[U-Boot] [PATCH v2 4/4] Odroid-XU3: Add support for Odroid-XU3
Lukasz Majewski
l.majewski at samsung.com
Mon Nov 3 10:09:19 CET 2014
Hi Hyungwon,
> This patch adds support for Odroid-XU3.
>
> Signed-off-by: Hyungwon Hwang <human.hwang at samsung.com>
> ---
> arch/arm/cpu/armv7/exynos/Kconfig | 4 ++
> arch/arm/dts/Makefile | 3 +-
> arch/arm/dts/exynos5422-odroidxu3.dts | 72 +++++++++++++++++++
> board/samsung/odroid-xu3/Kconfig | 12 ++++
> board/samsung/odroid-xu3/MAINTAINERS | 6 ++
> board/samsung/odroid-xu3/Makefile | 7 ++
> board/samsung/odroid-xu3/odroid-xu3.c | 132
> ++++++++++++++++++++++++++++++++++
> board/samsung/odroid-xu3/setup.h | 115
> +++++++++++++++++++++++++++++ configs/odroid-xu3_defconfig
> | 4 ++ include/configs/odroid_xu3.h | 73
> +++++++++++++++++++ 10 files changed, 427 insertions(+), 1
> deletion(-) create mode 100644 arch/arm/dts/exynos5422-odroidxu3.dts
> create mode 100644 board/samsung/odroid-xu3/Kconfig create mode
> 100644 board/samsung/odroid-xu3/MAINTAINERS create mode 100644
> board/samsung/odroid-xu3/Makefile create mode 100644
> board/samsung/odroid-xu3/odroid-xu3.c create mode 100644
> board/samsung/odroid-xu3/setup.h create mode 100644
> configs/odroid-xu3_defconfig create mode 100644
> include/configs/odroid_xu3.h
>
> diff --git a/arch/arm/cpu/armv7/exynos/Kconfig
> b/arch/arm/cpu/armv7/exynos/Kconfig index 3a25fee..a47cb34 100644
> --- a/arch/arm/cpu/armv7/exynos/Kconfig
> +++ b/arch/arm/cpu/armv7/exynos/Kconfig
> @@ -22,6 +22,9 @@ config TARGET_TRATS2
> config TARGET_ODROID
> bool "Exynos4412 Odroid board"
>
> +config TARGET_ODROID_XU3
> + bool "Exynos5422 Odroid board"
> +
> config TARGET_ARNDALE
> bool "Exynos5250 Arndale board"
> select OF_CONTROL if !SPL_BUILD
> @@ -60,6 +63,7 @@ source "board/samsung/universal_c210/Kconfig"
> source "board/samsung/origen/Kconfig"
> source "board/samsung/trats2/Kconfig"
> source "board/samsung/odroid/Kconfig"
> +source "board/samsung/odroid-xu3/Kconfig"
> source "board/samsung/arndale/Kconfig"
> source "board/samsung/smdk5250/Kconfig"
> source "board/samsung/smdk5420/Kconfig"
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 2dcfcc0..66191f9 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -12,7 +12,8 @@ dtb-$(CONFIG_EXYNOS5) += exynos5250-arndale.dtb \
> exynos5250-smdk5250.dtb \
> exynos5420-smdk5420.dtb \
> exynos5420-peach-pit.dtb \
> - exynos5800-peach-pi.dtb
> + exynos5800-peach-pi.dtb \
> + exynos5422-odroidxu3.dtb
> dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
> tegra20-medcom-wide.dtb \
> tegra20-paz00.dtb \
> diff --git a/arch/arm/dts/exynos5422-odroidxu3.dts
> b/arch/arm/dts/exynos5422-odroidxu3.dts new file mode 100644
> index 0000000..34f52c6
> --- /dev/null
> +++ b/arch/arm/dts/exynos5422-odroidxu3.dts
> @@ -0,0 +1,72 @@
> +/*
> + * Odroid XU3 device tree source
> + *
> + * Copyright (c) 2014 Samsung Electronics Co., Ltd.
