[U-Boot] [PATCH 01/25] ppc: Zap ICU862 board
Marek Vasut
marex at denx.de
Mon Oct 20 03:48:02 CEST 2014
This board is the only user of CONFIG_SYS_EEPROM_X40430 , remove
it so the EEPROM command code can be cleansed of the related code
as well.
Signed-off-by: Marek Vasut <marex at denx.de>
Cc: Masahiro Yamada <yamada.m at jp.panasonic.com>
Cc: Tom Rini <trini at ti.com>
Cc: Wolfgang Denk <wd at denx.de>
Cc: Simon Glass <sjg at chromium.org>
Cc: Heiko Schocher <hs at denx.de>
---
arch/powerpc/cpu/mpc8xx/Kconfig | 4 -
arch/powerpc/cpu/mpc8xx/cpu_init.c | 1 -
arch/powerpc/cpu/mpc8xx/fec.c | 40 +--
board/icu862/Kconfig | 9 -
board/icu862/MAINTAINERS | 7 -
board/icu862/Makefile | 8 -
board/icu862/flash.c | 575 -------------------------------------
board/icu862/icu862.c | 199 -------------
board/icu862/pcmcia.c | 262 -----------------
board/icu862/u-boot.lds | 82 ------
board/icu862/u-boot.lds.debug | 122 --------
configs/ICU862_100MHz_defconfig | 4 -
configs/ICU862_defconfig | 3 -
include/commproc.h | 10 -
include/configs/ICU862.h | 443 ----------------------------
include/pcmcia.h | 2 -
include/status_led.h | 19 --
17 files changed, 1 insertion(+), 1789 deletions(-)
delete mode 100644 board/icu862/Kconfig
delete mode 100644 board/icu862/MAINTAINERS
delete mode 100644 board/icu862/Makefile
delete mode 100644 board/icu862/flash.c
delete mode 100644 board/icu862/icu862.c
delete mode 100644 board/icu862/pcmcia.c
delete mode 100644 board/icu862/u-boot.lds
delete mode 100644 board/icu862/u-boot.lds.debug
delete mode 100644 configs/ICU862_100MHz_defconfig
delete mode 100644 configs/ICU862_defconfig
delete mode 100644 include/configs/ICU862.h
diff --git a/arch/powerpc/cpu/mpc8xx/Kconfig b/arch/powerpc/cpu/mpc8xx/Kconfig
index f1dca90..171bee9 100644
--- a/arch/powerpc/cpu/mpc8xx/Kconfig
+++ b/arch/powerpc/cpu/mpc8xx/Kconfig
@@ -16,9 +16,6 @@ config TARGET_ESTEEM192E
config TARGET_HERMES
bool "Support hermes"
-config TARGET_ICU862
- bool "Support ICU862"
-
config TARGET_IP860
bool "Support IP860"
@@ -124,7 +121,6 @@ source "board/eltec/mhpc/Kconfig"
source "board/emk/top860/Kconfig"
source "board/esteem192e/Kconfig"
source "board/hermes/Kconfig"
-source "board/icu862/Kconfig"
source "board/ip860/Kconfig"
source "board/ivm/Kconfig"
source "board/kup/kup4k/Kconfig"
diff --git a/arch/powerpc/cpu/mpc8xx/cpu_init.c b/arch/powerpc/cpu/mpc8xx/cpu_init.c
index 90c7e61..b8dc14d 100644
--- a/arch/powerpc/cpu/mpc8xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc8xx/cpu_init.c
@@ -126,7 +126,6 @@ void cpu_init_f (volatile immap_t * immr)
*/
#if defined(CONFIG_HERMES) || \
- defined(CONFIG_ICU862) || \
defined(CONFIG_IP860) || \
defined(CONFIG_IVML24) || \
defined(CONFIG_IVMS8) || \
diff --git a/arch/powerpc/cpu/mpc8xx/fec.c b/arch/powerpc/cpu/mpc8xx/fec.c
index d12b3df..22b8ec7 100644
--- a/arch/powerpc/cpu/mpc8xx/fec.c
+++ b/arch/powerpc/cpu/mpc8xx/fec.c
@@ -205,11 +205,7 @@ static int fec_send(struct eth_device *dev, void *packet, int length)
j = 0;
while ((rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY) && (j<TOUT_LOOP)) {
-#if defined(CONFIG_ICU862)
- udelay(10);
-#else
udelay(1);
-#endif
j++;
}
if (j>=TOUT_LOOP) {
@@ -424,7 +420,7 @@ static void fec_pin_init(int fecidx)
#endif /* !CONFIG_RMII */
-#elif !defined(CONFIG_ICU862)
+#else
/*
* Configure all of port D for MII.
*/
@@ -437,42 +433,8 @@ static void fec_pin_init(int fecidx)
immr->im_ioport.iop_pddir = 0x1c58; /* Pre rev. D */
else
immr->im_ioport.iop_pddir = 0x1fff; /* Rev. D and later */
-#else
- /*
- * Configure port A for MII.
- */
-
-#if defined(CONFIG_ICU862) && defined(CONFIG_SYS_DISCOVER_PHY)
-
- /*
- * On the ICU862 board the MII-MDC pin is routed to PD8 pin
- * * of CPU, so for this board we need to configure Utopia and
- * * enable PD8 to MII-MDC function
- */
- immr->im_ioport.iop_pdpar |= 0x4080;
#endif
- /*
- * Has Utopia been configured?
