[U-Boot] [PATCH v4] x86: baytrail: Configure FSP UPD from device tree
Bin Meng
bmeng.cn at gmail.com
Thu Aug 13 09:55:26 CEST 2015
Hi Simon,
On Wed, Aug 12, 2015 at 11:54 AM, Simon Glass <sjg at chromium.org> wrote:
> +Gabriel
>
> Hi Andrew,
>
> On 11 August 2015 at 09:20, Andrew Bradford <andrew at bradfordembedded.com> wrote:
>> Hi Simon,
>>
>> On 08/11 08:06, Simon Glass wrote:
>>> Hi Andrew,
>>>
>>> On 11 August 2015 at 06:08, Andrew Bradford <andrew at bradfordembedded.com> wrote:
>>> > Hi Simon,
>>> >
>>> > On 08/10 21:07, Simon Glass wrote:
>>> >> Hi Bin,
>>> >>
>>> >> On 10 August 2015 at 20:53, Bin Meng <bmeng.cn at gmail.com> wrote:
>>> >> > Hi Andrew,
>>> >> >
>>> >> > On Mon, Aug 10, 2015 at 7:32 PM, Andrew Bradford
>>> >> > <andrew at bradfordembedded.com> wrote:
>>> >> >> Hi Bin,
>>> >> >>
>>> >> >> On 08/09 10:52, Bin Meng wrote:
>>> >> >>> Hi Andrew,
>>> >> >>>
>>> >> >>> On Sun, Aug 9, 2015 at 9:08 AM, Andrew Bradford
>>> >> >>> <andrew at bradfordembedded.com> wrote:
>>> >> >>> > Hi Simon,
>>> >> >>> >
>>> >> >>> > On 08/08 10:18, Simon Glass wrote:
>>> >> >>> >> Hi,
>>> >> >>> >>
>>> >> >>> >> On 7 August 2015 at 06:44, Bin Meng <bmeng.cn at gmail.com> wrote:
>>> >> >>> >> > On Fri, Aug 7, 2015 at 8:36 PM, Andrew Bradford
>>> >> >>> >> > <andrew at bradfordembedded.com> wrote:
>>> >> >>> >> >> From: Andrew Bradford <andrew.bradford at kodakalaris.com>
>>> >> >>> >> >>
>>> >> >>> >> >> Allow for configuration of FSP UPD from the device tree which will
>>> >> >>> >> >> override any settings which the FSP was built with itself.
>>> >> >>> >> >>
>>> >> >>> >> >> Modify the MinnowMax and BayleyBay boards to transfer sensible UPD
>>> >> >>> >> >> settings from the Intel FSPv4 Gold release to the respective dts files,
>>> >> >>> >> >> with the condition that the memory-down parameters for MinnowMax are
>>> >> >>> >> >> also used.
>>> >> >>> >> >>
>>> >> >>> >> >> Signed-off-by: Andrew Bradford <andrew.bradford at kodakalaris.com>
>>> >> >>> >> >> ---
>>> >> >>> >> >>
>>> >> >>> >> >
>>> >> >>> >> > Reviewed-by: Bin Meng <bmeng.cn at gmail.com>
>>> >> >>> >> > Tested-by: Bin Meng <bmeng.cn at gmail.com>
>>> >> >>> >> >
>>> >> >>> >>
>>> >> >>> >> Acked-by: Simon Glass <sjg at chromium.org>
>>> >> >>> >> Tested on minnowmax:
>>> >> >>> >> Tested-by: Simon Glass <sjg at chromium.org>
>>> >> >>> >>
>>> >> >>> >> I found that I need to remove two properties from the minnowmax.dts:
>>> >> >>> >>
>>> >> >>> >> - fsp,enable-xhci needs to be removed as this does not work in U-Boot
>>> >> >>> >> at present and stops EHCI from working
>>> >> >>> >> - fsp,mrc-debug-msg needs to be removed to prevent debug information
>>> >> >>> >> being displayed
>>> >> >>> >>
>>> >> >>> >> I plan to apply this with these changes - please let me know if this
>>> >> >>> >> doesn't suit.
>>> >> >>> >
>>> >> >>> > I'm OK with disabling xhci and the MRC debug output in the FSP.