> + * http://www.samsung.com
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +/dts-v1/;
> +/include/ "exynos54xx.dtsi"
> +
> +/ {
> + model = "Odroid XU3 based on EXYNOS5422";
> + compatible = "samsung,odroidxu3", "samsung,exynos5";
> +
> + config {
> + hwid = "smdk5420 TEST A-A 9382";
> + };
> +
> + aliases {
> + serial0 = "/serial at 12C00000";
> + console = "/serial at 12C20000";
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0x40000000 0x10000000
> + 0x50000000 0x10000000
> + 0x60000000 0x10000000
> + 0x70000000 0x10000000
> + 0x80000000 0x10000000
> + 0x90000000 0x10000000
> + 0xa0000000 0x10000000
> + 0xb0000000 0xea00000>;
> + };
> +
> + serial at 12C20000 {
> + status="okay";
> + };
> +
> + /* s2mps11 is on i2c bus 4 */
> + i2c at 12ca0000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pmic at 66 {
> + reg = <0x66>;
> + compatible = "samsung,s2mps11-pmic";
> + };
> + };
> +
> + mmc at 12200000 {
> + samsung,bus-width = <8>;
> + samsung,timing = <1 3 3>;
> + samsung,removable = <0>;
> + samsung,pre-init;
> + };
> +
> + mmc at 12210000 {
> + status = "disabled";
> + };
> +
> + mmc at 12220000 {
> + samsung,bus-width = <4>;
> + samsung,timing = <1 2 3>;
> + samsung,removable = <1>;
> + };
> +
> + mmc at 12230000 {
> + status = "disabled";
> + };
> +};
> diff --git a/board/samsung/odroid-xu3/Kconfig
> b/board/samsung/odroid-xu3/Kconfig new file mode 100644
> index 0000000..6159692
> --- /dev/null
> +++ b/board/samsung/odroid-xu3/Kconfig
> @@ -0,0 +1,12 @@
> +if TARGET_ODROID_XU3
> +
> +config SYS_BOARD
> + default "odroid-xu3"
> +
> +config SYS_VENDOR
> + default "samsung"
> +
> +config SYS_CONFIG_NAME
> + default "odroid_xu3"
> +
> +endif
> diff --git a/board/samsung/odroid-xu3/MAINTAINERS
> b/board/samsung/odroid-xu3/MAINTAINERS new file mode 100644
> index 0000000..50cf928
> --- /dev/null
> +++ b/board/samsung/odroid-xu3/MAINTAINERS
> @@ -0,0 +1,6 @@
> +ODROID-XU3 BOARD
> +M: Hyungwon Hwang <human.hwang at samsung.com>
> +S: Maintained
> +F: board/samsung/odroid-xu3/
> +F: include/configs/odroid_xu3.h
> +F: configs/odroid-xu3_defconfig
> diff --git a/board/samsung/odroid-xu3/Makefile
> b/board/samsung/odroid-xu3/Makefile new file mode 100644
> index 0000000..85ae5c5
> --- /dev/null
> +++ b/board/samsung/odroid-xu3/Makefile
> @@ -0,0 +1,7 @@
> +#
> +# Copyright (c) 2014 Samsung Electronics Co., Ltd. All rights
> reserved. +#
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +
> +obj-y := odroid-xu3.o
> diff --git a/board/samsung/odroid-xu3/odroid-xu3.c
> b/board/samsung/odroid-xu3/odroid-xu3.c new file mode 100644
> index 0000000..f1d8667
> --- /dev/null
> +++ b/board/samsung/odroid-xu3/odroid-xu3.c
> @@ -0,0 +1,132 @@
> +/*
> + * Copyright (C) 2014 Samsung Electronics
> + * Hyungwon Hwang <human.hwang at samsung.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <asm/io.h>
> +#include <netdev.h>
> +#include <asm/arch/cpu.h>
> +#include <asm/arch/clock.h>
> +#include <asm/arch/power.h>
> +#include <asm/arch/gpio.h>
> +#include <asm/arch/mmc.h>
> +#include <asm/arch/pinmux.h>
> +#include <asm/arch/sromc.h>
> +#include "../setup.h"
> +#include "setup.h"
I've pointed it out in the previous mail.
