[U-Boot] [RFC PATCH 01/28] powerpc: remove alpr support
Masahiro Yamada
yamada.masahiro at socionext.com
Thu Aug 13 12:15:19 CEST 2015
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro at socionext.com>
---
arch/powerpc/cpu/ppc4xx/Kconfig | 4 -
board/prodrive/alpr/Kconfig | 12 --
board/prodrive/alpr/MAINTAINERS | 6 -
board/prodrive/alpr/Makefile | 9 --
board/prodrive/alpr/alpr.c | 215 ------------------------
board/prodrive/alpr/config.mk | 16 --
board/prodrive/alpr/fpga.c | 239 ---------------------------
board/prodrive/alpr/init.S | 53 ------
board/prodrive/alpr/nand.c | 124 --------------
configs/alpr_defconfig | 7 -
include/configs/alpr.h | 351 ----------------------------------------
11 files changed, 1036 deletions(-)
delete mode 100644 board/prodrive/alpr/Kconfig
delete mode 100644 board/prodrive/alpr/MAINTAINERS
delete mode 100644 board/prodrive/alpr/Makefile
delete mode 100644 board/prodrive/alpr/alpr.c
delete mode 100644 board/prodrive/alpr/config.mk
delete mode 100644 board/prodrive/alpr/fpga.c
delete mode 100644 board/prodrive/alpr/init.S
delete mode 100644 board/prodrive/alpr/nand.c
delete mode 100644 configs/alpr_defconfig
delete mode 100644 include/configs/alpr.h
diff --git a/arch/powerpc/cpu/ppc4xx/Kconfig b/arch/powerpc/cpu/ppc4xx/Kconfig
index 10b86e0..e8c0ca0 100644
--- a/arch/powerpc/cpu/ppc4xx/Kconfig
+++ b/arch/powerpc/cpu/ppc4xx/Kconfig
@@ -140,9 +140,6 @@ config TARGET_MIP405
config TARGET_PIP405
bool "Support PIP405"
-config TARGET_ALPR
- bool "Support alpr"
-
config TARGET_P3P440
bool "Support p3p440"
@@ -197,7 +194,6 @@ source "board/mosaixtech/icon/Kconfig"
source "board/mpl/mip405/Kconfig"
source "board/mpl/pip405/Kconfig"
source "board/pcs440ep/Kconfig"
-source "board/prodrive/alpr/Kconfig"
source "board/prodrive/p3p440/Kconfig"
source "board/sbc405/Kconfig"
source "board/t3corp/Kconfig"
diff --git a/board/prodrive/alpr/Kconfig b/board/prodrive/alpr/Kconfig
deleted file mode 100644
index 543b455..0000000
--- a/board/prodrive/alpr/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_ALPR
-
-config SYS_BOARD
- default "alpr"
-
-config SYS_VENDOR
- default "prodrive"
-
-config SYS_CONFIG_NAME
- default "alpr"
-
-endif
diff --git a/board/prodrive/alpr/MAINTAINERS b/board/prodrive/alpr/MAINTAINERS
deleted file mode 100644
index 31baabb..0000000
--- a/board/prodrive/alpr/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-ALPR BOARD
-M: Stefan Roese <sr at denx.de>
-S: Maintained
-F: board/prodrive/alpr/
-F: include/configs/alpr.h
-F: configs/alpr_defconfig
diff --git a/board/prodrive/alpr/Makefile b/board/prodrive/alpr/Makefile
deleted file mode 100644
index 812d041..0000000
--- a/board/prodrive/alpr/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = alpr.o fpga.o nand.o
-extra-y += init.o
diff --git a/board/prodrive/alpr/alpr.c b/board/prodrive/alpr/alpr.c
deleted file mode 100644
index 31c1ab5..0000000
--- a/board/prodrive/alpr/alpr.c
+++ /dev/null
@@ -1,215 +0,0 @@
-/*
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-
-#include <common.h>
-#include <libfdt.h>
-#include <fdt_support.h>
-#include <spd_sdram.h>
-#include <asm/ppc4xx-emac.h>
-#include <miiphy.h>
-#include <asm/processor.h>
-#include <asm/4xx_pci.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-extern int alpr_fpga_init(void);
-
-int board_early_init_f (void)
-{
- /*-------------------------------------------------------------------------
- * Initialize EBC CONFIG
- *-------------------------------------------------------------------------*/
- mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK |
- EBC_CFG_PTD_DISABLE | EBC_CFG_RTC_64PERCLK |
- EBC_CFG_ATC_PREVIOUS | EBC_CFG_DTC_PREVIOUS |
- EBC_CFG_CTC_PREVIOUS | EBC_CFG_EMC_NONDEFAULT |
- EBC_CFG_PME_DISABLE | EBC_CFG_PR_32);
-
- /*--------------------------------------------------------------------
- * Setup the interrupt controller polarities, triggers, etc.
