[U-Boot] [PATCH v3 7/8] imx6: SPL support for iMX6 SabreSD
John Tobias
john.tobias.ph at gmail.com
Mon Nov 10 01:23:30 CET 2014
Hi Stefano,
On Sun, Nov 9, 2014 at 1:16 PM, Stefano Babic <sbabic at denx.de> wrote:
> Hi John,
>
> On 08/11/2014 22:27, John Tobias wrote:
>> This patch will enable the support for SPL on iMX6 SabreSD.
>> It tested on SD2 and SD3 mmc port.
>> ---
>> board/freescale/mx6sabresd/mx6sabresd.c | 211 +++++++++++++++++++++++++++++++-
>> 1 file changed, 209 insertions(+), 2 deletions(-)
>>
>> diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
>> index 3d81fff..f443337 100644
>> --- a/board/freescale/mx6sabresd/mx6sabresd.c
>> +++ b/board/freescale/mx6sabresd/mx6sabresd.c
>> @@ -55,8 +55,7 @@ DECLARE_GLOBAL_DATA_PTR;
>>
>> int dram_init(void)
>> {
>> - gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
>> -
>> + gd->ram_size = imx_ddr_size();
>> return 0;
>> }
>>
>> @@ -607,3 +606,211 @@ int checkboard(void)
>> puts("Board: MX6-SabreSD\n");
>> return 0;
>> }
>> +
>> +#ifdef CONFIG_SPL_BUILD
>> +#include <spl.h>
>> +#include <libfdt.h>
>> +
>> +#define BOOT_CFG 0x20D8004
>> +#define __REG(x) (*((volatile u32 *)(x)))
>> +
>> +struct fsl_esdhc_cfg spl_usdhc_cfg;
>> +/*
>> + * Got it from mx6q_4x_mt41j128.cfg file
>> + */
>> +void set_mt41j128_ddr(void)
>> +{
>> + __REG(0x020e05a8) = 0x00000028;
>> + __REG(0x020e05b0) = 0x00000028;
>> + __REG(0x020e0524) = 0x00000028;
>> + __REG(0x020e051c) = 0x00000028;
>> +
>> + __REG(0x020e0518) = 0x00000028;
>> + __REG(0x020e050c) = 0x00000028;
>> + __REG(0x020e05b8) = 0x00000028;
>> + __REG(0x020e05c0) = 0x00000028;
>> +
>> + __REG(0x020e05ac) = 0x00000028;
>> + __REG(0x020e05b4) = 0x00000028;
>> + __REG(0x020e0528) = 0x00000028;
>> + __REG(0x020e0520) = 0x00000028;
>> +
>> + __REG(0x020e0514) = 0x00000028;
>> + __REG(0x020e0510) = 0x00000028;
>> + __REG(0x020e05bc) = 0x00000028;
>> + __REG(0x020e05c4) = 0x00000028;
>> +
>> + __REG(0x020e056c) = 0x00000030;
>> + __REG(0x020e0578) = 0x00000030;
>> + __REG(0x020e0588) = 0x00000030;
>> + __REG(0x020e0594) = 0x00000030;
>> +
>> + __REG(0x020e057c) = 0x00000030;
>> + __REG(0x020e0590) = 0x00000030;
>> + __REG(0x020e0598) = 0x00000030;
>> + __REG(0x020e058c) = 0x00000000;
>> +
>> + __REG(0x020e059c) = 0x00003030;
>> + __REG(0x020e05a0) = 0x00003030;
>> + __REG(0x020e0784) = 0x00000028;
>> + __REG(0x020e0788) = 0x00000028;
>> +
>> + __REG(0x020e0794) = 0x00000028;
>> + __REG(0x020e079c) = 0x00000028;
>> + __REG(0x020e07a0) = 0x00000028;
>> + __REG(0x020e07a4) = 0x00000028;
