[U-Boot] [PATCH 1/2] ARM: at91sam9m10g45ek: enable mci0 support

Bo Shen voice.shen at atmel.com
Wed May 21 03:27:21 CEST 2014


Hi Josh,

On 05/20/2014 06:38 PM, Josh Wu wrote:
> Enable mci0 support. And enable the mmc command in configuration file.
>
> As both CONFIG_CMD_MMC and CONFIG_CMD_USB use the CONFIG_DOS_PARTITION,
> so remove the redundant CONFIG_DOS_PARTITION definition.
>
> Signed-off-by: Josh Wu <josh.wu at atmel.com>
> ---
>   board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c |   28 +++++++++++++++++++++++
>   include/configs/at91sam9m10g45ek.h              |   15 +++++++++++-
>   2 files changed, 42 insertions(+), 1 deletion(-)
>
> diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
> index b7e2efd..fd6860b 100644
> --- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
> +++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
> @@ -15,7 +15,9 @@
>   #include <asm/arch/gpio.h>
>   #include <asm/arch/clk.h>
>   #include <lcd.h>
> +#include <mmc.h>
>   #include <atmel_lcdc.h>
> +#include <atmel_mci.h>
>   #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
>   #include <net.h>
>   #endif
> @@ -217,6 +219,29 @@ void lcd_show_board_info(void)
>   #endif /* CONFIG_LCD_INFO */
>   #endif
>
> +#ifdef CONFIG_GENERIC_ATMEL_MCI
> +void at91sam9m10g45ek_mci_hw_init(void)
> +{
> +	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
> +
> +	at91_set_a_periph(AT91_PIO_PORTA, 0, 0);	/* MCI0 CLK */
> +	at91_set_a_periph(AT91_PIO_PORTA, 1, 0);	/* MCI0 CDA */
> +	at91_set_a_periph(AT91_PIO_PORTA, 2, 0);	/* MCI0 DB0 */
> +	at91_set_a_periph(AT91_PIO_PORTA, 3, 0);	/* MCI0 DB1 */
> +	at91_set_a_periph(AT91_PIO_PORTA, 4, 0);	/* MCI0 DB2 */
> +	at91_set_a_periph(AT91_PIO_PORTA, 5, 0);	/* MCI0 DB3 */

The comments for pin should be DAx while not DBx.

> +
> +	/* Enable clock */
> +	writel(1 << ATMEL_ID_MCI0, &pmc->pcer);
> +}
> +
> +int board_mmc_init(bd_t *bis)
> +{
> +	at91_set_pio_input(AT91_PIO_PORTD, 10, 0);	/* MCI0 CD */

As we won't use it, so I think we should remove it.

> +	return atmel_mci_init((void *)ATMEL_BASE_MCI0);
> +}
> +#endif
> +
>   int board_early_init_f(void)
>   {
>   	at91_seriald_hw_init();
> @@ -247,6 +272,9 @@ int board_init(void)
>   #ifdef CONFIG_ATMEL_SPI
>   	at91_spi0_hw_init(1 << 4);
>   #endif
> +#ifdef CONFIG_GENERIC_ATMEL_MCI
> +	at91sam9m10g45ek_mci_hw_init();
> +#endif
>   #ifdef CONFIG_MACB
>   	at91sam9m10g45ek_macb_hw_init();
>   #endif
> diff --git a/include/configs/at91sam9m10g45ek.h b/include/configs/at91sam9m10g45ek.h
> index ccfda71..df277e7 100644
> --- a/include/configs/at91sam9m10g45ek.h
> +++ b/include/configs/at91sam9m10g45ek.h
> @@ -115,6 +115,20 @@
>
>   #endif
>
> +/* MMC */
> +#define CONFIG_CMD_MMC
> +
> +#ifdef CONFIG_CMD_MMC
> +#define CONFIG_MMC
> +#define CONFIG_GENERIC_MMC
> +#define CONFIG_GENERIC_ATMEL_MCI
> +#endif
> +
> +#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
> +#define CONFIG_CMD_FAT
> +#define CONFIG_DOS_PARTITION
> +#endif
> +
>   /* Ethernet */
>   #define CONFIG_MACB
>   #define CONFIG_RMII
> @@ -126,7 +140,6 @@
>   #define CONFIG_USB_EHCI
>   #define CONFIG_USB_EHCI_ATMEL
>   #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	2
> -#define CONFIG_DOS_PARTITION
>   #define CONFIG_USB_STORAGE
>
>   #define CONFIG_SYS_LOAD_ADDR		0x22000000	/* load address */
>

Best Regards,
Bo Shen


More information about the U-Boot mailing list