[U-Boot] [PATCH 1/9] sun6i: Add new p2wi controller driver
Hans de Goede
hdegoede at redhat.com
Mon Nov 3 16:34:26 CET 2014
From: Oliver Schinagl <oliver at schinagl.nl>
The A31 uses a new push-pull two wire interface, which features higher
transfer speeds (upto 6 MHz) in theory. While the hardware can burst 8
bytes each time, this driver will only see very little use and thus is
limited to single byte transmission only.
Signed-off-by: Oliver Schinagl <oliver at schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede at redhat.com>
---
arch/arm/cpu/armv7/sunxi/Makefile | 1 +
arch/arm/cpu/armv7/sunxi/p2wi.c | 117 +++++++++++++++++++++++++++
arch/arm/include/asm/arch-sunxi/gpio.h | 3 +
arch/arm/include/asm/arch-sunxi/p2wi.h | 140 +++++++++++++++++++++++++++++++++
4 files changed, 261 insertions(+)
create mode 100644 arch/arm/cpu/armv7/sunxi/p2wi.c
create mode 100644 arch/arm/include/asm/arch-sunxi/p2wi.h
diff --git a/arch/arm/cpu/armv7/sunxi/Makefile b/arch/arm/cpu/armv7/sunxi/Makefile
index 82dbf76..b3a3601 100644
--- a/arch/arm/cpu/armv7/sunxi/Makefile
+++ b/arch/arm/cpu/armv7/sunxi/Makefile
@@ -13,6 +13,7 @@ obj-y += clock.o
obj-y += pinmux.o
obj-$(CONFIG_MACH_SUN6I) += prcm.o
obj-$(CONFIG_MACH_SUN8I) += prcm.o
+obj-$(CONFIG_MACH_SUN6I) += p2wi.o
obj-$(CONFIG_MACH_SUN4I) += clock_sun4i.o
obj-$(CONFIG_MACH_SUN5I) += clock_sun4i.o
obj-$(CONFIG_MACH_SUN6I) += clock_sun6i.o
diff --git a/arch/arm/cpu/armv7/sunxi/p2wi.c b/arch/arm/cpu/armv7/sunxi/p2wi.c
new file mode 100644
index 0000000..10df348
--- /dev/null
+++ b/arch/arm/cpu/armv7/sunxi/p2wi.c
@@ -0,0 +1,117 @@
+/*
+ * Sunxi A31 Power Management Unit
+ *
+ * (C) Copyright 2013 Oliver Schinagl <oliver at schinagl.nl>
+ * http://linux-sunxi.org
+ *
+ * Based on sun6i sources and earlier U-Boot Allwiner A10 SPL work
+ *
+ * (C) Copyright 2006-2013
+ * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
+ * Berg Xing <bergxing at allwinnertech.com>
+ * Tom Cubie <tangliang at allwinnertech.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/p2wi.h>
+#include <asm/arch/prcm.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+
+void p2wi_init(void)
+{
+ struct sunxi_p2wi_reg *p2wi = (struct sunxi_p2wi_reg *)SUNXI_P2WI_BASE;
+
+ /* Enable p2wi and PIO clk, and de-assert their resets */
+ prcm_apb0_enable(PRCM_APB0_GATE_PIO | PRCM_APB0_GATE_P2WI);
+
+ sunxi_gpio_set_cfgpin(SUNXI_GPL(0), SUNXI_GPL0_R_P2WI_SCK);
+ sunxi_gpio_set_cfgpin(SUNXI_GPL(1), SUNXI_GPL1_R_P2WI_SDA);
+
+ /* Reset p2wi controller and set clock to CLKIN(12)/8 = 1.5 MHz */
+ writel(P2WI_CTRL_RESET, &p2wi->ctrl);
