[U-Boot] [PATCH 4/4] armv8: ls2085qds: Add support of X-QSGMII-16PORT riser card
Prabhakar Kushwaha
prabhakar at freescale.com
Fri Aug 7 14:31:51 CEST 2015
The X-QSGMII-16PORT is a 4xQSGMII/8xSGMII riser card with eighth SerDes
interfaces implemented in PCIe form factor board.
It supports followings
- Card can operate with up to 4 QSGMII lane simultaneously
- Card can operate with up to 8 SGMII lane simultaneously
Add support of X-QSGMII-16PORT riser card.
This patch also take care of back-ward compatiblity with old SGMII rise cards
used on LS2085QDS Platform.
Signed-off-by: King Chung Lo at freescale.com <KingChungLo at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
---
board/freescale/ls2085aqds/README | 81 +++++++
board/freescale/ls2085aqds/eth.c | 466 +++++++++++++++++++++++++++++++++++++-
include/configs/ls2085aqds.h | 17 ++
3 files changed, 553 insertions(+), 11 deletions(-)
diff --git a/board/freescale/ls2085aqds/README b/board/freescale/ls2085aqds/README
index 11b2e79..e4a6f69 100644
--- a/board/freescale/ls2085aqds/README
+++ b/board/freescale/ls2085aqds/README
@@ -146,3 +146,84 @@ below:
earlycon=uart8250,mmio,0x21c0600,115200 default_hugepagesz=2m hugepagesz=2m
hugepages=16 mem=2048M'
+
+X-QSGMII-16PORT riser card
+----------------------------
+The X-QSGMII-16PORT is a 4xQSGMII/8xSGMII riser card with eighth SerDes
+interfaces implemented in PCIe form factor board.
+It supports followings
+ - Card can operate with up to 4 QSGMII lane simultaneously
+ - Card can operate with up to 8 SGMII lane simultaneously
+
+Supported card configuration
+ - CSEL : ON ON ON ON
+ - MSEL1 : ON ON ON ON OFF OFF OFF OFF
+ - MSEL2 : OFF OFF OFF OFF ON ON ON ON
+
+To enable this card: modify hwconfig to add "xqsgmii" variable.
+
+Supported PHY addresses during SGMII:
+#define XQSGMII_CARD_PHY1_PORT0_ADDR 0x0
+#define XQSGMII_CARD_PHY1_PORT2_ADDR 0x2
+#define XQSGMII_CARD_PHY2_PORT0_ADDR 0x4
+#define XQSGMII_CARD_PHY2_PORT2_ADDR 0x6
+#define XQSGMII_CARD_PHY3_PORT0_ADDR 0x8
+#define XQSGMII_CARD_PHY3_PORT2_ADDR 0xa
+#define XQSGMII_CARD_PHY4_PORT0_ADDR 0xc
+#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
+
+Mapping DPMACx to PHY during QSGMII
+DPMAC1 -> PHY1-P0
+DPMAC2 -> PHY2-P0
+DPMAC3 -> PHY3-P0
+DPMAC4 -> PHY4-P0
+DPMAC5 -> PHY3-P2
+DPMAC6 -> PHY1-P2
+DPMAC7 -> PHY4-P1
+DPMAC8 -> PHY2-P2
+DPMAC9 -> PHY1-P0
+DPMAC10 -> PHY2-P0
+DPMAC11 -> PHY3-P0
+DPMAC12 -> PHY4-P0
+DPMAC13 -> PHY3-P2
+DPMAC14 -> PHY1-P2
+DPMAC15 -> PHY4-P1
+DPMAC16 -> PHY2-P2
+
+
+Supported PHY address during QSGMII
+#define XQSGMII_CARD_PHY1_PORT0_ADDR 0x0
+#define XQSGMII_CARD_PHY1_PORT1_ADDR 0x1
+#define XQSGMII_CARD_PHY1_PORT2_ADDR 0x2
