[U-Boot] [Patch v2 9/9] omap3: overo: Use common configurations for Overo
Ash Charles
ashcharles at gmail.com
Wed May 21 23:04:55 CEST 2014
Clean-up the board configuration file for the Gumstix Overo board by
including common omap3 definitions from ti_omap3_common.h as suggested
here [1].
[1] http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/185960
Signed-off-by: Ash Charles <ashcharles at gmail.com>
Conflicts:
include/configs/omap3_overo.h
---
include/configs/omap3_overo.h | 222 ++++++------------------------------------
1 file changed, 28 insertions(+), 194 deletions(-)
diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
index 48cadbb..7b97be9 100644
--- a/include/configs/omap3_overo.h
+++ b/include/configs/omap3_overo.h
@@ -7,80 +7,35 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-/*
- * High Level Configuration Options
- */
-#define CONFIG_OMAP /* in a TI OMAP core */
-#define CONFIG_OMAP34XX /* which is a 34XX */
-#define CONFIG_OMAP3_OVERO /* working with overo */
-#define CONFIG_OMAP_GPIO
-#define CONFIG_OMAP_COMMON
-
-#define CONFIG_SDRC /* The chip has SDRC controller */
+#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
+#define CONFIG_NAND
-#include <asm/arch/cpu.h> /* get chip and board defs */
-#include <asm/arch/omap3.h>
+#include <configs/ti_omap3_common.h>
-/*
- * Display CPU and Board information
- */
+/* Display CPU and Board information */
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
-/* Clock Defines */
-#define V_OSCK 26000000 /* Clock output from T2 */
-#define V_SCLK (V_OSCK >> 1)
-
+/* call misc_init_r */
#define CONFIG_MISC_INIT_R
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
+/* pass the revision tag */
#define CONFIG_REVISION_TAG
-#define CONFIG_OF_LIBFDT
-#define CONFIG_CMD_BOOTZ
-
-/*
- * Size of malloc() pool
- */
+/* override size of malloc() pool */
+#undef CONFIG_SYS_MALLOC_LEN
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */
-
/* Shift 128 << 15 provides 4 MiB heap to support UBI commands.
* Shift 128 << 10 provides 128 KiB heap for limited-memory devices. */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 15))
-/*
- * Hardware drivers
- */
-
-/*
- * NS16550 Configuration
- */
-#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
-
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
-
-/*
- * select serial console configuration
- */
-#define CONFIG_CONS_INDEX 3
-#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
-#define CONFIG_SERIAL3 3
+/* I2C Support */
+#define CONFIG_SYS_I2C_OMAP34XX
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, \
- 115200}
-#define CONFIG_GENERIC_MMC
-#define CONFIG_MMC
-#define CONFIG_OMAP_HSMMC
-#define CONFIG_DOS_PARTITION
+/* TWL4030 LED */
+#define CONFIG_TWL4030_LED
+/* Initialize GPIOs by default */
#define CONFIG_OMAP3_GPIO_2 /* GPIO32..63 is in GPIO Bank 2 */
#define CONFIG_OMAP3_GPIO_3 /* GPIO64..95 is in GPIO Bank 3 */
#define CONFIG_OMAP3_GPIO_4 /* GPIO96..127 is in GPIO Bank 4 */
@@ -88,34 +43,18 @@
#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO Bank 6 */
/* commands to include */
-#include <config_cmd_default.h>
-
#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_EXT2 /* EXT2 Support */
-#define CONFIG_CMD_FAT /* FAT support */
-#define CONFIG_CMD_FS_GENERIC
-
-#define CONFIG_CMD_I2C /* I2C serial bus support */
-#define CONFIG_CMD_MMC /* MMC support */
-#define CONFIG_CMD_NAND /* NAND support */
-
-#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
#undef CONFIG_CMD_IMI /* iminfo */
-#undef CONFIG_CMD_IMLS /* List all found images */
#undef CONFIG_CMD_NFS /* NFS support */
-#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
-
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_CMD_MTDPARTS /* MTD partition support */
+#ifdef CONFIG_NAND
#define CONFIG_CMD_UBI /* UBI-formated MTD partition support */
#define CONFIG_CMD_UBIFS /* Read-only UBI volume operations */
#define CONFIG_RBTREE /* required by CONFIG_CMD_UBI */
#define CONFIG_LZO /* required by CONFIG_CMD_UBIFS */
-#define CONFIG_MTD_DEVICE /* required by CONFIG_CMD_MTDPARTS */
#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
/* NAND block size is 128 KiB. Synchronize these values with
@@ -133,41 +72,18 @@
"256k(environ)," \
"8m(linux)," \
"-(rootfs)"
-#else /* CONFIG_CMD_NAND */
+#else /* CONFIG_NAND */
#define MTDPARTS_DEFAULT
-#endif /* CONFIG_CMD_NAND */
+#endif /* CONFIG_NAND */
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
-#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
-#define CONFIG_SYS_I2C_OMAP34XX
-
-/*
- * TWL4030
- */
-#define CONFIG_TWL4030_POWER
-#define CONFIG_TWL4030_LED
-
-/*
- * Board NAND Info.
