[U-Boot] [PATCH v3 3/4] usb: gadget: at91_udc: add at91_udc into U-Boot
Heiko Schocher
hs at denx.de
Wed Aug 12 09:31:36 CEST 2015
add U-Boot specific changes to the at91_udc linux driver,
so it works with U-Boot.
Signed-off-by: Heiko Schocher <hs at denx.de>
---
Changes in v3:
- adapt changes for U-Boot, as newer linux version is
used.
Changes in v2:
- new in version 2, contains U-Boot changes
drivers/usb/gadget/Makefile | 1 +
drivers/usb/gadget/at91_udc.c | 601 +++++++-----------------------------------
drivers/usb/gadget/at91_udc.h | 16 +-
include/linux/usb/at91_udc.h | 20 ++
4 files changed, 122 insertions(+), 516 deletions(-)
create mode 100644 include/linux/usb/at91_udc.h
diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile
index 4c11a7e..6288ecf 100644
--- a/drivers/usb/gadget/Makefile
+++ b/drivers/usb/gadget/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_USB_ETHER) += epautoconf.o config.o usbstring.o
# new USB gadget layer dependencies
ifdef CONFIG_USB_GADGET
+obj-$(CONFIG_USB_GADGET_AT91) += at91_udc.o
obj-$(CONFIG_USB_GADGET_ATMEL_USBA) += atmel_usba_udc.o
obj-$(CONFIG_USB_GADGET_BCM_UDC_OTG_PHY) += bcm_udc_otg_phy.o
obj-$(CONFIG_USB_GADGET_S3C_UDC_OTG) += s3c_udc_otg.o
diff --git a/drivers/usb/gadget/at91_udc.c b/drivers/usb/gadget/at91_udc.c
index fc42264..3c3553a 100644
--- a/drivers/usb/gadget/at91_udc.c
+++ b/drivers/usb/gadget/at91_udc.c
@@ -1,43 +1,34 @@
/*
+ * from linux:
+ * c94e289f195e: usb: gadget: remove incorrect __init/__exit annotations
+ *
* at91_udc -- driver for at91-series USB peripheral controller
*
* Copyright (C) 2004 by Thomas Rathbone
* Copyright (C) 2005 by HP Labs
* Copyright (C) 2005 by David Brownell
*
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
+ * SPDX-License-Identifier: GPL-2.0+
*/
#undef VERBOSE_DEBUG
#undef PACKET_TRACE
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-#include <linux/errno.h>
+#include <common.h>
+#include <asm/errno.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <asm/hardware.h>
+#include <mach/at91_matrix.h>
#include <linux/list.h>
-#include <linux/interrupt.h>
-#include <linux/proc_fs.h>
-#include <linux/prefetch.h>
-#include <linux/clk.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
-#include <linux/of.h>
-#include <linux/of_gpio.h>
-#include <linux/platform_data/atmel.h>
-#include <linux/regmap.h>
-#include <linux/mfd/syscon.h>
-#include <linux/mfd/syscon/atmel-matrix.h>
+#include <linux/usb/at91_udc.h>
+#include <malloc.h>
+#include <usb/lin_gadget_compat.h>
#include "at91_udc.h"
-
/*
* This controller is simple and PIO-only. It's used in many AT91-series
* full speed USB controllers, including the at91rm9200 (arm920T, with MMU),
@@ -69,187 +60,12 @@ static const char * const ep_names[] = {
};
#define ep0name ep_names[0]
-#define VBUS_POLL_TIMEOUT msecs_to_jiffies(1000)
-
#define at91_udp_read(udc, reg) \
__raw_readl((udc)->udp_baseaddr + (reg))
#define at91_udp_write(udc, reg, val) \
__raw_writel((val), (udc)->udp_baseaddr + (reg))
-/*-------------------------------------------------------------------------*/
-
-#ifdef CONFIG_USB_GADGET_DEBUG_FILES
-
-#include <linux/seq_file.h>
-
-static const char debug_filename[] = "driver/udc";
-
-#define FOURBITS "%s%s%s%s"
-#define EIGHTBITS FOURBITS FOURBITS
-
-static void proc_ep_show(struct seq_file *s, struct at91_ep *ep)
