[U-Boot] [PATCH v8 2/3] Odroid-XU3: Add support for Odroid-XU3
Hyungwon Hwang
human.hwang at samsung.com
Mon Nov 24 04:59:04 CET 2014
Dear Jaehoon Chung,
On Thu, 20 Nov 2014 21:08:30 +0900
Jaehoon Chung <jh80.chung at samsung.com> wrote:
> Hi,
>
> CPU: Exynos5800 at 1200MHz
> Board: Odroid XU3 based on EXYNOS5422
>
> Exynos5800? is it right?
>
Exynos5800 is a variant of Exynos5422 for chromebook, so they are
almost same. The support for this SOC is merged earlier than
Exynos5422. At that time, they used 5800 as its name instead of 5422.
It does not make any difference in behavior, at least until now.
> On 11/14/2014 03:25 PM, Hyungwon Hwang wrote:
> > This patch adds support for Odroid-XU3.
> >
> > Signed-off-by: Hyungwon Hwang <human.hwang at samsung.com>
> > Tested-by: Lukasz Majewski <l.majewski at samsung.com>
> > Acked-by: Lukasz Majewski <l.majewski at samsung.com>
> > Cc: Minkyu Kang <mk7.kang at samsung.com>
> > Cc: Lukasz Majewski <l.majewski at samsung.com>
> > ---
> > Changes for v3:
> > - Remove unnecessary node from DT file
> > - Remove unnecessary features from config file
> > - Remove unnecessary macros from board-specific header file
> > - Fix some trivial typos in comments
> >
> > Changes for v4:
> > - Add MMC FIFO buffer's configuration to DT file
> > - Make CONFIG_OF_CONTROL be set by the target information
> > - Add basic document to doc/README.odroid-xu3
> > - Add CONFIG_CMD_EXT4 to config file
> > - Add environment size and offset to config file
> > - Add extra default environment to make bootable without
> > modification
> > - Remove unnecessary features from config file
> >
> > Changes for v5:
> > - Convert /include/ to #include in DT file
> >
> > Changes for v6:
> > - Separate out the documentation to new commit
> > - Remove unnecessary header file inclusions from the board-specific
> > setup file
> > - Make the function board_clock_init be declared, only when
> > CONFIG_BOARD_EARLY_INIT_F is defined
> >
> > Changes for v7:
> > - Remove OF_CONTROL dependency from !SPL_BUILD
> >
> > Changes for v8:
> > - Remove unnecessary properties in DT mmc node
> >
> > arch/arm/cpu/armv7/exynos/Kconfig | 5 ++
> > arch/arm/dts/Makefile | 3 +-
> > arch/arm/dts/exynos5422-odroidxu3.dts | 57 ++++++++++++++
> > board/samsung/odroid-xu3/Kconfig | 12 +++
> > board/samsung/odroid-xu3/MAINTAINERS | 6 ++
> > board/samsung/odroid-xu3/Makefile | 7 ++
> > board/samsung/odroid-xu3/odroid-xu3.c | 122
> > ++++++++++++++++++++++++++++ board/samsung/odroid-xu3/setup.h
> > | 95 ++++++++++++++++++++++ configs/odroid-xu3_defconfig
> > | 4 + include/configs/odroid_xu3.h | 144
> > ++++++++++++++++++++++++++++++++++ 10 files changed, 454
> > insertions(+), 1 deletion(-) create mode 100644
> > arch/arm/dts/exynos5422-odroidxu3.dts create mode 100644
> > board/samsung/odroid-xu3/Kconfig create mode 100644
> > board/samsung/odroid-xu3/MAINTAINERS create mode 100644
