[U-Boot] [PATCH 1/5] imx:mx6sxsabresd add usb support

Peng Fan Peng.Fan at freescale.com
Sat Nov 1 03:19:15 CET 2014


Add usb support for mx6sxsabresd board.

Signed-off-by: Peng Fan <Peng.Fan at freescale.com>
Signed-off-by: Ye.Li <B37916 at freescale.com>
---
 board/freescale/mx6sxsabresd/mx6sxsabresd.c | 29 +++++++++++++++++++++++++++++
 include/configs/mx6sxsabresd.h              | 14 ++++++++++++++
 2 files changed, 43 insertions(+)

diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
index 256ea29..016b8e8 100644
--- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c
+++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
@@ -296,3 +296,32 @@ int checkboard(void)
 
 	return 0;
 }
+
+#ifdef CONFIG_USB_EHCI_MX6
+iomux_v3_cfg_t const usb_otg1_pads[] = {
+	MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL)
+};
+
+iomux_v3_cfg_t const usb_otg2_pads[] = {
+	MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+int board_ehci_hcd_init(int port)
+{
+	switch (port) {
+	case 0:
+		imx_iomux_v3_setup_multiple_pads(usb_otg1_pads,
+						 ARRAY_SIZE(usb_otg1_pads));
+		break;
+	case 1:
+		imx_iomux_v3_setup_multiple_pads(usb_otg2_pads,
+						 ARRAY_SIZE(usb_otg2_pads));
+		break;
+	default:
+		printf("MXC USB port %d not yet supported\n", port);
+		return 1;
+	}
+	return 0;
+}
+#endif
diff --git a/include/configs/mx6sxsabresd.h b/include/configs/mx6sxsabresd.h
index e02ea18..8edf187 100644
--- a/include/configs/mx6sxsabresd.h
+++ b/include/configs/mx6sxsabresd.h
@@ -198,6 +198,20 @@
 #define CONFIG_PHYLIB
 #define CONFIG_PHY_ATHEROS
 
+
+#define CONFIG_CMD_USB
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_USB_STORAGE
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS   0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#endif
+
 #define CONFIG_CMD_PCI
 #ifdef CONFIG_CMD_PCI
 #define CONFIG_PCI
-- 
1.8.4.5



More information about the U-Boot mailing list