[U-Boot] [PATCHv5 07/14] mmc: exynos_dw_mmc: restore the property into host
Jaehoon Chung
jh80.chung at samsung.com
Fri May 16 06:59:52 CEST 2014
Restore the platdata(property of dt) into host struct.
Then data's information is maintained and reused anywhere.
Signed-off-by: Jaehoon Chung <jh80.chung at samsung.com>
Tested-by: Lukasz Majewski <l.majewski at samsung.com>
Acked-by: Lukasz Majewski <l.majewski at samsung.com>
---
drivers/mmc/exynos_dw_mmc.c | 204 +++++++++++++++++++++++++++----------------
include/dwmmc.h | 2 +
2 files changed, 133 insertions(+), 73 deletions(-)
diff --git a/drivers/mmc/exynos_dw_mmc.c b/drivers/mmc/exynos_dw_mmc.c
index de8cdcc..28941ad 100644
--- a/drivers/mmc/exynos_dw_mmc.c
+++ b/drivers/mmc/exynos_dw_mmc.c
@@ -13,6 +13,8 @@
#include <asm/arch/dwmmc.h>
#include <asm/arch/clk.h>
#include <asm/arch/pinmux.h>
+#include <asm/gpio.h>
+#include <asm-generic/errno.h>
#define DWMMC_MAX_CH_NUM 4
#define DWMMC_MAX_FREQ 52000000
@@ -44,7 +46,11 @@ unsigned int exynos_dwmci_get_clk(struct dwmci_host *host)
& DWMCI_DIVRATIO_MASK) + 1;
sclk = get_mmc_clk(host->dev_index);
- return sclk / clk_div;
+ /*
+ * Assume to know divider value.
+ * When clock unit is broken, need to set "host->div"
+ */
+ return sclk / clk_div / (host->div + 1);
}
static void exynos_dwmci_board_init(struct dwmci_host *host)
@@ -60,45 +66,32 @@ static void exynos_dwmci_board_init(struct dwmci_host *host)
}
}
-/*
- * This function adds the mmc channel to be registered with mmc core.
- * index - mmc channel number.
- * regbase - register base address of mmc channel specified in 'index'.
- * bus_width - operating bus width of mmc channel specified in 'index'.
- * clksel - value to be written into CLKSEL register in case of FDT.
- * NULL in case od non-FDT.
- */
-int exynos_dwmci_add_port(int index, u32 regbase, int bus_width, u32 clksel)
+static int exynos_dwmci_core_init(struct dwmci_host *host, int index)
{
- struct dwmci_host *host = NULL;
unsigned int div;
unsigned long freq, sclk;
- host = malloc(sizeof(struct dwmci_host));
- if (!host) {
- printf("dwmci_host malloc fail!\n");
- return 1;
- }
+
+ if (host->bus_hz)
+ freq = host->bus_hz;
+ else
+ freq = DWMMC_MAX_FREQ;
+
/* request mmc clock vlaue of 52MHz. */
- freq = 52000000;
sclk = get_mmc_clk(index);
div = DIV_ROUND_UP(sclk, freq);
/* set the clock divisor for mmc */
set_mmc_clk(index, div);
host->name = "EXYNOS DWMMC";
- host->ioaddr = (void *)regbase;
- host->buswidth = bus_width;
#ifdef CONFIG_EXYNOS5420
host->quirks = DWMCI_QUIRK_DISABLE_SMU;
#endif
host->board_init = exynos_dwmci_board_init;
- if (clksel) {
- host->clksel_val = clksel;
- } else {
- if (0 == index)
+ if (!host->clksel_val) {
+ if (index == 0)
host->clksel_val = DWMMC_MMC0_CLKSEL_VAL;
- if (2 == index)
+ else if (index == 2)
host->clksel_val = DWMMC_MMC2_CLKSEL_VAL;
}
@@ -113,69 +106,134 @@ int exynos_dwmci_add_port(int index, u32 regbase, int bus_width, u32 clksel)
return 0;
}
+/*
+ * This function adds the mmc channel to be registered with mmc core.
+ * index - mmc channel number.
+ * regbase - register base address of mmc channel specified in 'index'.
+ * bus_width - operating bus width of mmc channel specified in 'index'.
+ * clksel - value to be written into CLKSEL register in case of FDT.
+ * NULL in case od non-FDT.
