[U-Boot] [PATCH V2] sf: Add support for flag status register on Micron chips
Hou Zhiqiang
B48286 at freescale.com
Sat Oct 11 08:40:29 CEST 2014
Enter 3 Byte address mode at first, because it may change to 4 Byte
address mode in kernel driver and not reset to 3 Byte address mode
after reboot.
Add clear flag status register operation that some Micron SPI flash
chips required after reading the flag status register to check some
operations completion.
Signed-off-by: Hou Zhiqiang <B48286 at freescale.com>
Signed-off-by: Mingkai.Hu <Mingkai.Hu at freescale.com>
---
V1:
Based on git://git.denx.de/u-boot.git.
Also can be applied to git://www.denx.de/git/u-boot-mpc85xx.git.
Tested on board T2080QDS and T2080RDB.
V2:
Add the operation of enter 3 Byte address mode in probe.
drivers/mtd/spi/sf_internal.h | 17 ++++++++++++
drivers/mtd/spi/sf_ops.c | 64 +++++++++++++++++++++++++++++++++++++------
drivers/mtd/spi/sf_probe.c | 5 ++++
3 files changed, 78 insertions(+), 8 deletions(-)
diff --git a/drivers/mtd/spi/sf_internal.h b/drivers/mtd/spi/sf_internal.h
index 19d4914..49e5a2c 100644
--- a/drivers/mtd/spi/sf_internal.h
+++ b/drivers/mtd/spi/sf_internal.h
@@ -36,6 +36,11 @@
#define CMD_WRITE_ENABLE 0x06
#define CMD_READ_CONFIG 0x35
#define CMD_FLAG_STATUS 0x70
+#define CMD_CLEAR_FLAG_STATUS 0x50
+
+/* Used for Macronix and Winbond flashes */
+#define CMD_ENTER_4B_ADDR 0xB7
+#define CMD_EXIT_4B_ADDR 0xE9
/* Read commands */
#define CMD_READ_ARRAY_SLOW 0x03
@@ -59,6 +64,8 @@
#define STATUS_QEB_WINSPAN (1 << 1)
#define STATUS_QEB_MXIC (1 << 6)
#define STATUS_PEC (1 << 7)
+#define STATUS_PROT (1 << 1)
+#define STATUS_ERASE (1 << 5)
#ifdef CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
#define STATUS_SRWD (1 << 7) /* SR write protect */
@@ -124,6 +131,12 @@ static inline int spi_flash_cmd_write_disable(struct spi_flash *flash)
return spi_flash_cmd(flash->spi, CMD_WRITE_DISABLE, NULL, 0);
}
+/* Clear flag status register */
+static inline int spi_flash_cmd_clear_flag_status(struct spi_flash *flash)
+{
+ return spi_flash_cmd(flash->spi, CMD_CLEAR_FLAG_STATUS, NULL, 0);
+}
+
/*
* Send the read status command to the device and wait for the wip
* (write-in-progress) bit to clear itself.
