[U-Boot] [PATCH 1/5] am33xx: Update DT files, add am335x_gp_evm_config target
Tom Rini
trini at konsulko.com
Sat Aug 1 01:55:08 CEST 2015
- Re-sync DT files for am33xx with Linux Kernel v4.1
- Include DT file now for the "AM335x GP EVM" and build target for it,
via device tree and DM.
- We only need to provide platform data for UART when OF_CONTROL isn't
also enabled really. We can just push GPIO to coming from DT
Signed-off-by: Tom Rini <trini at konsulko.com>
---
arch/arm/cpu/armv7/am33xx/board.c | 36 +-
arch/arm/dts/Makefile | 2 +-
arch/arm/dts/am335x-bone-common.dtsi | 410 +++++++++++-------
arch/arm/dts/am335x-bone.dts | 29 ++
arch/arm/dts/am335x-boneblack.dts | 72 ++++
arch/arm/dts/am335x-evm.dts | 765 ++++++++++++++++++++++++++++++++++
arch/arm/dts/am33xx-clocks.dtsi | 646 ++++++++++++++++++++++++++++
arch/arm/dts/am33xx.dtsi | 297 +++++++++++--
arch/arm/dts/tps65910.dtsi | 91 ++++
configs/am335x_gp_evm_defconfig | 14 +
10 files changed, 2156 insertions(+), 206 deletions(-)
create mode 100644 arch/arm/dts/am335x-bone.dts
create mode 100644 arch/arm/dts/am335x-evm.dts
create mode 100644 arch/arm/dts/am33xx-clocks.dtsi
create mode 100644 arch/arm/dts/tps65910.dtsi
create mode 100644 configs/am335x_gp_evm_defconfig
diff --git a/arch/arm/cpu/armv7/am33xx/board.c b/arch/arm/cpu/armv7/am33xx/board.c
index 67bef23..81492a5 100644
--- a/arch/arm/cpu/armv7/am33xx/board.c
+++ b/arch/arm/cpu/armv7/am33xx/board.c
@@ -38,45 +38,22 @@
DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_DM_GPIO
-static const struct omap_gpio_platdata am33xx_gpio[] = {
- { 0, AM33XX_GPIO0_BASE, METHOD_GPIO_24XX },
- { 1, AM33XX_GPIO1_BASE, METHOD_GPIO_24XX },
- { 2, AM33XX_GPIO2_BASE, METHOD_GPIO_24XX },
- { 3, AM33XX_GPIO3_BASE, METHOD_GPIO_24XX },
-#ifdef CONFIG_AM43XX
- { 4, AM33XX_GPIO4_BASE, METHOD_GPIO_24XX },
- { 5, AM33XX_GPIO5_BASE, METHOD_GPIO_24XX },
-#endif
-};
-
-U_BOOT_DEVICES(am33xx_gpios) = {
- { "gpio_omap", &am33xx_gpio[0] },
- { "gpio_omap", &am33xx_gpio[1] },
- { "gpio_omap", &am33xx_gpio[2] },
- { "gpio_omap", &am33xx_gpio[3] },
-#ifdef CONFIG_AM43XX
- { "gpio_omap", &am33xx_gpio[4] },
- { "gpio_omap", &am33xx_gpio[5] },
-#endif
-};
-
-# ifndef CONFIG_OF_CONTROL
+#if defined(CONFIG_DM_SERIAL) && !defined(CONFIG_OF_CONTROL)
/*
* TODO(sjg at chromium.org): When we can move SPL serial to DM, we can remove
* the CONFIGs. At the same time, we should move this to the board files.
*/
static const struct ns16550_platdata am33xx_serial[] = {
{ CONFIG_SYS_NS16550_COM1, 2, CONFIG_SYS_NS16550_CLK },
-# ifdef CONFIG_SYS_NS16550_COM2
+# ifdef CONFIG_SYS_NS16550_COM2
{ CONFIG_SYS_NS16550_COM2, 2, CONFIG_SYS_NS16550_CLK },
-# ifdef CONFIG_SYS_NS16550_COM3
+# ifdef CONFIG_SYS_NS16550_COM3
{ CONFIG_SYS_NS16550_COM3, 2, CONFIG_SYS_NS16550_CLK },
{ CONFIG_SYS_NS16550_COM4, 2, CONFIG_SYS_NS16550_CLK },
{ CONFIG_SYS_NS16550_COM5, 2, CONFIG_SYS_NS16550_CLK },
{ CONFIG_SYS_NS16550_COM6, 2, CONFIG_SYS_NS16550_CLK },
-# endif
# endif
+# endif
};
U_BOOT_DEVICES(am33xx_uarts) = {
@@ -91,10 +68,10 @@ U_BOOT_DEVICES(am33xx_uarts) = {
# endif
# endif
};
-# endif
+#endif
-#else
+#ifndef CONFIG_DM_GPIO
static const struct gpio_bank gpio_bank_am33xx[] = {
{ (void *)AM33XX_GPIO0_BASE, METHOD_GPIO_24XX },
{ (void *)AM33XX_GPIO1_BASE, METHOD_GPIO_24XX },
@@ -107,7 +84,6 @@ static const struct gpio_bank gpio_bank_am33xx[] = {
};
const struct gpio_bank *const omap_gpio_bank = gpio_bank_am33xx;
-
#endif
#if defined(CONFIG_OMAP_HSMMC) && !defined(CONFIG_SPL_BUILD)
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index ba63553..43b1616 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -49,7 +49,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
zynq-zc770-xm011.dtb \
zynq-zc770-xm012.dtb \
zynq-zc770-xm013.dtb
-dtb-$(CONFIG_AM33XX) += am335x-boneblack.dtb
+dtb-$(CONFIG_AM33XX) += am335x-boneblack.dtb am335x-evm.dtb
dtb-$(CONFIG_ARCH_SOCFPGA) += \
socfpga_arria5_socdk.dtb \
diff --git a/arch/arm/dts/am335x-bone-common.dtsi b/arch/arm/dts/am335x-bone-common.dtsi
index e70b4d1..fec7834 100644
--- a/arch/arm/dts/am335x-bone-common.dtsi
+++ b/arch/arm/dts/am335x-bone-common.dtsi
@@ -7,13 +7,6 @@
*/
/ {
- model = "TI AM335x BeagleBone";
- compatible = "ti,am335x-bone", "ti,am33xx";
-
- chosen {
- stdout-path = &uart0;
- };
-
cpus {
cpu at 0 {
cpu0-supply = <&dcdc2_reg>;
@@ -25,184 +18,299 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- am33xx_pinmux: pinmux at 44e10800 {
+ leds {
pinctrl-names = "default";
- pinctrl-0 = <&clkout2_pin>;
-
- user_leds_s0: user_leds_s0 {
- pinctrl-single,pins = <
- 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
- 0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */
- 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */
- 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */
- >;
- };
+ pinctrl-0 = <&user_leds_s0>;
- i2c0_pins: pinmux_i2c0_pins {
- pinctrl-single,pins = <
- 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
- 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
- >;
- };
+ compatible = "gpio-leds";
- uart0_pins: pinmux_uart0_pins {
- pinctrl-single,pins = <
- 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
- 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
- >;
+ led at 2 {
+ label = "beaglebone:green:heartbeat";
+ gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
};
- clkout2_pin: pinmux_clkout2_pin {
- pinctrl-single,pins = <
- 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
- >;
+ led at 3 {
+ label = "beaglebone:green:mmc0";
+ gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ default-state = "off";
};
- cpsw_default: cpsw_default {
- pinctrl-single,pins = <
- /* Slave 1 */
- 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */
- 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */
- 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */
- 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */
- 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */
- 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */
- 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */
- 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */
- 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */
- 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */
- 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */
- 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */
- 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */
- >;
+ led at 4 {
+ label = "beaglebone:green:usr2";
+ gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "cpu0";
+ default-state = "off";
};
- cpsw_sleep: cpsw_sleep {
- pinctrl-single,pins = <
- /* Slave 1 reset value */
- 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
+ led at 5 {
+ label = "beaglebone:green:usr3";
+ gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc1";
+ default-state = "off";
};
+ };
- davinci_mdio_default: davinci_mdio_default {
- pinctrl-single,pins = <
- /* MDIO */
- 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
- 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
- >;
- };
+ vmmcsd_fixed: fixedregulator at 0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmcsd_fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
- davinci_mdio_sleep: davinci_mdio_sleep {
- pinctrl-single,pins = <
- /* MDIO reset value */
- 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
- 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
- >;
- };
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&clkout2_pin>;
+
+ user_leds_s0: user_leds_s0 {
+ pinctrl-single,pins = <
+ 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
+ 0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */
+ 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */
+ 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */
+ >;
};
- ocp {
- uart0: serial at 44e09000 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins>;
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
- status = "okay";
- };
+ i2c2_pins: pinmux_i2c2_pins {
+ pinctrl-single,pins = <
