[U-Boot] [PATCH v4 14/29] dm: exynos: Convert SPI to driver model
Simon Glass
sjg at chromium.org
Tue Oct 14 07:42:01 CEST 2014
Move the exynos SPI driver over to driver model. This removes quite a bit
of boilerplate from the driver, although it adds some for driver model.
A few device tree additions are needed to make the SPI flash available.
Signed-off-by: Simon Glass <sjg at chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki at gmail.com>
---
Changes in v4: None
Changes in v3:
- Add implementation/comment for the cs_info() method
- Use an explicit chip select value instead of reusing device sequence number
Changes in v2:
- Add additional debug() statements
- Adjust xfer() method for new API
- Use 'bus' instead of 'dev' to distinguish bus from slave
arch/arm/dts/exynos5250-snow.dts | 8 +
arch/arm/dts/exynos5420-peach-pit.dts | 1 +
board/samsung/common/board.c | 3 -
drivers/spi/exynos_spi.c | 513 ++++++++++++----------------------
include/configs/exynos-common.h | 1 +
5 files changed, 190 insertions(+), 336 deletions(-)
diff --git a/arch/arm/dts/exynos5250-snow.dts b/arch/arm/dts/exynos5250-snow.dts
index 2003412..6fd9275 100644
--- a/arch/arm/dts/exynos5250-snow.dts
+++ b/arch/arm/dts/exynos5250-snow.dts
@@ -53,6 +53,14 @@
};
};
+ spi at 12d30000 {
+ spi-max-frequency = <50000000>;
+ firmware_storage_spi: flash at 0 {
+ compatible = "spi-flash";
+ reg = <0>;
+ };
+ };
+
spi at 131b0000 {
spi-max-frequency = <1000000>;
spi-deactivate-delay = <100>;
diff --git a/arch/arm/dts/exynos5420-peach-pit.dts b/arch/arm/dts/exynos5420-peach-pit.dts
index c4c4b8e..fde863d 100644
--- a/arch/arm/dts/exynos5420-peach-pit.dts
+++ b/arch/arm/dts/exynos5420-peach-pit.dts
@@ -140,6 +140,7 @@
spi at 12d30000 { /* spi1 */
spi-max-frequency = <50000000>;
firmware_storage_spi: flash at 0 {
+ compatible = "spi-flash";
reg = <0>;
/*
diff --git a/board/samsung/common/board.c b/board/samsung/common/board.c
index c119641..e1fc123 100644
--- a/board/samsung/common/board.c
+++ b/board/samsung/common/board.c
@@ -87,9 +87,6 @@ int board_init(void)
boot_temp_check();
#endif
-#ifdef CONFIG_EXYNOS_SPI
- spi_init();
-#endif
return exynos_init();
}
diff --git a/drivers/spi/exynos_spi.c b/drivers/spi/exynos_spi.c
index 2969184..f078973 100644
--- a/drivers/spi/exynos_spi.c
+++ b/drivers/spi/exynos_spi.c
@@ -6,6 +6,8 @@
*/
#include <common.h>
+#include <dm.h>
+#include <errno.h>
#include <malloc.h>
#include <spi.h>
#include <fdtdec.h>
@@ -19,176 +21,35 @@
DECLARE_GLOBAL_DATA_PTR;
-/* Information about each SPI controller */
-struct spi_bus {
+struct exynos_spi_platdata {
enum periph_id periph_id;
s32 frequency; /* Default clock frequency, -1 for none */
struct exynos_spi *regs;
- int inited; /* 1 if this bus is ready for use */
- int node;
uint deactivate_delay_us; /* Delay to wait after deactivate */
};
-/* A list of spi buses that we know about */
-static struct spi_bus spi_bus[EXYNOS5_SPI_NUM_CONTROLLERS];