+ sdelay(0x100);
+ writel(P2WI_CC_SDA_OUT_DELAY(1) | P2WI_CC_CLK_DIV(8),
+ &p2wi->cc);
+}
+
+int p2wi_set_pmu_address(u8 slave_addr, u8 ctrl_reg, u8 init_data)
+{
+ struct sunxi_p2wi_reg *p2wi = (struct sunxi_p2wi_reg *)SUNXI_P2WI_BASE;
+ unsigned long tmo = timer_get_us() + 1000000;
+
+ writel(P2WI_PM_DEV_ADDR(slave_addr) |
+ P2WI_PM_CTRL_ADDR(ctrl_reg) |
+ P2WI_PM_INIT_DATA(init_data) |
+ P2WI_PM_INIT_SEND,
+ &p2wi->pm);
+
+ while ((readl(&p2wi->pm) & P2WI_PM_INIT_SEND)) {
+ if (timer_get_us() > tmo)
+ return -EFAULT;
+ }
+
+ return 0;
+}
+
+static int p2wi_await_trans(void)
+{
+ struct sunxi_p2wi_reg *p2wi = (struct sunxi_p2wi_reg *)SUNXI_P2WI_BASE;
+ unsigned long tmo = timer_get_us() + 1000000;
+ int ret;
+ u8 reg;
+
+ while (1) {
+ reg = readl(&p2wi->status);
+ if (reg & P2WI_STAT_TRANS_ERR) {
+ ret = -EIO;
+ break;
+ }
+ if (reg & P2WI_STAT_TRANS_DONE) {
+ ret = 0;
+ break;
+ }
+ if (timer_get_us() > tmo) {
+ ret = -ETIME;
+ break;
+ }
+ }
+ writel(reg, &p2wi->status); /* Clear status bits */
+ return ret;
+}
+
+int p2wi_read(const u8 addr, u8 *data)
+{
+ struct sunxi_p2wi_reg *p2wi = (struct sunxi_p2wi_reg *)SUNXI_P2WI_BASE;
+ int ret;
+
+ writel(P2WI_DATADDR_BYTE_1(addr), &p2wi->dataddr0);
+ writel(P2WI_DATA_NUM_BYTES(1) |
+ P2WI_DATA_NUM_BYTES_READ, &p2wi->numbytes);
+ writel(P2WI_STAT_TRANS_DONE, &p2wi->status);
+ writel(P2WI_CTRL_TRANS_START, &p2wi->ctrl);
+
+ ret = p2wi_await_trans();
+
+ *data = readl(&p2wi->data0) & P2WI_DATA_BYTE_1_MASK;
+ return ret;
+}
+
+int p2wi_write(const u8 addr, u8 data)
+{
+ struct sunxi_p2wi_reg *p2wi = (struct sunxi_p2wi_reg *)SUNXI_P2WI_BASE;
+
+ writel(P2WI_DATADDR_BYTE_1(addr), &p2wi->dataddr0);
+ writel(P2WI_DATA_BYTE_1(data), &p2wi->data0);
+ writel(P2WI_DATA_NUM_BYTES(1), &p2wi->numbytes);
+ writel(P2WI_STAT_TRANS_DONE, &p2wi->status);
+ writel(P2WI_CTRL_TRANS_START, &p2wi->ctrl);
+
+ return p2wi_await_trans();
+}
diff --git a/arch/arm/include/asm/arch-sunxi/gpio.h b/arch/arm/include/asm/arch-sunxi/gpio.h
index 437dd35..c734cf0 100644
--- a/arch/arm/include/asm/arch-sunxi/gpio.h
+++ b/arch/arm/include/asm/arch-sunxi/gpio.h
@@ -172,6 +172,9 @@ enum sunxi_gpio_number {
#define SUN4I_GPI4_SDC3 2
+#define SUNXI_GPL0_R_P2WI_SCK 3
+#define SUNXI_GPL1_R_P2WI_SDA 3
+
#define SUN8I_GPL2_R_UART_TX 2
#define SUN8I_GPL3_R_UART_RX 2
diff --git a/arch/arm/include/asm/arch-sunxi/p2wi.h b/arch/arm/include/asm/arch-sunxi/p2wi.h
new file mode 100644
index 0000000..1788fa4
--- /dev/null
+++ b/arch/arm/include/asm/arch-sunxi/p2wi.h
@@ -0,0 +1,140 @@
+/*
+ * Sunxi platform Push-Push i2c register definition.