+#define XQSGMII_CARD_PHY1_PORT3_ADDR 0x3
+#define XQSGMII_CARD_PHY2_PORT0_ADDR 0x4
+#define XQSGMII_CARD_PHY2_PORT1_ADDR 0x5
+#define XQSGMII_CARD_PHY2_PORT2_ADDR 0x6
+#define XQSGMII_CARD_PHY2_PORT3_ADDR 0x7
+#define XQSGMII_CARD_PHY3_PORT0_ADDR 0x8
+#define XQSGMII_CARD_PHY3_PORT1_ADDR 0x9
+#define XQSGMII_CARD_PHY3_PORT2_ADDR 0xa
+#define XQSGMII_CARD_PHY3_PORT3_ADDR 0xb
+#define XQSGMII_CARD_PHY4_PORT0_ADDR 0xc
+#define XQSGMII_CARD_PHY4_PORT1_ADDR 0xd
+#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
+#define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf
+
+Mapping DPMACx to PHY during QSGMII
+DPMAC1 -> PHY1-P3
+DPMAC2 -> PHY1-P2
+DPMAC3 -> PHY1-P1
+DPMAC4 -> PHY1-P0
+DPMAC5 -> PHY2-P3
+DPMAC6 -> PHY2-P2
+DPMAC7 -> PHY2-P1
+DPMAC8 -> PHY2-P0
+DPMAC9 -> PHY3-P0
+DPMAC10 -> PHY3-P1
+DPMAC11 -> PHY3-P2
+DPMAC12 -> PHY3-P3
+DPMAC13 -> PHY4-P0
+DPMAC14 -> PHY4-P1
+DPMAC15 -> PHY4-P2
+DPMAC16 -> PHY4-P3
+
diff --git a/board/freescale/ls2085aqds/eth.c b/board/freescale/ls2085aqds/eth.c
index 1f8a31f..007b433 100644
--- a/board/freescale/ls2085aqds/eth.c
+++ b/board/freescale/ls2085aqds/eth.c
@@ -9,9 +9,12 @@
#include <asm/io.h>
#include <asm/arch/fsl_serdes.h>
#include <asm/arch-fsl-lsch3/immap_lsch3.h>
+#include <hwconfig.h>
#include <fsl_mdio.h>
#include <malloc.h>
#include <fm_eth.h>
+#include <i2c.h>
+#include <miiphy.h>
#include <fsl-mc/ldpaa_wriop.h>
#include "../common/qixis.h"
@@ -30,6 +33,10 @@
* maps to something other than a board slot.
*/
+static u8 lane_to_slot_fsm1[] = {
+ 0, 0, 0, 0, 0, 0, 0, 0
+};
+
static u8 lane_to_slot_fsm2[] = {
0, 0, 0, 0, 0, 0, 0, 0
};
@@ -37,7 +44,19 @@ static u8 lane_to_slot_fsm2[] = {
/* On the Vitesse VSC8234XHG SGMII riser card there are 4 SGMII PHYs
* housed.
*/
-static int riser_phy_addr[] = {
+
+static int xqsgii_riser_phy_addr[] = {
+ XQSGMII_CARD_PHY1_PORT0_ADDR,
+ XQSGMII_CARD_PHY2_PORT0_ADDR,
+ XQSGMII_CARD_PHY3_PORT0_ADDR,
+ XQSGMII_CARD_PHY4_PORT0_ADDR,
+ XQSGMII_CARD_PHY3_PORT2_ADDR,
+ XQSGMII_CARD_PHY1_PORT2_ADDR,
+ XQSGMII_CARD_PHY4_PORT2_ADDR,
+ XQSGMII_CARD_PHY2_PORT2_ADDR,
+};
+
+static int sgmii_riser_phy_addr[] = {
SGMII_CARD_PORT1_PHY_ADDR,
SGMII_CARD_PORT2_PHY_ADDR,
SGMII_CARD_PORT3_PHY_ADDR,
@@ -70,6 +89,236 @@ struct ls2085a_qds_mdio {
struct mii_dev *realbus;
};
+static void sgmii_configure_repeater(int serdes_port)
+{
+ struct mii_dev *bus;
+ uint8_t a = 0xf;
+ int i, j, ret;
+ int dpmac_id = 0, dpmac, mii_bus = 0;
+ unsigned short value;
+ char dev[2][20] = {"LS2085A_QDS_MDIO0", "LS2085A_QDS_MDIO3"};
+ uint8_t i2c_addr[] = {0x58, 0x59, 0x5a, 0x5b, 0x5c, 0x5d, 0x5f, 0x60};
+
+ uint8_t ch_a_eq[] = {0x1, 0x2, 0x3, 0x7};