- *-------------------------------------------------------------------*/
- /*
- * Because of the interrupt handling rework to handle 440GX interrupts
- * with the common code, we needed to change names of the UIC registers.
- * Here the new relationship:
- *
- * U-Boot name 440GX name
- * -----------------------
- * UIC0 UICB0
- * UIC1 UIC0
- * UIC2 UIC1
- * UIC3 UIC2
- */
- mtdcr (UIC1SR, 0xffffffff); /* clear all */
- mtdcr (UIC1ER, 0x00000000); /* disable all */
- mtdcr (UIC1CR, 0x00000009); /* SMI & UIC1 crit are critical */
- mtdcr (UIC1PR, 0xfffffe03); /* per manual */
- mtdcr (UIC1TR, 0x01c00000); /* per manual */
- mtdcr (UIC1VR, 0x00000001); /* int31 highest, base=0x000 */
- mtdcr (UIC1SR, 0xffffffff); /* clear all */
-
- mtdcr (UIC2SR, 0xffffffff); /* clear all */
- mtdcr (UIC2ER, 0x00000000); /* disable all */
- mtdcr (UIC2CR, 0x00000000); /* all non-critical */
- mtdcr (UIC2PR, 0xffffe0ff); /* per ref-board manual */
- mtdcr (UIC2TR, 0x00ffc000); /* per ref-board manual */
- mtdcr (UIC2VR, 0x00000001); /* int31 highest, base=0x000 */
- mtdcr (UIC2SR, 0xffffffff); /* clear all */
-
- mtdcr (UIC3SR, 0xffffffff); /* clear all */
- mtdcr (UIC3ER, 0x00000000); /* disable all */
- mtdcr (UIC3CR, 0x00000000); /* all non-critical */
- mtdcr (UIC3PR, 0xffffffff); /* per ref-board manual */
- mtdcr (UIC3TR, 0x00ff8c0f); /* per ref-board manual */
- mtdcr (UIC3VR, 0x00000001); /* int31 highest, base=0x000 */
- mtdcr (UIC3SR, 0xffffffff); /* clear all */
-
- mtdcr (UIC0SR, 0xfc000000); /* clear all */
- mtdcr (UIC0ER, 0x00000000); /* disable all */
- mtdcr (UIC0CR, 0x00000000); /* all non-critical */
- mtdcr (UIC0PR, 0xfc000000); /* */
- mtdcr (UIC0TR, 0x00000000); /* */
- mtdcr (UIC0VR, 0x00000001); /* */
-
- /* Setup shutdown/SSD empty interrupt as inputs */
- out32(GPIO0_TCR, in32(GPIO0_TCR) & ~(CONFIG_SYS_GPIO_SHUTDOWN | CONFIG_SYS_GPIO_SSD_EMPTY));
- out32(GPIO0_ODR, in32(GPIO0_ODR) & ~(CONFIG_SYS_GPIO_SHUTDOWN | CONFIG_SYS_GPIO_SSD_EMPTY));
-
- /* Setup GPIO/IRQ multiplexing */
- mtsdr(SDR0_PFC0, 0x01a33e00);
-
- return 0;
-}
-
-int last_stage_init(void)
-{
- unsigned short reg;
-
- /*
- * Configure LED's of both Marvell 88E1111 PHY's
- *
- * This has to be done after the 4xx ethernet driver is loaded,
- * so "last_stage_init()" is the right place.
- */
- miiphy_read("ppc_4xx_eth2", CONFIG_PHY2_ADDR, 0x18, ®);
- reg |= 0x0001;
- miiphy_write("ppc_4xx_eth2", CONFIG_PHY2_ADDR, 0x18, reg);
- miiphy_read("ppc_4xx_eth3", CONFIG_PHY3_ADDR, 0x18, ®);
- reg |= 0x0001;
- miiphy_write("ppc_4xx_eth3", CONFIG_PHY3_ADDR, 0x18, reg);
-
- return 0;
-}
-
-static int board_rev(void)
-{
- /* Setup as input */
- out32(GPIO0_TCR, in32(GPIO0_TCR) & ~(CONFIG_SYS_GPIO_REV0 | CONFIG_SYS_GPIO_REV1));
- out32(GPIO0_ODR, in32(GPIO0_ODR) & ~(CONFIG_SYS_GPIO_REV0 | CONFIG_SYS_GPIO_REV1));
-
- return (in32(GPIO0_IR) >> 16) & 0x3;
-}
-
-int checkboard (void)
-{
- char buf[64];
- int i = getenv_f("serial#", buf, sizeof(buf));
-
- printf ("Board: ALPR");
- if (i > 0) {
- puts(", serial# ");
- puts(buf);
- }
- printf(" (Rev. %d)\n", board_rev());
-
- return (0);
-}
-
-#if defined(CONFIG_PCI)
-/*
- * Override weak pci_pre_init()
- */
-int pci_pre_init(struct pci_controller *hose)
-{
- if (__pci_pre_init(hose) == 0)
- return 0;
-
- /* FPGA Init */
- alpr_fpga_init();
-
- return 1;
-}
-
-/*************************************************************************
- * Override weak is_pci_host()
- *
- * This routine is called to determine if a pci scan should be
- * performed. With various hardware environments (especially cPCI and
- * PPMC) it's insufficient to depend on the state of the arbiter enable
- * bit in the strap register, or generic host/adapter assumptions.