+ 0x178 (PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_ctsn.i2c2_sda */
+ 0x17c (PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_rtsn.i2c2_scl */
+ >;
+ };
- musb: usb at 47400000 {
- status = "okay";
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
- control at 44e10000 {
- status = "okay";
- };
+ clkout2_pin: pinmux_clkout2_pin {
+ pinctrl-single,pins = <
+ 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
+ >;
+ };
- usb-phy at 47401300 {
- status = "okay";
- };
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Slave 1 */
+ 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */
+ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */
+ 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */
+ 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */
+ 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */
+ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */
+ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */
+ 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */
+ 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */
+ 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */
+ 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */
+ 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */
+ 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */
+ >;
+ };
- usb-phy at 47401b00 {
- status = "okay";
- };
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ /* Slave 1 reset value */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
- usb at 47401000 {
- status = "okay";
- };
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
- usb at 47401800 {
- status = "okay";
- dr_mode = "host";
- };
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
- dma-controller at 07402000 {
- status = "okay";
- };
- };
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ 0x160 (PIN_INPUT | MUX_MODE7) /* GPIO0_6 */
+ >;
+ };
+
+ emmc_pins: pinmux_emmc_pins {
+ pinctrl-single,pins = <
+ 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+ 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
+ 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+ 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+ 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+ 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
+ 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
+ 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
+ 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
+ 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
+ >;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
- i2c0: i2c at 44e0b000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
+ status = "okay";
+};
- status = "okay";
- clock-frequency = <400000>;
+&usb {
+ status = "okay";
+};
- tps: tps at 24 {
- reg = <0x24>;
- };
+&usb_ctrl_mod {
+ status = "okay";
+};
+&usb0_phy {
+ status = "okay";
+};
+
+&usb1_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "peripheral";
+};
+
+&usb1 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&cppi41dma {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: tps at 24 {
+ reg = <0x24>;
+ };
+
+ baseboard_eeprom: baseboard_eeprom at 50 {
+ compatible = "at,24c256";
+ reg = <0x50>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ baseboard_data: baseboard_data at 0 {
+ reg = <0 0x100>;
};
};
+};
- leds {
- pinctrl-names = "default";
- pinctrl-0 = <&user_leds_s0>;
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
- compatible = "gpio-leds";
+ status = "okay";
+ clock-frequency = <100000>;
- led at 2 {
- label = "beaglebone:green:heartbeat";
- gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- default-state = "off";
+ cape_eeprom0: cape_eeprom0 at 54 {
+ compatible = "at,24c256";
+ reg = <0x54>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cape0_data: cape_data at 0 {
+ reg = <0 0x100>;
};
+ };
- led at 3 {
- label = "beaglebone:green:mmc0";
- gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc0";
- default-state = "off";
+ cape_eeprom1: cape_eeprom1 at 55 {
+ compatible = "at,24c256";
+ reg = <0x55>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cape1_data: cape_data at 0 {
+ reg = <0 0x100>;
};
+ };
- led at 4 {
- label = "beaglebone:green:usr2";
- gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
- default-state = "off";
+ cape_eeprom2: cape_eeprom2 at 56 {
+ compatible = "at,24c256";
+ reg = <0x56>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cape2_data: cape_data at 0 {
+ reg = <0 0x100>;
};
+ };
- led at 5 {
- label = "beaglebone:green:usr3";
- gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
- default-state = "off";
+ cape_eeprom3: cape_eeprom3 at 57 {
+ compatible = "at,24c256";
+ reg = <0x57>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cape3_data: cape_data at 0 {
+ reg = <0 0x100>;
};
};
};
+
/include/ "tps65217.dtsi"
&tps {
+ /*
+ * Configure pmic to enter OFF-state instead of SLEEP-state ("RTC-only
+ * mode") at poweroff. Most BeagleBone versions do not support RTC-only
+ * mode and risk hardware damage if this mode is entered.
+ *
+ * For details, see linux-omap mailing list May 2015 thread
+ * [PATCH] ARM: dts: am335x-bone* enable pmic-shutdown-controller
+ * In particular, messages:
+ * http://www.spinics.net/lists/linux-omap/msg118585.html
+ * http://www.spinics.net/lists/linux-omap/msg118615.html
+ *
+ * You can override this later with
+ * &tps { /delete-property/ ti,pmic-shutdown-controller; }
+ * if you want to use RTC-only mode and made sure you are not affected
+ * by the hardware problems. (Tip: double-check by performing a current
+ * measurement after shutdown: it should be less than 1 mA.)
+ */
+ ti,pmic-shutdown-controller;
+
regulators {
dcdc1_reg: regulator at 0 {
+ regulator-name = "vdds_dpr";
regulator-always-on;
};
@@ -225,18 +333,22 @@
};
ldo1_reg: regulator at 3 {
+ regulator-name = "vio,vrtc,vdds";
regulator-always-on;
};
ldo2_reg: regulator at 4 {
+ regulator-name = "vdd_3v3aux";
regulator-always-on;
};
ldo3_reg: regulator at 5 {
+ regulator-name = "vdd_1v8";
regulator-always-on;
};
ldo4_reg: regulator at 6 {
+ regulator-name = "vdd_3v3a";
regulator-always-on;
};
};
@@ -256,11 +368,29 @@
pinctrl-names = "default", "sleep";
pinctrl-0 = <&cpsw_default>;
pinctrl-1 = <&cpsw_sleep>;
-
+ status = "okay";
};
&davinci_mdio {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&davinci_mdio_default>;
pinctrl-1 = <&davinci_mdio_sleep>;
+ status = "okay";
+};
+
+&mmc1 {
+ status = "okay";
+ bus-width = <0x4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+ cd-inverted;
+};
+
+&aes {
+ status = "okay";
+};
+
+&sham {
+ status = "okay";
};
diff --git a/arch/arm/dts/am335x-bone.dts b/arch/arm/dts/am335x-bone.dts
new file mode 100644
index 0000000..81441cc
--- /dev/null
+++ b/arch/arm/dts/am335x-bone.dts
@@ -0,0 +1,29 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+
+/ {
+ model = "TI AM335x BeagleBone";
+ compatible = "ti,am335x-bone", "ti,am33xx";
+ chosen {
+ stdout-path = &uart0;
+ };
+};
+
+&ldo3_reg {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+};
+
+&mmc1 {
+ vmmc-supply = <&ldo3_reg>;
+};
diff --git a/arch/arm/dts/am335x-boneblack.dts b/arch/arm/dts/am335x-boneblack.dts
index 197cadf..679248a 100644
--- a/arch/arm/dts/am335x-boneblack.dts
+++ b/arch/arm/dts/am335x-boneblack.dts
@@ -10,8 +10,80 @@
#include "am33xx.dtsi"
#include "am335x-bone-common.dtsi"
+/ {
+ model = "TI AM335x BeagleBone Black";
+ compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+ chosen {
+ stdout-path = &uart0;
+ };
+};
+
&ldo3_reg {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
+
+&mmc1 {
+ vmmc-supply = <&vmmcsd_fixed>;
+};
+
+&mmc2 {
+ vmmc-supply = <&vmmcsd_fixed>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins>;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&am33xx_pinmux {
+ nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
+ pinctrl-single,pins = <
+ 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