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +unsigned int get_board_rev(void)
> +{
> + unsigned int rev = 0;
> + return rev;
> +}
> +
> +int exynos_init(void)
> +{
> + return 0;
> +}
> +
> +static int board_clock_init(void)
> +{
> + unsigned int set, clr, clr_src_cpu, clr_pll_con0;
> + struct exynos5420_clock *clk = (struct exynos5420_clock *)
> +
> samsung_get_base_clock();
> + /*
> + * CMU_CPU clocks src to MPLL
> + * Bit values: 0 ; 1
> + * MUX_APLL_SEL: FIN_PLL ; FOUT_APLL
> + * MUX_CORE_SEL: MOUT_APLL ; SCLK_MPLL
> + * MUX_HPM_SEL: MOUT_APLL ; SCLK_MPLL_USER_C
> + * MUX_MPLL_USER_SEL_C: FIN_PLL ; SCLK_MPLL
> + */
> +
> + /* Set CMU_CPU clocks src to OSCCLK */
> + clr_src_cpu = MUX_APLL_SEL(1) | MUX_CORE_SEL(1);
> + set = MUX_APLL_SEL(0) | MUX_CORE_SEL(1);
> +
> + clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set);
> +
> + while (MUX_STAT_CPU_CHANGING(readl(&clk->mux_stat_cpu)))
> + continue;
> +
> + /* Set APLL to 1200MHz */
> + clr_pll_con0 = SDIV(7) | PDIV(63) | MDIV(1023) | FSEL(1) |
> + PLL_ENABLE(1);
> + set = SDIV(0) | PDIV(2) | MDIV(100) | PLL_ENABLE(1);
> +
> + clrsetbits_le32(&clk->apll_con0, clr_pll_con0, set);
> +
> + while (!(readl(&clk->apll_con0) & PLL_LOCKED_BIT))
> + continue;
> +
> + /* Set CMU_CPU clocks src to APLL */
> + set = MUX_APLL_SEL(1) | MUX_CORE_SEL(0);
> + clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set);
> +
> + while (MUX_STAT_CPU_CHANGING(readl(&clk->mux_stat_cpu)))
> + continue;
> +
> + clr = ARM_RATIO(7) | CPUD_RATIO(7) | ATB_RATIO(7) |
> + PCLK_DBG_RATIO(7) | APLL_RATIO(7) | ARM2_RATIO(7);
> + set = ARM_RATIO(0) | CPUD_RATIO(2) | ATB_RATIO(5) |
> + PCLK_DBG_RATIO(5) | APLL_RATIO(0) | ARM2_RATIO(0);
> +
> + clrsetbits_le32(&clk->div_cpu0, clr, set);
> +
> + while (readl(&clk->div_stat_cpu0) & DIV_STAT_CPU0_CHANGING)
> + continue;
> +
> + /* Set MPLL to 800MHz */
> + set = SDIV(1) | PDIV(3) | MDIV(200) | PLL_ENABLE(1);
> +
> + clrsetbits_le32(&clk->mpll_con0, clr_pll_con0, set);
> +
> + while (!(readl(&clk->mpll_con0) & PLL_LOCKED_BIT))
> + continue;
> +
> + /* Set CLKMUX_UART src to MPLL */
> + clr = UART0_SEL(7) | UART1_SEL(7) | UART2_SEL(7) |
> UART3_SEL(7);
> + set = UART0_SEL(3) | UART1_SEL(3) | UART2_SEL(3) |
> UART3_SEL(3); +
> + clrsetbits_le32(&clk->src_peric0, clr, set);
> +
> + /* Set SCLK_UART to 400 MHz (MPLL / 2) */
> + clr = UART0_RATIO(15) | UART1_RATIO(15) | UART2_RATIO(15) |
> + UART3_RATIO(15);
> + set = UART0_RATIO(1) | UART1_RATIO(1) | UART2_RATIO(1) |
