[U-Boot] [PATCH 4/5] usb: s3c-otg: Allow custom gusbcfg
Lukasz Majewski
l.majewski at samsung.com
Fri Nov 7 15:33:10 CET 2014
Hi Marek,
> On Friday, November 07, 2014 at 10:11:35 AM, Lukasz Majewski wrote:
> > Hi Marek,
> >
> > > On Tuesday, November 04, 2014 at 08:36:57 PM, Pavel Machek wrote:
> > > > On Tue 2014-11-04 06:07:33, Marek Vasut wrote:
> > > > > Allow passing in a custom configuration of the gusbcfg
> > > > > register via platform data.
> > > > >
> > > > > Signed-off-by: Marek Vasut <marex at denx.de>
> > > > > Cc: Chin Liang See <clsee at altera.com>
> > > > > Cc: Dinh Nguyen <dinguyen at opensource.altera.com>
> > > > > Cc: Vince Bridgers <vbridger at altera.com>
> > > >
> > > > Acked-by: Pavel Machek <pavel at denx.de>
> > > >
> > > > > debug("Reseting OTG controller\n");
> > > > >
> > > > > - writel(0<<15 /* PHY Low Power Clock
> > > > > sel*/
> > > > > + dflt_gusbcfg =
> > > > > + 0<<15 /* PHY Low Power Clock
> > > > > sel*/
> > > > >
> > > > > |1<<14 /* Non-Periodic TxFIFO
> > > > >
> > > > > Rewind Enable*/ |0x5<<10 /* Turnaround time*/
> > > > >
> > > > > |0<<9 | 0<<8 /* [0:HNP disable,1:HNP
> > > > >
> > > > > enable][ 0:SRP disable*/
> > > > >
> > > > > @@ -413,8 +415,12 @@ static void reconfig_usbd(void)
> > > > >
> > > > > |0<<6 /* 0: high speed utmi+,
> > > > > 1: full speed serial*/ |0<<4 /* 0: utmi+,
> > > > > 1:ulpi*/
> > > > >
> > > > > |1<<3 /* phy i/f 0:8bit,
> > > > >
> > > > > 1:16bit*/
> > > > >
> > > > > - |0x7<<0, /* HS/FS Timeout**/
> > > > > - ®->gusbcfg);
> > > > > + |0x7<<0; /* HS/FS Timeout**/
> > > > > +
> > > >
> > > > "Interesting" comment style. And I'd remove 0x prefixes from
> > > > constants <8...
> > >
> > > Lukasz, what do you say to just convert those four boards to use
> > > the gusbcfg platform data afterward ?
> >
> > +1
> >
> > It is a very good idea since we are using the same dwc2 IP block for
> > host (./usb/host/dwc2.c) and device (s3c_hsotg).
>
> Yep ... I'm just wondering if we should do that rename in the next MW.
> If you're fine with this MW though, then I will do just that.
>
> > > btw. you can find the latest version in u-boot-usb:topic/s3c-otg
> >
> > I've read comments from Pavel and tested the code up till first
> > build error :-).
>
> I rewrote that branch, so feel free to use that as a base for your
> testing. I will repost the corrected patches once I get feedback from
> you.
>
> Best regards,
> Marek Vasut
Reviewed-by: Lukasz Majewski <l.majewski at samsung.com>
Tested-by: Lukasz Majewski <l.majewski at samsung.com>
Test HW: Trats2 (Exynos4412)
--
Best regards,
Lukasz Majewski
Samsung R&D Institute Poland (SRPOL) | Linux Platform Group
More information about the U-Boot
mailing list