+ 0xa0 0x08 /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xa4 0x08 /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xa8 0x08 /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xac 0x08 /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xb0 0x08 /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xb4 0x08 /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xb8 0x08 /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xbc 0x08 /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xc0 0x08 /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xc4 0x08 /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xc8 0x08 /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xcc 0x08 /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xd0 0x08 /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xd4 0x08 /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xd8 0x08 /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xdc 0x08 /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+ 0xe0 0x00 /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+ 0xe4 0x00 /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+ 0xe8 0x00 /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+ 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+ >;
+ };
+ nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
+ pinctrl-single,pins = <
+ 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
+ >;
+ };
+};
+
+&lcdc {
+ status = "okay";
+};
+
+/ {
+ hdmi {
+ compatible = "ti,tilcdc,slave";
+ i2c = <&i2c0>;
+ pinctrl-names = "default", "off";
+ pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+ pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
+ status = "okay";
+ };
+};
+
+&rtc {
+ system-power-controller;
+};
diff --git a/arch/arm/dts/am335x-evm.dts b/arch/arm/dts/am335x-evm.dts
new file mode 100644
index 0000000..e1c5d4f
--- /dev/null
+++ b/arch/arm/dts/am335x-evm.dts
@@ -0,0 +1,765 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "TI AM335x EVM";
+ compatible = "ti,am335x-evm", "ti,am33xx";
+
+ chosen {
+ stdout-path = &uart0;
+ };
+
+ cpus {
+ cpu at 0 {
+ cpu0-supply = <&vdd1_reg>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ vbat: fixedregulator at 0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vbat";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ };
+
+ lis3_reg: fixedregulator at 1 {
+ compatible = "regulator-fixed";
+ regulator-name = "lis3_reg";
+ regulator-boot-on;
+ };
+
+ wlan_en_reg: fixedregulator at 2 {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan-en-regulator";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ /* WLAN_EN GPIO for this board - Bank1, pin16 */
+ gpio = <&gpio1 16 0>;
+
+ /* WLAN card specific delay */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+
+ matrix_keypad: matrix_keypad at 0 {
+ compatible = "gpio-matrix-keypad";
+ debounce-delay-ms = <5>;
+ col-scan-delay-us = <2>;
+
+ row-gpios = <&gpio1 25 GPIO_ACTIVE_HIGH /* Bank1, pin25 */
+ &gpio1 26 GPIO_ACTIVE_HIGH /* Bank1, pin26 */
+ &gpio1 27 GPIO_ACTIVE_HIGH>; /* Bank1, pin27 */
+
+ col-gpios = <&gpio1 21 GPIO_ACTIVE_HIGH /* Bank1, pin21 */
+ &gpio1 22 GPIO_ACTIVE_HIGH>; /* Bank1, pin22 */
+
+ linux,keymap = <0x0000008b /* MENU */
+ 0x0100009e /* BACK */
+ 0x02000069 /* LEFT */
+ 0x0001006a /* RIGHT */
+ 0x0101001c /* ENTER */
+ 0x0201006c>; /* DOWN */
+ };
+
+ gpio_keys: volume_keys at 0 {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+
+ switch at 9 {
+ label = "volume-up";
+ linux,code = <115>;
+ gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+ gpio-key,wakeup;
+ };
+
+ switch at 10 {
+ label = "volume-down";
+ linux,code = <114>;
+ gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+ gpio-key,wakeup;
+ };
+ };
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&ecap0 0 50000 0>;
+ brightness-levels = <0 51 53 56 62 75 101 152 255>;
+ default-brightness-level = <8>;
+ };
+
+ panel {
+ compatible = "ti,tilcdc,panel";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_pins_s0>;
+ panel-info {
+ ac-bias = <255>;
+ ac-bias-intrpt = <0>;
+ dma-burst-sz = <16>;
+ bpp = <32>;
+ fdd = <0x80>;
+ sync-edge = <0>;
+ sync-ctrl = <1>;
+ raster-order = <0>;
+ fifo-th = <0>;
+ };
+
+ display-timings {
+ 800x480p62 {
+ clock-frequency = <30000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hfront-porch = <39>;
+ hback-porch = <39>;
+ hsync-len = <47>;
+ vback-porch = <29>;
+ vfront-porch = <13>;
+ vsync-len = <2>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
+ };
+
+ sound {
+ compatible = "ti,da830-evm-audio";
+ ti,model = "AM335x-EVM";
+ ti,audio-codec = <&tlv320aic3106>;
+ ti,mcasp-controller = <&mcasp1>;
+ ti,codec-clock-rate = <12000000>;
+ ti,audio-routing =
+ "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT",
+ "LINE1L", "Line In",
+ "LINE1R", "Line In";
+ };
+};
+
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>;
+
+ matrix_keypad_s0: matrix_keypad_s0 {
+ pinctrl-single,pins = <
+ 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
+ 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a6.gpio1_22 */
+ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a9.gpio1_25 */
+ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a10.gpio1_26 */
+ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.gpio1_27 */
+ >;
+ };
+
+ volume_keys_s0: volume_keys_s0 {
+ pinctrl-single,pins = <
+ 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_sclk.gpio0_2 */
+ 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_d0.gpio0_3 */
+ >;
+ };
+
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ i2c1_pins: pinmux_i2c1_pins {
+ pinctrl-single,pins = <
+ 0x158 (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d1.i2c1_sda */
+ 0x15c (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_cs0.i2c1_scl */
+ >;
+ };
+
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ uart1_pins: pinmux_uart1_pins {
+ pinctrl-single,pins = <
+ 0x178 (PIN_INPUT | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */
+ 0x17C (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */
+ 0x180 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */
+ 0x184 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */
+ >;
+ };
+
+ clkout2_pin: pinmux_clkout2_pin {
+ pinctrl-single,pins = <
+ 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
+ >;
+ };
+
+ nandflash_pins_s0: nandflash_pins_s0 {
+ pinctrl-single,pins = <
+ 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */
+ 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */
+ 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */
+ 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */
+ 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */
+ 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */
+ 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */
+ 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */
+ 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */
+ 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */
+ 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */
+ 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */
+ 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */
+ 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */
+ 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */
+ >;
+ };
+
+ ecap0_pins: backlight_pins {
+ pinctrl-single,pins = <
+ 0x164 0x0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+ >;
+ };
+
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Slave 1 */
+ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */
+ 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */
+ 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */
+ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */
+ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */
+ 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */
+ >;
+ };
+
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ /* Slave 1 reset value */
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ 0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
+ >;
+ };
+
+ mmc3_pins: pinmux_mmc3_pins {
+ pinctrl-single,pins = <
+ 0x44 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a1.mmc2_dat0, INPUT_PULLUP | MODE3 */
