[U-Boot] [RFC PATCH 25/28] powerpc: remove MPC8568MDS support

Masahiro Yamada yamada.masahiro at socionext.com
Thu Aug 13 12:15:43 CEST 2015


This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)

Signed-off-by: Masahiro Yamada <yamada.masahiro at socionext.com>
---

 arch/powerpc/cpu/mpc85xx/Kconfig        |   4 -
 board/freescale/mpc8568mds/Kconfig      |  12 -
 board/freescale/mpc8568mds/MAINTAINERS  |   6 -
 board/freescale/mpc8568mds/Makefile     |  13 -
 board/freescale/mpc8568mds/bcsr.c       |  61 ----
 board/freescale/mpc8568mds/bcsr.h       |  93 ------
 board/freescale/mpc8568mds/ddr.c        |  56 ----
 board/freescale/mpc8568mds/law.c        |  41 ---
 board/freescale/mpc8568mds/mpc8568mds.c | 356 -----------------------
 board/freescale/mpc8568mds/tlb.c        |  84 ------
 configs/MPC8568MDS_defconfig            |   3 -
 include/configs/MPC8568MDS.h            | 490 --------------------------------
 12 files changed, 1219 deletions(-)
 delete mode 100644 board/freescale/mpc8568mds/Kconfig
 delete mode 100644 board/freescale/mpc8568mds/MAINTAINERS
 delete mode 100644 board/freescale/mpc8568mds/Makefile
 delete mode 100644 board/freescale/mpc8568mds/bcsr.c
 delete mode 100644 board/freescale/mpc8568mds/bcsr.h
 delete mode 100644 board/freescale/mpc8568mds/ddr.c
 delete mode 100644 board/freescale/mpc8568mds/law.c
 delete mode 100644 board/freescale/mpc8568mds/mpc8568mds.c
 delete mode 100644 board/freescale/mpc8568mds/tlb.c
 delete mode 100644 configs/MPC8568MDS_defconfig
 delete mode 100644 include/configs/MPC8568MDS.h

diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig
index 9c58526..2e4edb3 100644
--- a/arch/powerpc/cpu/mpc85xx/Kconfig
+++ b/arch/powerpc/cpu/mpc85xx/Kconfig
@@ -43,9 +43,6 @@ config TARGET_P5040DS
 config TARGET_MPC8536DS
 	bool "Support MPC8536DS"
 
-config TARGET_MPC8568MDS
-	bool "Support MPC8568MDS"
-
 config TARGET_MPC8569MDS
 	bool "Support MPC8569MDS"
 
@@ -136,7 +133,6 @@ source "board/freescale/bsc9132qds/Kconfig"
 source "board/freescale/c29xpcie/Kconfig"
 source "board/freescale/corenet_ds/Kconfig"
 source "board/freescale/mpc8536ds/Kconfig"
-source "board/freescale/mpc8568mds/Kconfig"
 source "board/freescale/mpc8569mds/Kconfig"
 source "board/freescale/mpc8572ds/Kconfig"
 source "board/freescale/p1010rdb/Kconfig"
diff --git a/board/freescale/mpc8568mds/Kconfig b/board/freescale/mpc8568mds/Kconfig
deleted file mode 100644
index 4e178c5..0000000
--- a/board/freescale/mpc8568mds/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_MPC8568MDS
-
-config SYS_BOARD
-	default "mpc8568mds"
-
-config SYS_VENDOR
-	default "freescale"
-
-config SYS_CONFIG_NAME
-	default "MPC8568MDS"
-
-endif
diff --git a/board/freescale/mpc8568mds/MAINTAINERS b/board/freescale/mpc8568mds/MAINTAINERS
deleted file mode 100644
index 379d8cc..0000000
--- a/board/freescale/mpc8568mds/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-MPC8568MDS BOARD
-#M:	-
-S:	Maintained
-F:	board/freescale/mpc8568mds/
-F:	include/configs/MPC8568MDS.h
-F:	configs/MPC8568MDS_defconfig
diff --git a/board/freescale/mpc8568mds/Makefile b/board/freescale/mpc8568mds/Makefile
deleted file mode 100644
index 612fb51..0000000
--- a/board/freescale/mpc8568mds/Makefile
+++ /dev/null
@@ -1,13 +0,0 @@
-#
-# Copyright 2004-2007 Freescale Semiconductor.
