[U-Boot] [PATCH v2 11/11] beagle_x15: add board support for Beagle x15
Felipe Balbi
balbi at ti.com
Thu Nov 6 15:44:27 CET 2014
BeagleBoard-X15 is the next generation Open Source
Hardware BeagleBoard based on TI's AM5728 SoC
featuring dual core 1.5GHZ A15 processor. The
platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x108 at 60),
separate LCD port, video In port, 4GB eMMC, uSD,
Analog audio in/out, dual 1G Ethernet.
For more information, refer to:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
Signed-off-by: Felipe Balbi <balbi at ti.com>
Signed-off-by: Nishanth Menon <nm at ti.com>
---
changes since v1:
new commit log
arch/arm/cpu/armv7/omap5/Kconfig | 4 +
board/ti/beagle_x15/Kconfig | 12 ++
board/ti/beagle_x15/Makefile | 8 +
board/ti/beagle_x15/board.c | 328 ++++++++++++++++++++++++++++++++++++++
board/ti/beagle_x15/mux_data.h | 55 +++++++
configs/beagle_x15_defconfig | 5 +
include/configs/beagle_x15.h | 89 +++++++++++
include/configs/ti_omap5_common.h | 2 +
8 files changed, 503 insertions(+)
create mode 100644 board/ti/beagle_x15/Kconfig
create mode 100644 board/ti/beagle_x15/Makefile
create mode 100644 board/ti/beagle_x15/board.c
create mode 100644 board/ti/beagle_x15/mux_data.h
create mode 100644 configs/beagle_x15_defconfig
create mode 100644 include/configs/beagle_x15.h
diff --git a/arch/arm/cpu/armv7/omap5/Kconfig b/arch/arm/cpu/armv7/omap5/Kconfig
index 129982c..aca862d 100644
--- a/arch/arm/cpu/armv7/omap5/Kconfig
+++ b/arch/arm/cpu/armv7/omap5/Kconfig
@@ -12,6 +12,9 @@ config TARGET_OMAP5_UEVM
config TARGET_DRA7XX_EVM
bool "TI DRA7XX"
+config TARGET_BEAGLE_X15
+ bool "BeagleBoard X15"
+
endchoice
config SYS_SOC
@@ -20,5 +23,6 @@ config SYS_SOC
source "board/compulab/cm_t54/Kconfig"
source "board/ti/omap5_uevm/Kconfig"
source "board/ti/dra7xx/Kconfig"
+source "board/ti/beagle_x15/Kconfig"
endif
diff --git a/board/ti/beagle_x15/Kconfig b/board/ti/beagle_x15/Kconfig
new file mode 100644
index 0000000..a305ff1
--- /dev/null
+++ b/board/ti/beagle_x15/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_BEAGLE_X15
+
+config SYS_BOARD
+ default "beagle_x15"
+
+config SYS_VENDOR
+ default "ti"
+
+config SYS_CONFIG_NAME
+ default "beagle_x15"
+
+endif
diff --git a/board/ti/beagle_x15/Makefile b/board/ti/beagle_x15/Makefile
new file mode 100644
index 0000000..5cd6873
--- /dev/null
+++ b/board/ti/beagle_x15/Makefile
@@ -0,0 +1,8 @@
+#
+# (C) Copyright 2014
+# Texas Instruments, <www.ti.com>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := board.o
diff --git a/board/ti/beagle_x15/board.c b/board/ti/beagle_x15/board.c
new file mode 100644
index 0000000..5cafc87
--- /dev/null
+++ b/board/ti/beagle_x15/board.c
@@ -0,0 +1,328 @@
+/*
+ * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com
