[U-Boot] [PATCH v2] powerpc/t4rdb: Add support of CPLD
Chunhe Lan
Chunhe.Lan at freescale.com
Mon Oct 20 10:03:15 CEST 2014
This support of CPLD includes
- Files and register definitions
- Command to switch alternate bank
- Command to switch default bank
Signed-off-by: Chunhe Lan <Chunhe.Lan at freescale.com>
---
board/freescale/t4rdb/Makefile | 1 +
board/freescale/t4rdb/cpld.c | 136 ++++++++++++++++++++++++++++++++++++++
board/freescale/t4rdb/cpld.h | 49 ++++++++++++++
board/freescale/t4rdb/law.c | 3 +
board/freescale/t4rdb/t4240rdb.c | 12 ++++
board/freescale/t4rdb/tlb.c | 5 ++
include/configs/T4240RDB.h | 23 +++++++
7 files changed, 229 insertions(+), 0 deletions(-)
create mode 100644 board/freescale/t4rdb/cpld.c
create mode 100644 board/freescale/t4rdb/cpld.h
diff --git a/board/freescale/t4rdb/Makefile b/board/freescale/t4rdb/Makefile
index f7f7fc0..3886e3d 100644
--- a/board/freescale/t4rdb/Makefile
+++ b/board/freescale/t4rdb/Makefile
@@ -5,6 +5,7 @@
#
obj-$(CONFIG_T4240RDB) += t4240rdb.o
+obj-y += cpld.o
obj-y += ddr.o
obj-y += eth.o
obj-$(CONFIG_PCI) += pci.o
diff --git a/board/freescale/t4rdb/cpld.c b/board/freescale/t4rdb/cpld.c
new file mode 100644
index 0000000..d5f3812
--- /dev/null
+++ b/board/freescale/t4rdb/cpld.c
@@ -0,0 +1,136 @@
+/**
+ * Copyright 2014 Freescale Semiconductor
+ *
+ * Author: Chunhe Lan <Chunhe.Lan at freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * This file provides support for the board-specific CPLD used on some Freescale
+ * reference boards.
+ *
+ * The following macros need to be defined:
+ *
+ * CONFIG_SYS_CPLD_BASE - The virtual address of the base of the
+ * CPLD register map
+ *
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/io.h>
+
+#include "cpld.h"
+
+u8 cpld_read(unsigned int reg)
+{
+ void *p = (void *)CONFIG_SYS_CPLD_BASE;
+
+ return in_8(p + reg);
+}
+
+void cpld_write(unsigned int reg, u8 value)
+{
+ void *p = (void *)CONFIG_SYS_CPLD_BASE;
+
+ out_8(p + reg, value);
+}
+
+/**
+ * Set the boot bank to the alternate bank
+ */
+void cpld_set_altbank(void)
+{
+ u8 val, curbank, altbank, override;
+
+ val = CPLD_READ(vbank);
+ curbank = val & CPLD_BANK_SEL_MASK;
+
+ switch (curbank) {
+ case CPLD_SELECT_BANK0:
+ altbank = CPLD_SELECT_BANK4;
+ CPLD_WRITE(vbank, altbank);
+ override = CPLD_READ(software_on);
+ CPLD_WRITE(software_on, override | CPLD_BANK_SEL_EN);
+ CPLD_WRITE(sys_reset, CPLD_SYSTEM_RESET);
+ break;
+ case CPLD_SELECT_BANK4:
+ altbank = CPLD_SELECT_BANK0;
+ CPLD_WRITE(vbank, altbank);
+ override = CPLD_READ(software_on);
+ CPLD_WRITE(software_on, override | CPLD_BANK_SEL_EN);
+ CPLD_WRITE(sys_reset, CPLD_SYSTEM_RESET);
+ break;
+ default:
+ printf("CPLD Altbank Fail: Invalid value!\n");
+ return;
+ }
+}
+
+/**
+ * Set the boot bank to the default bank
+ */
+void cpld_set_defbank(void)
+{
+ u8 val;
+
+ val = CPLD_DEFAULT_BANK;
+
+ CPLD_WRITE(global_reset, val);
+}
+
+#ifdef DEBUG
+static void cpld_dump_regs(void)
+{
+ printf("chip_id1 = 0x%02x\n", CPLD_READ(chip_id1));
+ printf("chip_id2 = 0x%02x\n", CPLD_READ(chip_id2));
+ printf("sw_maj_ver = 0x%02x\n", CPLD_READ(sw_maj_ver));