+ 0x48 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a2.mmc2_dat1, INPUT_PULLUP | MODE3 */
+ 0x4C (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a3.mmc2_dat2, INPUT_PULLUP | MODE3 */
+ 0x78 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ben1.mmc2_dat3, INPUT_PULLUP | MODE3 */
+ 0x88 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_csn3.mmc2_cmd, INPUT_PULLUP | MODE3 */
+ 0x8C (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_clk.mmc2_clk, INPUT_PULLUP | MODE3 */
+ >;
+ };
+
+ wlan_pins: pinmux_wlan_pins {
+ pinctrl-single,pins = <
+ 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a0.gpio1_16 */
+ 0x19C (PIN_INPUT | MUX_MODE7) /* mcasp0_ahclkr.gpio3_17 */
+ 0x1AC (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* mcasp0_ahclkx.gpio3_21 */
+ >;
+ };
+
+ lcd_pins_s0: lcd_pins_s0 {
+ pinctrl-single,pins = <
+ 0x20 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad8.lcd_data23 */
+ 0x24 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad9.lcd_data22 */
+ 0x28 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad10.lcd_data21 */
+ 0x2c (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad11.lcd_data20 */
+ 0x30 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad12.lcd_data19 */
+ 0x34 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad13.lcd_data18 */
+ 0x38 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad14.lcd_data17 */
+ 0x3c (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad15.lcd_data16 */
+ 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */
+ 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */
+ 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */
+ 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */
+ 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */
+ 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */
+ 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */
+ 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */
+ 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */
+ 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */
+ 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */
+ 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */
+ 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */
+ 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */
+ 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */
+ 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */
+ 0xe0 (PIN_OUTPUT | MUX_MODE0) /* lcd_vsync.lcd_vsync */
+ 0xe4 (PIN_OUTPUT | MUX_MODE0) /* lcd_hsync.lcd_hsync */
+ 0xe8 (PIN_OUTPUT | MUX_MODE0) /* lcd_pclk.lcd_pclk */
+ 0xec (PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */
+ >;
+ };
+
+ am335x_evm_audio_pins: am335x_evm_audio_pins {
+ pinctrl-single,pins = <
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */
+ 0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
+ >;
+ };
+
+ dcan1_pins_default: dcan1_pins_default {
+ pinctrl-single,pins = <
+ 0x168 (PIN_OUTPUT | MUX_MODE2) /* uart0_ctsn.d_can1_tx */
+ 0x16c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* uart0_rtsn.d_can1_rx */
+ >;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: tps at 2d {
+ reg = <0x2d>;
+ };
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb_ctrl_mod {
+ status = "okay";
+};
+
+&usb0_phy {
+ status = "okay";
+};
+
+&usb1_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&cppi41dma {
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ status = "okay";
+ clock-frequency = <100000>;
+
+ lis331dlh: lis331dlh at 18 {
+ compatible = "st,lis331dlh", "st,lis3lv02d";
+ reg = <0x18>;
+ Vdd-supply = <&lis3_reg>;
+ Vdd_IO-supply = <&lis3_reg>;
+
+ st,click-single-x;
+ st,click-single-y;
+ st,click-single-z;
+ st,click-thresh-x = <10>;
+ st,click-thresh-y = <10>;
+ st,click-thresh-z = <10>;
+ st,irq1-click;
+ st,irq2-click;
+ st,wakeup-x-lo;
+ st,wakeup-x-hi;
+ st,wakeup-y-lo;
+ st,wakeup-y-hi;
+ st,wakeup-z-lo;
+ st,wakeup-z-hi;
+ st,min-limit-x = <120>;
+ st,min-limit-y = <120>;
+ st,min-limit-z = <140>;
+ st,max-limit-x = <550>;
+ st,max-limit-y = <550>;
+ st,max-limit-z = <750>;
+ };
+
+ tsl2550: tsl2550 at 39 {
+ compatible = "taos,tsl2550";
+ reg = <0x39>;
+ };
+
+ tmp275: tmp275 at 48 {
+ compatible = "ti,tmp275";
+ reg = <0x48>;
+ };
+
+ tlv320aic3106: tlv320aic3106 at 1b {
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+ status = "okay";
+
+ /* Regulators */
+ AVDD-supply = <&vaux2_reg>;
+ IOVDD-supply = <&vaux2_reg>;
+ DRVDD-supply = <&vaux2_reg>;
+ DVDD-supply = <&vbat>;
+ };
+};
+
+&lcdc {
+ status = "okay";
+};
+
+&elm {
+ status = "okay";
+};
+
+&epwmss0 {
+ status = "okay";
+
+ ecap0: ecap at 48300100 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ecap0_pins>;
+ };
+};
+
+&gpmc {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&nandflash_pins_s0>;
+ ranges = <0 0 0x08000000 0x1000000>; /* CS0: 16MB for NAND */
+ nand at 0,0 {
+ reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+ ti,nand-ecc-opt = "bch8";
+ ti,elm-id = <&elm>;
+ nand-bus-width = <8>;
+ gpmc,device-width = <1>;
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-on-ns = <0>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wait-on-read = "true";
+ gpmc,wait-on-write = "true";
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+ /* MTD partition table */
+ /* All SPL-* partitions are sized to minimal length
+ * which can be independently programmable. For
+ * NAND flash this is equal to size of erase-block */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition at 0 {
+ label = "NAND.SPL";
+ reg = <0x00000000 0x000020000>;
+ };
+ partition at 1 {
+ label = "NAND.SPL.backup1";
+ reg = <0x00020000 0x00020000>;
+ };
+ partition at 2 {
+ label = "NAND.SPL.backup2";
+ reg = <0x00040000 0x00020000>;
+ };
+ partition at 3 {
+ label = "NAND.SPL.backup3";
+ reg = <0x00060000 0x00020000>;
+ };
+ partition at 4 {
+ label = "NAND.u-boot-spl-os";
+ reg = <0x00080000 0x00040000>;
+ };
+ partition at 5 {
+ label = "NAND.u-boot";
+ reg = <0x000C0000 0x00100000>;
+ };
+ partition at 6 {
+ label = "NAND.u-boot-env";
+ reg = <0x001C0000 0x00020000>;
+ };
+ partition at 7 {
+ label = "NAND.u-boot-env.backup1";
+ reg = <0x001E0000 0x00020000>;
+ };
+ partition at 8 {
+ label = "NAND.kernel";
+ reg = <0x00200000 0x00800000>;
+ };
+ partition at 9 {
+ label = "NAND.file-system";
+ reg = <0x00A00000 0x0F600000>;
+ };
+ };
+};
+
+#include "tps65910.dtsi"
+
+&mcasp1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&am335x_evm_audio_pins>;
+
+ status = "okay";
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+ /* 4 serializers */
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 0 0 1 2
+ >;
+ tx-num-evt = <32>;
+ rx-num-evt = <32>;
+};
+
+&tps {
+ vcc1-supply = <&vbat>;
+ vcc2-supply = <&vbat>;
+ vcc3-supply = <&vbat>;
+ vcc4-supply = <&vbat>;
+ vcc5-supply = <&vbat>;
+ vcc6-supply = <&vbat>;
+ vcc7-supply = <&vbat>;
+ vccio-supply = <&vbat>;
+
+ regulators {
+ vrtc_reg: regulator at 0 {
+ regulator-always-on;
+ };
+
+ vio_reg: regulator at 1 {
+ regulator-always-on;
+ };
+
+ vdd1_reg: regulator at 2 {
+ /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+ regulator-name = "vdd_mpu";
+ regulator-min-microvolt = <912500>;
+ regulator-max-microvolt = <1312500>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd2_reg: regulator at 3 {
+ /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
+ regulator-name = "vdd_core";
+ regulator-min-microvolt = <912500>;
+ regulator-max-microvolt = <1150000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd3_reg: regulator at 4 {
+ regulator-always-on;
+ };
+
+ vdig1_reg: regulator at 5 {
+ regulator-always-on;
+ };
+
+ vdig2_reg: regulator at 6 {
+ regulator-always-on;
+ };
+
+ vpll_reg: regulator at 7 {
+ regulator-always-on;
+ };
+
+ vdac_reg: regulator at 8 {
+ regulator-always-on;
+ };
+
+ vaux1_reg: regulator at 9 {
+ regulator-always-on;
+ };
+
+ vaux2_reg: regulator at 10 {
+ regulator-always-on;
+ };
+
+ vaux33_reg: regulator at 11 {
+ regulator-always-on;
+ };
+
+ vmmc_reg: regulator at 12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+};
