On 22/10/2014 01:14, Fabio Estevam wrote:
> From: Fabio Estevam <fabio.estevam at freescale.com>
>
> Add support for the 4.3'' Seiko WVGA parallel display.
>
> In order to direct the splash screen to the Seiko display:
>
> => setenv panel SEIKO-WVGA
> => save
> => reset
>
> Signed-off-by: Fabio Estevam <fabio.estevam at freescale.com>
> ---
> board/freescale/mx6sabresd/mx6sabresd.c | 61 +++++++++++++++++++++++++++++++++
> 1 file changed, 61 insertions(+)
>
> diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
> index 81dcd6e..3d81fff 100644
> --- a/board/freescale/mx6sabresd/mx6sabresd.c
> +++ b/board/freescale/mx6sabresd/mx6sabresd.c
> @@ -51,6 +51,8 @@ DECLARE_GLOBAL_DATA_PTR;
>
> #define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
>
> +#define DISP0_PWR_EN IMX_GPIO_NR(1, 21)
> +
> int dram_init(void)
> {
> gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
> @@ -141,6 +143,45 @@ iomux_v3_cfg_t const ecspi1_pads[] = {
> MX6_PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
> };
>
> +static iomux_v3_cfg_t const rgb_pads[] = {
> + MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DI0_PIN4__IPU1_DI0_PIN04 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 | MUX_PAD_CTRL(NO_PAD_CTRL),
> + MX6_PAD_SD1_DAT3__GPIO1_IO21 | MUX_PAD_CTRL(NO_PAD_CTRL),
> +};
> +
> +static void enable_rgb(struct display_info_t const *dev)
> +{
> + imx_iomux_v3_setup_multiple_pads(rgb_pads, ARRAY_SIZE(rgb_pads));
> + gpio_direction_output(DISP0_PWR_EN, 1);
> +}
> +
> static struct i2c_pads_info i2c_pad_info1 = {
> .scl = {
> .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
> @@ -357,6 +398,26 @@ struct display_info_t const displays[] = {{
> .vsync_len = 10,
> .sync = FB_SYNC_EXT,
> .vmode = FB_VMODE_NONINTERLACED
> +} }, {
> + .bus = 0,
> + .addr = 0,
> + .pixfmt = IPU_PIX_FMT_RGB24,
> + .detect = NULL,
> + .enable = enable_rgb,
> + .mode = {
> + .name = "SEIKO-WVGA",
> + .refresh = 60,
> + .xres = 800,
> + .yres = 480,
> + .pixclock = 29850,
> + .left_margin = 89,
> + .right_margin = 164,
> + .upper_margin = 23,
> + .lower_margin = 10,
> + .hsync_len = 10,
> + .vsync_len = 10,
> + .sync = 0,
> + .vmode = FB_VMODE_NONINTERLACED
> } } };
> size_t display_count = ARRAY_SIZE(displays);
>
>
Acked-by: Stefano Babic <sbabic at denx.de>
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================