+ */
+int exynos_dwmci_add_port(int index, u32 regbase, int bus_width, u32 clksel)
+{
+ struct dwmci_host *host = NULL;
+
+ host = malloc(sizeof(struct dwmci_host));
+ if (!host) {
+ error("dwmci_host malloc fail!\n");
+ return -ENOMEM;
+ }
+
+ host->ioaddr = (void *)regbase;
+ host->buswidth = bus_width;
+
+ if (clksel)
+ host->clksel_val = clksel;
+
+ return exynos_dwmci_core_init(host, index);
+}
+
#ifdef CONFIG_OF_CONTROL
-int exynos_dwmmc_init(const void *blob)
+static struct dwmci_host dwmci_host[DWMMC_MAX_CH_NUM];
+
+static int do_dwmci_init(struct dwmci_host *host)
{
- int index, bus_width;
- int node_list[DWMMC_MAX_CH_NUM];
- int err = 0, dev_id, flag, count, i;
- u32 clksel_val, base, timing[3];
+ int index, flag, err;
- count = fdtdec_find_aliases_for_id(blob, "mmc",
- COMPAT_SAMSUNG_EXYNOS5_DWMMC, node_list,
- DWMMC_MAX_CH_NUM);
+ index = host->dev_index;
- for (i = 0; i < count; i++) {
- int node = node_list[i];
+ flag = host->buswidth == 8 ? PINMUX_FLAG_8BIT_MODE : PINMUX_FLAG_NONE;
+ err = exynos_pinmux_config(host->dev_id, flag);
+ if (err) {
+ debug("DWMMC not configure\n");
+ return err;
+ }
- if (node <= 0)
- continue;
+ return exynos_dwmci_core_init(host, index);
+}
- /* Extract device id for each mmc channel */
- dev_id = pinmux_decode_periph_id(blob, node);
+static int exynos_dwmci_get_config(const void *blob, int node,
+ struct dwmci_host *host)
+{
+ int err = 0;
+ u32 base, clksel_val, timing[3];
- /* Get the bus width from the device node */
- bus_width = fdtdec_get_int(blob, node, "samsung,bus-width", 0);
- if (bus_width <= 0) {
- debug("DWMMC: Can't get bus-width\n");
- return -1;
- }
- if (8 == bus_width)
- flag = PINMUX_FLAG_8BIT_MODE;
- else
- flag = PINMUX_FLAG_NONE;
+ /* Extract device id for each mmc channel */
+ host->dev_id = pinmux_decode_periph_id(blob, node);
- /* config pinmux for each mmc channel */
- err = exynos_pinmux_config(dev_id, flag);
- if (err) {
- debug("DWMMC not configured\n");
- return err;
- }
+ /* Get the bus width from the device node */
+ host->buswidth = fdtdec_get_int(blob, node, "samsung,bus-width", 0);
+ if (host->buswidth <= 0) {
+ debug("DWMMC: Can't get bus-width\n");
+ return -EINVAL;
+ }
- index = dev_id - PERIPH_ID_SDMMC0;
+ host->dev_index = fdtdec_get_int(blob, node, "index", host->dev_id);
+ if (host->dev_index == host->dev_id)
+ host->dev_index = host->dev_id - PERIPH_ID_SDMMC0;
- /* Get the base address from the device node */
- base = fdtdec_get_addr(blob, node, "reg");
- if (!base) {
- debug("DWMMC: Can't get base address\n");
- return -1;
- }
- /* Extract the timing info from the node */
- err = fdtdec_get_int_array(blob, node, "samsung,timing",
- timing, 3);
+ /* Set the base address from the device node */
+ base = fdtdec_get_addr(blob, node, "reg");
+ if (!base) {
+ debug("DWMMC: Can't get base address\n");
+ return -EINVAL;
+ }
+ host->ioaddr = (void *)base;
+
+ /* Extract the timing info from the node */
+ err = fdtdec_get_int_array(blob, node, "samsung,timing", timing, 3);
+ if (err) {
+ debug("Can't get sdr-timings for devider\n");
+ return -EINVAL;
+ }
+
+ clksel_val = (DWMCI_SET_SAMPLE_CLK(timing[0]) |
+ DWMCI_SET_DRV_CLK(timing[1]) |
+ DWMCI_SET_DIV_RATIO(timing[2]));
+ if (clksel_val)
+ host->clksel_val = clksel_val;
+
+ host->fifoth_val = fdtdec_get_int(blob, node, "fifoth_val", 0);
+ host->bus_hz = fdtdec_get_int(blob, node, "bus_hz", 0);
+ host->div = fdtdec_get_int(blob, node, "div", 0);
+
+ return 0;
+}
+
+static int exynos_dwmci_process_node(const void *blob,
+ int node_list[], int count)
+{
+ struct dwmci_host *host;
+ int i, node, err;
+
+ for (i = 0; i < count; i++) {
+ node = node_list[i];
+ if (node <= 0)
+ continue;
+ host = &dwmci_host[i];
+ err = exynos_dwmci_get_config(blob, node, host);
if (err) {
- debug("Can't get sdr-timings for divider\n");
- return -1;
+ debug("%s: failed to decode dev %d\n", __func__, i);
+ return err;
}
- clksel_val = (DWMCI_SET_SAMPLE_CLK(timing[0]) |
- DWMCI_SET_DRV_CLK(timing[1]) |
- DWMCI_SET_DIV_RATIO(timing[2]));
- /* Initialise each mmc channel */
- err = exynos_dwmci_add_port(index, base, bus_width, clksel_val);
- if (err)
- debug("dwmmc Channel-%d init failed\n", index);
+ do_dwmci_init(host);
}
return 0;
}
+
+int exynos_dwmmc_init(const void *blob)
+{
+ int compat_id;
+ int node_list[DWMMC_MAX_CH_NUM];
+ int err = 0, count;
+
+ compat_id = COMPAT_SAMSUNG_EXYNOS_DWMMC;
+
+ count = fdtdec_find_aliases_for_id(blob, "mmc",
+ compat_id, node_list, DWMMC_MAX_CH_NUM);
+ err = exynos_dwmci_process_node(blob, node_list, count);
+
+ return err;
+}
#endif
diff --git a/include/dwmmc.h b/include/dwmmc.h
index c9bdf51..14c7db8 100644
--- a/include/dwmmc.h
+++ b/include/dwmmc.h
@@ -134,7 +134,9 @@ struct dwmci_host {
unsigned int version;
unsigned int clock;
unsigned int bus_hz;
+ unsigned int div;
int dev_index;
+ int dev_id;
int buswidth;
u32 clksel_val;
u32 fifoth_val;
--
1.7.9.5
More information about the U-Boot
mailing list