+
+&mac {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&cpsw_default>;
+ pinctrl-1 = <&cpsw_sleep>;
+ status = "okay";
+};
+
+&davinci_mdio {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&davinci_mdio_default>;
+ pinctrl-1 = <&davinci_mdio_sleep>;
+ status = "okay";
+};
+
+&cpsw_emac0 {
+ phy_id = <&davinci_mdio>, <0>;
+ phy-mode = "rgmii-txid";
+};
+
+&cpsw_emac1 {
+ phy_id = <&davinci_mdio>, <1>;
+ phy-mode = "rgmii-txid";
+};
+
+&tscadc {
+ status = "okay";
+ tsc {
+ ti,wires = <4>;
+ ti,x-plate-resistance = <200>;
+ ti,coordinate-readouts = <5>;
+ ti,wire-config = <0x00 0x11 0x22 0x33>;
+ ti,charge-delay = <0x400>;
+ };
+
+ adc {
+ ti,adc-channels = <4 5 6 7>;
+ };
+};
+
+&mmc1 {
+ status = "okay";
+ vmmc-supply = <&vmmc_reg>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+};
+
+&mmc3 {
+ /* these are on the crossbar and are outlined in the
+ xbar-event-map element */
+ dmas = <&edma 12
+ &edma 13>;
+ dma-names = "tx", "rx";
+ status = "okay";
+ vmmc-supply = <&wlan_en_reg>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins &wlan_pins>;
+ ti,non-removable;
+ ti,needs-special-hs-handling;
+ cap-power-off-card;
+ keep-power-in-suspend;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore at 0 {
+ compatible = "ti,wl1835";
+ reg = <2>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
+ };
+};
+
+&edma {
+ ti,edma-xbar-event-map = /bits/ 16 <1 12
+ 2 13>;
+};
+
+&sham {
+ status = "okay";
+};
+
+&aes {
+ status = "okay";
+};
+
+&dcan1 {
+ status = "disabled"; /* Enable only if Profile 1 is selected */
+ pinctrl-names = "default";
+ pinctrl-0 = <&dcan1_pins_default>;
+};
diff --git a/arch/arm/dts/am33xx-clocks.dtsi b/arch/arm/dts/am33xx-clocks.dtsi
new file mode 100644
index 0000000..afb4b3a
--- /dev/null
+++ b/arch/arm/dts/am33xx-clocks.dtsi
@@ -0,0 +1,646 @@
+/*
+ * Device Tree Source for AM33xx clock data
+ *
+ * Copyright (C) 2013 Texas Instruments, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+&scm_clocks {
+ sys_clkin_ck: sys_clkin_ck {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&virt_19200000_ck>, <&virt_24000000_ck>, <&virt_25000000_ck>, <&virt_26000000_ck>;
+ ti,bit-shift = <22>;
+ reg = <0x0040>;
+ };
+
+ adc_tsc_fck: adc_tsc_fck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&sys_clkin_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
+ dcan0_fck: dcan0_fck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&sys_clkin_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
+ dcan1_fck: dcan1_fck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&sys_clkin_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
+ mcasp0_fck: mcasp0_fck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&sys_clkin_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
+ mcasp1_fck: mcasp1_fck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&sys_clkin_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
+ smartreflex0_fck: smartreflex0_fck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&sys_clkin_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
+ smartreflex1_fck: smartreflex1_fck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&sys_clkin_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
+ sha0_fck: sha0_fck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&sys_clkin_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
+ aes0_fck: aes0_fck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&sys_clkin_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
+ rng_fck: rng_fck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&sys_clkin_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
+ ehrpwm0_tbclk: ehrpwm0_tbclk at 44e10664 {
+ #clock-cells = <0>;
+ compatible = "ti,gate-clock";
+ clocks = <&l4ls_gclk>;
+ ti,bit-shift = <0>;
+ reg = <0x0664>;
+ };
+
+ ehrpwm1_tbclk: ehrpwm1_tbclk at 44e10664 {
+ #clock-cells = <0>;
+ compatible = "ti,gate-clock";
+ clocks = <&l4ls_gclk>;
+ ti,bit-shift = <1>;
+ reg = <0x0664>;
+ };
+
+ ehrpwm2_tbclk: ehrpwm2_tbclk at 44e10664 {
+ #clock-cells = <0>;
+ compatible = "ti,gate-clock";
+ clocks = <&l4ls_gclk>;
+ ti,bit-shift = <2>;
+ reg = <0x0664>;
+ };
+};
+&prcm_clocks {
+ clk_32768_ck: clk_32768_ck {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ };
+
+ clk_rc32k_ck: clk_rc32k_ck {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32000>;
+ };
+
+ virt_19200000_ck: virt_19200000_ck {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <19200000>;
+ };
+
+ virt_24000000_ck: virt_24000000_ck {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ };
+
+ virt_25000000_ck: virt_25000000_ck {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ };
+
+ virt_26000000_ck: virt_26000000_ck {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <26000000>;
+ };
+
+ tclkin_ck: tclkin_ck {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <12000000>;
+ };
+
+ dpll_core_ck: dpll_core_ck {
+ #clock-cells = <0>;
+ compatible = "ti,am3-dpll-core-clock";
+ clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+ reg = <0x0490>, <0x045c>, <0x0468>;
+ };
+
+ dpll_core_x2_ck: dpll_core_x2_ck {
+ #clock-cells = <0>;
+ compatible = "ti,am3-dpll-x2-clock";
+ clocks = <&dpll_core_ck>;
+ };
+
+ dpll_core_m4_ck: dpll_core_m4_ck {
+ #clock-cells = <0>;
+ compatible = "ti,divider-clock";
+ clocks = <&dpll_core_x2_ck>;
+ ti,max-div = <31>;
+ reg = <0x0480>;
+ ti,index-starts-at-one;
+ };
+
+ dpll_core_m5_ck: dpll_core_m5_ck {
+ #clock-cells = <0>;
+ compatible = "ti,divider-clock";
+ clocks = <&dpll_core_x2_ck>;
+ ti,max-div = <31>;
+ reg = <0x0484>;
+ ti,index-starts-at-one;
+ };
+
+ dpll_core_m6_ck: dpll_core_m6_ck {
+ #clock-cells = <0>;
+ compatible = "ti,divider-clock";
+ clocks = <&dpll_core_x2_ck>;
+ ti,max-div = <31>;
+ reg = <0x04d8>;
+ ti,index-starts-at-one;
+ };
+
+ dpll_mpu_ck: dpll_mpu_ck {
+ #clock-cells = <0>;
+ compatible = "ti,am3-dpll-clock";
+ clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+ reg = <0x0488>, <0x0420>, <0x042c>;
+ };
+
+ dpll_mpu_m2_ck: dpll_mpu_m2_ck {
+ #clock-cells = <0>;
+ compatible = "ti,divider-clock";
+ clocks = <&dpll_mpu_ck>;
+ ti,max-div = <31>;
+ reg = <0x04a8>;
+ ti,index-starts-at-one;
+ };
+
+ dpll_ddr_ck: dpll_ddr_ck {
+ #clock-cells = <0>;
+ compatible = "ti,am3-dpll-no-gate-clock";
+ clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+ reg = <0x0494>, <0x0434>, <0x0440>;
+ };
+
+ dpll_ddr_m2_ck: dpll_ddr_m2_ck {
+ #clock-cells = <0>;
+ compatible = "ti,divider-clock";
+ clocks = <&dpll_ddr_ck>;
+ ti,max-div = <31>;
+ reg = <0x04a0>;
+ ti,index-starts-at-one;
+ };
+
+ dpll_ddr_m2_div2_ck: dpll_ddr_m2_div2_ck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&dpll_ddr_m2_ck>;
+ clock-mult = <1>;
+ clock-div = <2>;
+ };
+
+ dpll_disp_ck: dpll_disp_ck {
+ #clock-cells = <0>;
+ compatible = "ti,am3-dpll-no-gate-clock";
+ clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+ reg = <0x0498>, <0x0448>, <0x0454>;
+ };
+
+ dpll_disp_m2_ck: dpll_disp_m2_ck {
+ #clock-cells = <0>;
+ compatible = "ti,divider-clock";
+ clocks = <&dpll_disp_ck>;
+ ti,max-div = <31>;
+ reg = <0x04a4>;
+ ti,index-starts-at-one;
+ ti,set-rate-parent;
+ };
+
+ dpll_per_ck: dpll_per_ck {
+ #clock-cells = <0>;
+ compatible = "ti,am3-dpll-no-gate-j-type-clock";
+ clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+ reg = <0x048c>, <0x0470>, <0x049c>;
+ };
+
+ dpll_per_m2_ck: dpll_per_m2_ck {
+ #clock-cells = <0>;
+ compatible = "ti,divider-clock";
+ clocks = <&dpll_per_ck>;
+ ti,max-div = <31>;
+ reg = <0x04ac>;
+ ti,index-starts-at-one;
+ };
+
+ dpll_per_m2_div4_wkupdm_ck: dpll_per_m2_div4_wkupdm_ck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&dpll_per_m2_ck>;
+ clock-mult = <1>;
+ clock-div = <4>;
+ };
+
+ dpll_per_m2_div4_ck: dpll_per_m2_div4_ck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&dpll_per_m2_ck>;
+ clock-mult = <1>;
+ clock-div = <4>;
+ };
+
+ cefuse_fck: cefuse_fck {
+ #clock-cells = <0>;
+ compatible = "ti,gate-clock";
+ clocks = <&sys_clkin_ck>;
+ ti,bit-shift = <1>;
+ reg = <0x0a20>;