-{
- static char *types[] = {
- "control", "out-iso", "out-bulk", "out-int",
- "BOGUS", "in-iso", "in-bulk", "in-int"};
-
- u32 csr;
- struct at91_request *req;
- unsigned long flags;
- struct at91_udc *udc = ep->udc;
-
- spin_lock_irqsave(&udc->lock, flags);
-
- csr = __raw_readl(ep->creg);
-
- /* NOTE: not collecting per-endpoint irq statistics... */
-
- seq_printf(s, "\n");
- seq_printf(s, "%s, maxpacket %d %s%s %s%s\n",
- ep->ep.name, ep->ep.maxpacket,
- ep->is_in ? "in" : "out",
- ep->is_iso ? " iso" : "",
- ep->is_pingpong
- ? (ep->fifo_bank ? "pong" : "ping")
- : "",
- ep->stopped ? " stopped" : "");
- seq_printf(s, "csr %08x rxbytes=%d %s %s %s" EIGHTBITS "\n",
- csr,
- (csr & 0x07ff0000) >> 16,
- (csr & (1 << 15)) ? "enabled" : "disabled",
- (csr & (1 << 11)) ? "DATA1" : "DATA0",
- types[(csr & 0x700) >> 8],
-
- /* iff type is control then print current direction */
- (!(csr & 0x700))
- ? ((csr & (1 << 7)) ? " IN" : " OUT")
- : "",
- (csr & (1 << 6)) ? " rxdatabk1" : "",
- (csr & (1 << 5)) ? " forcestall" : "",
- (csr & (1 << 4)) ? " txpktrdy" : "",
-
- (csr & (1 << 3)) ? " stallsent" : "",
- (csr & (1 << 2)) ? " rxsetup" : "",
- (csr & (1 << 1)) ? " rxdatabk0" : "",
- (csr & (1 << 0)) ? " txcomp" : "");
- if (list_empty (&ep->queue))
- seq_printf(s, "\t(queue empty)\n");
-
- else list_for_each_entry (req, &ep->queue, queue) {
- unsigned length = req->req.actual;
-
- seq_printf(s, "\treq %p len %d/%d buf %p\n",
- &req->req, length,
- req->req.length, req->req.buf);
- }
- spin_unlock_irqrestore(&udc->lock, flags);
-}
-
-static void proc_irq_show(struct seq_file *s, const char *label, u32 mask)
-{
- int i;
-
- seq_printf(s, "%s %04x:%s%s" FOURBITS, label, mask,
- (mask & (1 << 13)) ? " wakeup" : "",
- (mask & (1 << 12)) ? " endbusres" : "",
-
- (mask & (1 << 11)) ? " sofint" : "",
- (mask & (1 << 10)) ? " extrsm" : "",
- (mask & (1 << 9)) ? " rxrsm" : "",
- (mask & (1 << 8)) ? " rxsusp" : "");
- for (i = 0; i < 8; i++) {
- if (mask & (1 << i))
- seq_printf(s, " ep%d", i);
- }
- seq_printf(s, "\n");
-}
-
-static int proc_udc_show(struct seq_file *s, void *unused)
-{
- struct at91_udc *udc = s->private;
- struct at91_ep *ep;
- u32 tmp;
-
- seq_printf(s, "%s: version %s\n", driver_name, DRIVER_VERSION);
-
- seq_printf(s, "vbus %s, pullup %s, %s powered%s, gadget %s\n\n",
- udc->vbus ? "present" : "off",
- udc->enabled
- ? (udc->vbus ? "active" : "enabled")
- : "disabled",
- udc->gadget.is_selfpowered ? "self" : "VBUS",
- udc->suspended ? ", suspended" : "",
- udc->driver ? udc->driver->driver.name : "(none)");
-
- /* don't access registers when interface isn't clocked */
- if (!udc->clocked) {
- seq_printf(s, "(not clocked)\n");
- return 0;
- }
-
- tmp = at91_udp_read(udc, AT91_UDP_FRM_NUM);
- seq_printf(s, "frame %05x:%s%s frame=%d\n", tmp,
- (tmp & AT91_UDP_FRM_OK) ? " ok" : "",
- (tmp & AT91_UDP_FRM_ERR) ? " err" : "",
- (tmp & AT91_UDP_NUM));
-
- tmp = at91_udp_read(udc, AT91_UDP_GLB_STAT);
- seq_printf(s, "glbstate %02x:%s" FOURBITS "\n", tmp,
- (tmp & AT91_UDP_RMWUPE) ? " rmwupe" : "",
- (tmp & AT91_UDP_RSMINPR) ? " rsminpr" : "",
- (tmp & AT91_UDP_ESR) ? " esr" : "",
- (tmp & AT91_UDP_CONFG) ? " confg" : "",
- (tmp & AT91_UDP_FADDEN) ? " fadden" : "");
-
- tmp = at91_udp_read(udc, AT91_UDP_FADDR);
- seq_printf(s, "faddr %03x:%s fadd=%d\n", tmp,