- *
- * Rather than hard-code a bad assumption in the general 440 code, the
- * 440 pci code requires the board to decide at runtime.
- *
- * Return 0 for adapter mode, non-zero for host (monarch) mode.
- *
- *
- ************************************************************************/
-static void wait_for_pci_ready(void)
-{
- /*
- * Configure EREADY as input
- */
- out32(GPIO0_TCR, in32(GPIO0_TCR) & ~CONFIG_SYS_GPIO_EREADY);
- udelay(1000);
-
- for (;;) {
- if (in32(GPIO0_IR) & CONFIG_SYS_GPIO_EREADY)
- return;
- }
-
-}
-
-int is_pci_host(struct pci_controller *hose)
-{
- wait_for_pci_ready();
- return 1; /* return 1 for host controller */
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_master_init
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
-void pci_master_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- | PowerPC440 PCI Master configuration.
- | Map PLB/processor addresses to PCI memory space.
- | PLB address 0xA0000000-0xCFFFFFFF ==> PCI address 0x80000000-0xCFFFFFFF
- | Use byte reversed out routines to handle endianess.
- | Make this region non-prefetchable.
- +--------------------------------------------------------------------------*/
- out32r( PCIL0_POM0SA, 0 ); /* disable */
- out32r( PCIL0_POM1SA, 0 ); /* disable */
- out32r( PCIL0_POM2SA, 0 ); /* disable */
-
- out32r(PCIL0_POM0LAL, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIL0_POM0LAH, 0x00000003); /* PMM0 Local Address */
- out32r(PCIL0_POM0PCIAL, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIL0_POM0PCIAH, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_POM0SA, ~(0x10000000 - 1) | 1); /* 256MB + enable region */
-
- out32r(PCIL0_POM1LAL, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIL0_POM1LAH, 0x00000003); /* PMM0 Local Address */
- out32r(PCIL0_POM1PCIAL, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIL0_POM1PCIAH, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_POM1SA, ~(0x10000000 - 1) | 1); /* 256MB + enable region */
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
diff --git a/board/prodrive/alpr/config.mk b/board/prodrive/alpr/config.mk
deleted file mode 100644
index 0ccb2e6..0000000
--- a/board/prodrive/alpr/config.mk
+++ /dev/null
@@ -1,16 +0,0 @@
-#
-# (C) Copyright 2004
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-PLATFORM_CPPFLAGS += -DCONFIG_440=1
-
-ifeq ($(debug),1)
-PLATFORM_CPPFLAGS += -DDEBUG
-endif
-
-ifeq ($(dbcr),1)
-PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000
-endif
diff --git a/board/prodrive/alpr/fpga.c b/board/prodrive/alpr/fpga.c
deleted file mode 100644
index 3133f94..0000000
--- a/board/prodrive/alpr/fpga.c
+++ /dev/null
@@ -1,239 +0,0 @@
-/*
- * (C) Copyright 2006
- * Heiko Schocher, DENX Software Engineering, hs at denx.de
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * Altera FPGA configuration support for the ALPR computer from prodrive
- */
-
-#include <common.h>
-#include <altera.h>
-#include <ACEX1K.h>
-#include <command.h>
-#include <asm/processor.h>
-#include <asm/ppc440.h>
-#include "fpga.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#if defined(CONFIG_FPGA)
-
-#ifdef FPGA_DEBUG
-#define PRINTF(fmt, args...) printf(fmt , ##args)
-#else
-#define PRINTF(fmt, args...)