+ };
+
+ clk_24mhz: clk_24mhz {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&dpll_per_m2_ck>;
+ clock-mult = <1>;
+ clock-div = <8>;
+ };
+
+ clkdiv32k_ck: clkdiv32k_ck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&clk_24mhz>;
+ clock-mult = <1>;
+ clock-div = <732>;
+ };
+
+ clkdiv32k_ick: clkdiv32k_ick {
+ #clock-cells = <0>;
+ compatible = "ti,gate-clock";
+ clocks = <&clkdiv32k_ck>;
+ ti,bit-shift = <1>;
+ reg = <0x014c>;
+ };
+
+ l3_gclk: l3_gclk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&dpll_core_m4_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
+ pruss_ocp_gclk: pruss_ocp_gclk {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&l3_gclk>, <&dpll_disp_m2_ck>;
+ reg = <0x0530>;
+ };
+
+ mmu_fck: mmu_fck {
+ #clock-cells = <0>;
+ compatible = "ti,gate-clock";
+ clocks = <&dpll_core_m4_ck>;
+ ti,bit-shift = <1>;
+ reg = <0x0914>;
+ };
+
+ timer1_fck: timer1_fck {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&sys_clkin_ck>, <&clkdiv32k_ick>, <&tclkin_ck>, <&clk_rc32k_ck>, <&clk_32768_ck>;
+ reg = <0x0528>;
+ };
+
+ timer2_fck: timer2_fck {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+ reg = <0x0508>;
+ };
+
+ timer3_fck: timer3_fck {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+ reg = <0x050c>;
+ };
+
+ timer4_fck: timer4_fck {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+ reg = <0x0510>;
+ };
+
+ timer5_fck: timer5_fck {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+ reg = <0x0518>;
+ };
+
+ timer6_fck: timer6_fck {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+ reg = <0x051c>;
+ };
+
+ timer7_fck: timer7_fck {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+ reg = <0x0504>;
+ };
+
+ usbotg_fck: usbotg_fck {
+ #clock-cells = <0>;
+ compatible = "ti,gate-clock";
+ clocks = <&dpll_per_ck>;
+ ti,bit-shift = <8>;
+ reg = <0x047c>;
+ };
+
+ dpll_core_m4_div2_ck: dpll_core_m4_div2_ck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&dpll_core_m4_ck>;
+ clock-mult = <1>;
+ clock-div = <2>;
+ };
+
+ ieee5000_fck: ieee5000_fck {
+ #clock-cells = <0>;
+ compatible = "ti,gate-clock";
+ clocks = <&dpll_core_m4_div2_ck>;
+ ti,bit-shift = <1>;
+ reg = <0x00e4>;
+ };
+
+ wdt1_fck: wdt1_fck {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&clk_rc32k_ck>, <&clkdiv32k_ick>;
+ reg = <0x0538>;
+ };
+
+ l4_rtc_gclk: l4_rtc_gclk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&dpll_core_m4_ck>;
+ clock-mult = <1>;
+ clock-div = <2>;
+ };
+
+ l4hs_gclk: l4hs_gclk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&dpll_core_m4_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
+ l3s_gclk: l3s_gclk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&dpll_core_m4_div2_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
+ l4fw_gclk: l4fw_gclk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&dpll_core_m4_div2_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
+ l4ls_gclk: l4ls_gclk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&dpll_core_m4_div2_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
+ sysclk_div_ck: sysclk_div_ck {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&dpll_core_m4_ck>;
+ clock-mult = <1>;
+ clock-div = <1>;
+ };
+
+ cpsw_125mhz_gclk: cpsw_125mhz_gclk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&dpll_core_m5_ck>;
+ clock-mult = <1>;
+ clock-div = <2>;
+ };
+
+ cpsw_cpts_rft_clk: cpsw_cpts_rft_clk {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&dpll_core_m5_ck>, <&dpll_core_m4_ck>;
+ reg = <0x0520>;
+ };
+
+ gpio0_dbclk_mux_ck: gpio0_dbclk_mux_ck {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&clk_rc32k_ck>, <&clk_32768_ck>, <&clkdiv32k_ick>;
+ reg = <0x053c>;
+ };
+
+ gpio0_dbclk: gpio0_dbclk {
+ #clock-cells = <0>;
+ compatible = "ti,gate-clock";
+ clocks = <&gpio0_dbclk_mux_ck>;
+ ti,bit-shift = <18>;
+ reg = <0x0408>;
+ };
+
+ gpio1_dbclk: gpio1_dbclk {
+ #clock-cells = <0>;
+ compatible = "ti,gate-clock";
+ clocks = <&clkdiv32k_ick>;
+ ti,bit-shift = <18>;
+ reg = <0x00ac>;
+ };
+
+ gpio2_dbclk: gpio2_dbclk {
+ #clock-cells = <0>;
+ compatible = "ti,gate-clock";
+ clocks = <&clkdiv32k_ick>;
+ ti,bit-shift = <18>;
+ reg = <0x00b0>;
+ };
+
+ gpio3_dbclk: gpio3_dbclk {
+ #clock-cells = <0>;
+ compatible = "ti,gate-clock";
+ clocks = <&clkdiv32k_ick>;
+ ti,bit-shift = <18>;
+ reg = <0x00b4>;
+ };
+
+ lcd_gclk: lcd_gclk {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&dpll_disp_m2_ck>, <&dpll_core_m5_ck>, <&dpll_per_m2_ck>;
+ reg = <0x0534>;
+ ti,set-rate-parent;
+ };
+
+ mmc_clk: mmc_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&dpll_per_m2_ck>;
+ clock-mult = <1>;
+ clock-div = <2>;
+ };
+
+ gfx_fclk_clksel_ck: gfx_fclk_clksel_ck {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&dpll_core_m4_ck>, <&dpll_per_m2_ck>;
+ ti,bit-shift = <1>;
+ reg = <0x052c>;
+ };
+
+ gfx_fck_div_ck: gfx_fck_div_ck {
+ #clock-cells = <0>;
+ compatible = "ti,divider-clock";
+ clocks = <&gfx_fclk_clksel_ck>;
+ reg = <0x052c>;
+ ti,max-div = <2>;
+ };
+
+ sysclkout_pre_ck: sysclkout_pre_ck {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&clk_32768_ck>, <&l3_gclk>, <&dpll_ddr_m2_ck>, <&dpll_per_m2_ck>, <&lcd_gclk>;
+ reg = <0x0700>;
+ };
+
+ clkout2_div_ck: clkout2_div_ck {
+ #clock-cells = <0>;
+ compatible = "ti,divider-clock";
+ clocks = <&sysclkout_pre_ck>;
+ ti,bit-shift = <3>;
+ ti,max-div = <8>;
+ reg = <0x0700>;
+ };
+
+ dbg_sysclk_ck: dbg_sysclk_ck {
+ #clock-cells = <0>;
+ compatible = "ti,gate-clock";
+ clocks = <&sys_clkin_ck>;
+ ti,bit-shift = <19>;
+ reg = <0x0414>;
+ };
+
+ dbg_clka_ck: dbg_clka_ck {
+ #clock-cells = <0>;
+ compatible = "ti,gate-clock";
+ clocks = <&dpll_core_m4_ck>;
+ ti,bit-shift = <30>;
+ reg = <0x0414>;
+ };
+
+ stm_pmd_clock_mux_ck: stm_pmd_clock_mux_ck {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&dbg_sysclk_ck>, <&dbg_clka_ck>;
+ ti,bit-shift = <22>;
+ reg = <0x0414>;
+ };
+
+ trace_pmd_clk_mux_ck: trace_pmd_clk_mux_ck {
+ #clock-cells = <0>;
+ compatible = "ti,mux-clock";
+ clocks = <&dbg_sysclk_ck>, <&dbg_clka_ck>;
+ ti,bit-shift = <20>;
+ reg = <0x0414>;
+ };
+
+ stm_clk_div_ck: stm_clk_div_ck {
+ #clock-cells = <0>;
+ compatible = "ti,divider-clock";
+ clocks = <&stm_pmd_clock_mux_ck>;
+ ti,bit-shift = <27>;
+ ti,max-div = <64>;
+ reg = <0x0414>;
+ ti,index-power-of-two;
+ };
+
+ trace_clk_div_ck: trace_clk_div_ck {
+ #clock-cells = <0>;
+ compatible = "ti,divider-clock";
+ clocks = <&trace_pmd_clk_mux_ck>;
+ ti,bit-shift = <24>;
+ ti,max-div = <64>;
+ reg = <0x0414>;
+ ti,index-power-of-two;
+ };
+
+ clkout2_ck: clkout2_ck {
+ #clock-cells = <0>;
+ compatible = "ti,gate-clock";
+ clocks = <&clkout2_div_ck>;
+ ti,bit-shift = <7>;
+ reg = <0x0700>;
+ };
+};
+
+&prcm_clockdomains {
+ clk_24mhz_clkdm: clk_24mhz_clkdm {
+ compatible = "ti,clockdomain";
+ clocks = <&clkdiv32k_ick>;
+ };
+};
diff --git a/arch/arm/dts/am33xx.dtsi b/arch/arm/dts/am33xx.dtsi
index f9c5da9..21fcc44 100644
--- a/arch/arm/dts/am33xx.dtsi
+++ b/arch/arm/dts/am33xx.dtsi
@@ -18,6 +18,9 @@
interrupt-parent = <&intc>;
aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &uart2;
@@ -30,6 +33,8 @@
usb1 = &usb1;
phy0 = &usb0_phy;
phy1 = &usb1_phy;
+ ethernet0 = &cpsw_emac0;
+ ethernet1 = &cpsw_emac1;
};
cpus {
@@ -53,12 +58,21 @@
275000 1125000
>;
voltage-tolerance = <2>; /* 2 percentage */
+
+ clocks = <&dpll_mpu_ck>;
+ clock-names = "cpu";
+
clock-latency = <300000>; /* From omap-cpufreq driver */
};
};
+ pmu {
+ compatible = "arm,cortex-a8-pmu";
+ interrupts = <3>;
+ };
+
/*
- * The soc node represents the soc top level view. It is uses for IPs
+ * The soc node represents the soc top level view. It is used for IPs
* that are not memory mapped in the MPU view or for the MPU itself.
*/
soc {
@@ -69,19 +83,10 @@
};
};
- am33xx_pinmux: pinmux at 44e10800 {
- compatible = "pinctrl-single";
- reg = <0x44e10800 0x0238>;
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-single,register-width = <32>;
- pinctrl-single,function-mask = <0x7f>;
- };
-
/*
* XXX: Use a flat representation of the AM33XX interconnect.