- */
+/* Board NAND Info. */
#define CONFIG_SYS_NAND_QUIET_TEST
-#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
/* to access nand */
-#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
- /* to access nand */
- /* at CS0 */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
- /* devices */
/* Environment information */
-#define CONFIG_BOOTDELAY 5
-
#define CONFIG_EXTRA_ENV_SETTINGS \
- "loadaddr=0x82000000\0" \
- "dtbaddr=0x81600000\0" \
- "dtbfile=overo.dtb\0" \
+ DEFAULT_LINUX_BOOT_ENV \
+ "fdtfile=overo.dtb\0" \
"bootdir=/boot\0" \
"bootfile=zImage\0" \
"usbtty=cdc_acm\0" \
@@ -210,10 +126,10 @@
"run mmcargs; " \
"bootm ${loadaddr}\0" \
"loadzimage=load mmc ${mmcdev}:2 ${loadaddr} ${bootdir}/${bootfile}\0" \
- "loadfdt=load mmc ${mmcdev}:2 ${dtbaddr} ${bootdir}/${dtbfile}\0" \
+ "loadfdt=load mmc ${mmcdev}:2 ${fdtaddr} ${bootdir}/${fdtfile}\0" \
"mmcbootfdt=echo Booting with DT from mmc ...; " \
"run mmcargs; " \
- "bootz ${loadaddr} - ${dtbaddr}\0" \
+ "bootz ${loadaddr} - ${fdtaddr}\0" \
"nandboot=echo Booting from nand ...; " \
"run nandargs; " \
"nand read ${loadaddr} linux; " \
@@ -236,7 +152,7 @@
"run mmcboot;" \
"fi;" \
"if run loadzimage; then " \
- "if test -n $dtbfile; then " \
+ "if test -n $fdtfile; then " \
"if run loadfdt; then " \
"run mmcbootfdt;" \
"fi;" \
@@ -245,56 +161,23 @@
"fi;" \
"run nandboot; " \
-#define CONFIG_AUTO_COMPLETE 1
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#undef CONFIG_SYS_PROMPT
#define CONFIG_SYS_PROMPT "Overo # "
-#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command */
- /* args */
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
/* memtest works on */
#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
0x01F00000) /* 31MB */
-#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
- /* address */
-/*
- * OMAP3 has 12 GP timers, they can be driven by the system clock
- * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
- * This rate is divided by a local divisor.
- */
-#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
-#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
-#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-
-/* **** PISMO SUPPORT *** */
-
+/* FLASH and environment organization */
/* Configure the PISMO */
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
-
-#if defined(CONFIG_CMD_NAND)
+#if defined(CONFIG_NAND)
#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
#endif
@@ -310,67 +193,18 @@
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+/* Configure SMSC9211 ethernet */
#if defined(CONFIG_CMD_NET)
-/*----------------------------------------------------------------------------
- * SMSC9211 Ethernet from SMSC9118 family
- *----------------------------------------------------------------------------
- */
-
#define CONFIG_SMC911X
#define CONFIG_SMC911X_32_BIT
#define CONFIG_SMC911X_BASE 0x2C000000
-
#endif /* (CONFIG_CMD_NET) */
-/*
- * Leave it at 0x80008000 to allow booting new u-boot.bin with X-loader
- * and older u-boot.bin with the new U-Boot SPL.
- */
-#define CONFIG_SYS_TEXT_BASE 0x80008000
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+/* Initial RAM setup */
#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
#define CONFIG_SYS_INIT_RAM_SIZE 0x800
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
#define CONFIG_SYS_CACHELINE_SIZE 64
-/* Defines for SPL */
-#define CONFIG_SPL
-#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_NAND_SIMPLE
-#define CONFIG_SPL_TEXT_BASE 0x40200800
-#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
-#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
-
-/* move malloc and bss high to prevent clashing with the main image */
-#define CONFIG_SYS_SPL_MALLOC_START 0x87000000
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
-#define CONFIG_SPL_BSS_START_ADDR 0x87080000 /* end of minimum RAM */
-#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
-
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
-#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
-#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
-
-#define CONFIG_SPL_BOARD_INIT
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBDISK_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_MMC_SUPPORT
-#define CONFIG_SPL_FAT_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_NAND_BASE
-#define CONFIG_SPL_NAND_DRIVERS
-#define CONFIG_SPL_NAND_ECC
-#define CONFIG_SPL_GPIO_SUPPORT
-#define CONFIG_SPL_POWER_SUPPORT
-#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
-
/* NAND boot config */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
--
1.8.3.2
More information about the U-Boot
mailing list