[U-Boot] [PATCH v4 6/9] dm: imx: Use gpio_request() to request GPIOs
Simon Glass
sjg at chromium.org
Thu Oct 2 03:57:25 CEST 2014
GPIOs should be requested before use. Without this, driver model will not
permit the GPIO to be used.
Signed-off-by: Simon Glass <sjg at chromium.org>
---
Changes in v4:
- Adjust error checking to permit calling gpio_request() multiple times
- Avoid doing low-level SATA init multiple times
- Move SATA changes into this patch
Changes in v3:
- Add a check for the Ethernet gpio_request() also
- Add a comment for the CONFIG_SPL_BUILD #ifdef
- Just warn when one of the board init stages fails
Changes in v2:
- Check return values of gpio_request()
arch/arm/imx-common/i2c-mxv7.c | 24 +++++++++++++++++
board/compulab/cm_fx6/cm_fx6.c | 61 ++++++++++++++++++++++++++++++++----------
board/compulab/cm_fx6/common.c | 14 +++++++++-
3 files changed, 84 insertions(+), 15 deletions(-)
diff --git a/arch/arm/imx-common/i2c-mxv7.c b/arch/arm/imx-common/i2c-mxv7.c
index 70cff5c..aaf6936 100644
--- a/arch/arm/imx-common/i2c-mxv7.c
+++ b/arch/arm/imx-common/i2c-mxv7.c
@@ -4,6 +4,7 @@
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
+#include <malloc.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/errno.h>
@@ -72,10 +73,26 @@ static void * const i2c_bases[] = {
int setup_i2c(unsigned i2c_index, int speed, int slave_addr,
struct i2c_pads_info *p)
{
+ char *name1, *name2;
int ret;
if (i2c_index >= ARRAY_SIZE(i2c_bases))
return -EINVAL;
+
+ name1 = malloc(9);
+ name2 = malloc(9);
+ if (!name1 || !name2)
+ return -ENOMEM;
+ sprintf(name1, "i2c_sda%d", i2c_index);
+ sprintf(name2, "i2c_scl%d", i2c_index);
+ ret = gpio_request(p->sda.gp, name1);
+ if (ret)
+ goto err_req1;
+
+ ret = gpio_request(p->scl.gp, name2);
+ if (ret)
+ goto err_req2;
+
/* Enable i2c clock */
ret = enable_i2c_clk(1, i2c_index);
if (ret)
@@ -93,5 +110,12 @@ int setup_i2c(unsigned i2c_index, int speed, int slave_addr,
err_idle:
err_clk:
+ gpio_free(p->scl.gp);
+err_req2:
+ gpio_free(p->sda.gp);
+err_req1:
+ free(name1);
+ free(name2);
+
return ret;
}
diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c
index 9c6e686..53681d4 100644
--- a/board/compulab/cm_fx6/cm_fx6.c
+++ b/board/compulab/cm_fx6/cm_fx6.c
@@ -69,24 +69,52 @@ static iomux_v3_cfg_t const sata_pads[] = {
IOMUX_PADS(PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
-static void cm_fx6_setup_issd(void)
+static int cm_fx6_setup_issd(void)
{
- SETUP_IOMUX_PADS(sata_pads);
- /* Make sure this gpio has logical 0 value */
+ static bool init_done = false;
+ int ret;
+ int i;
+
+ if (!init_done) {
+ SETUP_IOMUX_PADS(sata_pads);
+
+ for (i = 0; i < ARRAY_SIZE(cm_fx6_issd_gpios); i++) {
+ ret = gpio_request(cm_fx6_issd_gpios[i], "sata");
+ if (ret)
+ return ret;
+ }
+
+ /* Make sure this gpio has logical 0 value */
+ ret = gpio_request(CM_FX6_SATA_PWLOSS_INT, "sata_pwloss_int");
+ if (ret)
+ return ret;
+ init_done = true;
+ }
+
gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0);
udelay(100);
cm_fx6_sata_power(0);
mdelay(250);
cm_fx6_sata_power(1);
+
+ return 0;
}
#define CM_FX6_SATA_INIT_RETRIES 10
int sata_initialize(void)
{
- int err, i;
+ int err, i, ret;
- cm_fx6_setup_issd();
+ /*
+ * cm-fx6 may have iSSD not assembled and in this case it has
+ * bypasses for a (m)SATA socket on the baseboard. The socketed
+ * device is not controlled by those GPIOs. So just print a warning
+ * if the setup fails.
+ */
+ ret = cm_fx6_setup_issd();
+ if (ret)
+ printf("Warning: iSSD setup failed!\n");
for (i = 0; i < CM_FX6_SATA_INIT_RETRIES; i++) {
err = setup_sata();
if (err) {
@@ -183,9 +211,9 @@ static int cm_fx6_usb_hub_reset(void)
int err;
err = gpio_request(CM_FX6_USB_HUB_RST, "usb hub rst");
- if (err) {
+ if (err && err != -EBUSY) {
printf("USB hub rst gpio request failed: %d\n", err);
- return -1;
+ return err;
}
SETUP_IOMUX_PAD(PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL));
@@ -199,13 +227,13 @@ static int cm_fx6_usb_hub_reset(void)
static int cm_fx6_init_usb_otg(void)
{
- int ret;
+ int err;
struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
- ret = gpio_request(SB_FX6_USB_OTG_PWR, "usb-pwr");
- if (ret) {
- printf("USB OTG pwr gpio request failed: %d\n", ret);
- return ret;
+ err = gpio_request(SB_FX6_USB_OTG_PWR, "usb-pwr");
+ if (err && err != -EBUSY) {
+ printf("err OTG pwr gpio request failed: %d\n", err);
+ return err;
}
SETUP_IOMUX_PAD(PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL));
@@ -340,12 +368,17 @@ static int handle_mac_address(void)
int board_eth_init(bd_t *bis)
{
- int res = handle_mac_address();
- if (res)
+ int err;
+
+ err = handle_mac_address();
+ if (err)
puts("No MAC address found\n");
SETUP_IOMUX_PADS(enet_pads);
/* phy reset */
+ err = gpio_request(CM_FX6_ENET_NRST, "enet_nrst");
+ if (err)
+ printf("Etnernet NRST gpio request failed: %d\n", err);
gpio_direction_output(CM_FX6_ENET_NRST, 0);
udelay(500);
gpio_set_value(CM_FX6_ENET_NRST, 1);
diff --git a/board/compulab/cm_fx6/common.c b/board/compulab/cm_fx6/common.c
index 1f39679..22ace2f 100644
--- a/board/compulab/cm_fx6/common.c
+++ b/board/compulab/cm_fx6/common.c
@@ -79,6 +79,18 @@ void cm_fx6_set_ecspi_iomux(void)
int board_spi_cs_gpio(unsigned bus, unsigned cs)
{
- return (bus == 0 && cs == 0) ? (CM_FX6_ECSPI_BUS0_CS0) : -1;
+ if (bus != 0 || cs != 0)
+ return -EINVAL;
+
+ /* DM does not support SPL yet and this function is not implemented */
+#ifndef CONFIG_SPL_BUILD
+ int ret;
+
+ ret = gpio_request(CM_FX6_ECSPI_BUS0_CS0, "ecspi_bus0_cs0");
+ if (ret && ret != -EBUSY)
+ return ret;
+#endif
+
+ return CM_FX6_ECSPI_BUS0_CS0;
}
#endif
--
2.1.0.rc2.206.gedb03e5
More information about the U-Boot
mailing list