+ printf("sw_min_ver = 0x%02x\n", CPLD_READ(sw_min_ver));
+ printf("hw_ver = 0x%02x\n", CPLD_READ(hw_ver));
+ printf("software_on = 0x%02x\n", CPLD_READ(software_on));
+ printf("cfg_rcw_src = 0x%02x\n", CPLD_READ(cfg_rcw_src));
+ printf("res0 = 0x%02x\n", CPLD_READ(res0));
+ printf("vbank = 0x%02x\n", CPLD_READ(vbank));
+ printf("sw1_sysclk = 0x%02x\n", CPLD_READ(sw1_sysclk));
+ printf("sw2_status = 0x%02x\n", CPLD_READ(sw2_status));
+ printf("sw3_status = 0x%02x\n", CPLD_READ(sw3_status));
+ printf("sw4_status = 0x%02x\n", CPLD_READ(sw4_status));
+ printf("sys_reset = 0x%02x\n", CPLD_READ(sys_reset));
+ printf("global_reset = 0x%02x\n", CPLD_READ(global_reset));
+ printf("res1 = 0x%02x\n", CPLD_READ(res1));
+ putc('\n');
+}
+#endif
+
+#ifndef CONFIG_SPL_BUILD
+int do_cpld(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ int rc = 0;
+
+ if (argc <= 1)
+ return cmd_usage(cmdtp);
+
+ if (strcmp(argv[1], "reset") == 0) {
+ if (strcmp(argv[2], "altbank") == 0)
+ cpld_set_altbank();
+ else
+ cpld_set_defbank();
+#ifdef DEBUG
+ } else if (strcmp(argv[1], "dump") == 0) {
+ cpld_dump_regs();
+#endif
+ } else
+ rc = cmd_usage(cmdtp);
+
+ return rc;
+}
+
+U_BOOT_CMD(
+ cpld, CONFIG_SYS_MAXARGS, 1, do_cpld,
+ "Reset the board or alternate bank",
+ "reset - reset to default bank\n"
+ "cpld reset altbank - reset to alternate bank\n"
+#ifdef DEBUG
+ "cpld dump - display the CPLD registers\n"
+#endif
+ );
+#endif
diff --git a/board/freescale/t4rdb/cpld.h b/board/freescale/t4rdb/cpld.h
new file mode 100644
index 0000000..0180082
--- /dev/null
+++ b/board/freescale/t4rdb/cpld.h
@@ -0,0 +1,49 @@
+/**
+ * Copyright 2014 Freescale Semiconductor
+ *
+ * Author: Chunhe Lan <Chunhe.Lan at freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * This file provides support for the ngPIXIS, a board-specific FPGA used on
+ * some Freescale reference boards.
+ */
+
+/*
+ * CPLD register set. Feel free to add board-specific #ifdefs where necessary.
+ */
+struct cpld_data {
+ u8 chip_id1; /* 0x00 - CPLD Chip ID1 Register */
+ u8 chip_id2; /* 0x01 - CPLD Chip ID2 Register */
+ u8 sw_maj_ver; /* 0x02 - CPLD Code Major Version Register */
+ u8 sw_min_ver; /* 0x03 - CPLD Code Minor Version Register */
+ u8 hw_ver; /* 0x04 - PCBA Version Register */
+ u8 software_on; /* 0x05 - Override Physical Switch Enable Register */
+ u8 cfg_rcw_src; /* 0x06 - RCW Source Location Control Register */
+ u8 res0; /* 0x07 - not used */
+ u8 vbank; /* 0x08 - Flash Bank Selection Control Register */
+ u8 sw1_sysclk; /* 0x09 - SW1 Status Read Back Register */
+ u8 sw2_status; /* 0x0a - SW2 Status Read Back Register */
+ u8 sw3_status; /* 0x0b - SW3 Status Read Back Register */
+ u8 sw4_status; /* 0x0c - SW4 Status Read Back Register */
+ u8 sys_reset; /* 0x0d - Reset System With Reserving Registers Value*/
+ u8 global_reset;/* 0x0e - Reset System With Default Registers Value */
+ u8 res1; /* 0x0f - not used */
+};
+
+#define CPLD_BANK_SEL_MASK 0x07
+#define CPLD_BANK_SEL_EN 0x04
+#define CPLD_SYSTEM_RESET 0x01
+#define CPLD_SELECT_BANK0 0x00
+#define CPLD_SELECT_BANK4 0x04
+#define CPLD_DEFAULT_BANK 0x01
+