> + UART3_RATIO(1);
> +
> + clrsetbits_le32(&clk->div_peric0, clr, set);
> +
> + while (readl(&clk->div_stat_peric0) &
> DIV_STAT_PERIC0_CHANGING)
> + continue;
> +
> + /* Set CLKMUX_MMC src to MPLL */
> + clr = MUX_MMC0_SEL(7) | MUX_MMC1_SEL(7) | MUX_MMC2_SEL(7);
> + set = MUX_MMC0_SEL(3) | MUX_MMC1_SEL(3) | MUX_MMC2_SEL(3);
> +
> + clrsetbits_le32(&clk->src_fsys, clr, set);
> +
> + clr = MMC0_RATIO(0x3ff) | MMC1_RATIO(0x3ff) |
> MMC2_RATIO(0x3ff);
> + set = MMC0_RATIO(0) | MMC1_RATIO(0) | MMC2_RATIO(0);
> +
> + clrsetbits_le32(&clk->div_fsys1, clr, set);
> +
> + /* Wait for divider ready status */
> + while (readl(&clk->div_stat_fsys1) & DIV_STAT_FSYS1_CHANGING)
> + continue;
> +
> + return 0;
> +}
> +
> +#ifdef CONFIG_BOARD_EARLY_INIT_F
> +int exynos_early_init_f(void)
> +{
> + return board_clock_init();
> +}
> +#endif
> diff --git a/board/samsung/odroid-xu3/setup.h
> b/board/samsung/odroid-xu3/setup.h new file mode 100644
> index 0000000..afec01f
> --- /dev/null
> +++ b/board/samsung/odroid-xu3/setup.h
> @@ -0,0 +1,115 @@
> +/*
> + * (C) Copyright 2014 Samsung Electronics
> + * Hyungwon Hwang <human.hwang at samsung.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __ODROID_XU3_SETUP__
> +#define __ODROID_XU3_SETUP__
> +
> +/* CLK_SRC_CPU */
> +#define MUX_APLL_SEL(x) ((x) & 0x1)
> +#define MUX_CORE_SEL(x) (((x) & 0x1) << 16)
> +
> +/* CLK_MUX_STAT_CPU */
> +#define APLL_SEL(x) ((x) & 0x7)
> +#define CORE_SEL(x) (((x) & 0x7) << 16)
> +#define MUX_STAT_CPU_CHANGING(x) !(((x) & APLL_SEL(0))
> || \
> + (x) & APLL_SEL(1)
> || \
> + (x) & CORE_SEL(0)
> || \
> + (x) & CORE_SEL(1))
> +
> +/* CLK_DIV_CPU0 */
> +#define ARM_RATIO(x) ((x) & 0x7)
> +#define CPUD_RATIO(x) (((x) & 0x7) << 4)
> +#define ATB_RATIO(x) (((x) & 0x7) << 16)
> +#define PCLK_DBG_RATIO(x) (((x) & 0x7) << 20)
> +#define APLL_RATIO(x) (((x) & 0x7) << 24)
> +#define ARM2_RATIO(x) (((x) & 0x7) << 28)
> +
> +/* CLK_DIV_STAT_CPU0 */
> +#define DIV_CPUD(x) (((x) & 0x1) << 4)
> +#define DIV_ATB(x) (((x) & 0x1) << 16)
> +#define DIV_PCLK_DBG(x) (((x) & 0x1) << 20)
> +#define DIV_APLL(x) (((x) & 0x1) << 24)
> +#define DIV_ARM2(x) (((x) & 0x1) << 28)
> +
> +#define DIV_STAT_CHANGING 0x1
> +#define DIV_STAT_CPU0_CHANGING (DIV_CPUD(DIV_STAT_CHANGING) | \
> + DIV_ATB(DIV_STAT_CHANGING) | \
> + DIV_PCLK_DBG(DIV_STAT_CHANGING) | \
> + DIV_APLL(DIV_STAT_CHANGING) | \
> + DIV_ARM2(DIV_STAT_CHANGING))
> +
> +/* Set CLK_SRC_PERIC0 */
> +#define UART0_SEL(x) (((x) & 0xf) << 4)
