[U-Boot] [PATCH v3 3/5] ls102xa: HYP/non-sec: support for ls102xa boards

[Li.Xiubo at freescale.com]

Hi Albert,


> > > > > > +#if defined(CONFIG_ARMV7_NONSEC) || defined(CONFIG_ARMV7_VIRT)
> > > > > > +/* Setting the address at which secondary cores start from.*/
> > > > > > +void smp_set_core_boot_addr(unsigned long addr, int corenr)
> > > > > > +{
> > > > > > +	struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
> > > > > > +
> > > > > > +	/*
> > > > > > +	 * After setting the secondary cores start address,
> > > > > > +	 * just release them to boot.
> > > > > > +	 */
> > > > > > +	out_be32(&gur->scratchrw[0], addr);
> > > > > > +	out_be32(&gur->brrl, 0x2);
> > > > > > +}
> > > > >
> > > > > This function does not exactly "[set] the address at which secondary
> > > > > cores start from"; it sets *a* secondary core's boot address, and then
> > > > > it *boots* it.
> > > > >
> > > >
> > > > Okay, I will fix it later.
> > > >
> > > > > Why does this version of smp_set_core_boot_addr() need to boot the
> core
> > > > > in addition to setting the address, whereas the existing ones in
> > > > > virt_v7, vexpress_common and arndale don't boot the cores?
> > > > >
> > > >
> > > > Yes, they don't doing the release operation.
> > > >
> > > > For Low Power Management requirement, maybe only one core will be used,
> and
> > > then
> > > > We also make sure that the secondary core must be in low power and deep
> > > sleep
> > > > mode(using wfi). So I just release it here, to make sure that the wfi
> > > instruction
> > > > will be executed as early as possible.
> > >
> > > Right after smp_set_core_boot_addr() is called, kick_all_cpus() isgoing
> > > to be called. Wouldn't that boot your CPUs just as well?
> > >
> >
> > Yes, it will.
> >
> > But before that we must do the holdoff bit set operation as the SoC's
> requirement.
> >
> > The BRR contains control bits for enabling boot for each core. On exiting
> HRESET or
> > PORESET, the RCW BOOT_HO field optionally allows for logical core 0 to be
> released
> > for booting or to remain in boot holdoff. All other cores remain in boot
> holdoff until their
> > corresponding bit is set.
> >
> > Maybe the comment is not very clear and a bit confusing.
> 
> Before I'm lost entirely, do you mean that the comment:
> 
> > > > > > +	/*
> > > > > > +	 * After setting the secondary cores start address,
> > > > > > +	 * just release them to boot.
> > > > > > +	 */
> 
> Is actually wrong, and the instructions that follow it do not actually
> boot the secondary core(s)?
> 

The comment should be:
    /*
     * After setting the secondary core's start address,
     * just release it from holdoff.
     */
>From my tests, for most time the release instructions will boot the secondary
core(s) without smp_kick_all_cpus(). One time has failed.

So I think the release can not make sure that it will boot the secondary core(s).

Thanks,

BRs
Xiubo