- */
- if (immr->im_ioport.iop_pdpar & (0x8000 >> 1)) {
- /*
- * YES - Use MUXED mode for UTOPIA bus.
- * This frees Port A for use by MII (see 862UM table 41-6).
- */
- immr->im_ioport.utmode &= ~0x80;
- } else {
- /*
- * NO - set SPLIT mode for UTOPIA bus.
- *
- * This doesn't really effect UTOPIA (which isn't
- * enabled anyway) but just tells the 862
- * to use port A for MII (see 862UM table 41-6).
- */
- immr->im_ioport.utmode |= 0x80;
- }
-#endif /* !defined(CONFIG_ICU862) */
-
#endif /* CONFIG_ETHER_ON_FEC1 */
} else if (fecidx == 1) {
diff --git a/board/icu862/Kconfig b/board/icu862/Kconfig
deleted file mode 100644
index da11d7b..0000000
--- a/board/icu862/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_ICU862
-
-config SYS_BOARD
- default "icu862"
-
-config SYS_CONFIG_NAME
- default "ICU862"
-
-endif
diff --git a/board/icu862/MAINTAINERS b/board/icu862/MAINTAINERS
deleted file mode 100644
index 7fe16d1..0000000
--- a/board/icu862/MAINTAINERS
+++ /dev/null
@@ -1,7 +0,0 @@
-ICU862 BOARD
-M: Wolfgang Denk <wd at denx.de>
-S: Maintained
-F: board/icu862/
-F: include/configs/ICU862.h
-F: configs/ICU862_defconfig
-F: configs/ICU862_100MHz_defconfig
diff --git a/board/icu862/Makefile b/board/icu862/Makefile
deleted file mode 100644
index 263f21b..0000000
--- a/board/icu862/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = icu862.o flash.o pcmcia.o
diff --git a/board/icu862/flash.c b/board/icu862/flash.c
deleted file mode 100644
index a84ab99..0000000
--- a/board/icu862/flash.c
+++ /dev/null
@@ -1,575 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-# ifndef CONFIG_ENV_ADDR
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-# endif
-# ifndef CONFIG_ENV_SIZE
-# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-# endif
-# ifndef CONFIG_ENV_SECT_SIZE
-# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-# endif
-#endif
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_long *addr, flash_info_t *info);
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-static void flash_get_offsets (ulong base, flash_info_t *info);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- unsigned long size_b0;
- int i;
-
- /* Init: no FLASHes known */
- for (i=0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i)
- flash_info[i].flash_id = FLASH_UNKNOWN;
-
- /* Static FLASH Bank configuration here - FIXME XXX */
-
- size_b0 = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
-
- if (flash_info[0].flash_id == FLASH_UNKNOWN) {
- printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
- size_b0,
- size_b0 >> 20);
- }
-
- /* Remap FLASH according to real size */
- memctl->memc_or0 = CONFIG_SYS_OR_TIMING_FLASH | (-size_b0 & OR_AM_MSK);
- memctl->memc_br0 = (CONFIG_SYS_FLASH_BASE & BR_BA_MSK) | BR_MS_GPCM | BR_V;
-
- /* Re-do sizing to get full correct info */
- size_b0 = flash_get_size((vu_long *)CONFIG_SYS_FLASH_BASE, &flash_info[0]);
-
- flash_get_offsets (CONFIG_SYS_FLASH_BASE, &flash_info[0]);
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1,
- &flash_info[0]);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR+CONFIG_ENV_SIZE-1,
- &flash_info[0]);
-#endif
-
- /* ICU862 Board has only one Flash Bank */
- flash_info[0].size = size_b0;
-
- return size_b0;
-
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t *info)
-{
- int i;
-
- /* set up sector start address table */
- if (((info->flash_id & FLASH_TYPEMASK) == FLASH_AM040) ||
- ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM033C)) {
- /* set sector offsets for uniform sector type */
- for (i = 0; i < info->sector_count; i++) {
- info->start[i] = base + (i * 0x00040000);
- }
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- puts ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD: puts ("AMD "); break;
- case FLASH_MAN_FUJ: puts ("FUJITSU "); break;
- case FLASH_MAN_BM: puts ("BRIGHT MICRO "); break;
- default: puts ("Unknown Vendor "); break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AM040: puts ("29F040/29LV040 (4 Mbit, uniform sectors)\n");
- break;
- case FLASH_AM400B: puts ("AM29LV400B (4 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM400T: puts ("AM29LV400T (4 Mbit, top boot sector)\n");
- break;
- case FLASH_AM800B: puts ("AM29LV800B (8 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM800T: puts ("AM29LV800T (8 Mbit, top boot sector)\n");
- break;