- (tmp & AT91_UDP_FEN) ? " fen" : "",
- (tmp & AT91_UDP_FADD));
-
- proc_irq_show(s, "imr ", at91_udp_read(udc, AT91_UDP_IMR));
- proc_irq_show(s, "isr ", at91_udp_read(udc, AT91_UDP_ISR));
-
- if (udc->enabled && udc->vbus) {
- proc_ep_show(s, &udc->ep[0]);
- list_for_each_entry (ep, &udc->gadget.ep_list, ep.ep_list) {
- if (ep->ep.desc)
- proc_ep_show(s, ep);
- }
- }
- return 0;
-}
-
-static int proc_udc_open(struct inode *inode, struct file *file)
-{
- return single_open(file, proc_udc_show, PDE_DATA(inode));
-}
-
-static const struct file_operations proc_ops = {
- .owner = THIS_MODULE,
- .open = proc_udc_open,
- .read = seq_read,
- .llseek = seq_lseek,
- .release = single_release,
-};
-
-static void create_debug_file(struct at91_udc *udc)
-{
- udc->pde = proc_create_data(debug_filename, 0, NULL, &proc_ops, udc);
-}
-
-static void remove_debug_file(struct at91_udc *udc)
-{
- if (udc->pde)
- remove_proc_entry(debug_filename, NULL);
-}
-
-#else
-
-static inline void create_debug_file(struct at91_udc *udc) {}
-static inline void remove_debug_file(struct at91_udc *udc) {}
-
-#endif
-
+static struct at91_udc *controller;
/*-------------------------------------------------------------------------*/
@@ -268,7 +84,7 @@ static void done(struct at91_ep *ep, struct at91_request *req, int status)
ep->stopped = 1;
spin_unlock(&udc->lock);
- usb_gadget_giveback_request(&ep->ep, &req->req);
+ req->req.complete(&ep->ep, &req->req);
spin_lock(&udc->lock);
ep->stopped = stopped;
@@ -332,7 +148,7 @@ rescan:
req->req.status = -EOVERFLOW;
count = bufferspace;
}
- __raw_readsb(dreg, buf, count);
+ __raw_readsb((unsigned long)dreg, buf, count);
/* release and swap pingpong mem bank */
csr |= CLR_FX;
@@ -434,7 +250,7 @@ static int write_fifo(struct at91_ep *ep, struct at91_request *req)
* recover when the actual bytecount matters (e.g. for USB Test
* and Measurement Class devices).
*/
- __raw_writesb(dreg, buf, count);
+ __raw_writesb((unsigned long)dreg, buf, count);
csr &= ~SET_FX;
csr |= CLR_FX | AT91_UDP_TXPKTRDY;
__raw_writel(csr, creg);
@@ -703,14 +519,11 @@ static int at91_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req)
struct at91_ep *ep;
struct at91_request *req;
unsigned long flags;
- struct at91_udc *udc;
ep = container_of(_ep, struct at91_ep, ep);
if (!_ep || ep->ep.name == ep0name)
return -EINVAL;
- udc = ep->udc;
-
spin_lock_irqsave(&udc->lock, flags);
/* make sure it's actually queued on this endpoint */
@@ -859,7 +672,7 @@ static void reset_gadget(struct at91_udc *udc)
}
if (driver) {
spin_unlock(&udc->lock);
- usb_gadget_udc_reset(&udc->gadget, driver);
+ udc->driver->disconnect(&udc->gadget);
spin_lock(&udc->lock);
}
@@ -895,9 +708,6 @@ static void clk_on(struct at91_udc *udc)
if (udc->clocked)
return;
udc->clocked = 1;
-
- clk_enable(udc->iclk);
- clk_enable(udc->fclk);
}
static void clk_off(struct at91_udc *udc)
@@ -906,8 +716,6 @@ static void clk_off(struct at91_udc *udc)
return;
udc->clocked = 0;
udc->gadget.speed = USB_SPEED_UNKNOWN;
- clk_disable(udc->fclk);
- clk_disable(udc->iclk);
}
/*
@@ -970,7 +778,7 @@ static int at91_set_selfpowered(struct usb_gadget *gadget, int is_on)
unsigned long flags;
spin_lock_irqsave(&udc->lock, flags);
- gadget->is_selfpowered = (is_on != 0);
+ udc->selfpowered = (is_on != 0);
spin_unlock_irqrestore(&udc->lock, flags);