+ uint8_t ch_a_ctl2[] = {0x81, 0x82, 0x83, 0x84};
+ uint8_t ch_b_eq[] = {0x1, 0x2, 0x3, 0x7};
+ uint8_t ch_b_ctl2[] = {0x81, 0x82, 0x83, 0x84};
+
+ int *riser_phy_addr = &xqsgii_riser_phy_addr[0];
+
+ /* Set I2c to Slot 1 */
+ i2c_write(0x77, 0, 0, &a, 1);
+
+ for (dpmac = 0; dpmac < 8; dpmac++) {
+ /* Check the PHY status */
+ switch (serdes_port) {
+ case 1:
+ mii_bus = 0;
+ dpmac_id = dpmac + 1;
+ break;
+ case 2:
+ mii_bus = 1;
+ dpmac_id = dpmac + 9;
+ a = 0xb;
+ i2c_write(0x76, 0, 0, &a, 1);
+ break;
+ }
+
+ ret = miiphy_set_current_dev(dev[mii_bus]);
+ if (ret > 0)
+ goto error;
+
+ bus = mdio_get_current_dev();
+ debug("Reading from bus %s\n", bus->name);
+
+ ret = miiphy_write(dev[mii_bus], riser_phy_addr[dpmac], 0x1f,
+ 3);
+ if (ret > 0)
+ goto error;
+
+ mdelay(10);
+ ret = miiphy_read(dev[mii_bus], riser_phy_addr[dpmac], 0x11,
+ &value);
+ if (ret > 0)
+ goto error;
+
+ mdelay(10);
+
+ if ((value & 0xfff) == 0x40f) {
+ printf("DPMAC %d:PHY is ..... Configured\n", dpmac_id);
+ continue;
+ }
+
+ for (i = 0; i < 4; i++) {
+ for (j = 0; j < 4; j++) {
+ a = 0x18;
+ i2c_write(i2c_addr[dpmac], 6, 1, &a, 1);
+ a = 0x38;
+ i2c_write(i2c_addr[dpmac], 4, 1, &a, 1);
+ a = 0x4;
+ i2c_write(i2c_addr[dpmac], 8, 1, &a, 1);
+
+ i2c_write(i2c_addr[dpmac], 0xf, 1,
+ &ch_a_eq[i], 1);
+ i2c_write(i2c_addr[dpmac], 0x11, 1,
+ &ch_a_ctl2[j], 1);
+
+ i2c_write(i2c_addr[dpmac], 0x16, 1,
+ &ch_b_eq[i], 1);
+ i2c_write(i2c_addr[dpmac], 0x18, 1,
+ &ch_b_ctl2[j], 1);
+
+ a = 0x14;
+ i2c_write(i2c_addr[dpmac], 0x23, 1, &a, 1);
+ a = 0xb5;
+ i2c_write(i2c_addr[dpmac], 0x2d, 1, &a, 1);
+ a = 0x20;
+ i2c_write(i2c_addr[dpmac], 4, 1, &a, 1);
+ mdelay(100);
+ ret = miiphy_read(dev[mii_bus],
+ riser_phy_addr[dpmac],
+ 0x11, &value);
+ if (ret > 0)
+ goto error;
+
+ mdelay(1);
+ ret = miiphy_read(dev[mii_bus],
+ riser_phy_addr[dpmac],
+ 0x11, &value);
+ if (ret > 0)
+ goto error;
+ mdelay(10);
+
+ if ((value & 0xfff) == 0x40f) {
+ printf("DPMAC %d :PHY is configured ",
+ dpmac_id);
+ printf("after setting repeater 0x%x\n",
+ value);
+ i = 5;
+ j = 5;
+ } else
+ printf("DPMAC %d :PHY is failed to ",
+ dpmac_id);
+ printf("configure the repeater 0x%x\n",
+ value);
+ }
+ }
+ }
+error:
+ if (ret)
+ printf("DPMAC %d ..... FAILED to configure PHY\n", dpmac_id);
+ return;
+}
+
+static void qsgmii_configure_repeater(int dpmac)
+{
+ uint8_t a = 0xf;
+ int i, j;
+ int i2c_phy_addr = 0;
+ int phy_addr = 0;
+ int i2c_addr[] = {0x58, 0x59, 0x5a, 0x5b};
+
+ uint8_t ch_a_eq[] = {0x1, 0x2, 0x3, 0x7};
+ uint8_t ch_a_ctl2[] = {0x81, 0x82, 0x83, 0x84};
+ uint8_t ch_b_eq[] = {0x1, 0x2, 0x3, 0x7};
+ uint8_t ch_b_ctl2[] = {0x81, 0x82, 0x83, 0x84};
+