+ *
+ * Author: Felipe Balbi <balbi at ti.com>
+ *
+ * Based on board/ti/dra7xx/evm.c
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <palmas.h>
+#include <sata.h>
+#include <usb.h>
+#include <asm/omap_common.h>
+#include <asm/emif.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/sata.h>
+#include <asm/arch/gpio.h>
+#include <environment.h>
+
+#include "mux_data.h"
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+#include <cpsw.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+const struct omap_sysinfo sysinfo = {
+ "Board: BeagleBoard x15\n"
+};
+
+static const struct dmm_lisa_map_regs beagle_x15_lisa_regs = {
+ .dmm_lisa_map_3 = 0x80740300,
+ .is_ma_present = 0x1
+};
+
+void emif_get_dmm_regs(const struct dmm_lisa_map_regs **dmm_lisa_regs)
+{
+ *dmm_lisa_regs = &beagle_x15_lisa_regs;
+}
+
+static const struct emif_regs beagle_x15_ddr3_532mhz_emif_regs = {
+ .sdram_config_init = 0x61851B32, /* dont know what to do about this */
+ .sdram_config = 0x61851B32,
+ .sdram_config2 = 0x00000000,
+ .ref_ctrl = 0x00001035,
+ .sdram_tim1 = 0xCEEF266B,
+ .sdram_tim2 = 0x328F7FDA,
+ .sdram_tim3 = 0x027F88A8,
+ .read_idle_ctrl = 0x00050001, /* not sure where in gel file */
+ .zq_config = 0x0007190B,
+ .temp_alert_config = 0x00000000,
+ .emif_ddr_phy_ctlr_1_init = 0x0E24400A, /* not sure what to do about this */
+ .emif_ddr_phy_ctlr_1 = 0x0E24400A, /* based on non hw level enabled */
+ .emif_ddr_ext_phy_ctrl_1 = 0x10040100, /* not sure wherein gel file */
+ .emif_ddr_ext_phy_ctrl_2 = 0x00740074,
+ .emif_ddr_ext_phy_ctrl_3 = 0x00780078,
+ .emif_ddr_ext_phy_ctrl_4 = 0x007c007c,
+ .emif_ddr_ext_phy_ctrl_5 = 0x007b007b,
+ .emif_rd_wr_lvl_rmp_win = 0x00000000,
+ .emif_rd_wr_lvl_rmp_ctl = 0x00000000, /* based on non hw level enabled */
+ .emif_rd_wr_lvl_ctl = 0x00000000, /* not sure where based in gel file */
+ .emif_rd_wr_exec_thresh = 0x00000305
+};
+
+void emif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs)
+{
+ *regs = &beagle_x15_ddr3_532mhz_emif_regs;
+}
+
+static const u32 beagle_x15_ddr3_ext_phy_ctrl_const_regs[] = {
+ 0x00800080, // 6
+
+
+ 0x00360036, // 7
+ 0x00340034, // 8
+ 0x00360036, // 9
+ 0x00350035, // 10
+ 0x00350035, // 11
+
+ 0x01ff01ff, // 12
+ 0x01ff01ff,
+ 0x01ff01ff,
+ 0x01ff01ff,
+ 0x01ff01ff,
+
+ 0x00430043,
+ 0x003e003e,
+ 0x004a004a,
+ 0x00470047,
+ 0x00400040,
+
+ 0x00000000,
+ 0x00600020,
+ 0x40010080,
+ 0x08102040,
+
+ 0x00400040,
+ 0x00400040,
+ 0x00400040,
+ 0x00400040,
+ 0x00400040
+};
+
+void emif_get_ext_phy_ctrl_const_regs(u32 emif_nr, const u32 **regs, u32 *size)
+{
+ *regs = beagle_x15_ddr3_ext_phy_ctrl_const_regs;
+ *size = ARRAY_SIZE(beagle_x15_ddr3_ext_phy_ctrl_const_regs);
+}
+
+struct vcores_data beagle_x15_volts = {
+ .mpu.value = VDD_MPU_DRA752,