return 0;
}
@@ -1119,7 +927,7 @@ static void handle_setup(struct at91_udc *udc, struct at91_ep *ep, u32 csr)
*/
case ((USB_DIR_IN|USB_TYPE_STANDARD|USB_RECIP_DEVICE) << 8)
| USB_REQ_GET_STATUS:
- tmp = (udc->gadget.is_selfpowered << USB_DEVICE_SELF_POWERED);
+ tmp = (udc->selfpowered << USB_DEVICE_SELF_POWERED);
if (at91_udp_read(udc, AT91_UDP_GLB_STAT) & AT91_UDP_ESR)
tmp |= (1 << USB_DEVICE_REMOTE_WAKEUP);
PACKET("get device status\n");
@@ -1388,9 +1196,8 @@ static void handle_ep0(struct at91_udc *udc)
}
}
-static irqreturn_t at91_udc_irq (int irq, void *_udc)
+static irqreturn_t at91_udc_irq(struct at91_udc *udc)
{
- struct at91_udc *udc = _udc;
u32 rescans = 5;
int disable_clock = 0;
unsigned long flags;
@@ -1505,67 +1312,23 @@ static irqreturn_t at91_udc_irq (int irq, void *_udc)
/*-------------------------------------------------------------------------*/
-static void at91_vbus_update(struct at91_udc *udc, unsigned value)
-{
- value ^= udc->board.vbus_active_low;
- if (value != udc->vbus)
- at91_vbus_session(&udc->gadget, value);
-}
-
-static irqreturn_t at91_vbus_irq(int irq, void *_udc)
-{
- struct at91_udc *udc = _udc;
-
- /* vbus needs at least brief debouncing */
- udelay(10);
- at91_vbus_update(udc, gpio_get_value(udc->board.vbus_pin));
-
- return IRQ_HANDLED;
-}
-
-static void at91_vbus_timer_work(struct work_struct *work)
-{
- struct at91_udc *udc = container_of(work, struct at91_udc,
- vbus_timer_work);
-
- at91_vbus_update(udc, gpio_get_value_cansleep(udc->board.vbus_pin));
-
- if (!timer_pending(&udc->vbus_timer))
- mod_timer(&udc->vbus_timer, jiffies + VBUS_POLL_TIMEOUT);
-}
-
-static void at91_vbus_timer(unsigned long data)
-{
- struct at91_udc *udc = (struct at91_udc *)data;
-
- /*
- * If we are polling vbus it is likely that the gpio is on an
- * bus such as i2c or spi which may sleep, so schedule some work
- * to read the vbus gpio
- */
- schedule_work(&udc->vbus_timer_work);
-}
-
static int at91_start(struct usb_gadget *gadget,
struct usb_gadget_driver *driver)
{
- struct at91_udc *udc;
+ struct at91_udc *udc = controller;
- udc = container_of(gadget, struct at91_udc, gadget);
udc->driver = driver;
- udc->gadget.dev.of_node = udc->pdev->dev.of_node;
udc->enabled = 1;
- udc->gadget.is_selfpowered = 1;
+ udc->selfpowered = 1;
return 0;
}
static int at91_stop(struct usb_gadget *gadget)
{
- struct at91_udc *udc;
+ struct at91_udc *udc = controller;
unsigned long flags;
- udc = container_of(gadget, struct at91_udc, gadget);
spin_lock_irqsave(&udc->lock, flags);
udc->enabled = 0;
at91_udp_write(udc, AT91_UDP_IDR, ~0);
@@ -1578,17 +1341,6 @@ static int at91_stop(struct usb_gadget *gadget)
/*-------------------------------------------------------------------------*/
-static void at91udc_shutdown(struct platform_device *dev)
-{
- struct at91_udc *udc = platform_get_drvdata(dev);
- unsigned long flags;
-
- /* force disconnect on reboot */
- spin_lock_irqsave(&udc->lock, flags);
- pullup(platform_get_drvdata(dev), 0);
- spin_unlock_irqrestore(&udc->lock, flags);
-}
-
static int at91rm9200_udc_init(struct at91_udc *udc)
{
struct at91_ep *ep;
@@ -1612,13 +1364,7 @@ static int at91rm9200_udc_init(struct at91_udc *udc)
}
}
- if (!gpio_is_valid(udc->board.pullup_pin)) {
- DBG("no D+ pullup?\n");
- return -ENODEV;
- }
-