+ const char *dev = "LS2085A_QDS_MDIO0";
+ int ret = 0;
+ unsigned short value;
+
+ /* Set I2c to Slot 1 */
+ i2c_write(0x77, 0, 0, &a, 1);
+
+ switch (dpmac) {
+ case 1:
+ case 2:
+ case 3:
+ case 4:
+ i2c_phy_addr = i2c_addr[0];
+ phy_addr = 0;
+ break;
+
+ case 5:
+ case 6:
+ case 7:
+ case 8:
+ i2c_phy_addr = i2c_addr[1];
+ phy_addr = 4;
+ break;
+
+ case 9:
+ case 10:
+ case 11:
+ case 12:
+ i2c_phy_addr = i2c_addr[2];
+ phy_addr = 8;
+ break;
+
+ case 13:
+ case 14:
+ case 15:
+ case 16:
+ i2c_phy_addr = i2c_addr[3];
+ phy_addr = 0xc;
+ break;
+ }
+
+ /* Check the PHY status */
+ ret = miiphy_set_current_dev(dev);
+ ret = miiphy_write(dev, phy_addr, 0x1f, 3);
+ mdelay(10);
+ ret = miiphy_read(dev, phy_addr, 0x11, &value);
+ mdelay(10);
+ ret = miiphy_read(dev, phy_addr, 0x11, &value);
+ mdelay(10);
+ if ((value & 0xf) == 0xf) {
+ printf("DPMAC %d :PHY is ..... Configured\n", dpmac);
+ return;
+ }
+
+ for (i = 0; i < 4; i++) {
+ for (j = 0; j < 4; j++) {
+ a = 0x18;
+ i2c_write(i2c_phy_addr, 6, 1, &a, 1);
+ a = 0x38;
+ i2c_write(i2c_phy_addr, 4, 1, &a, 1);
+ a = 0x4;
+ i2c_write(i2c_phy_addr, 8, 1, &a, 1);
+
+ i2c_write(i2c_phy_addr, 0xf, 1, &ch_a_eq[i], 1);
+ i2c_write(i2c_phy_addr, 0x11, 1, &ch_a_ctl2[j], 1);
+
+ i2c_write(i2c_phy_addr, 0x16, 1, &ch_b_eq[i], 1);
+ i2c_write(i2c_phy_addr, 0x18, 1, &ch_b_ctl2[j], 1);
+
+ a = 0x14;
+ i2c_write(i2c_phy_addr, 0x23, 1, &a, 1);
+ a = 0xb5;
+ i2c_write(i2c_phy_addr, 0x2d, 1, &a, 1);
+ a = 0x20;
+ i2c_write(i2c_phy_addr, 4, 1, &a, 1);
+ mdelay(100);
+ ret = miiphy_read(dev, phy_addr, 0x11, &value);
+ if (ret > 0)
+ goto error;
+ mdelay(1);
+ ret = miiphy_read(dev, phy_addr, 0x11, &value);
+ if (ret > 0)
+ goto error;
+ mdelay(10);
+ if ((value & 0xf) == 0xf) {
+ printf("DPMAC %d :PHY is ..... Configured\n",
+ dpmac);
+ return;
+ }
+ }
+ }
+error:
+ printf("DPMAC %d :PHY ..... FAILED to configure PHY\n", dpmac);
+ return;
+}
+
static const char *ls2085a_qds_mdio_name_for_muxval(u8 muxval)
{
return mdio_names[muxval];
@@ -195,14 +444,38 @@ static void initialize_dpmac_to_slot(void)
FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_MASK)
>> FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_SHIFT;
+ char *env_hwconfig;
+ env_hwconfig = getenv("hwconfig");
switch (serdes1_prtcl) {
+ case 0x07:
+ case 0x09:
+ case 0x33:
+ printf("qds: WRIOP: Supported SerDes1 Protocol 0x%02x\n",
+ serdes1_prtcl);
+ lane_to_slot_fsm1[0] = EMI1_SLOT1;
+ lane_to_slot_fsm1[1] = EMI1_SLOT1;
+ lane_to_slot_fsm1[2] = EMI1_SLOT1;
+ lane_to_slot_fsm1[3] = EMI1_SLOT1;
+ if (hwconfig_f("xqsgmii", env_hwconfig)) {
+ lane_to_slot_fsm1[4] = EMI1_SLOT1;
+ lane_to_slot_fsm1[5] = EMI1_SLOT1;