@@ -160,4 +173,8 @@ int spi_flash_read_common(struct spi_flash *flash, const u8 *cmd,
int spi_flash_cmd_read_ops(struct spi_flash *flash, u32 offset,
size_t len, void *data);
+#if defined(CONFIG_SPI_FLASH_STMICRO)
+int spi_flash_cmd_4B_addr_switch(struct spi_flash *flash, int enable);
+#endif
+
#endif /* _SF_INTERNAL_H_ */
diff --git a/drivers/mtd/spi/sf_ops.c b/drivers/mtd/spi/sf_ops.c
index 85cf22d..8a532b8 100644
--- a/drivers/mtd/spi/sf_ops.c
+++ b/drivers/mtd/spi/sf_ops.c
@@ -93,6 +93,30 @@ int spi_flash_cmd_write_config(struct spi_flash *flash, u8 wc)
}
#endif
+#if defined(CONFIG_SPI_FLASH_STMICRO)
+int spi_flash_cmd_4B_addr_switch(struct spi_flash *flash, int enable)
+{
+ int ret;
+ u8 cmd;
+
+ cmd = enable ? CMD_ENTER_4B_ADDR : CMD_EXIT_4B_ADDR;
+
+ ret = spi_claim_bus(flash->spi);
+ if (ret) {
+ debug("SF: unable to claim SPI bus\n");
+ return ret;
+ }
+
+ ret = spi_flash_cmd_write_enable(flash);
+ if (ret < 0) {
+ debug("SF: enabling write failed\n");
+ return ret;
+ }
+
+ return spi_flash_cmd(flash->spi, cmd, NULL, 0);
+}
+#endif
+
#ifdef CONFIG_SPI_FLASH_BAR
static int spi_flash_cmd_bankaddr_write(struct spi_flash *flash, u8 bank_sel)
{
@@ -160,6 +184,7 @@ int spi_flash_cmd_wait_ready(struct spi_flash *flash, unsigned long timeout)
unsigned long timebase;
unsigned long flags = SPI_XFER_BEGIN;
int ret;
+ int out_of_time = 1;
u8 status;
u8 check_status = 0x0;
u8 poll_bit = STATUS_WIP;
@@ -186,22 +211,45 @@ int spi_flash_cmd_wait_ready(struct spi_flash *flash, unsigned long timeout)
WATCHDOG_RESET();
ret = spi_xfer(spi, 8, NULL, &status, 0);
- if (ret)
+ if (ret) {
+ spi_xfer(spi, 0, NULL, NULL, SPI_XFER_END);
return -1;
+ }
- if ((status & poll_bit) == check_status)
+ if ((status & poll_bit) == check_status) {
+ out_of_time = 0;
break;
+ }
} while (get_timer(timebase) < timeout);
spi_xfer(spi, 0, NULL, NULL, SPI_XFER_END);
- if ((status & poll_bit) == check_status)
- return 0;
+ if (out_of_time) {
+ /* Timed out */
+ debug("SF: time out!\n");
+ if (cmd == CMD_FLAG_STATUS) {
+ if (spi_flash_cmd_clear_flag_status(flash) < 0)
+ debug("SF: clear flag status failed\n");
+ }
+ ret = -1;
+ }
+#ifdef CONFIG_SPI_FLASH_STMICRO
+ else if (cmd == CMD_FLAG_STATUS) {
+ if (!(status & (STATUS_PROT | STATUS_ERASE))) {
+ ret = 0;
+ } else {
+ debug("SF: flag status error");
+ ret = -1;
+ }
- /* Timed out */
- debug("SF: time out!\n");
- return -1;
+ if (spi_flash_cmd_clear_flag_status(flash) < 0) {
+ debug("SF: clear flag status failed\n");
+ ret = -1;
+ }
+ }
+#endif
+ return ret;
}
int spi_flash_write_common(struct spi_flash *flash, const u8 *cmd,
@@ -234,7 +282,7 @@ int spi_flash_write_common(struct spi_flash *flash, const u8 *cmd,
ret = spi_flash_cmd_wait_ready(flash, timeout);
if (ret < 0) {
- debug("SF: write %s timed out\n",
+ debug("SF: write %s failed\n",
timeout == SPI_FLASH_PROG_TIMEOUT ?
"program" : "page erase");
return ret;
diff --git a/drivers/mtd/spi/sf_probe.c b/drivers/mtd/spi/sf_probe.c
index 4d148d1..79b876d 100644
--- a/drivers/mtd/spi/sf_probe.c
+++ b/drivers/mtd/spi/sf_probe.c
@@ -221,6 +221,11 @@ static struct spi_flash *spi_flash_validate_params(struct spi_slave *spi,
#ifdef CONFIG_SPI_FLASH_STMICRO
if (params->flags & E_FSR)
flash->poll_cmd = CMD_FLAG_STATUS;
+
+ if (flash->size > SPI_FLASH_16MB_BOUN) {
+ if (spi_flash_cmd_4B_addr_switch(flash, 0) < 0)
+ debug("SF: enter 3B address mode failed\n");
+ }
#endif
/* Configure the BAR - discover bank cmds and read current bank */
--
2.1.0.27.g96db324
More information about the U-Boot
mailing list