- case FLASH_AM160B: puts ("AM29LV160B (16 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM160T: puts ("AM29LV160T (16 Mbit, top boot sector)\n");
- break;
- case FLASH_AM320B: puts ("AM29LV320B (32 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM320T: puts ("AM29LV320T (32 Mbit, top boot sector)\n");
- break;
- case FLASH_AM033C: puts ("AM29LV033C (32 Mbit)\n");
- break;
- default: puts ("Unknown Chip Type\n");
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- puts (" Sector Start Addresses:");
-
- for (i=0; i<info->sector_count; ++i) {
- if ((i % 5) == 0) {
- puts ("\n ");
- }
-
- printf (" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " "
- );
- }
-
- puts ("\n");
-}
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-static ulong flash_get_size (vu_long *addr, flash_info_t *info)
-{
- short i;
-#if 0
- ulong base = (ulong)addr;
-#endif
- uchar value;
-
- /* Write auto select command: read Manufacturer ID */
-#if 0
- addr[0x0555] = 0x00AA00AA;
- addr[0x02AA] = 0x00550055;
- addr[0x0555] = 0x00900090;
-#else
- addr[0x0555] = 0xAAAAAAAA;
- addr[0x02AA] = 0x55555555;
- addr[0x0555] = 0x90909090;
-#endif
-
- value = addr[0];
-
- switch (value + (value << 16)) {
- case AMD_MANUFACT:
- info->flash_id = FLASH_MAN_AMD;
- break;
-
- case FUJ_MANUFACT:
- info->flash_id = FLASH_MAN_FUJ;
- break;
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- break;
- }
-
- value = addr[1]; /* device ID */
-
- switch ((unsigned long)value) {
- case AMD_ID_F040B:
- info->flash_id += FLASH_AM040;
- info->sector_count = 8;
- info->size = 0x00200000;
- break; /* => 2 MB */
-
- case AMD_ID_LV400T:
- info->flash_id += FLASH_AM400T;
- info->sector_count = 11;
- info->size = 0x00100000;
- break; /* => 1 MB */
-
- case AMD_ID_LV400B:
- info->flash_id += FLASH_AM400B;
- info->sector_count = 11;
- info->size = 0x00100000;
- break; /* => 1 MB */
-
- case AMD_ID_LV800T:
- info->flash_id += FLASH_AM800T;
- info->sector_count = 19;
- info->size = 0x00200000;
- break; /* => 2 MB */
-
- case AMD_ID_LV800B:
- info->flash_id += FLASH_AM800B;
- info->sector_count = 19;
- info->size = 0x00200000;
- break; /* => 2 MB */
-
- case AMD_ID_LV160T:
- info->flash_id += FLASH_AM160T;
- info->sector_count = 35;
- info->size = 0x00400000;
- break; /* => 4 MB */
-
- case AMD_ID_LV160B:
- info->flash_id += FLASH_AM160B;
- info->sector_count = 35;
- info->size = 0x00400000;
- break; /* => 4 MB */
-#if 0 /* enable when device IDs are available */
- case AMD_ID_LV320T:
- info->flash_id += FLASH_AM320T;
- info->sector_count = 67;
- info->size = 0x00800000;
- break; /* => 8 MB */
-
- case AMD_ID_LV320B:
- info->flash_id += FLASH_AM320B;
- info->sector_count = 67;
- info->size = 0x00800000;
- break; /* => 8 MB */
-#endif
- case AMD_ID_LV033C:
- info->flash_id += FLASH_AM033C;
- info->sector_count = 64;
- info->size = 0x01000000;
- break; /* => 16Mb */
- default:
- info->flash_id = FLASH_UNKNOWN;
- return (0); /* => no or unknown flash */
-
- }
-
-#if 0
- /* set up sector start address table */
- if (info->flash_id & FLASH_BTYPE) {
- /* set sector offsets for bottom boot block type */
- info->start[0] = base + 0x00000000;
- info->start[1] = base + 0x00008000;
- info->start[2] = base + 0x0000C000;
- info->start[3] = base + 0x00010000;
- for (i = 4; i < info->sector_count; i++) {
- info->start[i] = base + (i * 0x00020000) - 0x00060000;
- }
- } else {
- /* set sector offsets for top boot block type */
- i = info->sector_count - 1;
- info->start[i--] = base + info->size - 0x00008000;
- info->start[i--] = base + info->size - 0x0000C000;
- info->start[i--] = base + info->size - 0x00010000;
- for (; i >= 0; i--) {
- info->start[i] = base + i * 0x00020000;
- }
- }
-#else
- flash_get_offsets ((ulong)addr, &flash_info[0]);
-#endif
-
- /* check for protected sectors */
- for (i = 0; i < info->sector_count; i++) {
- /* read sector protection at sector address, (A7 .. A0) = 0x02 */
- /* D0 = 1 if protected */
- addr = (volatile unsigned long *)(info->start[i]);
-#if 1
- /* We don't know why it happens, but on ICU Board *
- * for AMD29033C flash we need to resend the command of *
- * reading flash protection for upper 8 Mb of flash */
- if ( i == 32 ) {
- addr[0x0555] = 0xAAAAAAAA;
- addr[0x02AA] = 0x55555555;
- addr[0x0555] = 0x90909090;
- }
-#endif
- info->protect[i] = addr[2] & 1;
- }
-
- /*
- * Prevent writes to uninitialized FLASH.