> > board/samsung/odroid-xu3/Makefile create mode 100644
> > board/samsung/odroid-xu3/odroid-xu3.c create mode 100644
> > board/samsung/odroid-xu3/setup.h create mode 100644
> > configs/odroid-xu3_defconfig create mode 100644
> > include/configs/odroid_xu3.h
> >
> > diff --git a/arch/arm/cpu/armv7/exynos/Kconfig
> > b/arch/arm/cpu/armv7/exynos/Kconfig index 13dbd95..16c9a0e 100644
> > --- a/arch/arm/cpu/armv7/exynos/Kconfig
> > +++ b/arch/arm/cpu/armv7/exynos/Kconfig
> > @@ -24,6 +24,10 @@ config TARGET_TRATS2
> > config TARGET_ODROID
> > bool "Exynos4412 Odroid board"
> >
> > +config TARGET_ODROID_XU3
> > + bool "Exynos5422 Odroid board"
> > + select OF_CONTROL
> > +
> > config TARGET_ARNDALE
> > bool "Exynos5250 Arndale board"
> > select SUPPORT_SPL
> > @@ -65,6 +69,7 @@ source "board/samsung/universal_c210/Kconfig"
> > source "board/samsung/origen/Kconfig"
> > source "board/samsung/trats2/Kconfig"
> > source "board/samsung/odroid/Kconfig"
> > +source "board/samsung/odroid-xu3/Kconfig"
> > source "board/samsung/arndale/Kconfig"
> > source "board/samsung/smdk5250/Kconfig"
> > source "board/samsung/smdk5420/Kconfig"
> > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> > index 2b9bd93..d984f34 100644
> > --- a/arch/arm/dts/Makefile
> > +++ b/arch/arm/dts/Makefile
> > @@ -12,7 +12,8 @@ dtb-$(CONFIG_EXYNOS5) += exynos5250-arndale.dtb \
> > exynos5250-smdk5250.dtb \
> > exynos5420-smdk5420.dtb \
> > exynos5420-peach-pit.dtb \
> > - exynos5800-peach-pi.dtb
> > + exynos5800-peach-pi.dtb \
> > + exynos5422-odroidxu3.dtb
> > dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
> > tegra20-medcom-wide.dtb \
> > tegra20-paz00.dtb \
> > diff --git a/arch/arm/dts/exynos5422-odroidxu3.dts
> > b/arch/arm/dts/exynos5422-odroidxu3.dts new file mode 100644
> > index 0000000..533d88e
> > --- /dev/null
> > +++ b/arch/arm/dts/exynos5422-odroidxu3.dts
> > @@ -0,0 +1,57 @@
> > +/*
> > + * Odroid XU3 device tree source
> > + *
> > + * Copyright (c) 2014 Samsung Electronics Co., Ltd.
> > + * http://www.samsung.com
> > + *
> > + * SPDX-License-Identifier: GPL-2.0+
> > + */
> > +
> > +/dts-v1/;
> > +#include "exynos54xx.dtsi"
> > +
> > +/ {
> > + model = "Odroid XU3 based on EXYNOS5422";
> > + compatible = "samsung,odroidxu3", "samsung,exynos5";
> > +
> > + aliases {
> > + serial0 = "/serial at 12C00000";
> > + console = "/serial at 12C20000";
> > + };
> > +
> > + memory {
> > + device_type = "memory";
> > + reg = <0x40000000 0x10000000
> > + 0x50000000 0x10000000
> > + 0x60000000 0x10000000
> > + 0x70000000 0x10000000
> > + 0x80000000 0x10000000
> > + 0x90000000 0x10000000
> > + 0xa0000000 0x10000000
> > + 0xb0000000 0xea00000>;
> > + };
> > +
> > + serial at 12C20000 {
> > + status="okay";
> > + };
> > +
> > + mmc at 12200000 {
> > + samsung,bus-width = <8>;
> > + samsung,timing = <1 3 3>;
> > + fifoth_val = <0x200f0020>;
>
> how did you get fifoth_val and timing?
I got this configuration from u-boot made by Hardkernel.