>> +
>> + __REG(0x020e07a8) = 0x00000028;
>> + __REG(0x020e0748) = 0x00000028;
>> + __REG(0x020e074c) = 0x00000030;
>> + __REG(0x020e0750) = 0x00020000;
>> +
>> + __REG(0x020e0758) = 0x00000000;
>> + __REG(0x020e0774) = 0x00020000;
>> + __REG(0x020e078c) = 0x00000030;
>> + __REG(0x020e0798) = 0x000C0000;
>> +
>> + __REG(0x021b081c) = 0x33333333;
>> + __REG(0x021b0820) = 0x33333333;
>> + __REG(0x021b0824) = 0x33333333;
>> + __REG(0x021b0828) = 0x33333333;
>> +
>> + __REG(0x021b481c) = 0x33333333;
>> + __REG(0x021b4820) = 0x33333333;
>> + __REG(0x021b4824) = 0x33333333;
>> + __REG(0x021b4828) = 0x33333333;
>> +
>> + __REG(0x021b0018) = 0x00001740;
>> +
>> + __REG(0x021b001c) = 0x00008000;
>> + __REG(0x021b000c) = 0x8A8F7975;
>> + __REG(0x021b0010) = 0xFF538E64;
>> + __REG(0x021b0014) = 0x01FF00DB;
>> + __REG(0x021b002c) = 0x000026D2;
>> +
>> + __REG(0x021b0030) = 0x008F0E21;
>> + __REG(0x021b0008) = 0x09444040;
>> + __REG(0x021b0004) = 0x00020036;
>> + __REG(0x021b0040) = 0x00000047;
>> + __REG(0x021b0000) = 0x841A0000;
>> +
>> + __REG(0x021b001c) = 0x04088032;
>> + __REG(0x021b001c) = 0x00008033;
>> + __REG(0x021b001c) = 0x00428031;
>> + __REG(0x021b001c) = 0x09408030;
>> +
>> + __REG(0x021b001c) = 0x04008040;
>> + __REG(0x021b0800) = 0xA1380003;
>> + __REG(0x021b0020) = 0x00005800;
>> + __REG(0x021b0818) = 0x00000007;
>> + __REG(0x021b4818) = 0x00000007;
>> +
>> + /* Calibration values based on ARD and 528MHz */
>> + __REG(0x021b083c) = 0x434B0358;
>> + __REG(0x021b0840) = 0x033D033C;
>> + __REG(0x021b483c) = 0x03520362;
>> + __REG(0x021b4840) = 0x03480318;
>> + __REG(0x021b0848) = 0x41383A3C;
>> + __REG(0x021b4848) = 0x3F3C374A;
>> + __REG(0x021b0850) = 0x42434444;
>> + __REG(0x021b4850) = 0x4932473A;
>> +
>> + __REG(0x021b080c) = 0x001F001F;
>> + __REG(0x021b0810) = 0x001F001F;
>> +
>> + __REG(0x021b480c) = 0x001F001F;
>> + __REG(0x021b4810) = 0x001F001F;
>> +
>> + __REG(0x021b08b8) = 0x00000800;
>> + __REG(0x021b48b8) = 0x00000800;
>> +
>> + __REG(0x021b0404) = 0x00011006;
>> + __REG(0x021b0004) = 0x00025576;
>> +
>> + __REG(0x021b001c) = 0x00000000;
>> +
>> + __REG(0x020c4068) = 0x00C03F3F;
>> + __REG(0x020c406c) = 0x0030FC00;
>> + __REG(0x020c4070) = 0x0FFFC000;
>> + __REG(0x020c4074) = 0x3FF00000;
>> + __REG(0x020c4078) = 0x00FFF300;
>> + __REG(0x020c407c) = 0x0F0000C3;
>> + __REG(0x020c4080) = 0x000003FF;
>> +}
>> +
>
> This cannot be accepted. Firstly, you cannot use fixed offset. The code
> you propose here is very difficult to maintain.