- */
- if (info->flash_id != FLASH_UNKNOWN) {
- addr = (volatile unsigned long *)info->start[0];
-#if 0
- *addr = 0x00F000F0; /* reset bank */
-#else
- *addr = 0xF0F0F0F0; /* reset bank */
-#endif
- }
-
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
- vu_long *addr = (vu_long*)(info->start[0]);
- int flag, prot, sect, l_sect;
- ulong start, now, last;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- puts ("- missing\n");
- } else {
- puts ("- no sectors to erase\n");
- }
- return 1;
- }
-
- if ((info->flash_id == FLASH_UNKNOWN) ||
- (info->flash_id > FLASH_AMD_COMP)) {
- puts ("Can't erase unknown flash type - aborted\n");
- return 1;
- }
-
- prot = 0;
- for (sect=s_first; sect<=s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- puts ("\n");
- }
-
- l_sect = -1;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
-#if 0
- addr[0x0555] = 0x00AA00AA;
- addr[0x02AA] = 0x00550055;
- addr[0x0555] = 0x00800080;
- addr[0x0555] = 0x00AA00AA;
- addr[0x02AA] = 0x00550055;
-#else
- addr[0x0555] = 0xAAAAAAAA;
- addr[0x02AA] = 0x55555555;
- addr[0x0555] = 0x80808080;
- addr[0x0555] = 0xAAAAAAAA;
- addr[0x02AA] = 0x55555555;
-#endif
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect<=s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr = (vu_long*)(info->start[sect]);
-#if 0
- addr[0] = 0x00300030;
-#else
- addr[0] = 0x30303030;
-#endif
- l_sect = sect;
- }
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- /*
- * We wait for the last triggered sector
- */
- if (l_sect < 0)
- goto DONE;
-
- start = get_timer (0);
- last = start;
- addr = (vu_long*)(info->start[l_sect]);
-#if 0
- while ((addr[0] & 0x00800080) != 0x00800080)
-#else
- while ((addr[0] & 0xFFFFFFFF) != 0xFFFFFFFF)
-#endif
- {
- if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- puts ("Timeout\n");
- return 1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc ('.');
- last = now;
- }
- }
-
-DONE:
- /* reset to read mode */
- addr = (volatile unsigned long *)info->start[0];
-#if 0
- addr[0] = 0x00F000F0; /* reset bank */
-#else
- addr[0] = 0xF0F0F0F0; /* reset bank */
-#endif
-
- puts (" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- ulong cp, wp, data;
- int i, l, rc;
-
- wp = (addr & ~3); /* get lower word aligned address */
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i=0, cp=wp; i<l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
- for (; i<4 && cnt>0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt==0 && i<4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= 4) {
- data = 0;
- for (i=0; i<4; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- cnt -= 4;
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i<4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- return (write_word(info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
- vu_long *addr = (vu_long*)(info->start[0]);
- ulong start;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*((vu_long *)dest) & data) != data) {
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
-#if 0
- addr[0x0555] = 0x00AA00AA;
- addr[0x02AA] = 0x00550055;
- addr[0x0555] = 0x00A000A0;
-#else
- addr[0x0555] = 0xAAAAAAAA;
- addr[0x02AA] = 0x55555555;
- addr[0x0555] = 0xA0A0A0A0;
-#endif
-
- *((vu_long *)dest) = data;
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* data polling for D7 */
- start = get_timer (0);
-#if 0
- while ((*((vu_long *)dest) & 0x00800080) != (data & 0x00800080))
-#else
- while ((*((vu_long *)dest) & 0x80808080) != (data & 0x80808080))
-#endif
- {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- return (1);
- }
- }
- return (0);
-}
-
-/*-----------------------------------------------------------------------
- */
diff --git a/board/icu862/icu862.c b/board/icu862/icu862.c
deleted file mode 100644
index 4c0e919..0000000
--- a/board/icu862/icu862.c
+++ /dev/null
@@ -1,199 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <config.h>
-#include <mpc8xx.h>
-
-/*
- * Memory Controller Using
- *
- * CS0 - Flash memory (0x40000000)
- * CS1 - SDRAM (0x00000000}
- * CS2 - S/UNI Ultra ATM155
- * CS3 - IDT 77106 ATM25
- * CS4 - DSP HPI
- * CS5 - E1/T1 Interface device
- * CS6 - PCMCIA device
- * CS7 - PCMCIA device
- */
-
-/* ------------------------------------------------------------------------- */
-
-#define _not_used_ 0xffffffff
-
-const uint sdram_table[] = {
- /* single read. (offset 0 in upm RAM) */
- 0x1f07fc04, 0xeeaefc04, 0x11adfc04, 0xefbbbc00,
- 0x1ff77c47,
-
- /* MRS initialization (offset 5) */
-
- 0x1ff77c34, 0xefeabc34, 0x1fb57c35,
-
- /* burst read. (offset 8 in upm RAM) */
- 0x1f07fc04, 0xeeaefc04, 0x10adfc04, 0xf0affc00,
