[U-Boot] [PATCH 2/4] imx: mx6slevk: Add PMIC Pfuze support

Ye.Li B37916 at freescale.com
Wed Sep 10 11:08:15 CEST 2014


Initialize the Pfuze on I2C1 at board late init. The mx6slevk board
has Pfuze100 or Pfuze200, print the chip type by parsing the ID.

Signed-off-by: Ye.Li <B37916 at freescale.com>
---
 board/freescale/mx6slevk/mx6slevk.c |   57 +++++++++++++++++++++++++++++++++++
 include/configs/mx6slevk.h          |    7 ++++
 2 files changed, 64 insertions(+), 0 deletions(-)

diff --git a/board/freescale/mx6slevk/mx6slevk.c b/board/freescale/mx6slevk/mx6slevk.c
index fedd5c3..8b6a79c 100644
--- a/board/freescale/mx6slevk/mx6slevk.c
+++ b/board/freescale/mx6slevk/mx6slevk.c
@@ -21,6 +21,8 @@
 #include <mmc.h>
 #include <netdev.h>
 #include <i2c.h>
+#include <power/pmic.h>
+#include <power/pfuze100_pmic.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -48,6 +50,8 @@ DECLARE_GLOBAL_DATA_PTR;
 
 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
 
+#define I2C_PMIC	0
+
 /* I2C1 for PMIC */
 struct i2c_pads_info i2c_pad_info0 = {
 	.sda = {
@@ -191,6 +195,59 @@ int board_init(void)
 	return 0;
 }
 
+static int pfuze_init(void)
+{
+	struct pmic *p;
+	int ret;
+	unsigned int reg;
+
+	ret = power_pfuze100_init(I2C_PMIC);
+	if (ret)
+		return ret;
+
+	p = pmic_get("PFUZE100");
+	ret = pmic_probe(p);
+	if (ret)
+		return ret;
+
+	pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
+	printf("PMIC:  PFUZE%s ID=0x%02x\n",
+		((reg & 0xf) == 0) ? "100" : "200", reg);
+
+	/* Set SW1AB stanby volage to 0.975V */
+	pmic_reg_read(p, PFUZE100_SW1ABSTBY, &reg);
+	reg &= ~0x3f;
+	reg |= 0x1b;
+	pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg);
+
+	/* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
+	pmic_reg_read(p, PUZE_100_SW1ABCONF, &reg);
+	reg &= ~0xc0;
+	reg |= 0x40;
+	pmic_reg_write(p, PUZE_100_SW1ABCONF, reg);
+
+	/* Set SW1C standby voltage to 0.975V */
+	pmic_reg_read(p, PFUZE100_SW1CSTBY, &reg);
+	reg &= ~0x3f;
+	reg |= 0x1b;
+	pmic_reg_write(p, PFUZE100_SW1CSTBY, reg);
+
+	/* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
+	pmic_reg_read(p, PFUZE100_SW1CCONF, &reg);
+	reg &= ~0xc0;
+	reg |= 0x40;
+	pmic_reg_write(p, PFUZE100_SW1CCONF, reg);
+
+	return 0;
+}
+
+int board_late_init(void)
+{
+	pfuze_init();
+
+	return 0;
+}
+
 u32 get_board_rev(void)
 {
 	return get_cpu_rev();
diff --git a/include/configs/mx6slevk.h b/include/configs/mx6slevk.h
index bf5066f..09d0896 100644
--- a/include/configs/mx6slevk.h
+++ b/include/configs/mx6slevk.h
@@ -30,6 +30,7 @@
 #define CONFIG_SYS_MALLOC_LEN		(3 * SZ_1M)
 
 #define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
 #define CONFIG_MXC_GPIO
 
 #define CONFIG_MXC_UART
@@ -66,6 +67,12 @@
 #define CONFIG_SYS_I2C_MXC
 #define CONFIG_SYS_I2C_SPEED		  100000
 
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE100
+#define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
+
 /* allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_CONS_INDEX		1
-- 
1.7.4.1



More information about the U-Boot mailing list