[U-Boot] [PATCH v2 2/2] imx:mx6sxsabresd add qspi support

[Peng Fan]

Hi,

Any reply about this patch? It is long time since this patch was sent out.

Regards,
Peng.
On 09/11/2014 10:30 AM, Fan Peng-B51431 wrote:
> Just CC Stefano Babic <sbabic at denx.de>
> 
> Regards,
> Peng.
> 
> -----Original Message-----
> From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Peng Fan
> Sent: Thursday, September 11, 2014 9:56 AM
> To: Estevam Fabio-R49496; Li Ye-B37916
> Cc: u-boot at lists.denx.de
> Subject: [U-Boot] [PATCH v2 2/2] imx:mx6sxsabresd add qspi support
> 
> Configure the pad setting and enable qspi clock to support qspi flashes access.
> 
> This patch has been tested on mx6sxsabresd board.
> 
> Signed-off-by: Peng Fan <Peng.Fan at freescale.com>
> ---
> 
> Changelog v2:
>  Take Fabio's suggestion, split soc code and board code into two patches.
>  This patch needs 'ARM:MX6SX Add QSPI support' patch.
> 
>  board/freescale/mx6sxsabresd/mx6sxsabresd.c | 40 +++++++++++++++++++++++++++++
>  include/configs/mx6sxsabresd.h              | 14 ++++++++++
>  2 files changed, 54 insertions(+)
> 
> diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
> index 5eaec1b..f9cad5a 100644
> --- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c
> +++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
> @@ -272,11 +272,51 @@ int board_mmc_init(bd_t *bis)
>  	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);  }
>  
> +#ifdef CONFIG_FSL_QSPI
> +
> +#define QSPI_PAD_CTRL1	\
> +	(PAD_CTL_SRE_FAST | PAD_CTL_SPEED_HIGH | \
> +	 PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_40ohm)
> +
> +static iomux_v3_cfg_t const quadspi_pads[] = {
> +	MX6_PAD_NAND_WP_B__QSPI2_A_DATA_0	| MUX_PAD_CTRL(QSPI_PAD_CTRL1),
> +	MX6_PAD_NAND_READY_B__QSPI2_A_DATA_1	| MUX_PAD_CTRL(QSPI_PAD_CTRL1),
> +	MX6_PAD_NAND_CE0_B__QSPI2_A_DATA_2	| MUX_PAD_CTRL(QSPI_PAD_CTRL1),
> +	MX6_PAD_NAND_CE1_B__QSPI2_A_DATA_3	| MUX_PAD_CTRL(QSPI_PAD_CTRL1),
> +	MX6_PAD_NAND_ALE__QSPI2_A_SS0_B		| MUX_PAD_CTRL(QSPI_PAD_CTRL1),
> +	MX6_PAD_NAND_CLE__QSPI2_A_SCLK		| MUX_PAD_CTRL(QSPI_PAD_CTRL1),
> +	MX6_PAD_NAND_DATA07__QSPI2_A_DQS	| MUX_PAD_CTRL(QSPI_PAD_CTRL1),
> +	MX6_PAD_NAND_DATA01__QSPI2_B_DATA_0	| MUX_PAD_CTRL(QSPI_PAD_CTRL1),
> +	MX6_PAD_NAND_DATA00__QSPI2_B_DATA_1	| MUX_PAD_CTRL(QSPI_PAD_CTRL1),
> +	MX6_PAD_NAND_WE_B__QSPI2_B_DATA_2	| MUX_PAD_CTRL(QSPI_PAD_CTRL1),
> +	MX6_PAD_NAND_RE_B__QSPI2_B_DATA_3	| MUX_PAD_CTRL(QSPI_PAD_CTRL1),
> +	MX6_PAD_NAND_DATA03__QSPI2_B_SS0_B	| MUX_PAD_CTRL(QSPI_PAD_CTRL1),
> +	MX6_PAD_NAND_DATA02__QSPI2_B_SCLK	| MUX_PAD_CTRL(QSPI_PAD_CTRL1),
> +	MX6_PAD_NAND_DATA05__QSPI2_B_DQS	| MUX_PAD_CTRL(QSPI_PAD_CTRL1),
> +};
> +
> +int board_qspi_init(void)
> +{
> +	/* Set the iomux */
> +	imx_iomux_v3_setup_multiple_pads(quadspi_pads,
> +					 ARRAY_SIZE(quadspi_pads));
> +
> +	/* Set the clock */
> +	enable_qspi_clk(1);
> +
> +	return 0;
> +}
> +#endif
> +
>  int board_init(void)
>  {
>  	/* Address of boot parameters */
>  	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
>  
> +#ifdef CONFIG_FSL_QSPI
> +	board_qspi_init();
> +#endif
> +
>  	return 0;
>  }
>  
> diff --git a/include/configs/mx6sxsabresd.h b/include/configs/mx6sxsabresd.h index 1eda65e..00031ec 100644
> --- a/include/configs/mx6sxsabresd.h
> +++ b/include/configs/mx6sxsabresd.h
> @@ -201,6 +201,20 @@
>  /* FLASH and environment organization */  #define CONFIG_SYS_NO_FLASH
>  
> +#define CONFIG_FSL_QSPI
> +
> +#ifdef CONFIG_FSL_QSPI
> +#define CONFIG_CMD_SF
> +#define CONFIG_SPI_FLASH
> +#define CONFIG_SPI_FLASH_SPANSION
> +#define CONFIG_SPI_FLASH_STMICRO
> +#define CONFIG_SYS_FSL_QSPI_LE
> +#define CONFIG_QSPI_BASE		QSPI2_BASE_ADDR
> +#define CONFIG_QSPI_MEMMAP_BASE		QSPI2_ARB_BASE_ADDR
> +#define FSL_QSPI_FLASH_SIZE		SZ_16M
> +#define FSL_QSPI_FLASH_NUM		2
> +#endif
> +
>  #define CONFIG_ENV_OFFSET		(6 * SZ_64K)
>  #define CONFIG_ENV_SIZE			SZ_8K
>  #define CONFIG_ENV_IS_IN_MMC
> --
> 1.8.4
> 
> 
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>