-#endif
-
-static unsigned long regval;
-
-#define SET_GPIO_REG_0(reg, bit) do { \
- regval = in32(reg); \
- regval &= ~(0x80000000 >> bit); \
- out32(reg, regval); \
- } while (0)
-
-#define SET_GPIO_REG_1(reg, bit) do { \
- regval = in32(reg); \
- regval |= (0x80000000 >> bit); \
- out32(reg, regval); \
- } while (0)
-
-#define SET_GPIO_0(bit) SET_GPIO_REG_0(GPIO0_OR, bit)
-#define SET_GPIO_1(bit) SET_GPIO_REG_1(GPIO0_OR, bit)
-
-#define FPGA_PRG (0x80000000 >> CONFIG_SYS_GPIO_PROG_EN)
-#define FPGA_CONFIG (0x80000000 >> CONFIG_SYS_GPIO_CONFIG)
-#define FPGA_DATA (0x80000000 >> CONFIG_SYS_GPIO_DATA)
-#define FPGA_CLK (0x80000000 >> CONFIG_SYS_GPIO_CLK)
-#define OLD_VAL (FPGA_PRG | FPGA_CONFIG)
-
-#define SET_FPGA(data) out32(GPIO0_OR, data)
-
-#define FPGA_WRITE_1 do { \
- SET_FPGA(OLD_VAL | 0 | FPGA_DATA); /* set data to 1 */ \
- SET_FPGA(OLD_VAL | FPGA_CLK | FPGA_DATA); /* set data to 1 */ \
-} while (0)
-
-#define FPGA_WRITE_0 do { \
- SET_FPGA(OLD_VAL | 0 | 0); /* set data to 0 */ \
- SET_FPGA(OLD_VAL | FPGA_CLK | 0); /* set data to 1 */ \
-} while (0)
-
-/* Plattforminitializations */
-/* Here we have to set the FPGA Chain */
-/* PROGRAM_PROG_EN = HIGH */
-/* PROGRAM_SEL_DPR = LOW */
-int fpga_pre_fn(int cookie)
-{
- /* Enable the FPGA Chain */
- SET_GPIO_REG_1(GPIO0_TCR, CONFIG_SYS_GPIO_PROG_EN);
- SET_GPIO_REG_0(GPIO0_ODR, CONFIG_SYS_GPIO_PROG_EN);
- SET_GPIO_1(CONFIG_SYS_GPIO_PROG_EN);
- SET_GPIO_REG_1(GPIO0_TCR, CONFIG_SYS_GPIO_SEL_DPR);
- SET_GPIO_REG_0(GPIO0_ODR, CONFIG_SYS_GPIO_SEL_DPR);
- SET_GPIO_0((CONFIG_SYS_GPIO_SEL_DPR));
-
- /* initialize the GPIO Pins */
- /* output */
- SET_GPIO_0(CONFIG_SYS_GPIO_CLK);
- SET_GPIO_REG_1(GPIO0_TCR, CONFIG_SYS_GPIO_CLK);
- SET_GPIO_REG_0(GPIO0_ODR, CONFIG_SYS_GPIO_CLK);
-
- /* output */
- SET_GPIO_0(CONFIG_SYS_GPIO_DATA);
- SET_GPIO_REG_1(GPIO0_TCR, CONFIG_SYS_GPIO_DATA);
- SET_GPIO_REG_0(GPIO0_ODR, CONFIG_SYS_GPIO_DATA);
-
- /* First we set STATUS to 0 then as an input */
- SET_GPIO_REG_1(GPIO0_TCR, CONFIG_SYS_GPIO_STATUS);
- SET_GPIO_REG_0(GPIO0_ODR, CONFIG_SYS_GPIO_STATUS);
- SET_GPIO_0(CONFIG_SYS_GPIO_STATUS);
- SET_GPIO_REG_0(GPIO0_TCR, CONFIG_SYS_GPIO_STATUS);
- SET_GPIO_REG_0(GPIO0_ODR, CONFIG_SYS_GPIO_STATUS);
-
- /* output */
- SET_GPIO_REG_1(GPIO0_TCR, CONFIG_SYS_GPIO_CONFIG);
- SET_GPIO_REG_0(GPIO0_ODR, CONFIG_SYS_GPIO_CONFIG);
- SET_GPIO_0(CONFIG_SYS_GPIO_CONFIG);
-
- /* input */
- SET_GPIO_0(CONFIG_SYS_GPIO_CON_DON);
- SET_GPIO_REG_0(GPIO0_TCR, CONFIG_SYS_GPIO_CON_DON);
- SET_GPIO_REG_0(GPIO0_ODR, CONFIG_SYS_GPIO_CON_DON);
-
- /* CONFIG = 0 STATUS = 0 -> FPGA in reset state */
- SET_GPIO_0(CONFIG_SYS_GPIO_CONFIG);
- return FPGA_SUCCESS;
-}
-
-/* Set the state of CONFIG Pin */
-int fpga_config_fn(int assert_config, int flush, int cookie)
-{
- if (assert_config)
- SET_GPIO_1(CONFIG_SYS_GPIO_CONFIG);
- else
- SET_GPIO_0(CONFIG_SYS_GPIO_CONFIG);
-
- return FPGA_SUCCESS;
-}
-
-/* Returns the state of STATUS Pin */
-int fpga_status_fn(int cookie)