- 0xf0affc00, 0xf1affc00, 0xefbbbc00, 0x1ff77c47,
- _not_used_, _not_used_, _not_used_, _not_used_,
- _not_used_, _not_used_, _not_used_, _not_used_,
-
- /* single write. (offset 18 in upm RAM) */
- 0x1f27fc04, 0xeeaebc00, 0x01b93c04, 0x1ff77c47,
- _not_used_, _not_used_, _not_used_, _not_used_,
-
- /* burst write. (offset 20 in upm RAM) */
- 0x1f07fc04, 0xeeaebc00, 0x10ad7c00, 0xf0affc00,
- 0xf0affc00, 0xe1bbbc04, 0x1ff77c47, _not_used_,
- _not_used_, _not_used_, _not_used_, _not_used_,
- _not_used_, _not_used_, _not_used_, _not_used_,
-
- /* refresh. (offset 30 in upm RAM) */
- 0x1ff5fc84, 0xfffffc04, 0xfffffc04, 0xfffffc04,
- 0xfffffc84, 0xfffffc07, _not_used_, _not_used_,
- _not_used_, _not_used_, _not_used_, _not_used_,
-
- /* exception. (offset 3c in upm RAM) */
- 0x7ffffc07, _not_used_, _not_used_, _not_used_
-};
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Check Board Identity:
- */
-
-int checkboard (void)
-{
- puts ("Board: ICU862 Board\n");
- return 0;
-}
-
-/* ------------------------------------------------------------------------- */
-
-static long int dram_size (long int, long int *, long int);
-
-/* ------------------------------------------------------------------------- */
-
-phys_size_t initdram (int board_type)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- long int size8, size9;
- long int size_b0 = 0;
- unsigned long reg;
-
- upmconfig (UPMA, (uint *) sdram_table,
- sizeof (sdram_table) / sizeof (uint));
-
- /*
- * Preliminary prescaler for refresh (depends on number of
- * banks): This value is selected for four cycles every 62.4 us
- * with two SDRAM banks or four cycles every 31.2 us with one
- * bank. It will be adjusted after memory sizing.
- */
- memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_8K;
-
- memctl->memc_mar = 0x00000088;
-
- /*
- * Map controller bank 1 to the SDRAM bank at
- * preliminary address - these have to be modified after the
- * SDRAM size has been determined.
- */
- memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
- memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
-
- memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
-
- udelay (200);
-
- /* perform SDRAM initializsation sequence */
-
- memctl->memc_mcr = 0x80002105; /* SDRAM bank 0 */
- udelay (200);
- memctl->memc_mcr = 0x80002230; /* SDRAM bank 0 - execute twice */
- udelay (200);
-
- memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
-
- udelay (1000);
-
- /*
- * Check Bank 0 Memory Size for re-configuration
- *
- * try 8 column mode
- */
- size8 = dram_size (CONFIG_SYS_MAMR_8COL, SDRAM_BASE1_PRELIM,
- SDRAM_MAX_SIZE);
-
- udelay (1000);
-
- /*
- * try 9 column mode
- */
- size9 = dram_size (CONFIG_SYS_MAMR_9COL, SDRAM_BASE1_PRELIM,
- SDRAM_MAX_SIZE);
-
- if (size8 < size9) { /* leave configuration at 9 columns */
- size_b0 = size9;
-/* debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20); */
- } else { /* back to 8 columns */
- size_b0 = size8;
- memctl->memc_mamr = CONFIG_SYS_MAMR_8COL;
- udelay (500);
-/* debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20); */
- }
-
- udelay (1000);
-
- /*
- * Adjust refresh rate depending on SDRAM type, both banks
- * For types > 128 MBit leave it at the current (fast) rate
- */
- if ((size_b0 < 0x02000000)) {
- /* reduce to 15.6 us (62.4 us / quad) */
- memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K;
- udelay (1000);
- }
-
- /*
- * Final mapping
- */
-
- memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
- memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
-
- /* adjust refresh rate depending on SDRAM type, one bank */
- reg = memctl->memc_mptpr;
- reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */
- memctl->memc_mptpr = reg;
-
- udelay (10000);
-
- return (size_b0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Check memory range for valid RAM. A simple memory test determines
- * the actually available RAM size between addresses `base' and
- * `base + maxsize'. Some (not all) hardware errors are detected:
- * - short between address lines
- * - short between data lines
- */
-
-static long int dram_size (long int mamr_value, long int *base,
- long int maxsize)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
-
- memctl->memc_mamr = mamr_value;
-
- return (get_ram_size(base, maxsize));
-}
diff --git a/board/icu862/pcmcia.c b/board/icu862/pcmcia.c
deleted file mode 100644
index dbe3c3c..0000000
--- a/board/icu862/pcmcia.c
+++ /dev/null
@@ -1,262 +0,0 @@
-#include <common.h>
-#include <mpc8xx.h>
-#include <pcmcia.h>
-
-#undef CONFIG_PCMCIA
-
-#if defined(CONFIG_CMD_PCMCIA)
-#define CONFIG_PCMCIA
-#endif
