[U-Boot] [PATCH 2/2] imx: mx6sxsabresd: Add board support for USDHC2 and USDHC3

[Ye.Li]

Add full support for USDHC2, USDHC3, USDHC4 on mx6sx sabresd board.
The default boot socket is USDHC4, so the MMC environment is set to
this device.

Signed-off-by: Ye.Li <B37916 at freescale.com>
---
 board/freescale/mx6sxsabresd/mx6sxsabresd.c |   96 +++++++++++++++++++++++++--
 include/configs/mx6sxsabresd.h              |    6 ++-
 2 files changed, 96 insertions(+), 6 deletions(-)

diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
index 68d3718..6ba646a 100644
--- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c
+++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
@@ -68,6 +68,34 @@ static iomux_v3_cfg_t const uart1_pads[] = {
 	MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
 };
 
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+	MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DATA0__USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DATA1__USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DATA2__USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DATA3__USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DATA4__USDHC3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DATA5__USDHC3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DATA6__USDHC3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DATA7__USDHC3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	/* CD pin */
+	MX6_PAD_KEY_COL0__GPIO2_IO_10 | MUX_PAD_CTRL(NO_PAD_CTRL),
+
+	/* RST_B, used for power reset cycle */
+	MX6_PAD_KEY_COL1__GPIO2_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
 static iomux_v3_cfg_t const usdhc4_pads[] = {
 	MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 	MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
@@ -255,23 +283,81 @@ int board_early_init_f(void)
 	return 0;
 }
 
-static struct fsl_esdhc_cfg usdhc_cfg[1] = {
+static struct fsl_esdhc_cfg usdhc_cfg[3] = {
+	{USDHC2_BASE_ADDR, 0, 4},
+	{USDHC3_BASE_ADDR},
 	{USDHC4_BASE_ADDR},
 };
 
+#define USDHC3_CD_GPIO	IMX_GPIO_NR(2, 10)
+#define USDHC3_PWR_GPIO	IMX_GPIO_NR(2, 11)
+#define USDHC4_CD_GPIO	IMX_GPIO_NR(6, 21)
+
 int board_mmc_getcd(struct mmc *mmc)
 {
-	return 1;	/* Assume boot SD always present */
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC2_BASE_ADDR:
+		ret = 1; /* Assume uSDHC2 is always present */
+		break;
+	case USDHC3_BASE_ADDR:
+		ret = !gpio_get_value(USDHC3_CD_GPIO);
+		break;
+	case USDHC4_BASE_ADDR:
+		ret = !gpio_get_value(USDHC4_CD_GPIO);
+		break;
+	}
+
+	return ret;
 }
 
 int board_mmc_init(bd_t *bis)
 {
-	imx_iomux_v3_setup_multiple_pads(usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+	int i;
 
-	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
-	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-boot device node)    (Physical Port)
+	 * mmc0                    USDHC2
+	 * mmc1                    USDHC3
+	 * mmc2                    USDHC4
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+			break;
+		case 1:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+			gpio_direction_input(USDHC3_CD_GPIO);
+			gpio_direction_output(USDHC3_PWR_GPIO, 1);
+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+			break;
+		case 2:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+			gpio_direction_input(USDHC4_CD_GPIO);
+			usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers"
+				"(%d) than supported by the board\n", i + 1);
+			return 0;
+			}
+
+			if (fsl_esdhc_initialize(bis, &usdhc_cfg[i]))
+				printf("Warning: failed to initialize mmc dev %d\n", i);
+	}
+
+	return 0;
 }
 
+
 int board_init(void)
 {
 	/* Address of boot parameters */
diff --git a/include/configs/mx6sxsabresd.h b/include/configs/mx6sxsabresd.h
index e02ea18..5bbc8da 100644
--- a/include/configs/mx6sxsabresd.h
+++ b/include/configs/mx6sxsabresd.h
@@ -214,7 +214,6 @@
 #define CONFIG_ENV_OFFSET		(6 * SZ_64K)
 #define CONFIG_ENV_SIZE			SZ_8K
 #define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_SYS_MMC_ENV_DEV		0
 
 #define CONFIG_OF_LIBFDT
 #define CONFIG_CMD_BOOTZ
@@ -223,4 +222,9 @@
 #define CONFIG_CMD_CACHE
 #endif
 
+#define CONFIG_SYS_FSL_USDHC_NUM	3
+#if defined(CONFIG_ENV_IS_IN_MMC)
+#define CONFIG_SYS_MMC_ENV_DEV		2  /*USDHC4*/
+#endif
+
 #endif				/* __CONFIG_H */
-- 
1.7.4.1