>
> > + };
> > +
> > + mmc at 12210000 {
> > + status = "disabled";
> > + };
> > +
> > + mmc at 12220000 {
> > + samsung,bus-width = <4>;
> > + samsung,timing = <1 2 3>;
> > + fifoth_val = <0x200f0020>;
> > + };
> > +
> > + mmc at 12230000 {
> > + status = "disabled";
> > + };
> > +};
> > diff --git a/board/samsung/odroid-xu3/Kconfig
> > b/board/samsung/odroid-xu3/Kconfig new file mode 100644
> > index 0000000..6159692
> > --- /dev/null
> > +++ b/board/samsung/odroid-xu3/Kconfig
> > @@ -0,0 +1,12 @@
> > +if TARGET_ODROID_XU3
> > +
> > +config SYS_BOARD
> > + default "odroid-xu3"
> > +
> > +config SYS_VENDOR
> > + default "samsung"
> > +
> > +config SYS_CONFIG_NAME
> > + default "odroid_xu3"
> > +
> > +endif
> > diff --git a/board/samsung/odroid-xu3/MAINTAINERS
> > b/board/samsung/odroid-xu3/MAINTAINERS new file mode 100644
> > index 0000000..50cf928
> > --- /dev/null
> > +++ b/board/samsung/odroid-xu3/MAINTAINERS
> > @@ -0,0 +1,6 @@
> > +ODROID-XU3 BOARD
> > +M: Hyungwon Hwang <human.hwang at samsung.com>
> > +S: Maintained
> > +F: board/samsung/odroid-xu3/
> > +F: include/configs/odroid_xu3.h
> > +F: configs/odroid-xu3_defconfig
> > diff --git a/board/samsung/odroid-xu3/Makefile
> > b/board/samsung/odroid-xu3/Makefile new file mode 100644
> > index 0000000..85ae5c5
> > --- /dev/null
> > +++ b/board/samsung/odroid-xu3/Makefile
> > @@ -0,0 +1,7 @@
> > +#
> > +# Copyright (c) 2014 Samsung Electronics Co., Ltd. All rights
> > reserved. +#
> > +# SPDX-License-Identifier: GPL-2.0+
> > +#
> > +
> > +obj-y := odroid-xu3.o
> > diff --git a/board/samsung/odroid-xu3/odroid-xu3.c
> > b/board/samsung/odroid-xu3/odroid-xu3.c new file mode 100644
> > index 0000000..8c54842
> > --- /dev/null
> > +++ b/board/samsung/odroid-xu3/odroid-xu3.c
> > @@ -0,0 +1,122 @@
> > +/*
> > + * Copyright (C) 2014 Samsung Electronics
> > + * Hyungwon Hwang <human.hwang at samsung.com>
> > + *
> > + * SPDX-License-Identifier: GPL-2.0+
> > + */
> > +
> > +#include <common.h>
> > +#include <asm/arch/clock.h>
> > +#include "setup.h"
> > +
> > +DECLARE_GLOBAL_DATA_PTR;
> > +
> > +unsigned int get_board_rev(void)
> > +{
> > + return 0;
> > +}
> > +
> > +int exynos_init(void)
> > +{
> > + return 0;
> > +}
> > +
> > +#ifdef CONFIG_BOARD_EARLY_INIT_F
> > +static int board_clock_init(void)
> > +{
> > + unsigned int set, clr, clr_src_cpu, clr_pll_con0;
> > + struct exynos5420_clock *clk = (struct exynos5420_clock *)
> > +
> > samsung_get_base_clock();
> > + /*
> > + * CMU_CPU clocks src to MPLL
> > + * Bit values: 0 ; 1
> > + * MUX_APLL_SEL: FIN_PLL ; FOUT_APLL
> > + * MUX_CORE_SEL: MOUT_APLL ; SCLK_MPLL
> > + * MUX_HPM_SEL: MOUT_APLL ; SCLK_MPLL_USER_C
> > + * MUX_MPLL_USER_SEL_C: FIN_PLL ; SCLK_MPLL
> > + */
> > +
> > + /* Set CMU_CPU clocks src to OSCCLK */
> > + clr_src_cpu = MUX_APLL_SEL(1) | MUX_CORE_SEL(1);
> > + set = MUX_APLL_SEL(0) | MUX_CORE_SEL(1);
> > +
> > + clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set);
> > +
> > + while (MUX_STAT_CPU_CHANGING(readl(&clk->mux_stat_cpu)))
