[U-Boot] [PATCH v3 14/30] ARM: tegra: Enable PCIe on TrimSlice

[Simon Glass]

From: Thierry Reding <treding at nvidia.com>

The TrimSlice has an ethernet NIC connected to the PCIe bus. Enable the
PCIe controller and the network driver so that the device can boot over
the network.

Signed-off-by: Thierry Reding <treding at nvidia.com>
Signed-off-by: Simon Glass <sjg at chromium.org>
---

Changes in v3: None

 arch/arm/dts/tegra20-trimslice.dts   | 69 ++++++++++++++++++++++++++++++++++++
 board/compulab/trimslice/trimslice.c |  8 +++++
 include/configs/trimslice.h          | 10 ++++++
 3 files changed, 87 insertions(+)

diff --git a/arch/arm/dts/tegra20-trimslice.dts b/arch/arm/dts/tegra20-trimslice.dts
index 74e8a16..1637cbd 100644
--- a/arch/arm/dts/tegra20-trimslice.dts
+++ b/arch/arm/dts/tegra20-trimslice.dts
@@ -47,6 +47,20 @@
 		status = "disabled";
 	};
 
+	pcie-controller at 80003000 {
+		status = "okay";
+
+		avdd-pex-supply = <&pci_vdd_reg>;
+		vdd-pex-supply = <&pci_vdd_reg>;
+		avdd-pex-pll-supply = <&pci_vdd_reg>;
+		avdd-plle-supply = <&pci_vdd_reg>;
+		vddio-pex-clk-supply = <&pci_clk_reg>;
+
+		pci at 1,0 {
+			status = "okay";
+		};
+	};
+
 	usb at c5000000 {
 		nvidia,vbus-gpio = <&gpio 170 0>; /* PV2 */
 	};
@@ -66,4 +80,59 @@
 		wp-gpios = <&gpio 122 0>; /* gpio PP2 */
 		bus-width = <4>;
 	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hdmi_vdd_reg: regulator at 0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "avdd_hdmi";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		hdmi_pll_reg: regulator at 1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "avdd_hdmi_pll";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		vbus_reg: regulator at 2 {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "usb1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			gpio = <&gpio TEGRA_GPIO(V, 2) 0>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pci_clk_reg: regulator at 3 {
+			compatible = "regulator-fixed";
+			reg = <3>;
+			regulator-name = "pci_clk";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		pci_vdd_reg: regulator at 4 {
+			compatible = "regulator-fixed";
+			reg = <4>;
+			regulator-name = "pci_vdd";
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-always-on;
+		};
+	};
+
 };
diff --git a/board/compulab/trimslice/trimslice.c b/board/compulab/trimslice/trimslice.c
index 723293f..c9da80d 100644
--- a/board/compulab/trimslice/trimslice.c
+++ b/board/compulab/trimslice/trimslice.c
@@ -13,6 +13,7 @@
 #include <asm/arch/pinmux.h>
 #include <asm/gpio.h>
 #include <i2c.h>
+#include <netdev.h>
 
 void pin_mux_usb(void)
 {
@@ -40,3 +41,10 @@ void pin_mux_mmc(void)
 	/* For CD GPIO PP1 */
 	pinmux_tristate_disable(PMUX_PINGRP_DAP3);
 }
+
+#ifdef CONFIG_PCI
+int board_eth_init(bd_t *bis)
+{
+	return pci_eth_init(bis);
+}
+#endif
diff --git a/include/configs/trimslice.h b/include/configs/trimslice.h
index a254f86..59f4f67 100644
--- a/include/configs/trimslice.h
+++ b/include/configs/trimslice.h
@@ -60,6 +60,16 @@
 #define CONFIG_USB_HOST_ETHER
 #define CONFIG_USB_ETHER_ASIX
 
+/* PCI host support */
+#define CONFIG_PCI
+#define CONFIG_PCI_TEGRA
+#define CONFIG_PCI_PNP
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PCI_ENUM
+
+/* PCI networking support */
+#define CONFIG_RTL8169
+
 /* General networking support */
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_DHCP
-- 
2.1.0.rc2.206.gedb03e5