-static unsigned int bus_count;
-
-struct exynos_spi_slave {
- struct spi_slave slave;
+struct exynos_spi_priv {
struct exynos_spi *regs;
unsigned int freq; /* Default frequency */
unsigned int mode;
enum periph_id periph_id; /* Peripheral ID for this device */
unsigned int fifo_size;
int skip_preamble;
- struct spi_bus *bus; /* Pointer to our SPI bus info */
ulong last_transaction_us; /* Time of last transaction end */
};
-static struct spi_bus *spi_get_bus(unsigned dev_index)
-{
- if (dev_index < bus_count)
- return &spi_bus[dev_index];
- debug("%s: invalid bus %d", __func__, dev_index);
-
- return NULL;
-}
-
-static inline struct exynos_spi_slave *to_exynos_spi(struct spi_slave *slave)
-{
- return container_of(slave, struct exynos_spi_slave, slave);
-}
-
-/**
- * Setup the driver private data
- *
- * @param bus ID of the bus that the slave is attached to
- * @param cs ID of the chip select connected to the slave
- * @param max_hz Required spi frequency
- * @param mode Required spi mode (clk polarity, clk phase and
- * master or slave)
- * @return new device or NULL
- */
-struct spi_slave *spi_setup_slave(unsigned int busnum, unsigned int cs,
- unsigned int max_hz, unsigned int mode)
-{
- struct exynos_spi_slave *spi_slave;
- struct spi_bus *bus;
-
- if (!spi_cs_is_valid(busnum, cs)) {
- debug("%s: Invalid bus/chip select %d, %d\n", __func__,
- busnum, cs);
- return NULL;
- }
-
- spi_slave = spi_alloc_slave(struct exynos_spi_slave, busnum, cs);
- if (!spi_slave) {
- debug("%s: Could not allocate spi_slave\n", __func__);
- return NULL;
- }
-
- bus = &spi_bus[busnum];
- spi_slave->bus = bus;
- spi_slave->regs = bus->regs;
- spi_slave->mode = mode;
- spi_slave->periph_id = bus->periph_id;
- if (bus->periph_id == PERIPH_ID_SPI1 ||
- bus->periph_id == PERIPH_ID_SPI2)
- spi_slave->fifo_size = 64;
- else
- spi_slave->fifo_size = 256;
-
- spi_slave->skip_preamble = 0;
- spi_slave->last_transaction_us = timer_get_us();
-
- spi_slave->freq = bus->frequency;
- if (max_hz)
- spi_slave->freq = min(max_hz, spi_slave->freq);
-
- return &spi_slave->slave;
-}
-
-/**
- * Free spi controller
- *
- * @param slave Pointer to spi_slave to which controller has to
- * communicate with
- */
-void spi_free_slave(struct spi_slave *slave)
-{
- struct exynos_spi_slave *spi_slave = to_exynos_spi(slave);
-
- free(spi_slave);
-}
-
/**
* Flush spi tx, rx fifos and reset the SPI controller
*
- * @param slave Pointer to spi_slave to which controller has to
- * communicate with
+ * @param regs Pointer to SPI registers
*/
-static void spi_flush_fifo(struct spi_slave *slave)
+static void spi_flush_fifo(struct exynos_spi *regs)
{
- struct exynos_spi_slave *spi_slave = to_exynos_spi(slave);
- struct exynos_spi *regs = spi_slave->regs;
-
clrsetbits_le32(®s->ch_cfg, SPI_CH_HS_EN, SPI_CH_RST);
clrbits_le32(®s->ch_cfg, SPI_CH_RST);
setbits_le32(®s->ch_cfg, SPI_TX_CH_ON | SPI_RX_CH_ON);