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	+= mpc8568mds.o
-obj-y	+= bcsr.o
-obj-y	+= ddr.o
-obj-y	+= law.o
-obj-y	+= tlb.o
diff --git a/board/freescale/mpc8568mds/bcsr.c b/board/freescale/mpc8568mds/bcsr.c
deleted file mode 100644
index 4a6105c..0000000
--- a/board/freescale/mpc8568mds/bcsr.c
+++ /dev/null
@@ -1,61 +0,0 @@
-/*
- * Copyright 2007 Freescale Semiconductor.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-
-#include "bcsr.h"
-
-void enable_8568mds_duart(void)
-{
-	volatile uint* duart_mux	= (uint *)(CONFIG_SYS_CCSRBAR + 0xe0060);
-	volatile uint* devices		= (uint *)(CONFIG_SYS_CCSRBAR + 0xe0070);
-	volatile u8 *bcsr		= (u8 *)(CONFIG_SYS_BCSR);
-
-	*duart_mux = 0x80000000;	/* Set the mux to Duart on PMUXCR */
-	*devices  = 0;			/* Enable all peripheral devices */
-	bcsr[5] |= 0x01;		/* Enable Duart in BCSR*/
-}
-
-void enable_8568mds_flash_write(void)
-{
-	volatile u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR);
-
-	bcsr[9] |= 0x01;
-}
-
-void disable_8568mds_flash_write(void)
-{
-	volatile u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR);
-
-	bcsr[9] &= ~(0x01);
-}
-
-void enable_8568mds_qe_mdio(void)
-{
-	u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR);
-
-	bcsr[7] |= 0x01;
-}
-
-#if defined(CONFIG_UEC_ETH1) || defined(CONFIG_UEC_ETH2)
-void reset_8568mds_uccs(void)
-{
-	volatile u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR);
-
-	/* Turn off UCC1 & UCC2 */
-	out_8(&bcsr[8], in_8(&bcsr[8]) & ~BCSR_UCC1_GETH_EN);
-	out_8(&bcsr[9], in_8(&bcsr[9]) & ~BCSR_UCC2_GETH_EN);
-
-	/* Mode is RGMII, all bits clear */
-	out_8(&bcsr[11], in_8(&bcsr[11]) & ~(BCSR_UCC1_MODE_MSK |
-					     BCSR_UCC2_MODE_MSK));
-
-	/* Turn UCC1 & UCC2 on */
-	out_8(&bcsr[8], in_8(&bcsr[8]) | BCSR_UCC1_GETH_EN);
-	out_8(&bcsr[9], in_8(&bcsr[9]) | BCSR_UCC2_GETH_EN);
-}
-#endif
diff --git a/board/freescale/mpc8568mds/bcsr.h b/board/freescale/mpc8568mds/bcsr.h
deleted file mode 100644
index 215534e..0000000
--- a/board/freescale/mpc8568mds/bcsr.h
+++ /dev/null
@@ -1,93 +0,0 @@
-/*
- * Copyright 2007 Freescale Semiconductor.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __BCSR_H_
-#define __BCSR_H_
-
-#include <common.h>
-
-/* BCSR Bit definitions
-	* BCSR 0 *
-	0:3	ccb sys pll
-	4:6	cfg core pll
-	7	cfg boot seq
-
-	* BCSR 1 *
-	0:2	cfg rom lock
-	3:5	cfg host agent
-	6	PCI IO
-	7	cfg RIO size
-
-	* BCSR 2 *
-	0:4	QE PLL
-	5	QE clock
-	6	cfg PCI arbiter
-
-	* BCSR 3 *
-	0	TSEC1 reduce
-	1	TSEC2 reduce
-	2:3	TSEC1 protocol
-	4:5	TSEC2 protocol
-	6	PHY1 slave
-	7	PHY2 slave
-
-	* BCSR 4 *
-	4	clock enable
-	5	boot EPROM
-	6	GETH transactive reset
-	7	BRD write potect
-
-	* BCSR 5 *
-	1:3	Leds 1-3
-	4	UPC1 enable
-	5	UPC2 enable
-	6	UPC2 pos
-	7	RS232 enable
-
-	* BCSR 6 *
-	0	CFG ver 0
-	1	CFG ver 1
-	6	Register config led
-	7	Power on reset
-
-	* BCSR 7 *
-	2	board host mode indication
-	5	enable TSEC1 PHY
-	6	enable TSEC2 PHY
-
-	* BCSR 8 *
-	0	UCC GETH1 enable
-	1	UCC GMII enable
-	3	UCC TBI enable
-	5	UCC MII enable
-	7	Real time clock reset
-
-	* BCSR 9 *
-	0	UCC2 GETH enable
-	1	UCC2 GMII enable
-	3	UCC2 TBI enable
-	5	UCC2 MII enable