> > + continue;
> > +
> > + /* Set APLL to 1200MHz */
> > + clr_pll_con0 = SDIV(7) | PDIV(63) | MDIV(1023) | FSEL(1) |
> > + PLL_ENABLE(1);
> > + set = SDIV(0) | PDIV(2) | MDIV(100) | PLL_ENABLE(1);
> > +
> > + clrsetbits_le32(&clk->apll_con0, clr_pll_con0, set);
> > +
> > + while (!(readl(&clk->apll_con0) & PLL_LOCKED_BIT))
> > + continue;
> > +
> > + /* Set CMU_CPU clocks src to APLL */
> > + set = MUX_APLL_SEL(1) | MUX_CORE_SEL(0);
> > + clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set);
> > +
> > + while (MUX_STAT_CPU_CHANGING(readl(&clk->mux_stat_cpu)))
> > + continue;
> > +
> > + clr = ARM_RATIO(7) | CPUD_RATIO(7) | ATB_RATIO(7) |
> > + PCLK_DBG_RATIO(7) | APLL_RATIO(7) | ARM2_RATIO(7);
> > + set = ARM_RATIO(0) | CPUD_RATIO(2) | ATB_RATIO(5) |
> > + PCLK_DBG_RATIO(5) | APLL_RATIO(0) | ARM2_RATIO(0);
> > +
> > + clrsetbits_le32(&clk->div_cpu0, clr, set);
> > +
> > + while (readl(&clk->div_stat_cpu0) & DIV_STAT_CPU0_CHANGING)
> > + continue;
> > +
> > + /* Set MPLL to 800MHz */
> > + set = SDIV(1) | PDIV(3) | MDIV(200) | PLL_ENABLE(1);
> > +
> > + clrsetbits_le32(&clk->mpll_con0, clr_pll_con0, set);
> > +
> > + while (!(readl(&clk->mpll_con0) & PLL_LOCKED_BIT))
> > + continue;
> > +
> > + /* Set CLKMUX_UART src to MPLL */
> > + clr = UART0_SEL(7) | UART1_SEL(7) | UART2_SEL(7) |
> > UART3_SEL(7);
> > + set = UART0_SEL(3) | UART1_SEL(3) | UART2_SEL(3) |
> > UART3_SEL(3); +
> > + clrsetbits_le32(&clk->src_peric0, clr, set);
> > +
> > + /* Set SCLK_UART to 400 MHz (MPLL / 2) */
> > + clr = UART0_RATIO(15) | UART1_RATIO(15) | UART2_RATIO(15) |
> > + UART3_RATIO(15);
> > + set = UART0_RATIO(1) | UART1_RATIO(1) | UART2_RATIO(1) |
> > + UART3_RATIO(1);
> > +
> > + clrsetbits_le32(&clk->div_peric0, clr, set);
> > +
> > + while (readl(&clk->div_stat_peric0) &
> > DIV_STAT_PERIC0_CHANGING)
> > + continue;
> > +
> > + /* Set CLKMUX_MMC src to MPLL */
> > + clr = MUX_MMC0_SEL(7) | MUX_MMC1_SEL(7) | MUX_MMC2_SEL(7);
> > + set = MUX_MMC0_SEL(3) | MUX_MMC1_SEL(3) | MUX_MMC2_SEL(3);
> > +
> > + clrsetbits_le32(&clk->src_fsys, clr, set);
> > +
> > + clr = MMC0_RATIO(0x3ff) | MMC1_RATIO(0x3ff) |
> > MMC2_RATIO(0x3ff);
> > + set = MMC0_RATIO(0) | MMC1_RATIO(0) | MMC2_RATIO(0);
> > +
> > + clrsetbits_le32(&clk->div_fsys1, clr, set);
> > +
> > + /* Wait for divider ready status */
> > + while (readl(&clk->div_stat_fsys1) &
> > DIV_STAT_FSYS1_CHANGING)
> > + continue;
> > +
> > + return 0;
> > +}
> > +
> > +int exynos_early_init_f(void)
> > +{
> > + return board_clock_init();
> > +}
> > +#endif
> > diff --git a/board/samsung/odroid-xu3/setup.h
> > b/board/samsung/odroid-xu3/setup.h new file mode 100644
> > index 0000000..143c189
> > --- /dev/null
> > +++ b/board/samsung/odroid-xu3/setup.h
> > @@ -0,0 +1,95 @@
> > +/*
> > + * (C) Copyright 2014 Samsung Electronics
> > + * Hyungwon Hwang <human.hwang at samsung.com>
> > + *
> > + * SPDX-License-Identifier: GPL-2.0+
> > + */
> > +
> > +#ifndef __ODROID_XU3_SETUP__
> > +#define __ODROID_XU3_SETUP__