+ .mpu.efuse.reg = STD_FUSE_OPP_VMIN_MPU_NOM,
+ .mpu.efuse.reg_bits = DRA752_EFUSE_REGBITS,
+ .mpu.addr = TPS659038_REG_ADDR_SMPS12,
+ .mpu.pmic = &tps659038,
+
+ .eve.value = VDD_EVE_DRA752,
+ .eve.efuse.reg = STD_FUSE_OPP_VMIN_DSPEVE_NOM,
+ .eve.efuse.reg_bits = DRA752_EFUSE_REGBITS,
+ .eve.addr = TPS659038_REG_ADDR_SMPS45,
+ .eve.pmic = &tps659038,
+
+ .gpu.value = VDD_GPU_DRA752,
+ .gpu.efuse.reg = STD_FUSE_OPP_VMIN_GPU_NOM,
+ .gpu.efuse.reg_bits = DRA752_EFUSE_REGBITS,
+ .gpu.addr = TPS659038_REG_ADDR_SMPS45,
+ .gpu.pmic = &tps659038,
+
+ .core.value = VDD_CORE_DRA752,
+ .core.efuse.reg = STD_FUSE_OPP_VMIN_CORE_NOM,
+ .core.efuse.reg_bits = DRA752_EFUSE_REGBITS,
+ .core.addr = TPS659038_REG_ADDR_SMPS6,
+ .core.pmic = &tps659038,
+
+ .iva.value = VDD_IVA_DRA752,
+ .iva.efuse.reg = STD_FUSE_OPP_VMIN_IVA_NOM,
+ .iva.efuse.reg_bits = DRA752_EFUSE_REGBITS,
+ .iva.addr = TPS659038_REG_ADDR_SMPS45,
+ .iva.pmic = &tps659038,
+};
+
+void hw_data_init(void)
+{
+ *prcm = &dra7xx_prcm;
+ *dplls_data = &dra7xx_dplls;
+ *omap_vcores = &beagle_x15_volts;
+ *ctrl = &dra7xx_ctrl;
+}
+
+int board_init(void)
+{
+ gpmc_init();
+ gd->bd->bi_boot_params = (CONFIG_SYS_SDRAM_BASE + 0x100);
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+ init_sata(0);
+ /*
+ * DEV_CTRL.DEV_ON = 1 please - else palmas switches off in 8 seconds
+ * This is the POWERHOLD-in-Low behavior.
+ */
+ palmas_i2c_write_u8(TPS65903X_CHIP_P1, 0xA0, 0x1);
+ return 0;
+}
+
+static void do_set_mux32(u32 base,
+ struct pad_conf_entry const *array, int size)
+{
+ int i;
+ struct pad_conf_entry *pad = (struct pad_conf_entry *)array;
+
+ for (i = 0; i < size; i++, pad++)
+ writel(pad->val, base + pad->offset);
+}
+
+void set_muxconf_regs_essential(void)
+{
+ do_set_mux32((*ctrl)->control_padconf_core_base,
+ core_padconf_array_essential,
+ sizeof(core_padconf_array_essential) /
+ sizeof(struct pad_conf_entry));
+}
+
+#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC)
+int board_mmc_init(bd_t *bis)
+{
+ omap_mmc_init(0, 0, 0, -1, -1);
+ omap_mmc_init(1, 0, 0, -1, -1);
+ return 0;
+}
+#endif
+
+#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_OS_BOOT)
+int spl_start_uboot(void)
+{
+ /* break into full u-boot on 'c' */
+ if (serial_tstc() && serial_getc() == 'c')
+ return 1;
+
+#ifdef CONFIG_SPL_ENV_SUPPORT
+ env_init();
+ env_relocate_spec();
+ if (getenv_yesno("boot_os") != 1)
+ return 1;
+#endif
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+
+/* Delay value to add to calibrated value */
+#define RGMII0_TXCTL_DLY_VAL ((0x3 << 5) + 0x8)
+#define RGMII0_TXD0_DLY_VAL ((0x3 << 5) + 0x8)
+#define RGMII0_TXD1_DLY_VAL ((0x3 << 5) + 0x2)
+#define RGMII0_TXD2_DLY_VAL ((0x4 << 5) + 0x0)
+#define RGMII0_TXD3_DLY_VAL ((0x4 << 5) + 0x0)
