[U-Boot] [PATCH 7/7] dm: at91: Convert snapper9260 to use driver model

[Simon Glass]

Convert this at91sam9260-based board to use driver model. This should serve
as an example for other similar boards. Serial and GPIO are supported so
far.

Signed-off-by: Simon Glass <sjg at chromium.org>
---

 board/bluewater/snapper9260/snapper9260.c | 18 ++++++++++++++++--
 include/configs/snapper9260.h             |  9 ++++++++-
 2 files changed, 24 insertions(+), 3 deletions(-)

diff --git a/board/bluewater/snapper9260/snapper9260.c b/board/bluewater/snapper9260/snapper9260.c
index bfde129..b98359f 100644
--- a/board/bluewater/snapper9260/snapper9260.c
+++ b/board/bluewater/snapper9260/snapper9260.c
@@ -9,12 +9,15 @@
  */
 
 #include <common.h>
+#include <dm.h>
 #include <asm/io.h>
+#include <asm/gpio.h>
 #include <asm/arch/at91sam9260_matrix.h>
 #include <asm/arch/at91sam9_smc.h>
 #include <asm/arch/at91_common.h>
 #include <asm/arch/at91_pmc.h>
 #include <asm/arch/gpio.h>
+#include <asm/arch/at91_serial.h>
 #include <net.h>
 #include <netdev.h>
 #include <i2c.h>
@@ -95,10 +98,12 @@ static void nand_hw_init(void)
 	       &smc->cs[3].mode);
 
 	/* Configure RDY/BSY */
-	at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+	gpio_request(CONFIG_SYS_NAND_READY_PIN, "nand_rdy");
+	gpio_direction_input(CONFIG_SYS_NAND_READY_PIN);
 
 	/* Enable NandFlash */
-	at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+	gpio_request(CONFIG_SYS_NAND_ENABLE_PIN, "nand_ce");
+	gpio_direction_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
 }
 
 int board_init(void)
@@ -140,3 +145,12 @@ int dram_init(void)
 void reset_phy(void)
 {
 }
+
+static struct at91_serial_platdata at91sam9260_serial_plat = {
+	.base_addr = ATMEL_BASE_DBGU,
+};
+
+U_BOOT_DEVICE(at91sam9260_serial) = {
+	.name	= "serial_at91",
+	.platdata = &at91sam9260_serial_plat,
+};
diff --git a/include/configs/snapper9260.h b/include/configs/snapper9260.h
index fdb6cca..251ef07 100644
--- a/include/configs/snapper9260.h
+++ b/include/configs/snapper9260.h
@@ -21,6 +21,11 @@
 #define CONFIG_SYS_AT91_MAIN_CLOCK	18432000 /* External Crystal, in Hz */
 #define CONFIG_SYS_AT91_SLOW_CLOCK	32768
 #define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DM
+#define CONFIG_CMD_DM
+#define CONFIG_DM_GPIO
+#define CONFIG_DM_SERIAL
+#define CONFIG_SYS_MALLOC_F_LEN		(1 << 10)
 
 /* CPU */
 #define CONFIG_ARCH_CPU_INIT
@@ -85,8 +90,10 @@
 
 /* UARTs/Serial console */
 #define CONFIG_ATMEL_USART
+#ifndef CONFIG_DM_SERIAL
 #define CONFIG_USART_BASE		ATMEL_BASE_DBGU
 #define CONFIG_USART_ID			ATMEL_ID_SYS
+#endif
 #define CONFIG_BAUDRATE			115200
 #define CONFIG_SYS_PROMPT		"Snapper> "
 
@@ -160,7 +167,7 @@
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_FAT
 #define CONFIG_CMD_I2C
-#undef CONFIG_CMD_GPIO
+#define CONFIG_CMD_GPIO
 #define CONFIG_CMD_USB
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NAND
-- 
2.1.0.rc2.206.gedb03e5