}
-/**
- * Initialize the spi base registers, set the required clock frequency and
- * initialize the gpios
- *
- * @param slave Pointer to spi_slave to which controller has to
- * communicate with
- * @return zero on success else a negative value
- */
-int spi_claim_bus(struct spi_slave *slave)
-{
- struct exynos_spi_slave *spi_slave = to_exynos_spi(slave);
- struct exynos_spi *regs = spi_slave->regs;
- u32 reg = 0;
- int ret;
-
- ret = set_spi_clk(spi_slave->periph_id,
- spi_slave->freq);
- if (ret < 0) {
- debug("%s: Failed to setup spi clock\n", __func__);
- return ret;
- }
-
- exynos_pinmux_config(spi_slave->periph_id, PINMUX_FLAG_NONE);
-
- spi_flush_fifo(slave);
-
- reg = readl(®s->ch_cfg);
- reg &= ~(SPI_CH_CPHA_B | SPI_CH_CPOL_L);
-
- if (spi_slave->mode & SPI_CPHA)
- reg |= SPI_CH_CPHA_B;
-
- if (spi_slave->mode & SPI_CPOL)
- reg |= SPI_CH_CPOL_L;
-
- writel(reg, ®s->ch_cfg);
- writel(SPI_FB_DELAY_180, ®s->fb_clk);
-
- return 0;
-}
-
-/**
- * Reset the spi H/W and flush the tx and rx fifos
- *
- * @param slave Pointer to spi_slave to which controller has to
- * communicate with
- */
-void spi_release_bus(struct spi_slave *slave)
-{
- spi_flush_fifo(slave);
-}
-
static void spi_get_fifo_levels(struct exynos_spi *regs,
int *rx_lvl, int *tx_lvl)
{
@@ -208,6 +69,8 @@ static void spi_get_fifo_levels(struct exynos_spi *regs,
*/
static void spi_request_bytes(struct exynos_spi *regs, int count, int step)
{
+ debug("%s: regs=%p, count=%d, step=%d\n", __func__, regs, count, step);
+
/* For word address we need to swap bytes */
if (step == 4) {
setbits_le32(®s->mode_cfg,
@@ -230,10 +93,10 @@ static void spi_request_bytes(struct exynos_spi *regs, int count, int step)
writel(count | SPI_PACKET_CNT_EN, ®s->pkt_cnt);
}
-static int spi_rx_tx(struct exynos_spi_slave *spi_slave, int todo,
+static int spi_rx_tx(struct exynos_spi_priv *priv, int todo,
void **dinp, void const **doutp, unsigned long flags)
{
- struct exynos_spi *regs = spi_slave->regs;
+ struct exynos_spi *regs = priv->regs;
uchar *rxp = *dinp;
const uchar *txp = *doutp;
int rx_lvl, tx_lvl;
@@ -245,8 +108,8 @@ static int spi_rx_tx(struct exynos_spi_slave *spi_slave, int todo,
out_bytes = in_bytes = todo;
- stopping = spi_slave->skip_preamble && (flags & SPI_XFER_END) &&
- !(spi_slave->mode & SPI_SLAVE);
+ stopping = priv->skip_preamble && (flags & SPI_XFER_END) &&
+ !(priv->mode & SPI_SLAVE);
/*
* Try to transfer words if we can. This helps read performance at
@@ -254,7 +117,7 @@ static int spi_rx_tx(struct exynos_spi_slave *spi_slave, int todo,
*/
step = 1;
if (!((todo | (uintptr_t)rxp | (uintptr_t)txp) & 3) &&
- !spi_slave->skip_preamble)
+ !priv->skip_preamble)
step = 4;
/*
@@ -279,7 +142,7 @@ static int spi_rx_tx(struct exynos_spi_slave *spi_slave, int todo,
* Don't completely fill the txfifo, since we don't want our
* rxfifo to overflow, and it may already contain data.