+#define VIN2A_D13_DLY_VAL ((0x3 << 5) + 0x8)
+#define VIN2A_D17_DLY_VAL ((0x3 << 5) + 0x8)
+#define VIN2A_D16_DLY_VAL ((0x3 << 5) + 0x2)
+#define VIN2A_D15_DLY_VAL ((0x4 << 5) + 0x0)
+#define VIN2A_D14_DLY_VAL ((0x4 << 5) + 0x0)
+
+static void cpsw_control(int enabled)
+{
+ /* VTP can be added here */
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+ {
+ .slave_reg_ofs = 0x208,
+ .sliver_reg_ofs = 0xd80,
+ .phy_addr = 1,
+ },
+ {
+ .slave_reg_ofs = 0x308,
+ .sliver_reg_ofs = 0xdc0,
+ .phy_addr = 2,
+ },
+};
+
+static struct cpsw_platform_data cpsw_data = {
+ .mdio_base = CPSW_MDIO_BASE,
+ .cpsw_base = CPSW_BASE,
+ .mdio_div = 0xff,
+ .channels = 8,
+ .cpdma_reg_ofs = 0x800,
+ .slaves = 1,
+ .slave_data = cpsw_slaves,
+ .ale_reg_ofs = 0xd00,
+ .ale_entries = 1024,
+ .host_port_reg_ofs = 0x108,
+ .hw_stats_reg_ofs = 0x900,
+ .bd_ram_ofs = 0x2000,
+ .mac_control = (1 << 5),
+ .control = cpsw_control,
+ .host_port_num = 0,
+ .version = CPSW_CTRL_VERSION_2,
+};
+
+int board_eth_init(bd_t *bis)
+{
+ int ret;
+ uint8_t mac_addr[6];
+ uint32_t mac_hi, mac_lo;
+ uint32_t ctrl_val;
+
+ /* try reading mac address from efuse */
+ mac_lo = readl((*ctrl)->control_core_mac_id_0_lo);
+ mac_hi = readl((*ctrl)->control_core_mac_id_0_hi);
+ mac_addr[0] = (mac_hi & 0xFF0000) >> 16;
+ mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+ mac_addr[2] = mac_hi & 0xFF;
+ mac_addr[3] = (mac_lo & 0xFF0000) >> 16;
+ mac_addr[4] = (mac_lo & 0xFF00) >> 8;
+ mac_addr[5] = mac_lo & 0xFF;
+
+ if (!getenv("ethaddr")) {
+ printf("<ethaddr> not set. Validating first E-fuse MAC\n");
+
+ if (is_valid_ether_addr(mac_addr))
+ eth_setenv_enetaddr("ethaddr", mac_addr);
+ }
+
+ mac_lo = readl((*ctrl)->control_core_mac_id_1_lo);
+ mac_hi = readl((*ctrl)->control_core_mac_id_1_hi);
+ mac_addr[0] = (mac_hi & 0xFF0000) >> 16;
+ mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+ mac_addr[2] = mac_hi & 0xFF;
+ mac_addr[3] = (mac_lo & 0xFF0000) >> 16;
+ mac_addr[4] = (mac_lo & 0xFF00) >> 8;
+ mac_addr[5] = mac_lo & 0xFF;
+
+ if (!getenv("eth1addr")) {
+ if (is_valid_ether_addr(mac_addr))
+ eth_setenv_enetaddr("eth1addr", mac_addr);
+ }
+
+ ctrl_val = readl((*ctrl)->control_core_control_io1) & (~0x33);
+ ctrl_val |= 0x22;
+ writel(ctrl_val, (*ctrl)->control_core_control_io1);
+
+ ret = cpsw_register(&cpsw_data);
+ if (ret < 0)
+ printf("Error %d registering CPSW switch\n", ret);
+
+ return ret;
+}
+#endif
+
+#ifdef CONFIG_USB_XHCI_OMAP
+int board_usb_init(int index, enum usb_init_type init)
+{
+ setbits_le32((*prcm)->cm_l3init_usb_otg_ss_clkctrl,
+ OTG_SS_CLKCTRL_MODULEMODE_HW | OPTFCLKEN_REFCLK960M);
+
+ return 0;
+}
+#endif
diff --git a/board/ti/beagle_x15/mux_data.h b/board/ti/beagle_x15/mux_data.h
new file mode 100644
index 0000000..2294abe
--- /dev/null