> +#define UART1_SEL(x) (((x) & 0xf) << 8)
> +#define UART2_SEL(x) (((x) & 0xf) << 12)
> +#define UART3_SEL(x) (((x) & 0xf) << 16)
> +
> +/* Set CLK_DIV_PERIL0 */
> +#define UART0_RATIO(x) (((x) & 0xf) << 8)
> +#define UART1_RATIO(x) (((x) & 0xf) << 12)
> +#define UART2_RATIO(x) (((x) & 0xf) << 16)
> +#define UART3_RATIO(x) (((x) & 0xf) << 20)
> +
> +/* Set CLK_DIV_STAT_PERIL0 */
> +#define DIV_UART0(x) ((x) & 0x1)
> +#define DIV_UART1(x) (((x) & 0x1) << 4)
> +#define DIV_UART2(x) (((x) & 0x1) << 8)
> +#define DIV_UART3(x) (((x) & 0x1) << 12)
> +#define DIV_UART4(x) (((x) & 0x1) << 16)
> +
> +#define DIV_STAT_PERIC0_CHANGING (DIV_UART4(DIV_STAT_CHANGING) | \
> + DIV_UART3(DIV_STAT_CHANGING) | \
> + DIV_UART2(DIV_STAT_CHANGING) | \
> + DIV_UART1(DIV_STAT_CHANGING) | \
> + DIV_UART0(DIV_STAT_CHANGING))
> +
> +/* CLK_SRC_FSYS */
> +#define MUX_MMC0_SEL(x) (((x) & 0x7) << 8)
> +#define MUX_MMC1_SEL(x) (((x) & 0x7) << 12)
> +#define MUX_MMC2_SEL(x) (((x) & 0x7) << 16)
> +
> +/* CLK_DIV_FSYS1 */
> +#define MMC0_RATIO(x) ((x) & 0x3ff)
> +#define MMC1_RATIO(x) (((x) & 0x3ff) << 10)
> +#define MMC2_RATIO(x) (((x) & 0x3ff) << 20)
> +
> +#define DIV_MMC0(x) (((x) & 1) << 20)
> +#define DIV_MMC1(x) (((x) & 1) << 24)
> +#define DIV_MMC2(x) (((x) & 1) << 28)
> +
> +#define DIV_STAT_FSYS1_CHANGING (DIV_MMC0(DIV_STAT_CHANGING)
> | \
> + DIV_MMC1(DIV_STAT_CHANGING) | \
> + DIV_MMC2(DIV_STAT_CHANGING))
> +
> +#define MPLL_FOUT_SEL_SHIFT 4
> +#define EXYNOS5_EPLLCON0_LOCKED_SHIFT 29 /* EPLL Locked bit
> position*/ +#define TIMEOUT_EPLL_LOCK 1000
> +
> +#define AUDIO_0_RATIO_MASK 0x0f
> +#define AUDIO_1_RATIO_MASK 0x0f
> +
> +#define AUDIO0_SEL_MASK 0xf
> +#define AUDIO1_SEL_MASK 0xf
> +
> +#define CLK_SRC_SCLK_EPLL 0x7
> +#define CLK_SRC_MOUT_EPLL (1<<12)
> +#define AUDIO_CLKMUX_ASS (1<<0)
> +
> +/* CON0 bit-fields */
> +#define EPLL_CON0_MDIV_MASK 0x1ff
> +#define EPLL_CON0_PDIV_MASK 0x3f
> +#define EPLL_CON0_SDIV_MASK 0x7
> +#define EPLL_CON0_MDIV_SHIFT 16
> +#define EPLL_CON0_PDIV_SHIFT 8
> +#define EPLL_CON0_SDIV_SHIFT 0
> +#define EPLL_CON0_LOCK_DET_EN_SHIFT 28
> +#define EPLL_CON0_LOCK_DET_EN_MASK 1
> +
> +#define MPLL_FOUT_SEL_MASK 0x1
> +#define BPLL_FOUT_SEL_SHIFT 0
> +#define BPLL_FOUT_SEL_MASK 0x1
> +#endif
> diff --git a/configs/odroid-xu3_defconfig
> b/configs/odroid-xu3_defconfig new file mode 100644
> index 0000000..74aa0cf
> --- /dev/null
> +++ b/configs/odroid-xu3_defconfig
> @@ -0,0 +1,4 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_EXYNOS=y