*/
- while (tx_lvl < spi_slave->fifo_size/2 && out_bytes) {
+ while (tx_lvl < priv->fifo_size/2 && out_bytes) {
if (!txp)
temp = -1;
else if (step == 4)
@@ -295,9 +158,9 @@ static int spi_rx_tx(struct exynos_spi_slave *spi_slave, int todo,
if (rx_lvl >= step) {
while (rx_lvl >= step) {
temp = readl(®s->rx_data);
- if (spi_slave->skip_preamble) {
+ if (priv->skip_preamble) {
if (temp == SPI_PREAMBLE_END_BYTE) {
- spi_slave->skip_preamble = 0;
+ priv->skip_preamble = 0;
stopping = 0;
}
} else {
@@ -326,7 +189,7 @@ static int spi_rx_tx(struct exynos_spi_slave *spi_slave, int todo,
txp = NULL;
spi_request_bytes(regs, toread, step);
}
- if (spi_slave->skip_preamble && get_timer(start) > 100) {
+ if (priv->skip_preamble && get_timer(start) > 100) {
printf("SPI timeout: in_bytes=%d, out_bytes=%d, ",
in_bytes, out_bytes);
return -1;
@@ -340,94 +203,29 @@ static int spi_rx_tx(struct exynos_spi_slave *spi_slave, int todo,
}
/**
- * Transfer and receive data
- *
- * @param slave Pointer to spi_slave to which controller has to
- * communicate with
- * @param bitlen No of bits to tranfer or receive
- * @param dout Pointer to transfer buffer
- * @param din Pointer to receive buffer
- * @param flags Flags for transfer begin and end
- * @return zero on success else a negative value
- */
-int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
- void *din, unsigned long flags)
-{
- struct exynos_spi_slave *spi_slave = to_exynos_spi(slave);
- int upto, todo;
- int bytelen;
- int ret = 0;
-
- /* spi core configured to do 8 bit transfers */
- if (bitlen % 8) {
- debug("Non byte aligned SPI transfer.\n");
- return -1;
- }
-
- /* Start the transaction, if necessary. */
- if ((flags & SPI_XFER_BEGIN))
- spi_cs_activate(slave);
-
- /*
- * Exynos SPI limits each transfer to 65535 transfers. To keep
- * things simple, allow a maximum of 65532 bytes. We could allow
- * more in word mode, but the performance difference is small.
- */
- bytelen = bitlen / 8;
- for (upto = 0; !ret && upto < bytelen; upto += todo) {
- todo = min(bytelen - upto, (1 << 16) - 4);
- ret = spi_rx_tx(spi_slave, todo, &din, &dout, flags);
- if (ret)
- break;
- }
-
- /* Stop the transaction, if necessary. */
- if ((flags & SPI_XFER_END) && !(spi_slave->mode & SPI_SLAVE)) {
- spi_cs_deactivate(slave);
- if (spi_slave->skip_preamble) {
- assert(!spi_slave->skip_preamble);
- debug("Failed to complete premable transaction\n");
- ret = -1;
- }
- }
-
- return ret;
-}
-
-/**
- * Validates the bus and chip select numbers
- *
- * @param bus ID of the bus that the slave is attached to
- * @param cs ID of the chip select connected to the slave
- * @return one on success else zero
- */
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
- return spi_get_bus(bus) && cs == 0;
-}
-
-/**
* Activate the CS by driving it LOW
*
* @param slave Pointer to spi_slave to which controller has to
* communicate with
*/
-void spi_cs_activate(struct spi_slave *slave)
+static void spi_cs_activate(struct udevice *dev)
{
- struct exynos_spi_slave *spi_slave = to_exynos_spi(slave);
+ struct udevice *bus = dev->parent;
+ struct exynos_spi_platdata *pdata = dev_get_platdata(bus);
+ struct exynos_spi_priv *priv = dev_get_priv(bus);
/* If it's too soon to do another transaction, wait */
- if (spi_slave->bus->deactivate_delay_us &&
- spi_slave->last_transaction_us) {
+ if (pdata->deactivate_delay_us &&
+ priv->last_transaction_us) {
ulong delay_us; /* The delay completed so far */