+++ b/board/ti/beagle_x15/mux_data.h
@@ -0,0 +1,55 @@
+/*
+ * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com
+ *
+ * Author: Felipe Balbi <balbi at ti.com>
+ *
+ * Based on board/ti/dra7xx/evm.c
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#ifndef _MUX_DATA_BEAGLE_X15_H_
+#define _MUX_DATA_BEAGLE_X15_H_
+
+#include <asm/arch/mux_dra7xx.h>
+
+const struct pad_conf_entry core_padconf_array_essential[] = {
+ {MMC1_CLK, (IEN | PTU | PDIS | M0)}, /* MMC1_CLK */
+ {MMC1_CMD, (IEN | PTU | PDIS | M0)}, /* MMC1_CMD */
+ {MMC1_DAT0, (IEN | PTU | PDIS | M0)}, /* MMC1_DAT0 */
+ {MMC1_DAT1, (IEN | PTU | PDIS | M0)}, /* MMC1_DAT1 */
+ {MMC1_DAT2, (IEN | PTU | PDIS | M0)}, /* MMC1_DAT2 */
+ {MMC1_DAT3, (IEN | PTU | PDIS | M0)}, /* MMC1_DAT3 */
+ {MMC1_SDCD, (FSC | IEN | PTU | PDIS | M0)}, /* MMC1_SDCD */
+ {MMC1_SDWP, (FSC | IEN | PTD | PEN | M14)}, /* MMC1_SDWP */
+ {GPMC_A19, (IEN | PTU | PDIS | M1)}, /* mmc2_dat4 */
+ {GPMC_A20, (IEN | PTU | PDIS | M1)}, /* mmc2_dat5 */
+ {GPMC_A21, (IEN | PTU | PDIS | M1)}, /* mmc2_dat6 */
+ {GPMC_A22, (IEN | PTU | PDIS | M1)}, /* mmc2_dat7 */
+ {GPMC_A23, (IEN | PTU | PDIS | M1)}, /* mmc2_clk */
+ {GPMC_A24, (IEN | PTU | PDIS | M1)}, /* mmc2_dat0 */
+ {GPMC_A25, (IEN | PTU | PDIS | M1)}, /* mmc2_dat1 */
+ {GPMC_A26, (IEN | PTU | PDIS | M1)}, /* mmc2_dat2 */
+ {GPMC_A27, (IEN | PTU | PDIS | M1)}, /* mmc2_dat3 */
+ {GPMC_CS1, (IEN | PTU | PDIS | M1)}, /* mmm2_cmd */
+ {UART3_RXD, (FSC | IEN | PTU | PDIS | M0)}, /* UART3_RXD */
+ {UART3_TXD, (FSC | IEN | PTU | PDIS | M0)}, /* UART3_TXD */
+ {I2C1_SDA, (IEN | PTU | PDIS | M0)}, /* I2C1_SDA */
+ {I2C1_SCL, (IEN | PTU | PDIS | M0)}, /* I2C1_SCL */
+ {MDIO_MCLK, (PTU | PEN | M0)}, /* MDIO_MCLK */
+ {MDIO_D, (IEN | PTU | PEN | M0)}, /* MDIO_D */
+ {RGMII0_TXC, (M0) },
+ {RGMII0_TXCTL, (M0) },
+ {RGMII0_TXD3, (M0) },
+ {RGMII0_TXD2, (M0) },
+ {RGMII0_TXD1, (M0) },
+ {RGMII0_TXD0, (M0) },
+ {RGMII0_RXC, (IEN | M0) },
+ {RGMII0_RXCTL, (IEN | M0) },
+ {RGMII0_RXD3, (IEN | M0) },
+ {RGMII0_RXD2, (IEN | M0) },
+ {RGMII0_RXD1, (IEN | M0) },
+ {RGMII0_RXD0, (IEN | M0) },
+ {USB1_DRVVBUS, (M0 | FSC) },
+ {SPI1_CS1, (PEN | IDIS | M14) }, /* GPIO7_11 */
+};
+#endif /* _MUX_DATA_BEAGLE_X15_H_ */
diff --git a/configs/beagle_x15_defconfig b/configs/beagle_x15_defconfig
new file mode 100644
index 0000000..872ab63
--- /dev/null
+++ b/configs/beagle_x15_defconfig
@@ -0,0 +1,5 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=3"
++S:CONFIG_ARM=y
++S:CONFIG_OMAP54XX=y
++S:CONFIG_TARGET_BEAGLE_X15=y
diff --git a/include/configs/beagle_x15.h b/include/configs/beagle_x15.h
new file mode 100644
index 0000000..2009f5a
--- /dev/null
+++ b/include/configs/beagle_x15.h
@@ -0,0 +1,89 @@
+/*
+ * (C) Copyright 2014
+ * Texas Instruments Incorporated.
