >= 26)
+			*s++ = *name;
+		*s = '\0';
+	}
+
+	return name;
+}
+
+static const struct device_id tegra_gpio_ids[] = {
+	{ .compatible = "nvidia,tegra30-gpio" },
+	{ .compatible = "nvidia,tegra20-gpio" },
+	{ }
+};
+
+static int gpio_tegra_probe(struct device *dev)
+{
+	struct gpio_dev_priv *uc_priv = dev->uclass_priv;
+	struct tegra_port_info *priv = dev->priv;
+	struct tegra_gpio_platdata *plat = dev->platdata;
 
-	for (c = 0; c < MAX_NUM_GPIOS; c++) {
-		type = get_config(c);		/* GPIO, not SFPIO */
-		if (type) {
-			printf("GPIO_%d:\t%s is an %s, ", c,
-				get_name(c),
-				get_direction(c) ? "OUTPUT" : "INPUT");
-			if (get_direction(c))
-				printf("value = %d", gpio_get_output_value(c));
-			else
-				printf("value = %d", gpio_get_value(c));
-			printf("\n");
-		} else
-			continue;
+	/* Only child devices have ports */
+	if (!plat)
+		return 0;
+
+	priv->bank = plat->bank;
+	priv->base_port = plat->base_port;
+
+	uc_priv->gpio_count = TEGRA_GPIOS_PER_PORT;
+	uc_priv->bank_name = plat->port_name;
+
+	return 0;
+}
+
+/**
+ * We have a top-level GPIO device with no actual GPIOs. It has a child
+ * device for each Tegra port.
+ */
+static int gpio_tegra_bind(struct device *parent)
+{
+	struct tegra_gpio_platdata *plat = parent->platdata;
+	struct gpio_ctlr *ctlr;
+	int bank_count;
+	int bank;
+	int ret;
+	int len;
+
+	/* If this is a child device, there is nothing to do here */
+	if (plat)
+		return 0;
+
+	/*
+	 * This driver does not make use of interrupts, other than to figure
+	 * out the number of GPIO banks
+	 */
+	if (!fdt_getprop(gd->fdt_blob, parent->of_offset, "interrupts", &len))
+		return -EINVAL;
+	bank_count = len / 3 / sizeof(u32);
+	ctlr = (struct gpio_ctlr *)fdtdec_get_addr(gd->fdt_blob,
+						   parent->of_offset, "reg");
+	for (bank = 0; bank < bank_count; bank++) {
+		int port;
+
+		for (port = 0; port < TEGRA_PORTS_PER_BANK; port++) {
+			struct tegra_gpio_platdata *plat;
+			struct device *dev;
+
+			plat = calloc(1, sizeof(*plat));
+			if (!plat)
+				return -ENOMEM;
+			plat->bank = &ctlr->gpio_bank[bank];
+			plat->base_port = bank * TEGRA_PORTS_PER_BANK + port;
+			plat->port_name = gpio_port_name(plat->base_port);
+
+			ret = device_bind(parent, parent->driver,
+					  plat->port_name, plat, -1, &dev);
+			if (ret)
+				return ret;
+			dev->of_offset = parent->of_offset;
+		}
 	}
+
+	return 0;
 }
+
+U_BOOT_DRIVER(gpio_tegra) = {
+	.name	= "gpio_tegra",
+	.id	= UCLASS_GPIO,
+	.of_match = tegra_gpio_ids,
+	.bind	= gpio_tegra_bind,
+	.probe = gpio_tegra_probe,
+	.priv_auto_alloc_size = sizeof(struct tegra_port_info),
+	.ops	= &gpio_tegra_ops,
+};
diff --git a/include/configs/tegra-common.h b/include/configs/tegra-common.h
index 24b909b..1069218 100644
--- a/include/configs/tegra-common.h
+++ b/include/configs/tegra-common.h
@@ -21,6 +21,7 @@
 
 #define CONFIG_DM
 #define CONFIG_CMD_DM
+#define CONFIG_DM_GPIO
 
 #define CONFIG_SYS_TIMER_RATE		1000000
 #define CONFIG_SYS_TIMER_COUNTER	NV_PA_TMRUS_BASE
-- 
1.9.1.423.g4596e3a



More information about the U-Boot mailing list