- delay_us = timer_get_us() - spi_slave->last_transaction_us;
- if (delay_us < spi_slave->bus->deactivate_delay_us)
- udelay(spi_slave->bus->deactivate_delay_us - delay_us);
+ delay_us = timer_get_us() - priv->last_transaction_us;
+ if (delay_us < pdata->deactivate_delay_us)
+ udelay(pdata->deactivate_delay_us - delay_us);
}
- clrbits_le32(&spi_slave->regs->cs_reg, SPI_SLAVE_SIG_INACT);
- debug("Activate CS, bus %d\n", spi_slave->slave.bus);
- spi_slave->skip_preamble = spi_slave->mode & SPI_PREAMBLE;
+ clrbits_le32(&priv->regs->cs_reg, SPI_SLAVE_SIG_INACT);
+ debug("Activate CS, bus '%s'\n", bus->name);
+ priv->skip_preamble = priv->mode & SPI_PREAMBLE;
}
/**
@@ -436,148 +234,197 @@ void spi_cs_activate(struct spi_slave *slave)
* @param slave Pointer to spi_slave to which controller has to
* communicate with
*/
-void spi_cs_deactivate(struct spi_slave *slave)
+static void spi_cs_deactivate(struct udevice *dev)
{
- struct exynos_spi_slave *spi_slave = to_exynos_spi(slave);
+ struct udevice *bus = dev->parent;
+ struct exynos_spi_platdata *pdata = dev_get_platdata(bus);
+ struct exynos_spi_priv *priv = dev_get_priv(bus);
- setbits_le32(&spi_slave->regs->cs_reg, SPI_SLAVE_SIG_INACT);
+ setbits_le32(&priv->regs->cs_reg, SPI_SLAVE_SIG_INACT);
/* Remember time of this transaction so we can honour the bus delay */
- if (spi_slave->bus->deactivate_delay_us)
- spi_slave->last_transaction_us = timer_get_us();
+ if (pdata->deactivate_delay_us)
+ priv->last_transaction_us = timer_get_us();
- debug("Deactivate CS, bus %d\n", spi_slave->slave.bus);
+ debug("Deactivate CS, bus '%s'\n", bus->name);
}
-static inline struct exynos_spi *get_spi_base(int dev_index)
+static int exynos_spi_ofdata_to_platdata(struct udevice *bus)
{
- if (dev_index < 3)
- return (struct exynos_spi *)samsung_get_base_spi() + dev_index;
- else
- return (struct exynos_spi *)samsung_get_base_spi_isp() +
- (dev_index - 3);
-}
+ struct exynos_spi_platdata *plat = bus->platdata;
+ const void *blob = gd->fdt_blob;
+ int node = bus->of_offset;
-/*
- * Read the SPI config from the device tree node.
- *
- * @param blob FDT blob to read from
- * @param node Node offset to read from
- * @param bus SPI bus structure to fill with information
- * @return 0 if ok, or -FDT_ERR_NOTFOUND if something was missing
- */
-#ifdef CONFIG_OF_CONTROL
-static int spi_get_config(const void *blob, int node, struct spi_bus *bus)
-{
- bus->node = node;
- bus->regs = (struct exynos_spi *)fdtdec_get_addr(blob, node, "reg");
- bus->periph_id = pinmux_decode_periph_id(blob, node);
+ plat->regs = (struct exynos_spi *)fdtdec_get_addr(blob, node, "reg");
+ plat->periph_id = pinmux_decode_periph_id(blob, node);
- if (bus->periph_id == PERIPH_ID_NONE) {
+ if (plat->periph_id == PERIPH_ID_NONE) {
debug("%s: Invalid peripheral ID %d\n", __func__,
- bus->periph_id);
+ plat->periph_id);
return -FDT_ERR_NOTFOUND;
}
/* Use 500KHz as a suitable default */
- bus->frequency = fdtdec_get_int(blob, node, "spi-max-frequency",
+ plat->frequency = fdtdec_get_int(blob, node, "spi-max-frequency",
500000);
- bus->deactivate_delay_us = fdtdec_get_int(blob, node,
+ plat->deactivate_delay_us = fdtdec_get_int(blob, node,
"spi-deactivate-delay", 0);
+ debug("%s: regs=%p, periph_id=%d, max-frequency=%d, deactivate_delay=%d\n",
+ __func__, plat->regs, plat->periph_id, plat->frequency,
+ plat->deactivate_delay_us);
return 0;
}
-/*
- * Process a list of nodes, adding them to our list of SPI ports.