> > +
> > +#define SDIV(x) ((x) & 0x7)
> > +#define PDIV(x) (((x) & 0x3f) << 8)
> > +#define MDIV(x) (((x) & 0x3ff) << 16)
> > +#define FSEL(x) (((x) & 0x1) << 27)
> > +#define PLL_LOCKED_BIT (0x1 << 29)
> > +#define PLL_ENABLE(x) (((x) & 0x1) << 31)
> > +
> > +/* CLK_SRC_CPU */
> > +#define MUX_APLL_SEL(x) ((x) & 0x1)
> > +#define MUX_CORE_SEL(x) (((x) & 0x1) << 16)
> > +
> > +/* CLK_MUX_STAT_CPU */
> > +#define APLL_SEL(x) ((x) & 0x7)
> > +#define CORE_SEL(x) (((x) & 0x7) << 16)
> > +#define MUX_STAT_CPU_CHANGING(x) !(((x) & APLL_SEL(0))
> > || \
> > + (x) & APLL_SEL(1)
> > || \
> > + (x) & CORE_SEL(0)
> > || \
> > + (x) & CORE_SEL(1))
> > +
> > +/* CLK_DIV_CPU0 */
> > +#define ARM_RATIO(x) ((x) & 0x7)
> > +#define CPUD_RATIO(x) (((x) & 0x7) << 4)
> > +#define ATB_RATIO(x) (((x) & 0x7) << 16)
> > +#define PCLK_DBG_RATIO(x) (((x) & 0x7) << 20)
> > +#define APLL_RATIO(x) (((x) & 0x7) << 24)
> > +#define ARM2_RATIO(x) (((x) & 0x7) << 28)
> > +
> > +/* CLK_DIV_STAT_CPU0 */
> > +#define DIV_CPUD(x) (((x) & 0x1) << 4)
> > +#define DIV_ATB(x) (((x) & 0x1) << 16)
> > +#define DIV_PCLK_DBG(x) (((x) & 0x1) << 20)
> > +#define DIV_APLL(x) (((x) & 0x1) << 24)
> > +#define DIV_ARM2(x) (((x) & 0x1) << 28)
> > +
> > +#define DIV_STAT_CHANGING 0x1
> > +#define DIV_STAT_CPU0_CHANGING (DIV_CPUD(DIV_STAT_CHANGING) | \
> > + DIV_ATB(DIV_STAT_CHANGING) | \
> > + DIV_PCLK_DBG(DIV_STAT_CHANGING) |
> > \
> > + DIV_APLL(DIV_STAT_CHANGING) | \
> > + DIV_ARM2(DIV_STAT_CHANGING))
> > +
> > +/* Set CLK_SRC_PERIC0 */
> > +#define UART0_SEL(x) (((x) & 0xf) << 4)
> > +#define UART1_SEL(x) (((x) & 0xf) << 8)
> > +#define UART2_SEL(x) (((x) & 0xf) << 12)
> > +#define UART3_SEL(x) (((x) & 0xf) << 16)
> > +
> > +/* Set CLK_DIV_PERIC0 */
> > +#define UART0_RATIO(x) (((x) & 0xf) << 8)
> > +#define UART1_RATIO(x) (((x) & 0xf) << 12)
> > +#define UART2_RATIO(x) (((x) & 0xf) << 16)
> > +#define UART3_RATIO(x) (((x) & 0xf) << 20)
> > +
> > +/* Set CLK_DIV_STAT_PERIC0 */
> > +#define DIV_UART0(x) ((x) & 0x1)
> > +#define DIV_UART1(x) (((x) & 0x1) << 4)
> > +#define DIV_UART2(x) (((x) & 0x1) << 8)
> > +#define DIV_UART3(x) (((x) & 0x1) << 12)
> > +#define DIV_UART4(x) (((x) & 0x1) << 16)
> > +
> > +#define DIV_STAT_PERIC0_CHANGING (DIV_UART4(DIV_STAT_CHANGING) | \
> > + DIV_UART3(DIV_STAT_CHANGING) | \
> > + DIV_UART2(DIV_STAT_CHANGING) | \
> > + DIV_UART1(DIV_STAT_CHANGING) | \
> > + DIV_UART0(DIV_STAT_CHANGING))
> > +
> > +/* CLK_SRC_FSYS */
> > +#define MUX_MMC0_SEL(x) (((x) & 0x7) << 8)
> > +#define MUX_MMC1_SEL(x) (((x) & 0x7) << 12)
> > +#define MUX_MMC2_SEL(x) (((x) & 0x7) << 16)
> > +
> > +/* CLK_DIV_FSYS1 */
> > +#define MMC0_RATIO(x) ((x) & 0x3ff)
> > +#define MMC1_RATIO(x) (((x) & 0x3ff) << 10)
> > +#define MMC2_RATIO(x) (((x) & 0x3ff) << 20)
> > +
> > +#define DIV_MMC0(x) (((x) & 1) << 20)
> > +#define DIV_MMC1(x) (((x) & 1) << 24)
> > +#define DIV_MMC2(x) (((x) & 1) << 28)
> > +
> > +#define DIV_STAT_FSYS1_CHANGING
> > (DIV_MMC0(DIV_STAT_CHANGING) | \