+ lane_to_slot_fsm1[6] = EMI1_SLOT1;
+ lane_to_slot_fsm1[7] = EMI1_SLOT1;
+ } else {
+ lane_to_slot_fsm1[4] = EMI1_SLOT2;
+ lane_to_slot_fsm1[5] = EMI1_SLOT2;
+ lane_to_slot_fsm1[6] = EMI1_SLOT2;
+ lane_to_slot_fsm1[7] = EMI1_SLOT2;
+ }
+ break;
+
case 0x2A:
- printf("qds: WRIOP: Supported SerDes Protocol 0x%02x\n",
+ printf("qds: WRIOP: Supported SerDes1 Protocol 0x%02x\n",
serdes1_prtcl);
break;
default:
- printf("qds: WRIOP: Unsupported SerDes Protocol 0x%02x\n",
+ printf("qds: WRIOP: Unsupported SerDes1 Protocol 0x%02x\n",
serdes1_prtcl);
break;
}
@@ -210,21 +483,30 @@ static void initialize_dpmac_to_slot(void)
switch (serdes2_prtcl) {
case 0x07:
case 0x08:
+ case 0x09:
case 0x49:
- printf("qds: WRIOP: Supported SerDes Protocol 0x%02x\n",
+ printf("qds: WRIOP: Supported SerDes2 Protocol 0x%02x\n",
serdes2_prtcl);
lane_to_slot_fsm2[0] = EMI1_SLOT4;
lane_to_slot_fsm2[1] = EMI1_SLOT4;
lane_to_slot_fsm2[2] = EMI1_SLOT4;
lane_to_slot_fsm2[3] = EMI1_SLOT4;
- /* No MDIO physical connection */
- lane_to_slot_fsm2[4] = EMI1_SLOT6;
- lane_to_slot_fsm2[5] = EMI1_SLOT6;
- lane_to_slot_fsm2[6] = EMI1_SLOT6;
- lane_to_slot_fsm2[7] = EMI1_SLOT6;
+
+ if (hwconfig_f("xqsgmii", env_hwconfig)) {
+ lane_to_slot_fsm2[4] = EMI1_SLOT4;
+ lane_to_slot_fsm2[5] = EMI1_SLOT4;
+ lane_to_slot_fsm2[6] = EMI1_SLOT4;
+ lane_to_slot_fsm2[7] = EMI1_SLOT4;
+ } else {
+ /* No MDIO physical connection */
+ lane_to_slot_fsm2[4] = EMI1_SLOT6;
+ lane_to_slot_fsm2[5] = EMI1_SLOT6;
+ lane_to_slot_fsm2[6] = EMI1_SLOT6;
+ lane_to_slot_fsm2[7] = EMI1_SLOT6;
+ }
break;
default:
- printf("qds: WRIOP: Unsupported SerDes Protocol 0x%02x\n",
+ printf("qds: WRIOP: Unsupported SerDes2 Protocol 0x%02x\n",
serdes2_prtcl);
break;
}
@@ -242,9 +524,69 @@ void ls2085a_handle_phy_interface_sgmii(int dpmac_id)
FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_MASK)
>> FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_SHIFT;
+ int *riser_phy_addr;
+ char *env_hwconfig = getenv("hwconfig");
+
+ if (hwconfig_f("xqsgmii", env_hwconfig))
+ riser_phy_addr = &xqsgii_riser_phy_addr[0];
+ else
+ riser_phy_addr = &sgmii_riser_phy_addr[0];
+
+ if (dpmac_id > WRIOP1_DPMAC9)
+ goto serdes2;
+
switch (serdes1_prtcl) {
+ case 0x07:
+
+ lane = serdes_get_first_lane(FSL_SRDS_1, SGMII1 + dpmac_id);
+ slot = lane_to_slot_fsm1[lane];
+
+ switch (++slot) {
+ case 1:
+ /* Slot housing a SGMII riser card? */
+ wriop_set_phy_address(dpmac_id,
+ riser_phy_addr[dpmac_id - 1]);
+ dpmac_info[dpmac_id].board_mux = EMI1_SLOT1;
+ bus = mii_dev_for_muxval(EMI1_SLOT1);
+ wriop_set_mdio(dpmac_id, bus);
+ dpmac_info[dpmac_id].phydev = phy_connect(
+ dpmac_info[dpmac_id].bus,