- *
- * @param blob fdt blob
- * @param node_list list of nodes to process (any <=0 are ignored)
- * @param count number of nodes to process
- * @param is_dvc 1 if these are DVC ports, 0 if standard I2C
- * @return 0 if ok, -1 on error
- */
-static int process_nodes(const void *blob, int node_list[], int count)
+static int exynos_spi_probe(struct udevice *bus)
{
- int i;
+ struct exynos_spi_platdata *plat = dev_get_platdata(bus);
+ struct exynos_spi_priv *priv = dev_get_priv(bus);
- /* build the i2c_controllers[] for each controller */
- for (i = 0; i < count; i++) {
- int node = node_list[i];
- struct spi_bus *bus;
+ priv->regs = plat->regs;
+ if (plat->periph_id == PERIPH_ID_SPI1 ||
+ plat->periph_id == PERIPH_ID_SPI2)
+ priv->fifo_size = 64;
+ else
+ priv->fifo_size = 256;
- if (node <= 0)
- continue;
+ priv->skip_preamble = 0;
+ priv->last_transaction_us = timer_get_us();
+ priv->freq = plat->frequency;
+ priv->periph_id = plat->periph_id;
- bus = &spi_bus[i];
- if (spi_get_config(blob, node, bus)) {
- printf("exynos spi_init: failed to decode bus %d\n",
- i);
- return -1;
- }
+ return 0;
+}
- debug("spi: controller bus %d at %p, periph_id %d\n",
- i, bus->regs, bus->periph_id);
- bus->inited = 1;
- bus_count++;
- }
+static int exynos_spi_claim_bus(struct udevice *bus)
+{
+ struct exynos_spi_priv *priv = dev_get_priv(bus);
+
+ exynos_pinmux_config(priv->periph_id, PINMUX_FLAG_NONE);
+ spi_flush_fifo(priv->regs);
+
+ writel(SPI_FB_DELAY_180, &priv->regs->fb_clk);
return 0;
}
-#endif
-/**
- * Set up a new SPI slave for an fdt node
- *
- * @param blob Device tree blob
- * @param node SPI peripheral node to use
- * @return 0 if ok, -1 on error
- */
-struct spi_slave *spi_setup_slave_fdt(const void *blob, int slave_node,
- int spi_node)
+static int exynos_spi_release_bus(struct udevice *bus)
{
- struct spi_bus *bus;
- unsigned int i;
+ struct exynos_spi_priv *priv = dev_get_priv(bus);
+
+ spi_flush_fifo(priv->regs);
+
+ return 0;
+}
+
+static int exynos_spi_xfer(struct udevice *dev, unsigned int bitlen,
+ const void *dout, void *din, unsigned long flags)
+{
+ struct udevice *bus = dev->parent;
+ struct exynos_spi_priv *priv = dev_get_priv(bus);
+ int upto, todo;
+ int bytelen;
+ int ret = 0;
+
+ /* spi core configured to do 8 bit transfers */
+ if (bitlen % 8) {
+ debug("Non byte aligned SPI transfer.\n");
+ return -1;
+ }
+
+ /* Start the transaction, if necessary. */
+ if ((flags & SPI_XFER_BEGIN))
+ spi_cs_activate(dev);
+
+ /*
+ * Exynos SPI limits each transfer to 65535 transfers. To keep
+ * things simple, allow a maximum of 65532 bytes. We could allow
+ * more in word mode, but the performance difference is small.