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
-#define CONFIG_PCMCIA
-#endif
-
-#ifdef CONFIG_PCMCIA
-
-#define PCMCIA_BOARD_MSG "ICU862"
-
-static void cfg_port_B (void)
-{
- volatile cpm8xx_t *cp;
- uint reg;
-
- cp = (cpm8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_cpm));
-
- /*
- * Configure Port B for TPS2205 PC-Card Power-Interface Switch
- *
- * Switch off all voltages, assert shutdown
- */
- reg = cp->cp_pbdat;
- reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC | /* VAVPP => Hi-Z */
- TPS2205_VCC3 | TPS2205_VCC5 | /* VAVCC => Hi-Z */
- TPS2205_SHDN); /* enable switch */
- cp->cp_pbdat = reg;
-
- cp->cp_pbpar &= ~(TPS2205_INPUTS | TPS2205_OUTPUTS);
-
- reg = cp->cp_pbdir & ~(TPS2205_INPUTS);
- cp->cp_pbdir = reg | TPS2205_OUTPUTS;
-
- debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n",
- cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat);
-}
-
-int pcmcia_hardware_enable(int slot)
-{
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, pipr, mask;
- int i;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- sysp = (sysconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_cpm));
-
- /* Configure Port B for TPS2205 PC-Card Power-Interface Switch */
- cfg_port_B ();
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- pipr = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- pipr,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
-
- reg = cp->cp_pbdat;
- if ((pipr & mask) == mask) {
- reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC | /* VAVPP => Hi-Z */
- TPS2205_VCC3); /* 3V off */
- reg &= ~(TPS2205_VCC5); /* 5V on */
- puts (" 5.0V card found: ");
- } else {
- reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC | /* VAVPP => Hi-Z */
- TPS2205_VCC5); /* 5V off */
- reg &= ~(TPS2205_VCC3); /* 3V on */
- puts (" 3.3V card found: ");
- }
-
- debug ("\nPB DAT: %08x -> 3.3V %s 5.0V %s VPP_PGM %s VPP_VCC %s\n",
- reg,
- (reg & TPS2205_VCC3) ? "off" : "on",
- (reg & TPS2205_VCC5) ? "off" : "on",
- (reg & TPS2205_VPP_PGM) ? "off" : "on",
- (reg & TPS2205_VPP_VCC) ? "off" : "on" );
-
- cp->cp_pbdat = reg;
-
- /* Wait 500 ms; use this to check for over-current */
- for (i=0; i<5000; ++i) {
- if ((cp->cp_pbdat & TPS2205_OC) == 0) {
- printf (" *** Overcurrent - Safety shutdown ***\n");
- cp->cp_pbdat &= ~(TPS2205_SHDN);
- return (1);
- }
- udelay (100);
- }
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if defined(CONFIG_CMD_PCMCIA)
-int pcmcia_hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CONFIG_SYS_IMMR;
- cp = (cpm8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_cpm));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
-
- /* Shut down */
- cp->cp_pbdat &= ~(TPS2205_SHDN);
-
- /* Configure PCMCIA General Control Register */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(10000);
-
- return (0);
-}
-#endif
-
-
-int pcmcia_voltage_set(int slot, int vcc, int vpp)
-{
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("voltage_set: "
- PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- cp = (cpm8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_cpm));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Configure Port C pins for
- * 5 Volts Enable and 3 Volts enable,
- * Turn all power pins to Hi-Z
- */
- debug ("PCMCIA power OFF\n");
- cfg_port_B (); /* Enables switch, but all in Hi-Z */
-
- reg = cp->cp_pbdat;
-
- switch(vcc) {
- case 0: break; /* Switch off */
- case 33: reg &= ~TPS2205_VCC3; break; /* Switch on 3.3V */
- case 50: reg &= ~TPS2205_VCC5; break; /* Switch on 5.0V */
- default: goto done;
- }
-
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
- cp->cp_pbdat = reg;
-
-#ifdef DEBUG
-{
- char *s;
-
- if ((reg & TPS2205_VCC3) == 0) {
- s = "at 3.3V";
- } else if ((reg & TPS2205_VCC5) == 0) {
- s = "at 5.0V";
- } else {
- s = "down";
- }
- printf ("PCMCIA powered %s\n", s);
-}
-#endif
-
-done:
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-
-#endif /* CONFIG_PCMCIA */
diff --git a/board/icu862/u-boot.lds b/board/icu862/u-boot.lds
deleted file mode 100644
index 00f63d2..0000000
--- a/board/icu862/u-boot.lds
+++ /dev/null
@@ -1,82 +0,0 @@
-/*
- * (C) Copyright 2001-2010
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .text :
- {
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FFF) & 0xFFFFF000;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
diff --git a/board/icu862/u-boot.lds.debug b/board/icu862/u-boot.lds.debug
deleted file mode 100644
index c7c6116..0000000
--- a/board/icu862/u-boot.lds.debug
+++ /dev/null
@@ -1,122 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-/* Do we need any of these for elf?