- * The real AM33XX interconnect network is quite complex.Since
- * that will not bring real advantage to represent that in DT
+ * The real AM33XX interconnect network is quite complex. Since
+ * it will not bring real advantage to represent that in DT
* for the moment, just use a fake OCP bus entry to represent
* the whole bus hierarchy.
*/
@@ -92,21 +97,81 @@
ranges;
ti,hwmods = "l3_main";
+ l4_wkup: l4_wkup at 44c00000 {
+ compatible = "ti,am3-l4-wkup", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x44c00000 0x280000>;
+
+ prcm: prcm at 200000 {
+ compatible = "ti,am3-prcm";
+ reg = <0x200000 0x4000>;
+
+ prcm_clocks: clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ prcm_clockdomains: clockdomains {
+ };
+ };
+
+ scm: scm at 210000 {
+ compatible = "ti,am3-scm", "simple-bus";
+ reg = <0x210000 0x2000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x210000 0x2000>;
+
+ am33xx_pinmux: pinmux at 800 {
+ compatible = "pinctrl-single";
+ reg = <0x800 0x238>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x7f>;
+ };
+
+ scm_conf: scm_conf at 0 {
+ compatible = "syscon";
+ reg = <0x0 0x800>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ scm_clocks: clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ scm_clockdomains: clockdomains {
+ };
+ };
+ };
+
intc: interrupt-controller at 48200000 {
- compatible = "ti,omap2-intc";
+ compatible = "ti,am33xx-intc";
interrupt-controller;
#interrupt-cells = <1>;
- ti,intc-size = <128>;
reg = <0x48200000 0x1000>;
};
+ edma: edma at 49000000 {
+ compatible = "ti,edma3";
+ ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
+ reg = <0x49000000 0x10000>,
+ <0x44e10f90 0x40>;
+ interrupts = <12 13 14>;
+ #dma-cells = <1>;
+ };
+
gpio0: gpio at 44e07000 {
compatible = "ti,omap4-gpio";
ti,hwmods = "gpio1";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
reg = <0x44e07000 0x1000>;
interrupts = <96>;
};
@@ -117,7 +182,7 @@
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
reg = <0x4804c000 0x1000>;
interrupts = <98>;
};
@@ -128,7 +193,7 @@
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
reg = <0x481ac000 0x1000>;
interrupts = <32>;
};
@@ -139,7 +204,7 @@
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
reg = <0x481ae000 0x1000>;
interrupts = <62>;
};
@@ -151,6 +216,8 @@
reg = <0x44e09000 0x2000>;
interrupts = <72>;
status = "disabled";
+ dmas = <&edma 26>, <&edma 27>;
+ dma-names = "tx", "rx";
};
uart1: serial at 48022000 {
@@ -160,6 +227,8 @@
reg = <0x48022000 0x2000>;
interrupts = <73>;
status = "disabled";
+ dmas = <&edma 28>, <&edma 29>;
+ dma-names = "tx", "rx";
};
uart2: serial at 48024000 {
@@ -169,6 +238,8 @@
reg = <0x48024000 0x2000>;
interrupts = <74>;
status = "disabled";
+ dmas = <&edma 30>, <&edma 31>;
+ dma-names = "tx", "rx";
};
uart3: serial at 481a6000 {
@@ -228,6 +299,51 @@
status = "disabled";
};
+ mmc1: mmc at 48060000 {
+ compatible = "ti,omap4-hsmmc";
+ ti,hwmods = "mmc1";
+ ti,dual-volt;
+ ti,needs-special-reset;
+ ti,needs-special-hs-handling;
+ dmas = <&edma 24
+ &edma 25>;
+ dma-names = "tx", "rx";
+ interrupts = <64>;
+ interrupt-parent = <&intc>;
+ reg = <0x48060000 0x1000>;
+ status = "disabled";
+ };
+
+ mmc2: mmc at 481d8000 {
+ compatible = "ti,omap4-hsmmc";
+ ti,hwmods = "mmc2";
+ ti,needs-special-reset;
+ dmas = <&edma 2
+ &edma 3>;
+ dma-names = "tx", "rx";
+ interrupts = <28>;
+ interrupt-parent = <&intc>;
+ reg = <0x481d8000 0x1000>;
+ status = "disabled";
+ };
+
+ mmc3: mmc at 47810000 {
+ compatible = "ti,omap4-hsmmc";
+ ti,hwmods = "mmc3";
+ ti,needs-special-reset;
+ interrupts = <29>;
+ interrupt-parent = <&intc>;
+ reg = <0x47810000 0x1000>;
+ status = "disabled";
+ };
+
+ hwspinlock: spinlock at 480ca000 {
+ compatible = "ti,omap4-hwspinlock";
+ reg = <0x480ca000 0x1000>;
+ ti,hwmods = "spinlock";
+ #hwlock-cells = <1>;
+ };
+
wdt2: wdt at 44e35000 {
compatible = "ti,omap3-wdt";
ti,hwmods = "wd_timer2";
@@ -235,24 +351,42 @@
interrupts = <91>;
};
- dcan0: d_can at 481cc000 {
- compatible = "bosch,d_can";
+ dcan0: can at 481cc000 {
+ compatible = "ti,am3352-d_can";
ti,hwmods = "d_can0";
- reg = <0x481cc000 0x2000
- 0x44e10644 0x4>;
+ reg = <0x481cc000 0x2000>;
+ clocks = <&dcan0_fck>;
+ clock-names = "fck";
+ syscon-raminit = <&scm_conf 0x644 0>;
interrupts = <52>;
status = "disabled";
};
- dcan1: d_can at 481d0000 {
- compatible = "bosch,d_can";
+ dcan1: can at 481d0000 {
+ compatible = "ti,am3352-d_can";
ti,hwmods = "d_can1";
- reg = <0x481d0000 0x2000
- 0x44e10644 0x4>;
+ reg = <0x481d0000 0x2000>;
+ clocks = <&dcan1_fck>;
+ clock-names = "fck";
+ syscon-raminit = <&scm_conf 0x644 1>;
interrupts = <55>;
status = "disabled";
};
+ mailbox: mailbox at 480C8000 {
+ compatible = "ti,omap4-mailbox";
+ reg = <0x480C8000 0x200>;
+ interrupts = <77>;
+ ti,hwmods = "mailbox";
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <8>;
+ mbox_wkupm3: wkup_m3 {
+ ti,mbox-tx = <0 0 0>;
+ ti,mbox-rx = <0 0 3>;
+ };
+ };
+
timer1: timer at 44e31000 {
compatible = "ti,am335x-timer-1ms";
reg = <0x44e31000 0x400>;
@@ -307,8 +441,8 @@
ti,timer-pwm;
};
- rtc at 44e3e000 {
- compatible = "ti,da830-rtc";
+ rtc: rtc at 44e3e000 {
+ compatible = "ti,am3352-rtc", "ti,da830-rtc";
reg = <0x44e3e000 0x1000>;
interrupts = <75
76>;
@@ -323,6 +457,11 @@
interrupts = <65>;
ti,spi-num-cs = <2>;
ti,hwmods = "spi0";
+ dmas = <&edma 16
+ &edma 17
+ &edma 18
+ &edma 19>;
+ dma-names = "tx0", "rx0", "tx1", "rx1";
status = "disabled";
};
@@ -334,6 +473,11 @@
interrupts = <125>;
ti,spi-num-cs = <2>;
ti,hwmods = "spi1";
+ dmas = <&edma 42
+ &edma 43
+ &edma 44
+ &edma 45>;
+ dma-names = "tx0", "rx0", "tx1", "rx1";
status = "disabled";
};
@@ -346,7 +490,7 @@
ti,hwmods = "usb_otg_hs";
status = "disabled";
- ctrl_mod: control at 44e10000 {
+ usb_ctrl_mod: control at 44e10620 {
compatible = "ti,am335x-usb-ctrl-module";
reg = <0x44e10620 0x10
0x44e10648 0x4>;
@@ -359,7 +503,7 @@
reg = <0x47401300 0x100>;
reg-names = "phy";
status = "disabled";
- ti,ctrl_mod = <&ctrl_mod>;
+ ti,ctrl_mod = <&usb_ctrl_mod>;
};
usb0: usb at 47401000 {
@@ -407,7 +551,7 @@