- ret = devm_gpio_request(&udc->pdev->dev, udc->board.pullup_pin,
- "udc_pullup");
+ ret = gpio_request(udc->board.pullup_pin, "udc_pullup");
if (ret) {
DBG("D+ pullup is busy\n");
return ret;
@@ -1666,6 +1412,7 @@ static int at91sam9260_udc_init(struct at91_udc *udc)
return 0;
}
+#if defined(CONFIG_AT91SAM9260) || defined(CONFIG_AT91SAM9G20)
static void at91sam9260_udc_pullup(struct at91_udc *udc, int is_on)
{
u32 txvc = at91_udp_read(udc, AT91_UDP_TXVC);
@@ -1682,7 +1429,9 @@ static const struct at91_udc_caps at91sam9260_udc_caps = {
.init = at91sam9260_udc_init,
.pullup = at91sam9260_udc_pullup,
};
+#endif
+#if defined(CONFIG_AT91SAM9261)
static int at91sam9261_udc_init(struct at91_udc *udc)
{
struct at91_ep *ep;
@@ -1704,8 +1453,8 @@ static int at91sam9261_udc_init(struct at91_udc *udc)
}
}
- udc->matrix = syscon_regmap_lookup_by_phandle(udc->pdev->dev.of_node,
- "atmel,matrix");
+ udc->matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+
if (IS_ERR(udc->matrix))
return PTR_ERR(udc->matrix);
@@ -1716,17 +1465,18 @@ static void at91sam9261_udc_pullup(struct at91_udc *udc, int is_on)
{
u32 usbpucr = 0;
+ usbpucr = readl(&udc->matrix->pucr);
if (is_on)
- usbpucr = AT91_MATRIX_USBPUCR_PUON;
+ usbpucr |= AT91_MATRIX_USBPUCR_PUON;
- regmap_update_bits(udc->matrix, AT91SAM9261_MATRIX_USBPUCR,
- AT91_MATRIX_USBPUCR_PUON, usbpucr);
+ writel(usbpucr, &udc->matrix->pucr);
}
static const struct at91_udc_caps at91sam9261_udc_caps = {
.init = at91sam9261_udc_init,
.pullup = at91sam9261_udc_pullup,
};
+#endif
static int at91sam9263_udc_init(struct at91_udc *udc)
{
@@ -1758,75 +1508,90 @@ static const struct at91_udc_caps at91sam9263_udc_caps = {
.pullup = at91sam9260_udc_pullup,
};
-static const struct of_device_id at91_udc_dt_ids[] = {
- {
- .compatible = "atmel,at91rm9200-udc",
- .data = &at91rm9200_udc_caps,
- },
- {
- .compatible = "atmel,at91sam9260-udc",
- .data = &at91sam9260_udc_caps,
- },
- {
- .compatible = "atmel,at91sam9261-udc",
- .data = &at91sam9261_udc_caps,
- },
- {
- .compatible = "atmel,at91sam9263-udc",
- .data = &at91sam9263_udc_caps,
- },
- { /* sentinel */ }
-};
-MODULE_DEVICE_TABLE(of, at91_udc_dt_ids);
+int usb_gadget_handle_interrupts(int index)
+{
+ struct at91_udc *udc = controller;
-static void at91udc_of_init(struct at91_udc *udc, struct device_node *np)
+ return at91_udc_irq(udc);
+}
+
+int usb_gadget_register_driver(struct usb_gadget_driver *driver)
{
- struct at91_udc_data *board = &udc->board;
- const struct of_device_id *match;
- enum of_gpio_flags flags;
- u32 val;
+ struct at91_udc *udc = controller;
+ int ret;
- if (of_property_read_u32(np, "atmel,vbus-polled", &val) == 0)
- board->vbus_polled = 1;
+ if (!driver || !driver->bind || !driver->setup) {
+ printf("bad paramter\n");
+ return -EINVAL;
+ }
+
+ if (udc->driver) {
+ printf("UDC already has a gadget driver\n");
+ return -EBUSY;
+ }
- board->vbus_pin = of_get_named_gpio_flags(np, "atmel,vbus-gpio", 0,
- &flags);
- board->vbus_active_low = (flags & OF_GPIO_ACTIVE_LOW) ? 1 : 0;
+ at91_start(&udc->gadget, driver);
- board->pullup_pin = of_get_named_gpio_flags(np, "atmel,pullup-gpio", 0,
- &flags);
+ udc->driver = driver;
- board->pullup_active_low = (flags & OF_GPIO_ACTIVE_LOW) ? 1 : 0;
+ ret = driver->bind(&udc->gadget);
+ if (ret) {
+ error("driver->bind() returned %d\n", ret);
+ udc->driver = NULL;