- __DYNAMIC = 0; */
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .interp : { *(.interp) }
- .hash : { *(.hash) }
- .dynsym : { *(.dynsym) }
- .dynstr : { *(.dynstr) }
- .rel.text : { *(.rel.text) }
- .rela.text : { *(.rela.text) }
- .rel.data : { *(.rel.data) }
- .rela.data : { *(.rela.data) }
- .rel.rodata : { *(.rel.rodata) }
- .rela.rodata : { *(.rela.rodata) }
- .rel.got : { *(.rel.got) }
- .rela.got : { *(.rela.got) }
- .rel.ctors : { *(.rel.ctors) }
- .rela.ctors : { *(.rela.ctors) }
- .rel.dtors : { *(.rel.dtors) }
- .rela.dtors : { *(.rela.dtors) }
- .rel.bss : { *(.rel.bss) }
- .rela.bss : { *(.rela.bss) }
- .rel.plt : { *(.rel.plt) }
- .rela.plt : { *(.rela.plt) }
- .init : { *(.init) }
- .plt : { *(.plt) }
- .text :
- {
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
-
- arch/powerpc/cpu/mpc8xx/start.o (.text)
- common/dlmalloc.o (.text)
- lib/vsprintf.o (.text)
- lib/crc32.o (.text)
- arch/powerpc/lib/extable.o (.text)
-
- . = env_offset;
- common/env_embedded.o(.text)
-
- *(.text)
- *(.got1)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(.rodata)
- *(.rodata1)
- *(.rodata.str1.4)
- *(.eh_frame)
- }
- .fini : { *(.fini) } =0
- .ctors : { *(.ctors) }
- .dtors : { *(.dtors) }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FFF) & 0xFFFFF000;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- *(.got)
- _GOT2_TABLE_ = .;
- *(.got2)
- _FIXUP_TABLE_ = .;
- *(.fixup)
- }
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data)
- *(.data1)
- *(.sdata)
- *(.sdata2)
- *(.dynamic)
- CONSTRUCTORS
- }
- _edata = .;
- PROVIDE (edata = .);
-
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(4096);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(4096);
- __init_end = .;
-
- __bss_start = .;
- .bss :
- {
- *(.sbss) *(.scommon)
- *(.dynbss)
- *(.bss)
- *(COMMON)
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
diff --git a/configs/ICU862_100MHz_defconfig b/configs/ICU862_100MHz_defconfig
deleted file mode 100644
index 72f0dfa..0000000
--- a/configs/ICU862_100MHz_defconfig
+++ /dev/null
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="100MHz"
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_ICU862=y
diff --git a/configs/ICU862_defconfig b/configs/ICU862_defconfig
deleted file mode 100644
index b58ea05..0000000
--- a/configs/ICU862_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_ICU862=y
diff --git a/include/commproc.h b/include/commproc.h
index 82a1a98..d481707 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -563,16 +563,6 @@ typedef struct scc_enet {
#endif /* CONFIG_HERMES */
-/*** ICU862 **********************************************************/
-
-#if defined(CONFIG_ICU862)
-
-#ifdef CONFIG_FEC_ENET
-#define FEC_ENET /* use FEC for EThernet */
-#endif /* CONFIG_FEC_ETHERNET */
-
-#endif /* CONFIG_ICU862 */
-
/*** IP860 **********************************************************/
#if defined(CONFIG_IP860)
diff --git a/include/configs/ICU862.h b/include/configs/ICU862.h
deleted file mode 100644
index 16af4bb..0000000
--- a/include/configs/ICU862.h
+++ /dev/null
@@ -1,443 +0,0 @@
-/*
- * (C) Copyright 2001-2005
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <mpc8xx_irq.h>
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_MPC860 1
-#define CONFIG_MPC860T 1
-#define CONFIG_ICU862 1
-#define CONFIG_MPC862 1
-
-#define CONFIG_SYS_TEXT_BASE 0x40F00000
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#undef CONFIG_8xx_CONS_SMC2
-#undef CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE 9600
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-
-#ifdef CONFIG_100MHz
-#define MPC8XX_FACT 24 /* Multiply by 24 */
-#define MPC8XX_XIN 4165000 /* 4.165 MHz in */
-#define CONFIG_8xx_GCLK_FREQ (MPC8XX_FACT * MPC8XX_XIN)
- /* define if cant' use get_gclk_freq */
-#else
-#if 1 /* for 50MHz version of processor */
-#define MPC8XX_FACT 12 /* Multiply by 12 */
-#define MPC8XX_XIN 4000000 /* 4 MHz in */
-#define CONFIG_8xx_GCLK_FREQ 48000000 /* define if cant use get_gclk_freq */
-#else /* for 80MHz version of processor */
-#define MPC8XX_FACT 20 /* Multiply by 20 */
-#define MPC8XX_XIN 4000000 /* 4 MHz in */
-#define CONFIG_8xx_GCLK_FREQ 80000000 /* define if cant use get_gclk_freq */
-#endif
-#endif
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "bootp;" \
- "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
- "bootm"
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#undef CONFIG_SCC1_ENET /* disable SCC1 ethernet */
-#define CONFIG_FEC_ENET 1 /* use FEC ethernet */
-#define CONFIG_MII 1
-#if 1
-#define CONFIG_SYS_DISCOVER_PHY 1
-#else
-#undef CONFIG_SYS_DISCOVER_PHY
-#endif
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL 0x00000020 /* PB 26 */
-#define PB_SDA 0x00000010 /* PB 27 */
-
-#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
-#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
-#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
- else immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
- else immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-
-#define CONFIG_SYS_EEPROM_X40430 /* Use a Xicor X40430 EEPROM */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16 bytes page write mode */
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x00100000
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xF0000000