+ dpmac_info[dpmac_id].phy_addr,
+ NULL,
+ dpmac_info[dpmac_id].enet_if);
+ phy_config(dpmac_info[dpmac_id].phydev);
+ break;
+ case 2:
+ /* Slot housing a SGMII riser card? */
+ wriop_set_phy_address(dpmac_id,
+ riser_phy_addr[dpmac_id - 1]);
+ dpmac_info[dpmac_id].board_mux = EMI1_SLOT2;
+ bus = mii_dev_for_muxval(EMI1_SLOT2);
+ wriop_set_mdio(dpmac_id, bus);
+ dpmac_info[dpmac_id].phydev = phy_connect(
+ dpmac_info[dpmac_id].bus,
+ dpmac_info[dpmac_id].phy_addr,
+ NULL,
+ dpmac_info[dpmac_id].enet_if);
+ phy_config(dpmac_info[dpmac_id].phydev);
+ break;
+ case 3:
+ break;
+ case 4:
+ break;
+ case 5:
+ break;
+ case 6:
+ break;
+ }
+ break;
+ default:
+ printf("qds: WRIOP: Unsupported SerDes1 Protocol 0x%02x\n",
+ serdes1_prtcl);
+ break;
}
+serdes2:
switch (serdes2_prtcl) {
case 0x07:
case 0x08:
@@ -285,11 +627,86 @@ void ls2085a_handle_phy_interface_sgmii(int dpmac_id)
}
break;
default:
- printf("qds: WRIOP: Unsupported SerDes Protocol 0x%02x\n",
+ printf("qds: WRIOP: Unsupported SerDes2 Protocol 0x%02x\n",
serdes2_prtcl);
break;
}
}
+
+void ls2085a_handle_phy_interface_qsgmii(int dpmac_id)
+{
+ int lane = 0, slot;
+ struct mii_dev *bus;
+ struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+ int serdes1_prtcl = (in_le32(&gur->rcwsr[28]) &
+ FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK)
+ >> FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT;
+
+ switch (serdes1_prtcl) {
+ case 0x33:
+ switch (dpmac_id) {
+ case 1:
+ case 2:
+ case 3:
+ case 4:
+ lane = serdes_get_first_lane(FSL_SRDS_1, QSGMII_A);
+ break;
+ case 5:
+ case 6:
+ case 7:
+ case 8:
+ lane = serdes_get_first_lane(FSL_SRDS_1, QSGMII_B);
+ break;
+ case 9:
+ case 10:
+ case 11:
+ case 12:
+ lane = serdes_get_first_lane(FSL_SRDS_1, QSGMII_C);
+ break;
+ case 13:
+ case 14:
+ case 15:
+ case 16:
+ lane = serdes_get_first_lane(FSL_SRDS_1, QSGMII_D);
+ break;
+ }
+
+ slot = lane_to_slot_fsm1[lane];
+
+ switch (++slot) {
+ case 1:
+ /* Slot housing a QSGMII riser card? */
+ wriop_set_phy_address(dpmac_id, dpmac_id - 1);
+ dpmac_info[dpmac_id].board_mux = EMI1_SLOT1;
+ bus = mii_dev_for_muxval(EMI1_SLOT1);
+ wriop_set_mdio(dpmac_id, bus);
+ dpmac_info[dpmac_id].phydev = phy_connect(
+ dpmac_info[dpmac_id].bus,
+ dpmac_info[dpmac_id].phy_addr,
+ NULL,
+ dpmac_info[dpmac_id].enet_if);
+
+ phy_config(dpmac_info[dpmac_id].phydev);
+ break;
+ case 3:
+ break;
+ case 4:
+ break;
+ case 5:
+ break;
+ case 6:
+ break;
+ }
+ break;
+ default:
+ printf("qds: WRIOP: Unsupported SerDes Protocol 0x%02x\n",
+ serdes1_prtcl);
+ break;
+ }
+
+ qsgmii_configure_repeater(dpmac_id);
+}
+
void ls2085a_handle_phy_interface_xsgmii(int i)
{
struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
@@ -324,9 +741,20 @@ int board_eth_init(bd_t *bis)
{
int error;
#ifdef CONFIG_FSL_MC_ENET
+ struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+ int serdes1_prtcl = (in_le32(&gur->rcwsr[28]) &
+ FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK)
+ >> FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT;
+ int serdes2_prtcl = (in_le32(&gur->rcwsr[28]) &
+ FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_MASK)
+ >> FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_SHIFT;
+
struct memac_mdio_info *memac_mdio0_info;
struct memac_mdio_info *memac_mdio1_info;
unsigned int i;
+ char *env_hwconfig;
+
+ env_hwconfig = getenv("hwconfig");
initialize_dpmac_to_slot();
@@ -363,6 +791,7 @@ int board_eth_init(bd_t *bis)
for (i = WRIOP1_DPMAC1; i < NUM_WRIOP_PORTS; i++) {
switch (wriop_get_enet_if(i)) {
case PHY_INTERFACE_MODE_QSGMII:
+ ls2085a_handle_phy_interface_qsgmii(i);
break;
case PHY_INTERFACE_MODE_SGMII:
ls2085a_handle_phy_interface_sgmii(i);
@@ -372,11 +801,26 @@ int board_eth_init(bd_t *bis)
break;
default:
break;
+
+ if (i == 16)
+ i = NUM_WRIOP_PORTS;
}
}
error = cpu_eth_init(bis);
+
+ if (hwconfig_f("xqsgmii", env_hwconfig)) {
+ if (serdes1_prtcl == 0x7)
+ sgmii_configure_repeater(1);
+ if (serdes2_prtcl == 0x7 || serdes2_prtcl == 0x8 ||
+ serdes2_prtcl == 0x49)
+ sgmii_configure_repeater(2);
+ }
#endif
error = pci_eth_init(bis);
return error;
}
+
+#ifdef CONFIG_FSL_MC_ENET
+
+#endif
diff --git a/include/configs/ls2085aqds.h b/include/configs/ls2085aqds.h
index f380ecc..5903aee 100644
--- a/include/configs/ls2085aqds.h
+++ b/include/configs/ls2085aqds.h
@@ -396,6 +396,23 @@ unsigned long get_board_ddr_clk(void);
#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
+#define XQSGMII_CARD_PHY1_PORT0_ADDR 0x0
+#define XQSGMII_CARD_PHY1_PORT1_ADDR 0x1
+#define XQSGMII_CARD_PHY1_PORT2_ADDR 0x2
+#define XQSGMII_CARD_PHY1_PORT3_ADDR 0x3
+#define XQSGMII_CARD_PHY2_PORT0_ADDR 0x4
+#define XQSGMII_CARD_PHY2_PORT1_ADDR 0x5
+#define XQSGMII_CARD_PHY2_PORT2_ADDR 0x6
+#define XQSGMII_CARD_PHY2_PORT3_ADDR 0x7
+#define XQSGMII_CARD_PHY3_PORT0_ADDR 0x8
+#define XQSGMII_CARD_PHY3_PORT1_ADDR 0x9
+#define XQSGMII_CARD_PHY3_PORT2_ADDR 0xa
+#define XQSGMII_CARD_PHY3_PORT3_ADDR 0xb
+#define XQSGMII_CARD_PHY4_PORT0_ADDR 0xc
+#define XQSGMII_CARD_PHY4_PORT1_ADDR 0xd
+#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
+#define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf
+
#define CONFIG_MII /* MII PHY management */
#define CONFIG_ETHPRIME "DPNI1"
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
--
1.9.1
More information about the U-Boot
mailing list