-{
- unsigned long reg;
-
- reg = in32(GPIO0_IR);
- if (reg & (0x80000000 >> CONFIG_SYS_GPIO_STATUS)) {
- PRINTF("STATUS = HIGH\n");
- return FPGA_FAIL;
- }
- PRINTF("STATUS = LOW\n");
- return FPGA_SUCCESS;
-}
-
-/* Returns the state of CONF_DONE Pin */
-int fpga_done_fn(int cookie)
-{
- unsigned long reg;
- reg = in32(GPIO0_IR);
- if (reg & (0x80000000 >> CONFIG_SYS_GPIO_CON_DON)) {
- PRINTF("CONF_DON = HIGH\n");
- return FPGA_FAIL;
- }
- PRINTF("CONF_DON = LOW\n");
- return FPGA_SUCCESS;
-}
-
-/* writes the complete buffer to the FPGA
- writing the complete buffer in one function is much faster,
- then calling it for every bit */
-int fpga_write_fn(const void *buf, size_t len, int flush, int cookie)
-{
- size_t bytecount = 0;
- unsigned char *data = (unsigned char *) buf;
- unsigned char val = 0;
- int i;
- int len_40 = len / 40;
-
- while (bytecount < len) {
- val = data[bytecount++];
- i = 8;
- do {
- if (val & 0x01)
- FPGA_WRITE_1;
- else
- FPGA_WRITE_0;
-
- val >>= 1;
- i--;
- } while (i > 0);
-
-#ifdef CONFIG_SYS_FPGA_PROG_FEEDBACK
- if (bytecount % len_40 == 0) {
- putc('.'); /* let them know we are alive */
-#ifdef CONFIG_SYS_FPGA_CHECK_CTRLC
- if (ctrlc())
- return FPGA_FAIL;
-#endif
- }
-#endif
- }
- return FPGA_SUCCESS;
-}
-
-/* called, when programming is aborted */
-int fpga_abort_fn(int cookie)
-{
- SET_GPIO_1((CONFIG_SYS_GPIO_SEL_DPR));
- return FPGA_SUCCESS;
-}
-
-/* called, when programming was succesful */
-int fpga_post_fn(int cookie)
-{
- return fpga_abort_fn(cookie);
-}
-
-/* Note that these are pointers to code that is in Flash. They will be
- * relocated at runtime.
- */
-Altera_CYC2_Passive_Serial_fns fpga_fns = {
- fpga_pre_fn,
- fpga_config_fn,
- fpga_status_fn,
- fpga_done_fn,
- fpga_write_fn,
- fpga_abort_fn,
- fpga_post_fn
-};
-
-Altera_desc fpga[CONFIG_FPGA_COUNT] = {
- {Altera_CYC2,
- passive_serial,
- Altera_EP2C35_SIZE,
- (void *) &fpga_fns,
- NULL,
- 0}
-};
-
-/*
- * Initialize the fpga. Return 1 on success, 0 on failure.
- */
-int alpr_fpga_init(void)
-{
- int i;
-
- PRINTF("%s:%d: Initialize FPGA interface\n", __func__, __LINE__);
- fpga_init();
-
- for (i = 0; i < CONFIG_FPGA_COUNT; i++) {
- PRINTF("%s:%d: Adding fpga %d\n", __func__, __LINE__, i);
- fpga_add(fpga_altera, &fpga[i]);
- }
- return 1;
-}
-
-#endif
diff --git a/board/prodrive/alpr/init.S b/board/prodrive/alpr/init.S
deleted file mode 100644
index 7ff7a59..0000000
--- a/board/prodrive/alpr/init.S
+++ /dev/null
@@ -1,53 +0,0 @@
-/*
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <asm-offsets.h>
-#include <ppc_asm.tmpl>
-#include <asm/mmu.h>
-#include <config.h>
-#include <asm/ppc4xx.h>
-
-/**************************************************************************
- * TLB TABLE
- *
- * This table is used by the cpu boot code to setup the initial tlb
- * entries. Rather than make broad assumptions in the cpu source tree,
- * this table lets each board set things up however they like.
