[U-Boot] [PATCH 3/3][v3] imx: usb: ehci-mx6: add usb support for imx7d soc
Adrian Alonso
aalonso at freescale.com
Thu Aug 6 22:43:17 CEST 2015
Extend ehci-mx6 usb driver to support imx7d usb
Signed-off-by: Adrian Alonso <aalonso at freescale.com>
---
Changes for V2:
Add usb_power_config and usb_phy_mode for usb otg id detection for imx7d
Changes for V3:
Fix identation for usbnc_regs struct
drivers/usb/host/Makefile | 1 +
drivers/usb/host/ehci-mx6.c | 100 +++++++++++++++++++++++++++++++++++---------
2 files changed, 82 insertions(+), 19 deletions(-)
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 6cc3bbd..8537b6b 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -36,6 +36,7 @@ obj-$(CONFIG_USB_EHCI_MXC) += ehci-mxc.o
obj-$(CONFIG_USB_EHCI_MXS) += ehci-mxs.o
obj-$(CONFIG_USB_EHCI_MX5) += ehci-mx5.o
obj-$(CONFIG_USB_EHCI_MX6) += ehci-mx6.o
+obj-$(CONFIG_USB_EHCI_MX7) += ehci-mx6.o
obj-$(CONFIG_USB_EHCI_OMAP) += ehci-omap.o
obj-$(CONFIG_USB_EHCI_PPC4XX) += ehci-ppc4xx.o
obj-$(CONFIG_USB_EHCI_MARVELL) += ehci-marvell.o
diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index 1f5b056..54f8684 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -45,7 +45,10 @@
#define ANADIG_USB2_PLL_480_CTRL_POWER 0x00001000
#define ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS 0x00000040
-
+#define USBNC_OFFSET 0x200
+#define USBNC_PHYSTATUS_ID_DIG (1 << 4) /* otg_id status */
+#define USBNC_PHYCFG2_ACAENB (1 << 4) /* otg_id detection enable */
+#define UCTRL_PM (1 << 9) /* OTG Power Mask */
#define UCTRL_OVER_CUR_POL (1 << 8) /* OTG Polarity of Overcurrent */
#define UCTRL_OVER_CUR_DIS (1 << 7) /* Disable OTG Overcurrent Detection */
@@ -53,6 +56,7 @@
#define UCMD_RUN_STOP (1 << 0) /* controller run/stop */
#define UCMD_RESET (1 << 1) /* controller reset */
+#if defined(CONFIG_MX6)
static const unsigned phy_bases[] = {
USB_PHY0_BASE_ADDR,
USB_PHY1_BASE_ADDR,
@@ -153,6 +157,23 @@ static int usb_phy_enable(int index, struct usb_ehci *ehci)
return 0;
}
+int usb_phy_mode(int port)
+{
+ void __iomem *phy_reg;
+ void __iomem *phy_ctrl;
+ u32 val;
+
+ phy_reg = (void __iomem *)phy_bases[port];
+ phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL);
+
+ val = readl(phy_ctrl);
+
+ if (val & USBPHY_CTRL_OTG_ID)
+ return USB_INIT_DEVICE;
+ else
+ return USB_INIT_HOST;
+}
+
/* Base address for this IP block is 0x02184800 */
struct usbnc_regs {
u32 ctrl[4]; /* otg/host1-3 */
@@ -161,12 +182,57 @@ struct usbnc_regs {
u32 otg_phy_ctrl_0;
u32 uh1_phy_ctrl_0;
};
+#elif defined(CONFIG_MX7)
+struct usbnc_regs {
+ u32 ctrl1;
+ u32 ctrl2;
+ u32 reserve1[10];
+ u32 phy_cfg1;
+ u32 phy_cfg2;
+ u32 phy_status;
+ u32 reserve2[4];
+ u32 adp_cfg1;
+ u32 adp_cfg2;
+ u32 adp_status;
+};
+
+static void usb_power_config(int index)
+{
+ struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
+ (0x10000 * index) + USBNC_OFFSET);
+ void __iomem *phy_cfg2 = (void __iomem *)(&usbnc->phy_cfg2);
+
+ /* Enable usb_otg_id detection */
+ setbits_le32(phy_cfg2, USBNC_PHYCFG2_ACAENB);
+}
+
+int usb_phy_mode(int port)
+{
+ struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
+ (0x10000 * port) + USBNC_OFFSET);
+ void __iomem *status = (void __iomem *)(&usbnc->phy_status);
+ u32 val;
+
+ val = readl(status);
+
+ if (val & USBNC_PHYSTATUS_ID_DIG)
+ return USB_INIT_DEVICE;
+ else
+ return USB_INIT_HOST;
+}
+#endif
static void usb_oc_config(int index)
{
+#if defined(CONFIG_MX6)
struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
USB_OTHERREGS_OFFSET);
void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]);
+#elif defined(CONFIG_MX7)
+ struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
+ (0x10000 * index) + USBNC_OFFSET);
+ void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl1);
+#endif
#if CONFIG_MACH_TYPE == MACH_TYPE_MX6Q_ARM2
/* mx6qarm2 seems to required a different setting*/
@@ -175,24 +241,11 @@ static void usb_oc_config(int index)
setbits_le32(ctrl, UCTRL_OVER_CUR_POL);
#endif
+#if defined(CONFIG_MX6)
setbits_le32(ctrl, UCTRL_OVER_CUR_DIS);
-}
-
-int usb_phy_mode(int port)
-{
- void __iomem *phy_reg;
- void __iomem *phy_ctrl;
- u32 val;
-
- phy_reg = (void __iomem *)phy_bases[port];
- phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL);
-
- val = readl(phy_ctrl);
-
- if (val & USBPHY_CTRL_OTG_ID)
- return USB_INIT_DEVICE;
- else
- return USB_INIT_HOST;
+#elif defined(CONFIG_MX7)
+ setbits_le32(ctrl, UCTRL_OVER_CUR_DIS | UCTRL_PM);
+#endif
}
/**
@@ -245,8 +298,13 @@ int ehci_hcd_init(int index, enum usb_init_type init,
struct ehci_hccr **hccr, struct ehci_hcor **hcor)
{
enum usb_init_type type;
+#if defined(CONFIG_MX6)
+ u32 controller_spacing = 0x200;
+#elif defined(CONFIG_MX7)
+ u32 controller_spacing = 0x10000;
+#endif
struct usb_ehci *ehci = (struct usb_ehci *)(USB_BASE_ADDR +
- (0x200 * index));
+ (controller_spacing * index));
if (index > 3)
return -EINVAL;
@@ -258,8 +316,11 @@ int ehci_hcd_init(int index, enum usb_init_type init,
usb_power_config(index);
usb_oc_config(index);
+
+#if defined(CONFIG_MX6)
usb_internal_phy_clock_gate(index, 1);
usb_phy_enable(index, ehci);
+#endif
type = board_usb_phy_mode(index);
*hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
@@ -272,6 +333,7 @@ int ehci_hcd_init(int index, enum usb_init_type init,
return -ENODEV;
if (type == USB_INIT_DEVICE)
return 0;
+
setbits_le32(&ehci->usbmode, CM_HOST);
writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc);
setbits_le32(&ehci->portsc, USB_EN);
--
2.1.4
More information about the U-Boot
mailing list