> > + DIV_MMC1(DIV_STAT_CHANGING) | \
> > + DIV_MMC2(DIV_STAT_CHANGING))
> > +
> > +#endif
> > diff --git a/configs/odroid-xu3_defconfig
> > b/configs/odroid-xu3_defconfig new file mode 100644
> > index 0000000..74aa0cf
> > --- /dev/null
> > +++ b/configs/odroid-xu3_defconfig
> > @@ -0,0 +1,4 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_EXYNOS=y
> > +CONFIG_TARGET_ODROID_XU3=y
> > +CONFIG_DEFAULT_DEVICE_TREE="exynos5422-odroidxu3"
> > diff --git a/include/configs/odroid_xu3.h
> > b/include/configs/odroid_xu3.h new file mode 100644
> > index 0000000..cda4f26
> > --- /dev/null
> > +++ b/include/configs/odroid_xu3.h
> > @@ -0,0 +1,144 @@
> > +/*
> > + * Copyright (C) 2013 Samsung Electronics
> > + * Hyungwon Hwang <human.hwang at samsung.com>
> > + *
> > + * SPDX-License-Identifier: GPL-2.0+
> > + */
> > +
> > +#ifndef __CONFIG_ODROID_XU3_H
> > +#define __CONFIG_ODROID_XU3_H
> > +
> > +#include "exynos5-common.h"
> > +
> > +#define CONFIG_SYS_PROMPT "ODROID-XU3 # "
> > +#define CONFIG_IDENT_STRING " for ODROID-XU3"
> > +
> > +#define CONFIG_BOARD_COMMON
> > +
> > +#define CONFIG_SYS_SDRAM_BASE 0x40000000
> > +#define CONFIG_SYS_TEXT_BASE 0x43E00000
> > +
> > +/* select serial console configuration */
> > +#define CONFIG_SERIAL2 /* use SERIAL 2 */
> > +
> > +#define TZPC_BASE_OFFSET 0x10000
> > +
> > +#define CONFIG_CMD_MMC
> > +#define CONFIG_CMD_EXT2
> > +#define CONFIG_CMD_EXT4
> > +#define CONFIG_CMD_FAT
> > +
> > +/*
> > + * FIXME: The number of bank is actually 8. But there is no way to
> > reserver the
> > + * last 16 Mib in the last bank now. So I just excluded the last
> > bank
> > + * temporally.
> > + */
> > +#define CONFIG_NR_DRAM_BANKS 7
> > +#define SDRAM_BANK_SIZE (256UL << 20UL) /*
> > 256 MB */ +
> > +#define CONFIG_ENV_IS_IN_MMC
> > +
> > +#undef CONFIG_ENV_SIZE
> > +#undef CONFIG_ENV_OFFSET
> > +#define CONFIG_ENV_SIZE 4096
> > +#define CONFIG_ENV_OFFSET (SZ_1K * 1280) /* 1.25
> > MiB offset */ +
> > +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR -
> > 0x1000000) +
> > +#define CONFIG_BOOTCOMMAND "run autoboot"
> > +#define
> > CONFIG_DEFAULT_CONSOLE "console=ttySAC2,115200n8\0" +
> > +/*
> > + * Bootable media layout:
> > + * dev: SD eMMC(part boot)
> > + * BL1 1 0
> > + * BL2 31 30
> > + * UBOOT 63 62
> > + * TZSW 2111 2110
> > + * ENV 2560 2560(part user)
> > + *
> > + * MBR Primary partiions:
> > + * Num Name Size Offset
> > + * 1. BOOT: 100MiB 2MiB
> > + * 2. ROOT: -
> > +*/
>
> This comment doesn't need..just add comment "refer to
> README.odroid-xu3". how about?
I agree with you. I will fix it in next version.
>
> > +#ifdef CONFIG_EXTRA_ENV_SETTINGS
> > +#undef CONFIG_EXTRA_ENV_SETTINGS
>
> Why undef? Discard the previous setting value in exynos5-common?
Yes. With this lines, the previous setting is being discarded. To added
commands such as autoboot, we have to override
CONFIG_EXTRA_ENV_SETTINGS. But without remove it previous defined, the
compiler complains about it. Is there other way for this problem?