+ *
+ * (c) Copyright 2013 Oliver Schinagl <oliver at schinagl.nl>
+ * http://linux-sunxi.org
+ *
+ * (c)Copyright 2006-2013
+ * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
+ * Berg Xing <bergxing at allwinnertech.com>
+ * Tom Cubie <tangliang at allwinnertech.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _SUNXI_P2WI_H
+#define _SUNXI_P2WI_H
+
+#include <linux/types.h>
+
+#define P2WI_CTRL_RESET (0x1 << 0)
+#define P2WI_CTRL_IRQ_EN (0x1 << 1)
+#define P2WI_CTRL_TRANS_ABORT (0x1 << 6)
+#define P2WI_CTRL_TRANS_START (0x1 << 7)
+
+#define __P2WI_CC_CLK(n) (((n) & 0xff) << 0)
+#define P2WI_CC_CLK_MASK __P2WI_CC_CLK_DIV(0xff)
+#define __P2WI_CC_CLK_DIV(n) (((n) >> 1) - 1)
+#define P2WI_CC_CLK_DIV(n) \
+ __P2WI_CC_CLK(__P2WI_CC_CLK_DIV(n))
+#define P2WI_CC_SDA_OUT_DELAY(n) (((n) & 0x7) << 8)
+#define P2WI_CC_SDA_OUT_DELAY_MASK P2WI_CC_SDA_OUT_DELAY(0x7)
+
+#define P2WI_IRQ_TRANS_DONE (0x1 << 0)
+#define P2WI_IRQ_TRANS_ERR (0x1 << 1)
+#define P2WI_IRQ_LOAD_BUSY (0x1 << 2)
+
+#define P2WI_STAT_TRANS_DONE (0x1 << 0)
+#define P2WI_STAT_TRANS_ERR (0x1 << 1)
+#define P2WI_STAT_LOAD_BUSY (0x1 << 2)
+#define __P2WI_STAT_TRANS_ERR(n) (((n) & 0xff) << 8)
+#define P2WI_STAT_TRANS_ERR_MASK __P2WI_STAT_TRANS_ERR_ID(0xff)
+#define __P2WI_STAT_TRANS_ERR_BYTE_1 0x01
+#define __P2WI_STAT_TRANS_ERR_BYTE_2 0x02
+#define __P2WI_STAT_TRANS_ERR_BYTE_3 0x04
+#define __P2WI_STAT_TRANS_ERR_BYTE_4 0x08
+#define __P2WI_STAT_TRANS_ERR_BYTE_5 0x10
+#define __P2WI_STAT_TRANS_ERR_BYTE_6 0x20
+#define __P2WI_STAT_TRANS_ERR_BYTE_7 0x40
+#define __P2WI_STAT_TRANS_ERR_BYTE_8 0x80
+#define P2WI_STAT_TRANS_ERR_BYTE_1 \
+ __P2WI_STAT_TRANS_ERR(__P2WI_STAT_TRANS_ERR_BYTE_1)
+#define P2WI_STAT_TRANS_ERR_BYTE_2 \
+ __P2WI_STAT_TRANS_ERR(__P2WI_STAT_TRANS_ERR_BYTE_2)
+#define P2WI_STAT_TRANS_ERR_BYTE_3 \
+ __P2WI_STAT_TRANS_ERR(__P2WI_STAT_TRANS_ERR_BYTE_3)
+#define P2WI_STAT_TRANS_ERR_BYTE_4 \
+ __P2WI_STAT_TRANS_ERR(__P2WI_STAT_TRANS_ERR_BYTE_4)
+#define P2WI_STAT_TRANS_ERR_BYTE_5 \
+ __P2WI_STAT_TRANS_ERR(__P2WI_STAT_TRANS_ERR_BYTE_5)
+#define P2WI_STAT_TRANS_ERR_BYTE_6 \
+ __P2WI_STAT_TRANS_ERR(__P2WI_STAT_TRANS_ERR_BYTE_6)
+#define P2WI_STAT_TRANS_ERR_BYTE_7 \
+ __P2WI_STAT_TRANS_ERR(__P2WI_STAT_TRANS_ERR_BYTE_7)
+#define P2WI_STAT_TRANS_ERR_BYTE_8 \
+ __P2WI_STAT_TRANS_ERR(__P2WI_STAT_TRANS_ERR_BYTE_8)
+
+#define P2WI_DATADDR_BYTE_1(n) (((n) & 0xff) << 0)
+#define P2WI_DATADDR_BYTE_1_MASK P2WI_DATADDR_BYTE_1(0xff)
+#define P2WI_DATADDR_BYTE_2(n) (((n) & 0xff) << 8)
+#define P2WI_DATADDR_BYTE_2_MASK P2WI_DATADDR_BYTE_2(0xff)
+#define P2WI_DATADDR_BYTE_3(n) (((n) & 0xff) << 16)
+#define P2WI_DATADDR_BYTE_3_MASK P2WI_DATADDR_BYTE_3(0xff)
+#define P2WI_DATADDR_BYTE_4(n) (((n) & 0xff) << 24)
+#define P2WI_DATADDR_BYTE_4_MASK P2WI_DATADDR_BYTE_4(0xff)
+#define P2WI_DATADDR_BYTE_5(n) (((n) & 0xff) << 0)