+/* Pointer to the CPLD register set */
+
+u8 cpld_read(unsigned int reg);
+void cpld_write(unsigned int reg, u8 value);
+
+#define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg))
+#define CPLD_WRITE(reg, value) \
+ cpld_write(offsetof(struct cpld_data, reg), value)
+
diff --git a/board/freescale/t4rdb/law.c b/board/freescale/t4rdb/law.c
index 1f58768..39818fc 100644
--- a/board/freescale/t4rdb/law.c
+++ b/board/freescale/t4rdb/law.c
@@ -16,6 +16,9 @@ struct law_entry law_table[] = {
#ifdef CONFIG_SYS_QMAN_MEM_PHYS
SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
#endif
+#ifdef CONFIG_SYS_CPLD_BASE_PHYS
+ SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
+#endif
#ifdef CONFIG_SYS_DCSRBAR_PHYS
/* Limit DCSR to 32M to access NPC Trace Buffer */
SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
diff --git a/board/freescale/t4rdb/t4240rdb.c b/board/freescale/t4rdb/t4240rdb.c
index 5448c86..027861f 100644
--- a/board/freescale/t4rdb/t4240rdb.c
+++ b/board/freescale/t4rdb/t4240rdb.c
@@ -20,14 +20,26 @@
#include <fm_eth.h>
#include "t4rdb.h"
+#include "cpld.h"
DECLARE_GLOBAL_DATA_PTR;
int checkboard(void)
{
struct cpu_type *cpu = gd->arch.cpu;
+ u8 sw;
printf("Board: %sRDB, ", cpu->name);
+ printf("Board rev: 0x%02x CPLD ver: 0x%02x%02x, ",
+ CPLD_READ(hw_ver), CPLD_READ(sw_maj_ver), CPLD_READ(sw_min_ver));
+
+ sw = CPLD_READ(vbank);
+ sw = sw & CPLD_BANK_SEL_MASK;
+
+ if (sw <= 7)
+ printf("vBank: %d\n", sw);
+ else
+ printf("Unsupported Bank=%x\n", sw);
puts("SERDES Reference Clocks:\n");
printf(" SERDES1=100MHz SERDES2=156.25MHz\n"
diff --git a/board/freescale/t4rdb/tlb.c b/board/freescale/t4rdb/tlb.c
index 4b50bcd..474301e 100644
--- a/board/freescale/t4rdb/tlb.c
+++ b/board/freescale/t4rdb/tlb.c
@@ -106,6 +106,11 @@ struct fsl_e_tlb_entry tlb_table[] = {
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 16, BOOKE_PAGESZ_64K, 1),
#endif
+#ifdef CONFIG_SYS_CPLD_BASE
+ SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS,
+ MAS3_SW|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 17, BOOKE_PAGESZ_4K, 1),
+#endif
};
int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/include/configs/T4240RDB.h b/include/configs/T4240RDB.h
index 183255d..7b7fce5 100644
--- a/include/configs/T4240RDB.h
+++ b/include/configs/T4240RDB.h
@@ -513,6 +513,29 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
+/* CPLD on IFC */
+#define CONFIG_SYS_CPLD_BASE 0xffdf0000
+#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
+#define CONFIG_SYS_CSPR3_EXT (0xf)
+#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_GPCM \
+ | CSPR_V)
+
+#define CONFIG_SYS_AMASK3 IFC_AMASK(4*1024)
+#define CONFIG_SYS_CSOR3 0x0
+
+/* CPLD Timing parameters for IFC CS3 */
+#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
+ FTIM0_GPCM_TEADC(0x0e) | \
+ FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \
+ FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
+ FTIM2_GPCM_TCH(0x8) | \
+ FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS3_FTIM3 0x0
+
#if defined(CONFIG_RAMBOOT_PBL)
#define CONFIG_SYS_RAMBOOT
#endif
--
1.7.6.5
More information about the U-Boot
mailing list