+ */
+ bytelen = bitlen / 8;
+ for (upto = 0; !ret && upto < bytelen; upto += todo) {
+ todo = min(bytelen - upto, (1 << 16) - 4);
+ ret = spi_rx_tx(priv, todo, &din, &dout, flags);
+ if (ret)
+ break;
+ }
- for (i = 0, bus = spi_bus; i < bus_count; i++, bus++) {
- if (bus->node == spi_node)
- return spi_base_setup_slave_fdt(blob, i, slave_node);
+ /* Stop the transaction, if necessary. */
+ if ((flags & SPI_XFER_END) && !(priv->mode & SPI_SLAVE)) {
+ spi_cs_deactivate(dev);
+ if (priv->skip_preamble) {
+ assert(!priv->skip_preamble);
+ debug("Failed to complete premable transaction\n");
+ ret = -1;
+ }
}
- debug("%s: Failed to find bus node %d\n", __func__, spi_node);
- return NULL;
+ return ret;
}
-/* Sadly there is no error return from this function */
-void spi_init(void)
+static int exynos_spi_set_speed(struct udevice *bus, uint speed)
{
- int count;
+ struct exynos_spi_platdata *plat = bus->platdata;
+ struct exynos_spi_priv *priv = dev_get_priv(bus);
+ int ret;
-#ifdef CONFIG_OF_CONTROL
- int node_list[EXYNOS5_SPI_NUM_CONTROLLERS];
- const void *blob = gd->fdt_blob;
+ if (speed > plat->frequency)
+ speed = plat->frequency;
+ ret = set_spi_clk(priv->periph_id, speed);
+ if (ret)
+ return ret;
+ priv->freq = speed;
+ debug("%s: regs=%p, speed=%d\n", __func__, priv->regs, priv->freq);
+
+ return 0;
+}
- count = fdtdec_find_aliases_for_id(blob, "spi",
- COMPAT_SAMSUNG_EXYNOS_SPI, node_list,
- EXYNOS5_SPI_NUM_CONTROLLERS);
- if (process_nodes(blob, node_list, count))
- return;
+static int exynos_spi_set_mode(struct udevice *bus, uint mode)
+{
+ struct exynos_spi_priv *priv = dev_get_priv(bus);
+ uint32_t reg;
-#else
- struct spi_bus *bus;
+ reg = readl(&priv->regs->ch_cfg);
+ reg &= ~(SPI_CH_CPHA_B | SPI_CH_CPOL_L);
- for (count = 0; count < EXYNOS5_SPI_NUM_CONTROLLERS; count++) {
- bus = &spi_bus[count];
- bus->regs = get_spi_base(count);
- bus->periph_id = PERIPH_ID_SPI0 + count;
+ if (mode & SPI_CPHA)
+ reg |= SPI_CH_CPHA_B;
- /* Although Exynos5 supports upto 50Mhz speed,
- * we are setting it to 10Mhz for safe side
- */
- bus->frequency = 10000000;
- bus->inited = 1;
- bus->node = 0;
- bus_count = EXYNOS5_SPI_NUM_CONTROLLERS;
- }
-#endif
+ if (mode & SPI_CPOL)
+ reg |= SPI_CH_CPOL_L;
+
+ writel(reg, &priv->regs->ch_cfg);
+ priv->mode = mode;
+ debug("%s: regs=%p, mode=%d\n", __func__, priv->regs, priv->mode);
+
+ return 0;
}
+
+static const struct dm_spi_ops exynos_spi_ops = {
+ .claim_bus = exynos_spi_claim_bus,
+ .release_bus = exynos_spi_release_bus,
+ .xfer = exynos_spi_xfer,
+ .set_speed = exynos_spi_set_speed,
+ .set_mode = exynos_spi_set_mode,
+ /*
+ * cs_info is not needed, since we require all chip selects to be
+ * in the device tree explicitly
+ */
+};
+
+static const struct udevice_id exynos_spi_ids[] = {
+ { .compatible = "samsung,exynos-spi" },
+ { }
+};
+
+U_BOOT_DRIVER(exynos_spi) = {
+ .name = "exynos_spi",
+ .id = UCLASS_SPI,
+ .of_match = exynos_spi_ids,
+ .ops = &exynos_spi_ops,
+ .ofdata_to_platdata = exynos_spi_ofdata_to_platdata,
+ .platdata_auto_alloc_size = sizeof(struct exynos_spi_platdata),
+ .priv_auto_alloc_size = sizeof(struct exynos_spi_priv),
+ .per_child_auto_alloc_size = sizeof(struct spi_slave),
+ .probe = exynos_spi_probe,
+};
diff --git a/include/configs/exynos-common.h b/include/configs/exynos-common.h
index 34a162d..eb6745e 100644
--- a/include/configs/exynos-common.h
+++ b/include/configs/exynos-common.h
@@ -21,6 +21,7 @@
#define CONFIG_CMD_DM
#define CONFIG_DM_GPIO
#define CONFIG_DM_SERIAL
+#define CONFIG_DM_SPI
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_DISPLAY_CPUINFO
--
2.1.0.rc2.206.gedb03e5
More information about the U-Boot
mailing list