+#define P2WI_DATADDR_BYTE_5_MASK P2WI_DATADDR_BYTE_5(0xff)
+#define P2WI_DATADDR_BYTE_6(n) (((n) & 0xff) << 8)
+#define P2WI_DATADDR_BYTE_6_MASK P2WI_DATADDR_BYTE_6(0xff)
+#define P2WI_DATADDR_BYTE_7(n) (((n) & 0xff) << 16)
+#define P2WI_DATADDR_BYTE_7_MASK P2WI_DATADDR_BYTE_7(0xff)
+#define P2WI_DATADDR_BYTE_8(n) (((n) & 0xff) << 24)
+#define P2WI_DATADDR_BYTE_8_MASK P2WI_DATADDR_BYTE_8(0xff)
+
+#define __P2WI_DATA_NUM_BYTES(n) (((n) & 0x7) << 0)
+#define P2WI_DATA_NUM_BYTES_MASK __P2WI_DATA_NUM_BYTES(0x7)
+#define P2WI_DATA_NUM_BYTES(n) __P2WI_DATA_NUM_BYTES((n) - 1)
+#define P2WI_DATA_NUM_BYTES_READ (0x1 << 4)
+
+#define P2WI_DATA_BYTE_1(n) (((n) & 0xff) << 0)
+#define P2WI_DATA_BYTE_1_MASK P2WI_DATA_BYTE_1(0xff)
+#define P2WI_DATA_BYTE_2(n) (((n) & 0xff) << 8)
+#define P2WI_DATA_BYTE_2_MASK P2WI_DATA_BYTE_2(0xff)
+#define P2WI_DATA_BYTE_3(n) (((n) & 0xff) << 16)
+#define P2WI_DATA_BYTE_3_MASK P2WI_DATA_BYTE_3(0xff)
+#define P2WI_DATA_BYTE_4(n) (((n) & 0xff) << 24)
+#define P2WI_DATA_BYTE_4_MASK P2WI_DATA_BYTE_4(0xff)
+#define P2WI_DATA_BYTE_5(n) (((n) & 0xff) << 0)
+#define P2WI_DATA_BYTE_5_MASK P2WI_DATA_BYTE_5(0xff)
+#define P2WI_DATA_BYTE_6(n) (((n) & 0xff) << 8)
+#define P2WI_DATA_BYTE_6_MASK P2WI_DATA_BYTE_6(0xff)
+#define P2WI_DATA_BYTE_7(n) (((n) & 0xff) << 16)
+#define P2WI_DATA_BYTE_7_MASK P2WI_DATA_BYTE_7(0xff)
+#define P2WI_DATA_BYTE_8(n) (((n) & 0xff) << 24)
+#define P2WI_DATA_BYTE_8_MASK P2WI_DATA_BYTE_8(0xff)
+
+#define P2WI_LINECTRL_SDA_CTRL_EN (0x1 << 0)
+#define P2WI_LINECTRL_SDA_OUT_HIGH (0x1 << 1)
+#define P2WI_LINECTRL_SCL_CTRL_EN (0x1 << 2)
+#define P2WI_LINECTRL_SCL_OUT_HIGH (0x1 << 3)
+#define P2WI_LINECTRL_SDA_STATE_HIGH (0x1 << 4)
+#define P2WI_LINECTRL_SCL_STATE_HIGH (0x1 << 5)
+
+#define P2WI_PM_DEV_ADDR(n) (((n) & 0xff) << 0)
+#define P2WI_PM_DEV_ADDR_MASK P2WI_PM_DEV_ADDR(0xff)
+#define P2WI_PM_CTRL_ADDR(n) (((n) & 0xff) << 8)
+#define P2WI_PM_CTRL_ADDR_MASK P2WI_PM_CTRL_ADDR(0xff)
+#define P2WI_PM_INIT_DATA(n) (((n) & 0xff) << 16)
+#define P2WI_PM_INIT_DATA_MASK P2WI_PM_INIT_DATA(0xff)
+#define P2WI_PM_INIT_SEND (0x1 << 31)
+
+struct sunxi_p2wi_reg {
+ u32 ctrl; /* 0x00 control */
+ u32 cc; /* 0x04 clock control */
+ u32 irq; /* 0x08 interrupt */
+ u32 status; /* 0x0c status */
+ u32 dataddr0; /* 0x10 data address 0 */
+ u32 dataddr1; /* 0x14 data address 1 */
+ u32 numbytes; /* 0x18 num bytes */
+ u32 data0; /* 0x1c data buffer 0 */
+ u32 data1; /* 0x20 data buffer 1 */
+ u32 linectrl; /* 0x24 line control */
+ u32 pm; /* 0x28 power management */
+};
+
+void p2wi_init(void);
+int p2wi_set_pmu_address(u8 slave_addr, u8 ctrl_reg, u8 init_data);
+int p2wi_read(const u8 addr, u8 *data);
+int p2wi_write(const u8 addr, u8 data);
+
+#endif /* _SUNXI_P2WI_H */
--
2.1.0
More information about the U-Boot
mailing list