+ * Felipe Balbi <balbi at ti.com>
+ *
+ * Configuration settings for the TI Beagle x15 board.
+ * See ti_omap5_common.h for omap5 common settings.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_BEAGLE_X15_H
+#define __CONFIG_BEAGLE_X15_H
+
+#define CONFIG_AM57XX
+
+#define CONFIG_SYS_SDRAM_BASE 0x80000000
+#define CONFIG_NR_DRAM_BANKS 2
+
+#define CONFIG_ENV_SIZE (64 << 10)
+#define CONFIG_ENV_IS_IN_FAT
+#define FAT_ENV_INTERFACE "mmc"
+#define FAT_ENV_DEVICE_AND_PART "0:1"
+#define FAT_ENV_FILE "uboot.env"
+
+#define CONFIG_CMD_SAVEENV
+
+#define CONSOLEDEV "ttyO2"
+#define CONFIG_SYS_NS16550_COM1 UART1_BASE /* Base EVM has UART0 */
+#define CONFIG_SYS_NS16550_COM2 UART2_BASE /* UART2 */
+#define CONFIG_SYS_NS16550_COM3 UART3_BASE /* UART3 */
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_SYS_OMAP_ABE_SYSCK
+
+/* Define the default GPT table for eMMC */
+#define PARTS_DEFAULT \
+ "uuid_disk=${uuid_gpt_disk};" \
+ "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}"
+
+#include <configs/ti_omap5_common.h>
+
+/* Enhance our eMMC support / experience. */
+#define CONFIG_CMD_GPT
+#define CONFIG_EFI_PARTITION
+#define CONFIG_PARTITION_UUIDS
+#define CONFIG_CMD_PART
+
+/* CPSW Ethernet */
+#define CONFIG_CMD_NET /* 'bootp' and 'tftp' */
+#define CONFIG_CMD_DHCP
+#define CONFIG_BOOTP_DNS /* Configurable parts of CMD_DHCP */
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_NET_RETRY_COUNT 10
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_MII
+#define CONFIG_DRIVER_TI_CPSW /* Driver for IP block */
+#define CONFIG_MII /* Required in net/eth.c */
+#define CONFIG_PHY_GIGE /* per-board part of CPSW */
+#define CONFIG_PHYLIB
+
+#define CONFIG_SUPPORT_EMMC_BOOT
+
+/* USB xHCI HOST */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_HOST
+#define CONFIG_USB_XHCI
+#define CONFIG_USB_XHCI_OMAP
+#define CONFIG_USB_STORAGE
+#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
+
+#define CONFIG_OMAP_USB_PHY
+#define CONFIG_OMAP_USB3PHY1_HOST
+
+/* SATA */
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_CMD_SCSI
+#define CONFIG_LIBATA
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+ CONFIG_SYS_SCSI_MAX_LUN)
+
+#endif /* __CONFIG_BEAGLE_X5_H */
diff --git a/include/configs/ti_omap5_common.h b/include/configs/ti_omap5_common.h
index de96d7d..c47651d 100644
--- a/include/configs/ti_omap5_common.h
+++ b/include/configs/ti_omap5_common.h
@@ -117,6 +117,8 @@
"setenv fdtfile dra7-evm.dtb; fi;" \
"if test $board_name = dra72x; then " \
"setenv fdtfile dra72-evm.dtb; fi;" \
+ "if test $board_name = beagle_x15; then " \
+ "setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
"if test $fdtfile = undefined; then " \
"echo WARNING: Could not determine device tree to use; fi; \0" \
"loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile};\0" \
--
2.1.0.GIT
More information about the U-Boot
mailing list