+ }
- match = of_match_node(at91_udc_dt_ids, np);
- if (match)
- udc->caps = match->data;
+ return ret;
}
-static int at91udc_probe(struct platform_device *pdev)
+int usb_gadget_unregister_driver(struct usb_gadget_driver *driver)
+{
+ struct at91_udc *udc = controller;
+
+ if (!driver || !driver->unbind || !driver->disconnect) {
+ error("bad paramter\n");
+ return -EINVAL;
+ }
+
+ driver->disconnect(&udc->gadget);
+ driver->unbind(&udc->gadget);
+ udc->driver = NULL;
+
+ at91_stop(&udc->gadget);
+
+ return 0;
+}
+
+int at91_udc_probe(struct at91_udc_data *pdata)
{
- struct device *dev = &pdev->dev;
struct at91_udc *udc;
int retval;
- struct resource *res;
struct at91_ep *ep;
int i;
- udc = devm_kzalloc(dev, sizeof(*udc), GFP_KERNEL);
+ udc = kzalloc(sizeof(*udc), GFP_KERNEL);
if (!udc)
return -ENOMEM;
- /* init software state */
- udc->gadget.dev.parent = dev;
- at91udc_of_init(udc, pdev->dev.of_node);
- udc->pdev = pdev;
+ controller = udc;
+ memcpy(&udc->board, pdata, sizeof(struct at91_udc_data));
+ if (udc->board.vbus_pin) {
+ printf("%s: gpio vbus pin not supported yet.\n", __func__);
+ return -ENXIO;
+ } else {
+ DBG("no VBUS detection, assuming always-on\n");
+ udc->vbus = 1;
+ }
+
+#if defined(CONFIG_AT91SAM9260) || defined(CONFIG_AT91SAM9G20)
+ udc->caps = &at91sam9260_udc_caps;
+#endif
+
udc->enabled = 0;
spin_lock_init(&udc->lock);
udc->gadget.ops = &at91_udc_ops;
udc->gadget.ep0 = &udc->ep[0].ep;
udc->gadget.name = driver_name;
- udc->gadget.dev.init_name = "gadget";
for (i = 0; i < NUM_ENDPOINTS; i++) {
ep = &udc->ep[i];
@@ -1838,8 +1603,7 @@ static int at91udc_probe(struct platform_device *pdev)
ep->is_pingpong = 1;
}
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- udc->udp_baseaddr = devm_ioremap_resource(dev, res);
+ udc->udp_baseaddr = (void *)udc->board.baseaddr;
if (IS_ERR(udc->udp_baseaddr))
return PTR_ERR(udc->udp_baseaddr);
@@ -1851,186 +1615,11 @@ static int at91udc_probe(struct platform_device *pdev)
udc_reinit(udc);
- /* get interface and function clocks */
- udc->iclk = devm_clk_get(dev, "pclk");
- if (IS_ERR(udc->iclk))
- return PTR_ERR(udc->iclk);
-
- udc->fclk = devm_clk_get(dev, "hclk");
- if (IS_ERR(udc->fclk))
- return PTR_ERR(udc->fclk);
-
- /* don't do anything until we have both gadget driver and VBUS */
- clk_set_rate(udc->fclk, 48000000);
- retval = clk_prepare(udc->fclk);
- if (retval)
- return retval;
-
- retval = clk_prepare_enable(udc->iclk);
- if (retval)
- goto err_unprepare_fclk;
-
at91_udp_write(udc, AT91_UDP_TXVC, AT91_UDP_TXVC_TXVDIS);
at91_udp_write(udc, AT91_UDP_IDR, 0xffffffff);
/* Clear all pending interrupts - UDP may be used by bootloader. */
at91_udp_write(udc, AT91_UDP_ICR, 0xffffffff);
- clk_disable(udc->iclk);
-
- /* request UDC and maybe VBUS irqs */
- udc->udp_irq = platform_get_irq(pdev, 0);
- retval = devm_request_irq(dev, udc->udp_irq, at91_udc_irq, 0,
- driver_name, udc);
- if (retval) {
- DBG("request irq %d failed\n", udc->udp_irq);
- goto err_unprepare_iclk;
- }
-
- if (gpio_is_valid(udc->board.vbus_pin)) {
- retval = devm_gpio_request(dev, udc->board.vbus_pin,
- "udc_vbus");
- if (retval) {
- DBG("request vbus pin failed\n");
- goto err_unprepare_iclk;
- }
-
- gpio_direction_input(udc->board.vbus_pin);
-
- /*
- * Get the initial state of VBUS - we cannot expect
- * a pending interrupt.