>
> > +#endif
> > +#define CONFIG_EXTRA_ENV_SETTINGS \
> > + "loadkernel=fatload mmc ${mmcbootdev}:${mmcbootpart}
> > ${kerneladdr} " \
> > + "${kernelname}\0" \
> > + "loadinitrd=fatload mmc ${mmcbootdev}:${mmcbootpart}
> > ${initrdaddr} " \
> > + "${initrdname}\0" \
> > + "loaddtb=fatload mmc ${mmcbootdev}:${mmcbootpart}
> > ${fdtaddr} " \
> > + "${fdtfile}\0" \
> > + "check_ramdisk=" \
> > + "if run loadinitrd; then " \
> > + "setenv initrd_addr ${initrdaddr};" \
> > + "else " \
> > + "setenv initrd_addr -;" \
> > + "fi;\0" \
> > + "check_dtb=" \
> > + "if run loaddtb; then " \
> > + "setenv fdt_addr ${fdtaddr};" \
> > + "else " \
> > + "setenv fdt_addr;" \
> > + "fi;\0" \
> > + "kernel_args=" \
> > + "setenv bootargs
> > root=/dev/mmcblk${mmcrootdev}p${mmcrootpart}" \
> > + " rootwait ${console} ${opts}\0" \
> > + "boot_fit=" \
> > + "setenv kerneladdr 0x42000000;" \
> > + "setenv kernelname Image.itb;" \
> > + "run loadkernel;" \
> > + "run kernel_args;" \
> > + "bootm ${kerneladdr}#${boardname}\0" \
> > + "boot_uimg=" \
> > + "setenv kerneladdr 0x40007FC0;" \
> > + "setenv kernelname uImage;" \
> > + "run check_dtb;" \
> > + "run check_ramdisk;" \
> > + "run loadkernel;" \
> > + "run kernel_args;" \
> > + "bootm ${kerneladdr} ${initrd_addr}
> > ${fdt_addr};\0" \
> > + "boot_zimg=" \
> > + "setenv kerneladdr 0x40007FC0;" \
> > + "setenv kernelname zImage;" \
> > + "run check_dtb;" \
> > + "run check_ramdisk;" \
> > + "run loadkernel;" \
> > + "run kernel_args;" \
> > + "bootz ${kerneladdr} ${initrd_addr}
> > ${fdt_addr};\0" \
> > + "autoboot=" \
> > + "if test -e mmc 0 Image.itb; then; " \
> > + "run boot_fit;" \
> > + "elif test -e mmc 0 zImage; then; " \
> > + "run boot_zimg;" \
> > + "elif test -e mmc 0 uImage; then; " \
> > + "run boot_uimg;" \
> > + "fi;\0" \
> > + "console=" CONFIG_DEFAULT_CONSOLE \
> > + "mmcbootdev=0\0" \
> > + "mmcbootpart=1\0" \
> > + "mmcrootdev=0\0" \
> > + "mmcrootpart=2\0" \
> > + "bootdelay=0\0" \
>
> Use CONFIG_BOOTDELAY.
I will remove it from here.
>
> > + "dfu_alt_info=Please reset the board\0" \
>
> What means "please reset the board?".
DFU is not supported yet. I will remove it.
>
> > + "consoleon=set console console=ttySAC2,115200n8; save;
> > reset\0" \
> > + "consoleoff=set console console=ram; save; reset\0" \
>
> Remove consoleon/off. i know there is CONFIG_SILENT_CONSOLE, is it
> difference?
I agree with you. I will remove it.
>
> Best Regards,
> Jaehoon Chung
>
> > + "initrdname=uInitrd\0" \
> > + "initrdaddr=42000000\0" \
> > + "fdtaddr=40800000\0"
> > +
> > +/* FIXME: MUST BE REMOVED AFTER TMU IS TURNED ON */
> > +#undef CONFIG_EXYNOS_TMU
> > +#undef CONFIG_TMU_CMD_DTT
> > +
> > +#ifdef CONFIG_CMD_NET
> > +#undef CONFIG_CMD_NET
> > +#undef CONFIG_SMC911X
> > +#undef CONFIG_CMD_PXE
> > +#undef CONFIG_MENU
> > +#endif
> > +
> > +#endif /* __CONFIG_H */
> >
>
More information about the U-Boot
mailing list