- *
- * Pointer to the table is returned in r1
- *
- *************************************************************************/
-
- .section .bootpg,"ax"
- .globl tlbtab
-
-tlbtab:
- tlbtab_start
- tlbentry(0xff000000, SZ_16M, 0xff000000, 1, AC_RWX | SA_IG )
- tlbentry(CONFIG_SYS_PERIPHERAL_BASE, SZ_256M, 0x40000000, 1, AC_RW | SA_IG)
- tlbentry(CONFIG_SYS_ISRAM_BASE, SZ_4K, 0x80000000, 0, AC_RWX)
- tlbentry(CONFIG_SYS_ISRAM_BASE + 0x1000, SZ_4K, 0x80001000, 0, AC_RWX)
-#ifdef CONFIG_4xx_DCACHE
- tlbentry(CONFIG_SYS_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_RWX | SA_G)
-#else
- tlbentry(CONFIG_SYS_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_RWX | SA_IG)
-#endif
-
-#ifdef CONFIG_SYS_INIT_RAM_DCACHE
- /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
- tlbentry(CONFIG_SYS_INIT_RAM_ADDR, SZ_64K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_RWX | SA_G)
-#endif
- tlbentry(CONFIG_SYS_PCI_BASE, SZ_256M, 0x00000000, 2, AC_RW | SA_IG)
-
- /* PCI */
- tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, 3, AC_RW | SA_IG)
- tlbentry(CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 3, AC_RW | SA_IG)
- tlbentry(CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 3, AC_RW | SA_IG)
-
- /* NAND */
- tlbentry(CONFIG_SYS_NAND_BASE, SZ_4K, CONFIG_SYS_NAND_BASE, 1, AC_RWX | SA_IG)
- tlbtab_end
diff --git a/board/prodrive/alpr/nand.c b/board/prodrive/alpr/nand.c
deleted file mode 100644
index ca40cea..0000000
--- a/board/prodrive/alpr/nand.c
+++ /dev/null
@@ -1,124 +0,0 @@
-/*
- * (C) Copyright 2006
- * Heiko Schocher, DENX Software Engineering, hs at denx.de
- *
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-#if defined(CONFIG_CMD_NAND)
-
-#include <asm/processor.h>
-#include <nand.h>
-
-struct alpr_ndfc_regs {
- u8 cmd[4];
- u8 addr_wait;
- u8 term;
- u8 dummy;
- u8 dummy2;
- u8 data;
-};
-
-static u8 hwctl;
-static struct alpr_ndfc_regs *alpr_ndfc = NULL;
-
-#define readb(addr) (u8)(*(volatile u8 *)(addr))
-#define writeb(d,addr) *(volatile u8 *)(addr) = ((u8)(d))
-
-/*
- * The ALPR has a NAND Flash Controller (NDFC) that handles all accesses to
- * the NAND devices. The NDFC has command, address and data registers that
- * when accessed will set up the NAND flash pins appropriately. We'll use the
- * hwcontrol function to save the configuration in a global variable.
- * We can then use this information in the read and write functions to
- * determine which NDFC register to access.
- *
- * There are 2 NAND devices on the board, a Hynix HY27US08561A (1 GByte).
- */
-static void alpr_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
-{
- struct nand_chip *this = mtd->priv;
-
- if (ctrl & NAND_CTRL_CHANGE) {
- if ( ctrl & NAND_CLE )
- hwctl |= 0x1;
- else
- hwctl &= ~0x1;
- if ( ctrl & NAND_ALE )
- hwctl |= 0x2;
- else
- hwctl &= ~0x2;
- if ( (ctrl & NAND_NCE) != NAND_NCE)
- writeb(0x00, &(alpr_ndfc->term));
- }
- if (cmd != NAND_CMD_NONE)
- writeb(cmd, this->IO_ADDR_W);
-}
-
-static u_char alpr_nand_read_byte(struct mtd_info *mtd)
-{
- return readb(&(alpr_ndfc->data));
-}
-
-static void alpr_nand_write_buf(struct mtd_info *mtd, const u_char *buf, int len)
-{
- struct nand_chip *nand = mtd->priv;
- int i;
-
- for (i = 0; i < len; i++) {
- if (hwctl & 0x1)
- /*
- * IO_ADDR_W used as CMD[i] reg to support multiple NAND
- * chips.