-	6	Ready only - indicate flash ready after burning
-	7	Flash write protect
-*/
-
-#define BCSR_UCC1_GETH_EN	(0x1 << 7)
-#define BCSR_UCC2_GETH_EN	(0x1 << 7)
-#define BCSR_UCC1_MODE_MSK	(0x3 << 4)
-#define BCSR_UCC2_MODE_MSK	(0x3 << 0)
-
-/*BCSR Utils functions*/
-
-void enable_8568mds_duart(void);
-void enable_8568mds_flash_write(void);
-void disable_8568mds_flash_write(void);
-void enable_8568mds_qe_mdio(void);
-
-#if defined(CONFIG_UEC_ETH1) || defined(CONFIG_UEC_ETH2)
-void reset_8568mds_uccs(void);
-#endif
-
-#endif	/* __BCSR_H_ */
diff --git a/board/freescale/mpc8568mds/ddr.c b/board/freescale/mpc8568mds/ddr.c
deleted file mode 100644
index 6db92ef..0000000
--- a/board/freescale/mpc8568mds/ddr.c
+++ /dev/null
@@ -1,56 +0,0 @@
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * Version 2 as published by the Free Software Foundation.
- */
-
-#include <common.h>
-
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-
-void fsl_ddr_board_options(memctl_options_t *popts,
-				dimm_params_t *pdimm,
-				unsigned int ctrl_num)
-{
-	/*
-	 * Factors to consider for clock adjust:
-	 *	- number of chips on bus
-	 *	- position of slot
-	 *	- DDR1 vs. DDR2?
-	 *	- ???
-	 *
-	 * This needs to be determined on a board-by-board basis.
-	 *	0110	3/4 cycle late
-	 *	0111	7/8 cycle late
-	 */
-	popts->clk_adjust = 6;
-
-	/*
-	 * Factors to consider for CPO:
-	 *	- frequency
-	 *	- ddr1 vs. ddr2
-	 */
-	popts->cpo_override = 10;
-
-	/*
-	 * Factors to consider for write data delay:
-	 *	- number of DIMMs
-	 *
-	 * 1 = 1/4 clock delay
-	 * 2 = 1/2 clock delay
-	 * 3 = 3/4 clock delay
-	 * 4 = 1   clock delay
-	 * 5 = 5/4 clock delay
-	 * 6 = 3/2 clock delay
-	 */
-	popts->write_data_delay = 3;
-
-	/*
-	 * Factors to consider for half-strength driver enable:
-	 *	- number of DIMMs installed
-	 */
-	popts->half_strength_driver_enable = 0;
-}
diff --git a/board/freescale/mpc8568mds/law.c b/board/freescale/mpc8568mds/law.c
deleted file mode 100644
index ae06966..0000000
--- a/board/freescale/mpc8568mds/law.c
+++ /dev/null
@@ -1,41 +0,0 @@
-/*
- * Copyright 2008, 2010-2011 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-/*
- * LAW(Local Access Window) configuration:
- *
- *0)   0x0000_0000   0x7fff_ffff     DDR                     2G
- *1)   0x8000_0000   0x9fff_ffff     PCI1 MEM                512MB
- *2)   0xa000_0000   0xbfff_ffff     PCIe MEM                512MB
- *-)   0xe000_0000   0xe00f_ffff     CCSR                    1M
- *3)   0xe200_0000   0xe27f_ffff     PCI1 I/O                8M
- *4)   0xe280_0000   0xe2ff_ffff     PCIe I/O                8M
- *5)   0xc000_0000   0xdfff_ffff     SRIO                    512MB
- *6.a) 0xf000_0000   0xf3ff_ffff     SDRAM                   64MB
- *6.b) 0xf800_0000   0xf800_7fff     BCSR                    32KB
- *6.c) 0xf800_8000   0xf800_ffff     PIB (CS4)		     32KB
- *6.d) 0xf801_0000   0xf801_7fff     PIB (CS5)		     32KB
- *6.e) 0xfe00_0000   0xffff_ffff     Flash                   32MB
- *
- *Notes:
- *    CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
- *    If flash is 8M at default position (last 8M), no LAW needed.
