[U-Boot] [PATCH 4/4] imx: mx6: Set Pfuze mode to decrease power number for DSM

[Ye.Li]

Set all switches APS mode in normal and PFM mode in standby. So when
mx6 entering DSM mode, the power number can be decreased. There is
no impact for mx6 in run mode.

Changes for boards:
-mx6 sabreauto
-mx6 sabresd
-mx6slevk
-mx6sxsabresd

Signed-off-by: Ye.Li <B37916 at freescale.com>
---
 board/freescale/mx6qsabreauto/mx6qsabreauto.c |   36 +++++++++++++++++++++++++
 board/freescale/mx6sabresd/mx6sabresd.c       |   36 +++++++++++++++++++++++++
 board/freescale/mx6slevk/mx6slevk.c           |   36 +++++++++++++++++++++++++
 board/freescale/mx6sxsabresd/mx6sxsabresd.c   |   36 +++++++++++++++++++++++++
 4 files changed, 144 insertions(+), 0 deletions(-)

diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
index 76b024b..9e79915 100644
--- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c
+++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
@@ -263,6 +263,37 @@ int board_init(void)
 	return 0;
 }
 
+/* set all switches APS in normal and PFM mode in standby */
+static int pfuze_setup_mode(struct pmic *p, int chip)
+{
+	unsigned char offset, i, switch_num, value;
+
+	if (!chip) {
+		/* pfuze100 */
+		switch_num = 6;
+		offset = 0x31;
+	} else {
+		/* pfuze200 */
+		switch_num = 4;
+		offset = 0x38;
+	}
+
+	value = 0xc;
+	if (pmic_reg_write(p, 0x23, value)) {
+		printf("Set SW1AB mode error!\n");
+		return -1;
+	}
+
+	for (i = 0; i < switch_num - 1; i++) {
+		if (pmic_reg_write(p, offset + i * 7, value)) {
+			printf("Set switch%x mode error!\n", offset);
+			return -1;
+		}
+	}
+
+	return 0;
+}
+
 static int pfuze_init(void)
 {
 	struct pmic *p;
@@ -281,6 +312,11 @@ static int pfuze_init(void)
 	pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
 	printf("PMIC:  PFUZE100 ID=0x%02x\n", reg);
 
+	if (pfuze_setup_mode(p, (reg & 0xf))) {
+		printf("setup pfuze mode error!\n");
+		return -1;
+	}
+
 	/* Set SW1AB stanby volage to 0.975V */
 	pmic_reg_read(p, PFUZE100_SW1ABSTBY, &reg);
 	reg &= ~0x3f;
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 72d6562..810fe13 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -456,6 +456,37 @@ int board_init(void)
 	return 0;
 }
 
+/* set all switches APS in normal and PFM mode in standby */
+static int pfuze_setup_mode(struct pmic *p, int chip)
+{
+	unsigned char offset, i, switch_num, value;
+
+	if (!chip) {
+		/* pfuze100 */
+		switch_num = 6;
+		offset = 0x31;
+	} else {
+		/* pfuze200 */
+		switch_num = 4;
+		offset = 0x38;
+	}
+
+	value = 0xc;
+	if (pmic_reg_write(p, 0x23, value)) {
+		printf("Set SW1AB mode error!\n");
+		return -1;
+	}
+
+	for (i = 0; i < switch_num - 1; i++) {
+		if (pmic_reg_write(p, offset + i * 7, value)) {
+			printf("Set switch%x mode error!\n", offset);
+			return -1;
+		}
+	}
+
+	return 0;
+}
+
 static int pfuze_init(void)
 {
 	struct pmic *p;
@@ -475,6 +506,11 @@ static int pfuze_init(void)
 	printf("PMIC:  PFUZE%s ID=0x%02x\n",
 		((reg & 0xf) == 0) ? "100" : "200", reg);
 
+	if (pfuze_setup_mode(p, (reg & 0xf))) {
+		printf("setup pfuze mode error!\n");
+		return -1;
+	}
+
 	/* Increase VGEN3 from 2.5 to 2.8V */
 	pmic_reg_read(p, PFUZE100_VGEN3VOL, &reg);
 	reg &= ~0xf;
diff --git a/board/freescale/mx6slevk/mx6slevk.c b/board/freescale/mx6slevk/mx6slevk.c
index 8b6a79c..fe5e37d 100644
--- a/board/freescale/mx6slevk/mx6slevk.c
+++ b/board/freescale/mx6slevk/mx6slevk.c
@@ -195,6 +195,37 @@ int board_init(void)
 	return 0;
 }
 
+/* set all switches APS in normal and PFM mode in standby */
+static int pfuze_setup_mode(struct pmic *p, int chip)
+{
+	unsigned char offset, i, switch_num, value;
+
+	if (!chip) {
+		/* pfuze100 */
+		switch_num = 6;
+		offset = 0x31;
+	} else {
+		/* pfuze200 */
+		switch_num = 4;
+		offset = 0x38;
+	}
+
+	value = 0xc;
+	if (pmic_reg_write(p, 0x23, value)) {
+		printf("Set SW1AB mode error!\n");
+		return -1;
+	}
+
+	for (i = 0; i < switch_num - 1; i++) {
+		if (pmic_reg_write(p, offset + i * 7, value)) {
+			printf("Set switch%x mode error!\n", offset);
+			return -1;
+		}
+	}
+
+	return 0;
+}
+
 static int pfuze_init(void)
 {
 	struct pmic *p;
@@ -214,6 +245,11 @@ static int pfuze_init(void)
 	printf("PMIC:  PFUZE%s ID=0x%02x\n",
 		((reg & 0xf) == 0) ? "100" : "200", reg);
 
+	if (pfuze_setup_mode(p, (reg & 0xf))) {
+		printf("setup pfuze mode error!\n");
+		return -1;
+	}
+
 	/* Set SW1AB stanby volage to 0.975V */
 	pmic_reg_read(p, PFUZE100_SW1ABSTBY, &reg);
 	reg &= ~0x3f;
diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
index 80d2d99..d6a33cd 100644
--- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c
+++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
@@ -170,6 +170,37 @@ struct i2c_pads_info i2c_pad_info1 = {
 	},
 };
 
+/* set all switches APS in normal and PFM mode in standby */
+static int pfuze_setup_mode(struct pmic *p, int chip)
+{
+	unsigned char offset, i, switch_num, value;
+
+	if (!chip) {
+		/* pfuze100 */
+		switch_num = 6;
+		offset = 0x31;
+	} else {
+		/* pfuze200 */
+		switch_num = 4;
+		offset = 0x38;
+	}
+
+	value = 0xc;
+	if (pmic_reg_write(p, 0x23, value)) {
+		printf("Set SW1AB mode error!\n");
+		return -1;
+	}
+
+	for (i = 0; i < switch_num - 1; i++) {
+		if (pmic_reg_write(p, offset + i * 7, value)) {
+			printf("Set switch%x mode error!\n", offset);
+			return -1;
+		}
+	}
+
+	return 0;
+}
+
 static int pfuze_init(void)
 {
 	struct pmic *p;
@@ -188,6 +219,11 @@ static int pfuze_init(void)
 	pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
 	printf("PMIC:  PFUZE100 ID=0x%02x\n", reg);
 
+	if (pfuze_setup_mode(p, (reg & 0xf))) {
+		printf("setup pfuze mode error!\n");
+		return -1;
+	}
+
 	/* Set SW1AB standby voltage to 0.975V */
 	pmic_reg_read(p, PFUZE100_SW1ABSTBY, &reg);
 	reg &= ~0x3f;
-- 
1.7.4.1