[U-Boot] [PATCH v4 6/7] imx6: SPL support for iMX6 SabreSD
John Tobias
john.tobias.ph at gmail.com
Tue Nov 11 23:50:20 CET 2014
This patch will enable the support for SPL on iMX6 SabreSD.
It tested on SD2 and SD3 mmc port.
It uses mx6dq_dram_iocfg and mx6_dram_cfg for ddr configuration.
Signed-off-by: John Tobias <john.tobias.ph at gmail.com>
---
board/freescale/mx6sabresd/mx6sabresd.c | 187 +++++++++++++++++++++++++++++++-
1 file changed, 185 insertions(+), 2 deletions(-)
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 3d81fff..16cfb44 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -27,6 +27,8 @@
#include <i2c.h>
#include <power/pmic.h>
#include <power/pfuze100_pmic.h>
+#include <asm/arch/mx6-ddr.h>
+
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
@@ -55,8 +57,7 @@ DECLARE_GLOBAL_DATA_PTR;
int dram_init(void)
{
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
-
+ gd->ram_size = imx_ddr_size();
return 0;
}
@@ -607,3 +608,185 @@ int checkboard(void)
puts("Board: MX6-SabreSD\n");
return 0;
}
+
+#ifdef CONFIG_SPL_BUILD
+#include <spl.h>
+#include <libfdt.h>
+
+#define BOOT_CFG 0x020D8004
+struct fsl_esdhc_cfg spl_usdhc_cfg;
+
+const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = {
+ .dram_sdclk_0 = 0x00020030,
+ .dram_sdclk_1 = 0x00020030,
+ .dram_cas = 0x00020030,
+ .dram_ras = 0x00020030,
+ .dram_reset = 0x00020030,
+ .dram_sdcke0 = 0x00003000,
+ .dram_sdcke1 = 0x00003000,
+ .dram_sdba2 = 0x00000000,
+ .dram_sdodt0 = 0x00003030,
+ .dram_sdodt1 = 0x00003030,
+ .dram_sdqs0 = 0x00000030,
+ .dram_sdqs1 = 0x00000030,
+ .dram_sdqs2 = 0x00000030,
+ .dram_sdqs3 = 0x00000030,
+ .dram_sdqs4 = 0x00000030,
+ .dram_sdqs5 = 0x00000030,
+ .dram_sdqs6 = 0x00000030,
+ .dram_sdqs7 = 0x00000030,
+ .dram_dqm0 = 0x00020030,
+ .dram_dqm1 = 0x00020030,
+ .dram_dqm2 = 0x00020030,
+ .dram_dqm3 = 0x00020030,
+ .dram_dqm4 = 0x00020030,
+ .dram_dqm5 = 0x00020030,
+ .dram_dqm6 = 0x00020030,
+ .dram_dqm7 = 0x00020030,
+};
+
+const struct mx6dq_iomux_grp_regs mx6_grp_ioregs = {
+ .grp_ddr_type = 0x000C0000,
+ .grp_ddrmode_ctl = 0x00020000,
+ .grp_ddrpke = 0x00000000,
+ .grp_addds = 0x00000030,
+ .grp_ctlds = 0x00000030,
+ .grp_ddrmode = 0x00020000,
+ .grp_b0ds = 0x00000030,
+ .grp_b1ds = 0x00000030,
+ .grp_b2ds = 0x00000030,
+ .grp_b3ds = 0x00000030,
+ .grp_b4ds = 0x00000030,
+ .grp_b5ds = 0x00000030,
+ .grp_b6ds = 0x00000030,
+ .grp_b7ds = 0x00000030,
+};
+
+const struct mx6_mmdc_calibration mx6_mmcd_calib = {
+ .p0_mpwldectrl0 = 0x001F001F,
+ .p0_mpwldectrl1 = 0x001F001F,
+ .p1_mpwldectrl0 = 0x00440044,
+ .p1_mpwldectrl1 = 0x00440044,
+ .p0_mpdgctrl0 = 0x434B0350,
+ .p0_mpdgctrl1 = 0x034C0359,
+ .p1_mpdgctrl0 = 0x434B0350,
+ .p1_mpdgctrl1 = 0x03650348,
+ .p0_mprddlctl = 0x4436383B,
+ .p1_mprddlctl = 0x39393341,
+ .p0_mpwrdlctl = 0x35373933,
+ .p1_mpwrdlctl = 0x48254A36,
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+ .mem_speed = 1600,
+ .density = 4,
+ .width = 64,
+ .banks = 8,
+ .rowaddr = 14,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1375,
+ .trcmin = 4875,
+ .trasmin = 3500,
+};
+
+/*
+ * This section require the differentiation
+ * between iMX6 Sabre Families.
+ * But for now, it will configure only for
+ * SabreSD.
+ */
+static void spl_dram_init(void)
+{
+ struct mx6_ddr_sysinfo sysinfo = {
+ /* width of data bus:0=16,1=32,2=64 */
+ .dsize = mem_ddr.width/32,
+ /* config for full 4GB range so that get_mem_size() works */
+ .cs_density = 32, /* 32Gb per CS */
+ /* single chip select */
+ .ncs = 2,
+ .cs1_mirror = 0,
+ .rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
+#ifdef RTT_NOM_120OHM
+ .rtt_nom = 2 /*DDR3_RTT_120_OHM*/, /* RTT_Nom = RZQ/2 */
+#else
+ .rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
+#endif
+ .walat = 1, /* Write additional latency */
+ .ralat = 5, /* Read additional latency */
+ .mif3_mode = 3, /* Command prediction working mode */
+ .bi_on = 1, /* Bank interleaving enabled */
+ .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
+ .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
+ };
+
+ mx6dq_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+ mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+int spl_board_mmc_init(bd_t *bis)
+{
+ unsigned reg = readl(BOOT_CFG) >> 11;
+ /*
+ * Upon reading BOOT_CFG register the following map is done:
+ * Bit 11 and 12 of BOOT_CFG register can determine the current
+ * mmc port
+ * 0x1 SD1
+ * 0x2 SD2
+ * 0x3 SD4
+ */
+ switch (reg & 0x3) {
+ case 0x1:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+ spl_usdhc_cfg.esdhc_base = USDHC2_BASE_ADDR;
+ spl_usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+ gd->arch.sdhc_clk = spl_usdhc_cfg.sdhc_clk;
+ break;
+ case 0x2:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+ spl_usdhc_cfg.esdhc_base = USDHC3_BASE_ADDR;
+ spl_usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ gd->arch.sdhc_clk = spl_usdhc_cfg.sdhc_clk;
+ break;
+ case 0x3:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+ spl_usdhc_cfg.esdhc_base = USDHC4_BASE_ADDR;
+ spl_usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+ gd->arch.sdhc_clk = spl_usdhc_cfg.sdhc_clk;
+ break;
+ }
+
+ return fsl_esdhc_initialize(bis, &spl_usdhc_cfg);
+}
+
+void board_init_f(ulong dummy)
+{
+ /* setup AIPS and disable watchdog */
+ arch_cpu_init();
+
+ /* iomux and setup of i2c */
+ board_early_init_f();
+
+ /* setup GP timer */
+ timer_init();
+
+ /* UART clocks enabled and gd valid - init serial console */
+ preloader_console_init();
+
+ /* DDR initialization */
+ spl_dram_init();
+
+ /* Clear the BSS. */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ /* load/boot image from boot device */
+ board_init_r(NULL, 0);
+}
+
+void reset_cpu(ulong addr)
+{
+}
+#endif
--
1.9.1
More information about the U-Boot
mailing list