[U-Boot] [PATCH 3/5] serial: pl01x: move all line control at same place
Vikas Manocha
vikas.manocha at st.com
Tue Nov 18 01:17:51 CET 2014
Receive line control uses same setting as transmit line control, also one lcrh
write is effective for both baud rate & receive line control internal update.
Signed-off-by: Vikas Manocha <vikas.manocha at st.com>
---
drivers/serial/serial_pl01x.c | 40 +++++++++++++++++++---------------------
1 file changed, 19 insertions(+), 21 deletions(-)
diff --git a/drivers/serial/serial_pl01x.c b/drivers/serial/serial_pl01x.c
index c0531ca..3155840 100644
--- a/drivers/serial/serial_pl01x.c
+++ b/drivers/serial/serial_pl01x.c
@@ -72,8 +72,6 @@ static int pl01x_tstc(struct pl01x_regs *regs)
static int pl01x_generic_serial_init(struct pl01x_regs *regs,
enum pl01x_type type)
{
- unsigned int lcr;
-
#ifdef CONFIG_PL011_SERIAL_FLUSH_ON_INIT
if (type == TYPE_PL011) {
/* Empty RX fifo if necessary */
@@ -87,15 +85,26 @@ static int pl01x_generic_serial_init(struct pl01x_regs *regs,
/* First, disable everything */
writel(0, ®s->pl010_cr);
- /* Set the UART to be 8 bits, 1 stop bit, no parity, fifo enabled */
- lcr = UART_PL011_LCRH_WLEN_8 | UART_PL011_LCRH_FEN;
- writel(lcr, ®s->pl011_lcrh);
-
switch (type) {
case TYPE_PL010:
break;
- case TYPE_PL011: {
+ case TYPE_PL011:
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int set_line_control(struct pl01x_regs *regs)
+{
+ unsigned int lcr;
+ /* Internal update of baud rate register require line
+ * control register write */
+ lcr = UART_PL011_LCRH_WLEN_8 | UART_PL011_LCRH_FEN;
#ifdef CONFIG_PL011_SERIAL_RLCR
+ {
int i;
/*
@@ -107,22 +116,15 @@ static int pl01x_generic_serial_init(struct pl01x_regs *regs,
writel(lcr, ®s->fr);
writel(lcr, ®s->pl011_rlcr);
- /* lcrh needs to be set again for change to be effective */
- writel(lcr, ®s->pl011_lcrh);
-#endif
- break;
}
- default:
- return -EINVAL;
- }
-
+#endif
+ writel(lcr, ®s->pl011_lcrh);
return 0;
}
static int pl01x_generic_setbrg(struct pl01x_regs *regs, enum pl01x_type type,
int clock, int baudrate)
{
- unsigned int lcr;
switch (type) {
case TYPE_PL010: {
unsigned int divisor;
@@ -176,11 +178,7 @@ static int pl01x_generic_setbrg(struct pl01x_regs *regs, enum pl01x_type type,
writel(divider, ®s->pl011_ibrd);
writel(fraction, ®s->pl011_fbrd);
- /* Internal update of baud rate register require line
- * control register write */
- lcr = UART_PL011_LCRH_WLEN_8 | UART_PL011_LCRH_FEN;
- writel(lcr, ®s->pl011_lcrh);
-
+ set_line_control(regs);
/* Finally, enable the UART */
writel(UART_PL011_CR_UARTEN | UART_PL011_CR_TXE |
UART_PL011_CR_RXE | UART_PL011_CR_RTS, ®s->pl011_cr);
--
1.7.9.5
More information about the U-Boot
mailing list