- */
- udc->vbus = gpio_get_value_cansleep(udc->board.vbus_pin) ^
- udc->board.vbus_active_low;
-
- if (udc->board.vbus_polled) {
- INIT_WORK(&udc->vbus_timer_work, at91_vbus_timer_work);
- setup_timer(&udc->vbus_timer, at91_vbus_timer,
- (unsigned long)udc);
- mod_timer(&udc->vbus_timer,
- jiffies + VBUS_POLL_TIMEOUT);
- } else {
- retval = devm_request_irq(dev,
- gpio_to_irq(udc->board.vbus_pin),
- at91_vbus_irq, 0, driver_name, udc);
- if (retval) {
- DBG("request vbus irq %d failed\n",
- udc->board.vbus_pin);
- goto err_unprepare_iclk;
- }
- }
- } else {
- DBG("no VBUS detection, assuming always-on\n");
- udc->vbus = 1;
- }
- retval = usb_add_gadget_udc(dev, &udc->gadget);
- if (retval)
- goto err_unprepare_iclk;
- dev_set_drvdata(dev, udc);
- device_init_wakeup(dev, 1);
- create_debug_file(udc);
INFO("%s version %s\n", driver_name, DRIVER_VERSION);
return 0;
-
-err_unprepare_iclk:
- clk_unprepare(udc->iclk);
-err_unprepare_fclk:
- clk_unprepare(udc->fclk);
-
- DBG("%s probe failed, %d\n", driver_name, retval);
-
- return retval;
-}
-
-static int at91udc_remove(struct platform_device *pdev)
-{
- struct at91_udc *udc = platform_get_drvdata(pdev);
- unsigned long flags;
-
- DBG("remove\n");
-
- usb_del_gadget_udc(&udc->gadget);
- if (udc->driver)
- return -EBUSY;
-
- spin_lock_irqsave(&udc->lock, flags);
- pullup(udc, 0);
- spin_unlock_irqrestore(&udc->lock, flags);
-
- device_init_wakeup(&pdev->dev, 0);
- remove_debug_file(udc);
- clk_unprepare(udc->fclk);
- clk_unprepare(udc->iclk);
-
- return 0;
}
-
-#ifdef CONFIG_PM
-static int at91udc_suspend(struct platform_device *pdev, pm_message_t mesg)
-{
- struct at91_udc *udc = platform_get_drvdata(pdev);
- int wake = udc->driver && device_may_wakeup(&pdev->dev);
- unsigned long flags;
-
- /* Unless we can act normally to the host (letting it wake us up
- * whenever it has work for us) force disconnect. Wakeup requires
- * PLLB for USB events (signaling for reset, wakeup, or incoming
- * tokens) and VBUS irqs (on systems which support them).