- *
- */
-
-struct law_entry law_table[] = {
-	/* LBC window - maps 256M.  That's SDRAM, BCSR, PIBs, and Flash */
-	SET_LAW(CONFIG_SYS_LBC_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/mpc8568mds/mpc8568mds.c b/board/freescale/mpc8568mds/mpc8568mds.c
deleted file mode 100644
index a5c5d9d..0000000
--- a/board/freescale/mpc8568mds/mpc8568mds.c
+++ /dev/null
@@ -1,356 +0,0 @@
-/*
- * Copyright 2007,2009-2011 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2002 Scott McNutt <smcnutt at artesyncp.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <pci.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_pci.h>
-#include <fsl_ddr_sdram.h>
-#include <asm/fsl_serdes.h>
-#include <spd_sdram.h>
-#include <i2c.h>
-#include <ioports.h>
-#include <libfdt.h>
-#include <fdt_support.h>
-
-#include "bcsr.h"
-
-const qe_iop_conf_t qe_iop_conf_tab[] = {
-	/* GETH1 */
-	{4, 10, 1, 0, 2}, /* TxD0 */
-	{4,  9, 1, 0, 2}, /* TxD1 */
-	{4,  8, 1, 0, 2}, /* TxD2 */
-	{4,  7, 1, 0, 2}, /* TxD3 */
-	{4, 23, 1, 0, 2}, /* TxD4 */
-	{4, 22, 1, 0, 2}, /* TxD5 */
-	{4, 21, 1, 0, 2}, /* TxD6 */
-	{4, 20, 1, 0, 2}, /* TxD7 */
-	{4, 15, 2, 0, 2}, /* RxD0 */
-	{4, 14, 2, 0, 2}, /* RxD1 */
-	{4, 13, 2, 0, 2}, /* RxD2 */
-	{4, 12, 2, 0, 2}, /* RxD3 */
-	{4, 29, 2, 0, 2}, /* RxD4 */
-	{4, 28, 2, 0, 2}, /* RxD5 */
-	{4, 27, 2, 0, 2}, /* RxD6 */
-	{4, 26, 2, 0, 2}, /* RxD7 */
-	{4, 11, 1, 0, 2}, /* TX_EN */
-	{4, 24, 1, 0, 2}, /* TX_ER */
-	{4, 16, 2, 0, 2}, /* RX_DV */
-	{4, 30, 2, 0, 2}, /* RX_ER */
-	{4, 17, 2, 0, 2}, /* RX_CLK */
-	{4, 19, 1, 0, 2}, /* GTX_CLK */
-	{1, 31, 2, 0, 3}, /* GTX125 */
-
-	/* GETH2 */
-	{5, 10, 1, 0, 2}, /* TxD0 */
-	{5,  9, 1, 0, 2}, /* TxD1 */
-	{5,  8, 1, 0, 2}, /* TxD2 */
-	{5,  7, 1, 0, 2}, /* TxD3 */
-	{5, 23, 1, 0, 2}, /* TxD4 */
-	{5, 22, 1, 0, 2}, /* TxD5 */
-	{5, 21, 1, 0, 2}, /* TxD6 */
-	{5, 20, 1, 0, 2}, /* TxD7 */
-	{5, 15, 2, 0, 2}, /* RxD0 */
-	{5, 14, 2, 0, 2}, /* RxD1 */
-	{5, 13, 2, 0, 2}, /* RxD2 */
-	{5, 12, 2, 0, 2}, /* RxD3 */
-	{5, 29, 2, 0, 2}, /* RxD4 */
-	{5, 28, 2, 0, 2}, /* RxD5 */
-	{5, 27, 2, 0, 3}, /* RxD6 */
-	{5, 26, 2, 0, 2}, /* RxD7 */
-	{5, 11, 1, 0, 2}, /* TX_EN */
-	{5, 24, 1, 0, 2}, /* TX_ER */
-	{5, 16, 2, 0, 2}, /* RX_DV */
-	{5, 30, 2, 0, 2}, /* RX_ER */
-	{5, 17, 2, 0, 2}, /* RX_CLK */
-	{5, 19, 1, 0, 2}, /* GTX_CLK */
-	{1, 31, 2, 0, 3}, /* GTX125 */
-	{4,  6, 3, 0, 2}, /* MDIO */
-	{4,  5, 1, 0, 2}, /* MDC */
-
-	/* UART1 */
-	{2, 0, 1, 0, 2}, /* UART_SOUT1 */
-	{2, 1, 1, 0, 2}, /* UART_RTS1 */
-	{2, 2, 2, 0, 2}, /* UART_CTS1 */
-	{2, 3, 2, 0, 2}, /* UART_SIN1 */
-
-	{0,  0, 0, 0, QE_IOP_TAB_END}, /* END of table */
-};
-
-void local_bus_init(void);
-
-int board_early_init_f (void)
-{
-	/*
-	 * Initialize local bus.