>>> >> >>> >
>>> >> >>> > But if xhci is disabled then I believe when Linux boots that the USB 3.0
>>> >> >>> > port on Minnow Max will only act as a USB 2.0 port. That u-boot doesn't
>>> >> >>> > yet have working XHCI on E3800 means there is a tradeoff and I wasn't
>>> >> >>> > sure which was a better choice.
>>> >> >>>
>>> >> >>> Does these xHCI ports on MinnowMax work fully on Linux kernel? If it
>>> >> >>> works, I'd rather we keep fsp,enable-xhci in the U-Boot.
>>> >> >>
>>> >> >> I believe that the xhci port does work on Minnow Max in Linux but I do
>>> >> >> not have a board so I'm unable to test, sorry.
>>> >> >>
>>> >> >
>>> >> > OK, my test shows that ehci works fine in U-Boot on Bayley Bay.
>>> >> >
>>> >> > Hi Simon,
>>> >> >
>>> >> > What do you think regarding to xhci vs. ehci in U-Boot?
>>> >>
>>> >> The problem is that USB is then broken in U-Boot. I think it is better
>>> >> to limit the speed for the moment until we have that fixed. It is
>>> >> quite useful to be able to use a keyboard or USB stick in U-Boot.
>>> >>
>>> >> With my testing the bottom (blue) port works fine but the top port
>>> >> does not. This happens regardless of the xhci setting.
>>> >
>>> > Minnowmax has a USB power switch enable which determines if the VBUS2
>>> > net is turned on or not, which will supply or not supply power to the
>>> > USB 2.0 port. The blue USB 3.0 port also has an enable. Both enables
>>> > and the USB ports themselves are located on page 16 of the schematic
>>> > that I have.
>>> >
>>> > The switches to enable the VBUS for each port are active high and pulled
>>> > down. So to turn them on, I believe that's the point of the pinmuxing
>>> > and GPIO settings which are used in the minnowmax.dts. Can you verify
>>> > if these are correctly turning on VBUS2 (since it sounds like they are
>>> > turning on VBUS1)? If not, when you turn these GPIO on manually, does
>>> > the USB 2.0 port work correctly?
>>>
>>> I see power on the bottom port but not the top one.
>>
>> OK, that's odd, but likely can be fixed with changes to the pin mux and
>> pad settings in the dts. I believe that the "pad-offset" for
>> pin_usb_host_en1 at 0 is wrong and that it should be 0x250 instead of
>> 0x258.
>>
>> diff --git a/arch/x86/dts/minnowmax.dts b/arch/x86/dts/minnowmax.dts
>> index d0c0fe6..4988163 100644
>> --- a/arch/x86/dts/minnowmax.dts
>> +++ b/arch/x86/dts/minnowmax.dts
>> @@ -39,7 +39,7 @@
>>
>> pin_usb_host_en1 at 0 {
>> gpio-offset = <0x80 9>;
>> - pad-offset = <0x258>;
>> + pad-offset = <0x250>;
>> mode-gpio;
>> output-value = <1>;
>> direction = <PIN_OUTPUT>;
>>
>> Does that fix it?
>
> I dug into this a bit and it all seems quite broken:
>
> - PCI bus configuration does not work in gpio_ich6_pinctrl_init(). I
> will send a patch for this
I believe it indeed worked in the past but with the DM PCI conversion
on MinnowMax recently it was broken. That's also why I sent a patch
[1] previously saying that we should explicitly trigger the PCI
enumeration process, as not all DM PCI APIs can trigger the PCI
enumeration, which it is supposed to be as per DM concept.
> - gpio_ich6_get_base() returns a 16-bit word but function is also used
> to read the memory address which holds a 32-bit word
> - Intel's hardware won't let you read the status of an output!
>
> The last point means that _gpio_ich6_pinctrl_cfg_pin cannot work. We
> need to mirror the lvl register in order to be able to read it.
>
> I confirmed that with the 'correct' value in the lvl registers both
> USB ports work.
>
[1]: http://lists.denx.de/pipermail/u-boot/2015-July/220542.html
Regards,
Bin
More information about the U-Boot
mailing list