- */
- if ((!udc->suspended && udc->addr)
- || !wake
- || at91_suspend_entering_slow_clock()) {
- spin_lock_irqsave(&udc->lock, flags);
- pullup(udc, 0);
- wake = 0;
- spin_unlock_irqrestore(&udc->lock, flags);
- } else
- enable_irq_wake(udc->udp_irq);
-
- udc->active_suspend = wake;
- if (gpio_is_valid(udc->board.vbus_pin) && !udc->board.vbus_polled && wake)
- enable_irq_wake(udc->board.vbus_pin);
- return 0;
-}
-
-static int at91udc_resume(struct platform_device *pdev)
-{
- struct at91_udc *udc = platform_get_drvdata(pdev);
- unsigned long flags;
-
- if (gpio_is_valid(udc->board.vbus_pin) && !udc->board.vbus_polled &&
- udc->active_suspend)
- disable_irq_wake(udc->board.vbus_pin);
-
- /* maybe reconnect to host; if so, clocks on */
- if (udc->active_suspend)
- disable_irq_wake(udc->udp_irq);
- else {
- spin_lock_irqsave(&udc->lock, flags);
- pullup(udc, 1);
- spin_unlock_irqrestore(&udc->lock, flags);
- }
- return 0;
-}
-#else
-#define at91udc_suspend NULL
-#define at91udc_resume NULL
-#endif
-
-static struct platform_driver at91_udc_driver = {
- .remove = at91udc_remove,
- .shutdown = at91udc_shutdown,
- .suspend = at91udc_suspend,
- .resume = at91udc_resume,
- .driver = {
- .name = (char *) driver_name,
- .of_match_table = at91_udc_dt_ids,
- },
-};
-
-module_platform_driver_probe(at91_udc_driver, at91udc_probe);
-
-MODULE_DESCRIPTION("AT91 udc driver");
-MODULE_AUTHOR("Thomas Rathbone, David Brownell");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:at91_udc");
diff --git a/drivers/usb/gadget/at91_udc.h b/drivers/usb/gadget/at91_udc.h
index 2679c8b..3d8752e 100644
--- a/drivers/usb/gadget/at91_udc.h
+++ b/drivers/usb/gadget/at91_udc.h
@@ -128,18 +128,14 @@ struct at91_udc {
unsigned req_pending:1;
unsigned wait_for_addr_ack:1;
unsigned wait_for_config_ack:1;
+ unsigned selfpowered:1;
unsigned active_suspend:1;
u8 addr;
struct at91_udc_data board;
- struct clk *iclk, *fclk;
- struct platform_device *pdev;
- struct proc_dir_entry *pde;
void __iomem *udp_baseaddr;
int udp_irq;
spinlock_t lock;
- struct timer_list vbus_timer;
- struct work_struct vbus_timer_work;
- struct regmap *matrix;
+ struct at91_matrix *matrix;
};
static inline struct at91_udc *to_udc(struct usb_gadget *g)
@@ -166,10 +162,10 @@ struct at91_request {
# define PACKET(stuff...) do{}while(0)
#endif
-#define ERR(stuff...) pr_err("udc: " stuff)
-#define WARNING(stuff...) pr_warning("udc: " stuff)
-#define INFO(stuff...) pr_info("udc: " stuff)
-#define DBG(stuff...) pr_debug("udc: " stuff)
+#define ERR(stuff...) debug("udc: " stuff)
+#define WARNING(stuff...) debug("udc: " stuff)
+#define INFO(stuff...) debug("udc: " stuff)
+#define DBG(stuff...) debug("udc: " stuff)
#endif
diff --git a/include/linux/usb/at91_udc.h b/include/linux/usb/at91_udc.h
new file mode 100644
index 0000000..cd0d00f
--- /dev/null
+++ b/include/linux/usb/at91_udc.h
@@ -0,0 +1,20 @@
+/*
+ * Platform data definitions for Atmel USBA gadget driver
+ * pieces copied from linux:include/linux/platform_data/atmel.h
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#ifndef __LINUX_USB_AT91_UDC_H__
+#define __LINUX_USB_AT91_UDC_H__
+
+struct at91_udc_data {
+ int vbus_pin; /* high == host powering us */
+ u8 vbus_active_low; /* vbus polarity */
+ u8 vbus_polled; /* Use polling, not interrupt */
+ int pullup_pin; /* active == D+ pulled up */
+ u8 pullup_active_low; /* true == pullup_pin is active low */
+ unsigned long baseaddr;
+};
+
+int at91_udc_probe(struct at91_udc_data *pdata);
+#endif /* __LINUX_USB_AT91_UDC_H__ */
--
2.1.0
More information about the U-Boot
mailing list