-	 */
-	local_bus_init ();
-
-	enable_8568mds_duart();
-	enable_8568mds_flash_write();
-#if defined(CONFIG_UEC_ETH1) || defined(CONFIG_UEC_ETH2)
-	reset_8568mds_uccs();
-#endif
-#if defined(CONFIG_QE) && !defined(CONFIG_eTSEC_MDIO_BUS)
-	enable_8568mds_qe_mdio();
-#endif
-
-#ifdef CONFIG_SYS_I2C2_OFFSET
-	/* Enable I2C2_SCL and I2C2_SDA */
-	volatile struct par_io *port_c;
-	port_c = (struct par_io*)(CONFIG_SYS_IMMR + 0xe0140);
-	port_c->cpdir2 |= 0x0f000000;
-	port_c->cppar2 &= ~0x0f000000;
-	port_c->cppar2 |= 0x0a000000;
-#endif
-
-	return 0;
-}
-
-int checkboard (void)
-{
-	printf ("Board: 8568 MDS\n");
-
-	return 0;
-}
-
-/*
- * Initialize Local Bus
- */
-void
-local_bus_init(void)
-{
-	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-	volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
-
-	uint clkdiv;
-	sys_info_t sysinfo;
-
-	get_sys_info(&sysinfo);
-	clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2;
-
-	gur->lbiuiplldcr1 = 0x00078080;
-	if (clkdiv == 16) {
-		gur->lbiuiplldcr0 = 0x7c0f1bf0;
-	} else if (clkdiv == 8) {
-		gur->lbiuiplldcr0 = 0x6c0f1bf0;
-	} else if (clkdiv == 4) {
-		gur->lbiuiplldcr0 = 0x5c0f1bf0;
-	}
-
-	lbc->lcrr |= 0x00030000;
-
-	asm("sync;isync;msync");
-}
-
-/*
- * Initialize SDRAM memory on the Local Bus.
- */
-void lbc_sdram_init(void)
-{
-#if defined(CONFIG_SYS_OR2_PRELIM) && defined(CONFIG_SYS_BR2_PRELIM)
-
-	uint idx;
-	volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
-	uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
-	uint lsdmr_common;
-
-	puts("LBC SDRAM: ");
-	print_size(CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024,
-		   "\n       ");
-
-	/*
-	 * Setup SDRAM Base and Option Registers
-	 */
-	set_lbc_or(2, CONFIG_SYS_OR2_PRELIM);
-	set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
-	asm("msync");
-
-	lbc->lbcr = CONFIG_SYS_LBC_LBCR;
-	asm("msync");
-
-	lbc->lsrt = CONFIG_SYS_LBC_LSRT;
-	lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
-	asm("msync");
-
-	/*
-	 * MPC8568 uses "new" 15-16 style addressing.
-	 */
-	lsdmr_common = CONFIG_SYS_LBC_LSDMR_COMMON;
-	lsdmr_common |= LSDMR_BSMA1516;
-
-	/*
-	 * Issue PRECHARGE ALL command.
-	 */
-	lbc->lsdmr = lsdmr_common | LSDMR_OP_PCHALL;
-	asm("sync;msync");
-	*sdram_addr = 0xff;
-	ppcDcbf((unsigned long) sdram_addr);
-	udelay(100);
-
-	/*
-	 * Issue 8 AUTO REFRESH commands.