>
> Then, please take a look at the i.MX6 boards that are already supporting
> SPL (ventana and novena). There is a logical separation between iomux,
> calibration, and so on. You have to provide tables, and you should then
> call the common functions:
>
> mx6dq_dram_iocfg();
> mx6_dram_cfg();
The reason why I did not use the two functions you've mentioned is that the
contents of mx6q_4x_mt41j128.cfg are very difficult to convert according to the
data structures being required by the two functions above.
It's barely plain text and it requires a lot of time to look for the
register address
name it the datasheet.
>
> Again, please take a look at the boards I mentioned.
>
>> +/*
>> + * This section require the differentiation
>> + * between iMX6 Sabre Families.
>> + * But for now, it will configure only for
>> + * SabreSD.
>> + */
>> +static void spl_dram_init(void)
>> +{
>> + set_mt41j128_ddr();
>> +}
>> +
>> +int spl_board_mmc_init(bd_t *bis)
>> +{
>> + unsigned reg = readl(BOOT_CFG);
>> + /*
>> + * Upon reading BOOT_CFG register the following map is done:
>> + * (U-boot device node) (Physical Port)
>> + * 0x840 SD2
>> + * 0x1040 SD3
>> + * 0x1840 eMMC
>> + */
>
> You add a new entry point here (spl_board_mmc_init), but why cannot you
> do this in the functions already supplied by SPL ? Why not in board_init_f ?
When the spl_mmc_load_image function being called, it call
mmc_initialize. By default, the mmc_initialize
call board_mmc_init. By looking the said function, it initialize all mmc ports.
While, in spl_board_mmc_init, only initialize the current mmc port.
>
>> + switch (reg) {
>> + case 0x840:
>> + imx_iomux_v3_setup_multiple_pads(
>> + usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
>> + spl_usdhc_cfg.esdhc_base = USDHC2_BASE_ADDR;
>> + spl_usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
>> + gd->arch.sdhc_clk = spl_usdhc_cfg.sdhc_clk;
>> + break;
>> + case 0x1040:
>> + imx_iomux_v3_setup_multiple_pads(
>> + usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
>> + spl_usdhc_cfg.esdhc_base = USDHC3_BASE_ADDR;
>> + spl_usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
>> + gd->arch.sdhc_clk = spl_usdhc_cfg.sdhc_clk;
>> + break;
>> + case 0x1840:
>> + imx_iomux_v3_setup_multiple_pads(
>> + usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
>> + spl_usdhc_cfg.esdhc_base = USDHC4_BASE_ADDR;
>> + spl_usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
>> + gd->arch.sdhc_clk = spl_usdhc_cfg.sdhc_clk;
>> + break;
>> + }
>> +
>> + return fsl_esdhc_initialize(bis, &spl_usdhc_cfg);
>> +}
>> +
>> +void board_init_f(ulong dummy)
>> +{
>> + /* setup AIPS and disable watchdog */
>> + arch_cpu_init();
>> +
>> + /* iomux and setup of i2c */
>> + board_early_init_f();
>
> ??
>
> A "early" function is generally called by common code at a different
> point. It makes no sense to call it inside board_init_f()
>
>> +
>> + /* setup GP timer */
>> + timer_init();
>> +
>
> Then I am expecting iomux setuup---
The iomux setup being called in board_early_init_f...
>
>> + /* UART clocks enabled and gd valid - init serial console */
>> + preloader_console_init();
>> +
>> + /* DDR initialization */
>> + spl_dram_init();
>
> and here calling the already supplied functions.
>
>> +
>> + /* Clear the BSS. */
>> + memset(__bss_start, 0, __bss_end - __bss_start);
>> +
>> + /* load/boot image from boot device */
>> + board_init_r(NULL, 0);
>> +}
>> +
>> +void reset_cpu(ulong addr)
>> +{
>> +}
>> +#endif
>>
>
> Best regards,
> Stefano Babic
>
> --
> =====================================================================
> DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
> =====================================================================
Regards,
john
More information about the U-Boot
mailing list