> +CONFIG_TARGET_ODROID_XU3=y
> +CONFIG_DEFAULT_DEVICE_TREE="exynos5422-odroidxu3"
> diff --git a/include/configs/odroid_xu3.h
> b/include/configs/odroid_xu3.h new file mode 100644
> index 0000000..867ac74
> --- /dev/null
> +++ b/include/configs/odroid_xu3.h
> @@ -0,0 +1,73 @@
> +/*
> + * Copyright (C) 2013 Samsung Electronics
> + * Hyungwon Hwang <human.hwang at samsung.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __CONFIG_ODROID_XU3_H
> +#define __CONFIG_ODROID_XU3_H
> +
> +#include "exynos5-common.h"
> +
> +#define CONFIG_SYS_PROMPT "ODROID-XU3 # "
> +#define CONFIG_IDENT_STRING " for ODROID-XU3"
> +
> +#define CONFIG_OF_CONTROL
> +#define CONFIG_BOARD_COMMON
It is now possible to specify those two CONFIGs in odroidxu3_defconfig
using Kconfig (board/samsung/odroid/setup.h).
> +
> +#define CONFIG_SYS_SDRAM_BASE 0x40000000
> +#define CONFIG_SYS_TEXT_BASE 0x43E00000
> +
> +/* select serial console configuration */
> +#define CONFIG_SERIAL2 /* use SERIAL 2 */
> +
> +#define TZPC_BASE_OFFSET 0x10000
> +
> +#define CONFIG_CMD_MMC
> +#define CONFIG_CMD_EXT2
> +#define CONFIG_CMD_FAT
> +
> +/*
> + * FIXME: The number of bank is actually 8. But there is no way to
> reserver the
> + * last 16 Mib in the last bank now. So I just excluded the last bank
> + * temporally.
> + */
> +#define CONFIG_NR_DRAM_BANKS 7
> +#define SDRAM_BANK_SIZE (256UL << 20UL) /* 256
> MB */ +
> +#define CONFIG_ENV_IS_IN_MMC
> +
> +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR -
> 0x1000000) +
> +/* FIXME: MUST BE REMOVED AFTER TMU IS TURNED ON */
> +#undef CONFIG_EXYNOS_TMU
> +#undef CONFIG_TMU_CMD_DTT
> +
> +#undef CONFIG_EXYNOS_SPL
> +#undef CONFIG_SILENT_CONSOLE
> +#undef CONFIG_CROS_EC
> +#undef CONFIG_CROS_EC_SPI
> +#undef CONFIG_CROS_EC_I2C
> +#undef CONFIG_CROS_EC_KEYB
> +#undef CONFIG_CMD_CROS_EC
> +#undef CONFIG_KEYBOARD
> +#undef CONFIG_SPI_BOOTING
> +#undef CONFIG_ENV_IS_IN_SPI_FLASH
> +#undef CONFIG_SPI_FLASH
> +#undef CONFIG_EXYNOS_SPI
> +#undef CONFIG_CMD_SF
> +#undef CONFIG_CMD_SPI
> +#undef CONFIG_SPI_FLASH_WINBOND
> +#undef CONFIG_SPI_FLASH_GIGADEVICE
> +#undef CONFIG_OF_SPI
> +#undef CONFIG_FIT_BEST_MATCH
> +#undef CONFIG_USB_BOOTING
> +#undef CONFIG_CMD_NET
> +#undef CONFIG_SMC911X
> +#undef CONFIG_CMD_PXE
> +#undef CONFIG_MENU
> +#undef CONFIG_ENV_IS_IN_SPI_FLASH
> +
> +
> +#endif /* __CONFIG_H */
--
Best regards,
Lukasz Majewski
Samsung R&D Institute Poland (SRPOL) | Linux Platform Group
More information about the U-Boot
mailing list