- */
- writeb(buf[i], nand->IO_ADDR_W);
- else if (hwctl & 0x2)
- writeb(buf[i], &(alpr_ndfc->addr_wait));
- else
- writeb(buf[i], &(alpr_ndfc->data));
- }
-}
-
-static void alpr_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len)
-{
- int i;
-
- for (i = 0; i < len; i++) {
- buf[i] = readb(&(alpr_ndfc->data));
- }
-}
-
-static int alpr_nand_dev_ready(struct mtd_info *mtd)
-{
- /*
- * Blocking read to wait for NAND to be ready
- */
- (void)readb(&(alpr_ndfc->addr_wait));
-
- /*
- * Return always true
- */
- return 1;
-}
-
-int board_nand_init(struct nand_chip *nand)
-{
- alpr_ndfc = (struct alpr_ndfc_regs *)CONFIG_SYS_NAND_BASE;
-
- nand->ecc.mode = NAND_ECC_SOFT;
-
- /* Reference hardware control function */
- nand->cmd_ctrl = alpr_nand_hwcontrol;
- nand->read_byte = alpr_nand_read_byte;
- nand->write_buf = alpr_nand_write_buf;
- nand->read_buf = alpr_nand_read_buf;
- nand->dev_ready = alpr_nand_dev_ready;
-
- return 0;
-}
-#endif
diff --git a/configs/alpr_defconfig b/configs/alpr_defconfig
deleted file mode 100644
index b7cd74d..0000000
--- a/configs/alpr_defconfig
+++ /dev/null
@@ -1,7 +0,0 @@
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_ALPR=y
-# CONFIG_CMD_LOADB is not set
-# CONFIG_CMD_LOADS is not set
-# CONFIG_CMD_SETEXPR is not set
-# CONFIG_CMD_NFS is not set
diff --git a/include/configs/alpr.h b/include/configs/alpr.h
deleted file mode 100644
index f113ebd..0000000
--- a/include/configs/alpr.h
+++ /dev/null
@@ -1,351 +0,0 @@
-/*
- * (C) Copyright 2006-2008
- * Stefan Roese, DENX Software Engineering, sr at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*-----------------------------------------------------------------------
- * High Level Configuration Options
- *----------------------------------------------------------------------*/
-#define CONFIG_ALPR 1 /* Board is ebony */
-#define CONFIG_440GX 1 /* Specifc GX support */
-#define CONFIG_440 1 /* ... PPC440 family */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#define CONFIG_LAST_STAGE_INIT 1 /* call last_stage_init() */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
-
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
-#define CONFIG_4xx_DCACHE /* Enable i- and d-cache */
-
-/*-----------------------------------------------------------------------
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CONFIG_SYS_FLASH_BASE 0xffe00000 /* start of FLASH */
-#define CONFIG_SYS_MONITOR_BASE 0xfffc0000 /* start of monitor */
-#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
-#define CONFIG_SYS_PCI_MEMSIZE 0x40000000 /* size of mapped pci memory */
-#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */
-#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */
-#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
-#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
-#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
-
-
-#define CONFIG_SYS_FPGA_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08300000)
-#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000)
-
-/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer (placed in internal SRAM)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_TEMP_STACK_OCM 1
-#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
-
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/
-
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-#define CONFIG_CONS_INDEX 2 /* Use UART1 */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_serial_clock()
-
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-/*-----------------------------------------------------------------------
- * FLASH related
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_CFI 1 /* The flash is CFI compatible */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use common CFI driver */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
-
-#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-
-#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-/*-----------------------------------------------------------------------
- * DDR SDRAM
- *----------------------------------------------------------------------*/
-#undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0 */
-#undef CONFIG_SDRAM_ECC /* enable ECC support */
-#define CONFIG_SYS_SDRAM_TABLE { \
- {(256 << 20), 13, 0x000C4001}, /* 256MB mode 3, 13x10(4)*/ \
- {(64 << 20), 12, 0x00082001}} /* 64MB mode 2, 12x9(4) */
-
-/*-----------------------------------------------------------------------
- * I2C
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (PCF8594C)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 /* EEPROM PCF8594C */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* The Philips PCF8594C has */
- /* 8 byte page write mode using */
- /* last 3 bits of the address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 40 /* and takes up to 40 msec */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run kernelx\" to boot the system;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth3\0" \
- "hostname=alpr\0" \
- "fdt_file=alpr/alpr.dtb\0" \
