[U-Boot] AM335x Ethernet pin mux confusion

[Mugunthan V N]

On Monday 24 November 2014 07:57 PM, Andy Pont wrote:
> Hello,
> 
> I am working on porting U-Boot 2014.07 to a custom TI AM3354 based hardware
> platform and am confused trying to set the pin mux for the two Ethernet
> interfaces that are on the board.  
> 
> RGMII1_ pins are connected to an ATHEROS AR8031 PHY (PHY ADDR 04) and the
> pins GPMC_A0 .. GPMC_A11 are connected to a Micrel KSZ8041NL (PHY ADDR 01).
> The output of the "mii info" command looks OK so the MDIO interface looks to
> be OK as it gives:
> 
> PHY 0x00: OUI = 0x0885, Model = 0x11, Rev = 0x03,  10baseT, HDX
> PHY 0x01: OUI = 0x0885, Model = 0x11, Rev = 0x03,  10baseT, HDX
> PHY 0x04: OUI = 0x1374, Model = 0x07, Rev = 0x04, 1000baseX, FDX
> 
> However, with debug enabled, it is reporting the PHYs incorrectly as it
> gives:
> 
> cpsw connected to Micrel KSZ804
> cpsw connected to Micrel KSZ804
> cpsw
> 
> The AR8031 provides a connection to the outside world and the KSZ8041
> connects to an Ethernet switch which then connects on to other devices on
> the board to form a private network.  The DHCP command just sits in a loop
> waiting for PHY auto negotiation to complete but timing out!
> 
> In the SPL code I am setting up the pin mux as follows:
> 
> static struct module_pin_mux rgmii1_pin_mux[] = {
> 	{OFFSET(mii1_txen), MODE(2)},			/* RGMII1_TCTL */
> 	{OFFSET(mii1_rxdv), MODE(2) | RXACTIVE},	/* RGMII1_RCTL */
> 	{OFFSET(mii1_txd3), MODE(2)},			/* RGMII1_TD3 */
> 	{OFFSET(mii1_txd2), MODE(2)},			/* RGMII1_TD2 */
> 	{OFFSET(mii1_txd1), MODE(2)},			/* RGMII1_TD1 */
> 	{OFFSET(mii1_txd0), MODE(2)},			/* RGMII1_TD0 */
> 	{OFFSET(mii1_txclk), MODE(2)},			/* RGMII1_TCLK */
> 	{OFFSET(mii1_rxclk), MODE(2) | RXACTIVE},	/* RGMII1_RCLK */
> 	{OFFSET(mii1_rxd3), MODE(2) | RXACTIVE},	/* RGMII1_RD3 */
> 	{OFFSET(mii1_rxd2), MODE(2) | RXACTIVE},	/* RGMII1_RD2 */
> 	{OFFSET(mii1_rxd1), MODE(2) | RXACTIVE},	/* RGMII1_RD1 */
> 	{OFFSET(mii1_rxd0), MODE(2) | RXACTIVE},	/* RGMII1_RD0 */
> 	{OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},  /* MDIO_DATA
> */
> 	{OFFSET(mdio_clk), MODE(0) | PULLUP_EN},	/* MDIO_CLK */
> 	{-1},
> };
> 
> static struct module_pin_mux rmii2_pin_mux[] = {
> 	{OFFSET(gpmc_a0), MODE(2)},			/* RMII2_TXEN */
> 	{OFFSET(gpmc_a1), MODE(2) | RXACTIVE},		/* RMII2_RXDV */
> 	{OFFSET(gpmc_a2), MODE(2)},			/* RMII2_TXD3 */
> 	{OFFSET(gpmc_a3), MODE(2)},			/* RMII2_TXD2 */
> 	{OFFSET(gpmc_a4), MODE(2)},			/* RMII2_TXD1 */
> 	{OFFSET(gpmc_a5), MODE(2)},			/* RMII2_TXD0 */
> 	{OFFSET(gpmc_a6), MODE(2)},			/* RMII2_TXCLK */
> 	{OFFSET(gpmc_a7), MODE(2) | RXACTIVE},		/* RMII2_RXCLK */
> 	{OFFSET(gpmc_a8), MODE(2) | RXACTIVE},		/* RMII2_RXD3 */
> 	{OFFSET(gpmc_a9), MODE(2) | RXACTIVE},		/* RMII2_RXD2 */
> 	{OFFSET(gpmc_a10), MODE(2) | RXACTIVE},		/* RMII2_RXD1 */
> 	{OFFSET(gpmc_a11), MODE(2) | RXACTIVE},		/* RMII2_RXD0 */
> 	{OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN}, /* MDIO_DATA */
> 	{OFFSET(mdio_clk), MODE(0) | PULLUP_EN},	/* MDIO_CLK */
> 	{-1},
> };
> 
> Any help would be much appreciated?

There is no relation between pinmux and phy attached to the slave.
Is your cpsw slave structures are populated with proper phy ids?

Regards
Mugunthan V N