-#define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024))
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#define CONFIG_SYS_FLASH_SIZE ((uint)(16 * 1024 * 1024)) /* max 16Mbyte */
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-
-#if 0
-#if defined(DEBUG)
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#else
-#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#endif
-#else
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#endif
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x00F40000
-
-#define CONFIG_ENV_SECT_SIZE 0x40000 /* Total Size of Environment sector */
-#define CONFIG_ENV_SIZE 0x4000 /* Used Size of Environment Sector */
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * set the PLL, the low-power modes and the reset control (15-29)
- */
-#define CONFIG_SYS_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
- PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#ifdef CONFIG_100MHz /* for 100 MHz, external bus is half CPU clock */
-#define SCCR_MASK 0
-#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_COM00 | SCCR_DFSYNC00 | \
- SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \
- SCCR_DFLCD000 |SCCR_DFALCD00 | SCCR_EBDF01)
-#else /* up to 50 MHz we use a 1:1 clock */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_COM00 | SCCR_DFSYNC00 | \
- SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \
- SCCR_DFLCD000 |SCCR_DFALCD00 )
-#endif /* CONFIG_100MHz */
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration Register 19-4
- *-----------------------------------------------------------------------
- */
-/* +0x09C4 => DRQP = 10 (IDMA requests have lowest priority) */
-#define CONFIG_SYS_RCCR 0x0020
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * PCMCIA Power Switch
- *
- * The ICU862 uses a TPS2205 PC-Card Power-Interface Switch to
- * control the voltages on the PCMCIA slot which is connected to Port B
- *-----------------------------------------------------------------------
- */
- /* Output pins */
-#define TPS2205_VCC5 0x00008000 /* PB.16: 5V Voltage Control */
-#define TPS2205_VCC3 0x00004000 /* PB.17: 3V Voltage Control */
-#define TPS2205_VPP_PGM 0x00002000 /* PB.18: PGM Voltage Control */
-#define TPS2205_VPP_VCC 0x00001000 /* PB.19: VPP Voltage Control */
-#define TPS2205_SHDN 0x00000200 /* PB.22: Shutdown */
-#define TPS2205_OUTPUTS ( TPS2205_VCC5 | TPS2205_VCC3 | \
- TPS2205_VPP_PGM | TPS2205_VPP_VCC | \
- TPS2205_SHDN)
-
- /* Input pins */
-#define TPS2205_OC 0x00000100 /* PB.23: Over-Current */
-#define TPS2205_INPUTS ( TPS2205_OC )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently. Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register. For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0 and OR0 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x0 /* FLASH bank #1 */
-
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-
-#define CONFIG_SYS_OR0_PRELIM 0xFF000954 /* Real values for the board */
-#define CONFIG_SYS_BR0_PRELIM 0x40000001 /* Real values for the board */
-
-/*
- * BR1 and OR1 (SDRAM)
- */
-#define SDRAM_BASE1_PRELIM 0x00000000 /* SDRAM bank */
-#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
-
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000800 /* BIH is not set */
-
-#define CONFIG_SYS_OR1_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM)
-#define CONFIG_SYS_BR1_PRELIM ((SDRAM_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V)
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#define CONFIG_SYS_MAMR 0x13a01114
-
-#ifdef CONFIG_MPC860T
-
-/* Interrupt level assignments.
-*/
-#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */
-
-#endif /* CONFIG_MPC860T */
-
-
-#endif /* __CONFIG_H */
diff --git a/include/pcmcia.h b/include/pcmcia.h
index 4b667f4..00065b2 100644
--- a/include/pcmcia.h
+++ b/include/pcmcia.h
@@ -29,8 +29,6 @@
# define CONFIG_PCMCIA_SLOT_A
#elif defined(CONFIG_LWMON) /* The LWMON use SLOT_B */
# define CONFIG_PCMCIA_SLOT_B
-#elif defined(CONFIG_ICU862) /* The ICU862 use SLOT_B */
-# define CONFIG_PCMCIA_SLOT_B
#elif defined(CONFIG_R360MPI) /* The R360MPI use SLOT_B */
# define CONFIG_PCMCIA_SLOT_B
#elif defined(CONFIG_ATC) /* The ATC use SLOT_A */
diff --git a/include/status_led.h b/include/status_led.h
index c1d2242..c5de894 100644
--- a/include/status_led.h
+++ b/include/status_led.h
@@ -114,25 +114,6 @@ void status_led_set (int led, int state);
# define STATUS_LED_GREEN 1
# define STATUS_LED_BOOT 2 /* IDE LED used for boot status */
-/***** ICU862 ********************************************************/
-#elif defined(CONFIG_ICU862)
-
-# define STATUS_LED_PAR im_ioport.iop_papar
-# define STATUS_LED_DIR im_ioport.iop_padir
-# define STATUS_LED_ODR im_ioport.iop_paodr
-# define STATUS_LED_DAT im_ioport.iop_padat
-
-# define STATUS_LED_BIT 0x4000 /* LED 0 is on PA.1 */
-# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-# define STATUS_LED_STATE STATUS_LED_BLINKING
-# define STATUS_LED_BIT1 0x1000 /* LED 1 is on PA.3 */
-# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ)
-# define STATUS_LED_STATE1 STATUS_LED_OFF
-
-# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
-
-# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
-
/***** Someone else defines these *************************************/
#elif defined(STATUS_LED_PAR)
--
2.1.1
More information about the U-Boot
mailing list