- "fdt_addr=400000\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath} ${init}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate} " \
- "mem=193M\0" \
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "net_nfs_fdt=tftp 200000 ${bootfile};" \
- "tftp ${fdt_addr} ${fdt_file};" \
- "run nfsargs addip addtty;" \
- "bootm 200000 - ${fdt_addr}\0" \
- "rootpath=/opt/projects/alpr/nfs_root\0" \
- "bootfile=/alpr/uImage\0" \
- "kernel_addr=fff00000\0" \
- "ramdisk_addr=fff10000\0" \
- "load=tftp 100000 /alpr/u-boot/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "ethprime=ppc_4xx_eth3\0" \
- "ethact=ppc_4xx_eth3\0" \
- "autoload=no\0" \
- "ipconfig=dhcp;setenv serverip 11.0.0.152\0" \
- "load_fpga=fpga load 0 ffe00000 10dd9a\0" \
- "mtdargs=setenv bootargs root=/dev/mtdblock6 rw " \
- "rootfstype=jffs2 init=/sbin/init\0" \
- "kernel1_mtd=nand read 200000 0 200000;run mtdargs addip addtty"\
- ";bootm 200000\0" \
- "kernel2_mtd=nand read 200000 200000 200000;run mtdargs addip " \
- "addtty;bootm 200000\0" \
- "kernel1=setenv actkernel 'kernel1';run load_fpga " \
- "kernel1_mtd\0" \
- "kernel2=setenv actkernel 'kernel2';run load_fpga " \
- "kernel2_mtd\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run kernel2"
-
-#define CONFIG_BOOTDELAY 2 /* autoboot after 5 seconds */
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0x02 /* dummy setting, no EMAC0 used */
-#define CONFIG_PHY1_ADDR 0x03 /* dummy setting, no EMAC1 used */
-#define CONFIG_PHY2_ADDR 0x01 /* PHY address for EMAC2 */
-#define CONFIG_PHY3_ADDR 0x02 /* PHY address for EMAC3 */
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#define CONFIG_HAS_ETH3
-#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
-#define CONFIG_M88E1111_PHY 1 /* needed for PHY specific setup*/
-#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_FPGA_LOADMK
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_PCI
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_ALT_MEMTEST 1 /* Enable more extensive memtest*/
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
-#define CONFIG_SYS_4xx_RESET_TYPE 0x2 /* use chip reset on this board */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-/* General PCI */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
-#define CONFIG_PCI_BOOTDELAY 1 /* enable pci bootdelay variable*/
-
-/* Board-specific PCI */
-#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */
-#define CONFIG_SYS_PCI_MASTER_INIT
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-
-/*-----------------------------------------------------------------------
- * FPGA stuff
- *-----------------------------------------------------------------------*/
-#define CONFIG_FPGA
-#define CONFIG_FPGA_ALTERA
-#define CONFIG_FPGA_CYCLON2
-#define CONFIG_SYS_FPGA_CHECK_CTRLC
-#define CONFIG_SYS_FPGA_PROG_FEEDBACK
-#define CONFIG_FPGA_COUNT 1 /* Ich habe 2 ... aber in
- Reihe geschaltet -> sollte gehen,
- aufpassen mit Datasize ist jetzt
- halt doppelt so gross ... Seite 306
- ist das mit den multiple Device in PS
- Mode erklaert ...*/
-
-/* FPGA program pin configuration */
-#define CONFIG_SYS_GPIO_CLK 18 /* FPGA clk pin (cpu output) */
-#define CONFIG_SYS_GPIO_DATA 19 /* FPGA data pin (cpu output) */
-#define CONFIG_SYS_GPIO_STATUS 20 /* FPGA status pin (cpu input) */
-#define CONFIG_SYS_GPIO_CONFIG 21 /* FPGA CONFIG pin (cpu output) */
-#define CONFIG_SYS_GPIO_CON_DON 22 /* FPGA CONFIG_DONE pin (cpu input) */
-
-#define CONFIG_SYS_GPIO_SEL_DPR 14 /* cpu output */
-#define CONFIG_SYS_GPIO_SEL_AVR 15 /* cpu output */
-#define CONFIG_SYS_GPIO_PROG_EN 23 /* cpu output */
-
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup
- *-----------------------------------------------------------------------*/
-#define CONFIG_SYS_GPIO_SHUTDOWN (0x80000000 >> 6)
-#define CONFIG_SYS_GPIO_SSD_EMPTY (0x80000000 >> 9)
-#define CONFIG_SYS_GPIO_EREADY (0x80000000 >> 26)
-#define CONFIG_SYS_GPIO_REV0 (0x80000000 >> 14)
-#define CONFIG_SYS_GPIO_REV1 (0x80000000 >> 15)
-
-/*-----------------------------------------------------------------------
- * NAND-FLASH stuff
- *-----------------------------------------------------------------------*/
-#define CONFIG_SYS_MAX_NAND_DEVICE 4
-#define CONFIG_SYS_NAND_BASE 0xF0000000 /* NAND FLASH Base Address */
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE + 0, CONFIG_SYS_NAND_BASE + 2, \
- CONFIG_SYS_NAND_BASE + 4, CONFIG_SYS_NAND_BASE + 6 }
-#define CONFIG_SYS_NAND_QUIET_TEST 1 /* don't warn upon unknown NAND flash */
-#define CONFIG_SYS_NAND_MAX_OOBFREE 2
-#define CONFIG_SYS_NAND_MAX_ECCPOS 56
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE
-
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB0AP 0x92015480
-#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0x3A000) /* BS=2MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 1 (NAND-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB1AP 0x01840380 /* TWT=3 */
-#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_NAND_BASE | 0x18000) /* BS=1MB,BU=R/W,BW=8bit */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
-#endif /* __CONFIG_H */
--
1.9.1
More information about the U-Boot
mailing list