reg = <0x47401b00 0x100>;
reg-names = "phy";
status = "disabled";
- ti,ctrl_mod = <&ctrl_mod>;
+ ti,ctrl_mod = <&usb_ctrl_mod>;
};
usb1: usb at 47401800 {
@@ -449,7 +593,7 @@
"tx14", "tx15";
};
- cppi41dma: dma-controller at 07402000 {
+ cppi41dma: dma-controller at 47402000 {
compatible = "ti,am3359-cppi41";
reg = <0x47400000 0x1000
0x47402000 0x1000
@@ -480,6 +624,8 @@
compatible = "ti,am33xx-ecap";
#pwm-cells = <3>;
reg = <0x48300100 0x80>;
+ interrupts = <31>;
+ interrupt-names = "ecap0";
ti,hwmods = "ecap0";
status = "disabled";
};
@@ -508,6 +654,8 @@
compatible = "ti,am33xx-ecap";
#pwm-cells = <3>;
reg = <0x48302100 0x80>;
+ interrupts = <47>;
+ interrupt-names = "ecap1";
ti,hwmods = "ecap1";
status = "disabled";
};
@@ -536,6 +684,8 @@
compatible = "ti,am33xx-ecap";
#pwm-cells = <3>;
reg = <0x48304100 0x80>;
+ interrupts = <61>;
+ interrupt-names = "ecap2";
ti,hwmods = "ecap2";
status = "disabled";
};
@@ -552,6 +702,8 @@
mac: ethernet at 4a100000 {
compatible = "ti,cpsw";
ti,hwmods = "cpgmac0";
+ clocks = <&cpsw_125mhz_gclk>, <&cpsw_cpts_rft_clk>;
+ clock-names = "fck", "cpts";
cpdma_channels = <8>;
ale_entries = <1024>;
bd_ram_size = <0x2000>;
@@ -575,6 +727,8 @@
*/
interrupts = <40 41 42 43>;
ranges;
+ syscon = <&scm_conf>;
+ status = "disabled";
davinci_mdio: mdio at 4a101000 {
compatible = "ti,davinci_mdio";
@@ -583,6 +737,7 @@
ti,hwmods = "davinci_mdio";
bus_freq = <1000000>;
reg = <0x4a101000 0x100>;
+ status = "disabled";
};
cpsw_emac0: slave at 4a100200 {
@@ -594,12 +749,17 @@
/* Filled in by U-Boot */
mac-address = [ 00 00 00 00 00 00 ];
};
+
+ phy_sel: cpsw-phy-sel at 44e10650 {
+ compatible = "ti,am3352-cpsw-phy-sel";
+ reg= <0x44e10650 0x4>;
+ reg-names = "gmii-sel";
+ };
};
ocmcram: ocmcram at 40300000 {
- compatible = "ti,am3352-ocmcram";
- reg = <0x40300000 0x10000>;
- ti,hwmods = "ocmcram";
+ compatible = "mmio-sram";
+ reg = <0x40300000 0x10000>; /* 64k */
};
wkup_m3: wkup_m3 at 44d00000 {
@@ -607,6 +767,7 @@
reg = <0x44d00000 0x4000 /* M3 UMEM */
0x44d80000 0x2000>; /* M3 DMEM */
ti,hwmods = "wkup_m3";
+ ti,no-reset-on-init;
};
elm: elm at 48080000 {
@@ -617,6 +778,15 @@
status = "disabled";
};
+ lcdc: lcdc at 4830e000 {
+ compatible = "ti,am33xx-tilcdc";
+ reg = <0x4830e000 0x1000>;
+ interrupt-parent = <&intc>;
+ interrupts = <36>;
+ ti,hwmods = "lcdc";
+ status = "disabled";
+ };
+
tscadc: tscadc at 44e0d000 {
compatible = "ti,am3359-tscadc";
reg = <0x44e0d000 0x1000>;
@@ -637,6 +807,7 @@
gpmc: gpmc at 50000000 {
compatible = "ti,am3352-gpmc";
ti,hwmods = "gpmc";
+ ti,no-idle-on-init;
reg = <0x50000000 0x2000>;
interrupts = <100>;
gpmc,num-cs = <7>;
@@ -645,5 +816,61 @@
#size-cells = <1>;
status = "disabled";
};
+
+ sham: sham at 53100000 {
+ compatible = "ti,omap4-sham";
+ ti,hwmods = "sham";
+ reg = <0x53100000 0x200>;
+ interrupts = <109>;
+ dmas = <&edma 36>;
+ dma-names = "rx";
+ };
+
+ aes: aes at 53500000 {
+ compatible = "ti,omap4-aes";
+ ti,hwmods = "aes";
+ reg = <0x53500000 0xa0>;
+ interrupts = <103>;
+ dmas = <&edma 6>,
+ <&edma 5>;
+ dma-names = "tx", "rx";
+ };
+
+ mcasp0: mcasp at 48038000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ ti,hwmods = "mcasp0";
+ reg = <0x48038000 0x2000>,
+ <0x46000000 0x400000>;
+ reg-names = "mpu", "dat";
+ interrupts = <80>, <81>;
+ interrupt-names = "tx", "rx";
+ status = "disabled";
+ dmas = <&edma 8>,
+ <&edma 9>;
+ dma-names = "tx", "rx";
+ };
+
+ mcasp1: mcasp at 4803C000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ ti,hwmods = "mcasp1";
+ reg = <0x4803C000 0x2000>,
+ <0x46400000 0x400000>;
+ reg-names = "mpu", "dat";
+ interrupts = <82>, <83>;
+ interrupt-names = "tx", "rx";
+ status = "disabled";
+ dmas = <&edma 10>,
+ <&edma 11>;
+ dma-names = "tx", "rx";
+ };
+
+ rng: rng at 48310000 {
+ compatible = "ti,omap4-rng";
+ ti,hwmods = "rng";
+ reg = <0x48310000 0x2000>;
+ interrupts = <111>;
+ };
};
};
+
+/include/ "am33xx-clocks.dtsi"
diff --git a/arch/arm/dts/tps65910.dtsi b/arch/arm/dts/tps65910.dtsi
new file mode 100644
index 0000000..b0ac665
--- /dev/null
+++ b/arch/arm/dts/tps65910.dtsi
@@ -0,0 +1,91 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * Integrated Power Management Chip
+ * http://www.ti.com/lit/ds/symlink/tps65910.pdf
+ */
+
+&tps {
+ compatible = "ti,tps65910";
+
+ regulators {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vrtc_reg: regulator at 0 {
+ reg = <0>;
+ regulator-compatible = "vrtc";
+ };
+
+ vio_reg: regulator at 1 {
+ reg = <1>;
+ regulator-compatible = "vio";
+ };
+
+ vdd1_reg: regulator at 2 {
+ reg = <2>;
+ regulator-compatible = "vdd1";
+ };
+
+ vdd2_reg: regulator at 3 {
+ reg = <3>;
+ regulator-compatible = "vdd2";
+ };
+
+ vdd3_reg: regulator at 4 {
+ reg = <4>;
+ regulator-compatible = "vdd3";
+ };
+
+ vdig1_reg: regulator at 5 {
+ reg = <5>;
+ regulator-compatible = "vdig1";
+ };
+
+ vdig2_reg: regulator at 6 {
+ reg = <6>;
+ regulator-compatible = "vdig2";
+ };
+
+ vpll_reg: regulator at 7 {
+ reg = <7>;
+ regulator-compatible = "vpll";
+ };
+
+ vdac_reg: regulator at 8 {
+ reg = <8>;
+ regulator-compatible = "vdac";
+ };
+
+ vaux1_reg: regulator at 9 {
+ reg = <9>;
+ regulator-compatible = "vaux1";
+ };
+
+ vaux2_reg: regulator at 10 {
+ reg = <10>;
+ regulator-compatible = "vaux2";
+ };
+
+ vaux33_reg: regulator at 11 {
+ reg = <11>;
+ regulator-compatible = "vaux33";
+ };
+
+ vmmc_reg: regulator at 12 {
+ reg = <12>;
+ regulator-compatible = "vmmc";
+ };
+
+ vbb_reg: regulator at 13 {
+ reg = <13>;
+ regulator-compatible = "vbb";
+ };
+ };
+};
diff --git a/configs/am335x_gp_evm_defconfig b/configs/am335x_gp_evm_defconfig
new file mode 100644
index 0000000..62d3b6b
--- /dev/null
+++ b/configs/am335x_gp_evm_defconfig
@@ -0,0 +1,14 @@
+CONFIG_ARM=y
+CONFIG_TARGET_AM335X_EVM=y
+CONFIG_DEFAULT_DEVICE_TREE="am335x-evm"
+CONFIG_SPL=y
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_STACK_R_ADDR=0x82000000
+CONFIG_SYS_EXTRA_OPTIONS="NAND"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_DISABLE_OF_CONTROL=y
+CONFIG_SPI_FLASH=y
+CONFIG_RSA=y
--
1.7.9.5
More information about the U-Boot
mailing list