-	 */
-	for (idx = 0; idx < 8; idx++) {
-		lbc->lsdmr = lsdmr_common | LSDMR_OP_ARFRSH;
-		asm("sync;msync");
-		*sdram_addr = 0xff;
-		ppcDcbf((unsigned long) sdram_addr);
-		udelay(100);
-	}
-
-	/*
-	 * Issue 8 MODE-set command.
-	 */
-	lbc->lsdmr = lsdmr_common | LSDMR_OP_MRW;
-	asm("sync;msync");
-	*sdram_addr = 0xff;
-	ppcDcbf((unsigned long) sdram_addr);
-	udelay(100);
-
-	/*
-	 * Issue NORMAL OP command.
-	 */
-	lbc->lsdmr = lsdmr_common | LSDMR_OP_NORMAL;
-	asm("sync;msync");
-	*sdram_addr = 0xff;
-	ppcDcbf((unsigned long) sdram_addr);
-	udelay(200);    /* Overkill. Must wait > 200 bus cycles */
-
-#endif	/* enable SDRAM init */
-}
-
-#if defined(CONFIG_PCI)
-#ifndef CONFIG_PCI_PNP
-static struct pci_config_table pci_mpc8568mds_config_table[] = {
-	{
-	 PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
-	 pci_cfgfunc_config_device,
-	 {PCI_ENET0_IOADDR,
-	  PCI_ENET0_MEMADDR,
-	  PCI_COMMON_MEMORY | PCI_COMMAND_MASTER}
-	 },
-	{}
-};
-#endif
-
-static struct pci_controller pci1_hose;
-#endif	/* CONFIG_PCI */
-
-/*
- * pib_init() -- Initialize the PCA9555 IO expander on the PIB board
- */
-void
-pib_init(void)
-{
-	u8 val8, orig_i2c_bus;
-	/*
-	 * Assign PIB PMC2/3 to PCI bus
-	 */
-
-	/*switch temporarily to I2C bus #2 */
-	orig_i2c_bus = i2c_get_bus_num();
-	i2c_set_bus_num(1);
-
-	val8 = 0x00;
-	i2c_write(0x23, 0x6, 1, &val8, 1);
-	i2c_write(0x23, 0x7, 1, &val8, 1);
-	val8 = 0xff;
-	i2c_write(0x23, 0x2, 1, &val8, 1);
-	i2c_write(0x23, 0x3, 1, &val8, 1);
-
-	val8 = 0x00;
-	i2c_write(0x26, 0x6, 1, &val8, 1);
-	val8 = 0x34;
-	i2c_write(0x26, 0x7, 1, &val8, 1);
-	val8 = 0xf9;
-	i2c_write(0x26, 0x2, 1, &val8, 1);
-	val8 = 0xff;
-	i2c_write(0x26, 0x3, 1, &val8, 1);
-
-	val8 = 0x00;
-	i2c_write(0x27, 0x6, 1, &val8, 1);
-	i2c_write(0x27, 0x7, 1, &val8, 1);
-	val8 = 0xff;
-	i2c_write(0x27, 0x2, 1, &val8, 1);
-	val8 = 0xef;
-	i2c_write(0x27, 0x3, 1, &val8, 1);
-
-	asm("eieio");
-	i2c_set_bus_num(orig_i2c_bus);
-}
-
-#ifdef CONFIG_PCI
-void pci_init_board(void)
-{
-	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-	int first_free_busno = 0;
-#ifdef CONFIG_PCI1
-	struct fsl_pci_info pci_info;
-	u32 devdisr, pordevsr, io_sel;
-	u32 porpllsr, pci_agent, pci_speed, pci_32, pci_arb, pci_clk_sel;
-
-	devdisr = in_be32(&gur->devdisr);
-	pordevsr = in_be32(&gur->pordevsr);
-	porpllsr = in_be32(&gur->porpllsr);
-	io_sel = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
-
-	debug ("   pci_init_board: devdisr=%x, io_sel=%x\n", devdisr, io_sel);
-
-	pci_speed = 66666000;
-	pci_32 = 1;
-	pci_arb = pordevsr & MPC85xx_PORDEVSR_PCI1_ARB;
-	pci_clk_sel = porpllsr & MPC85xx_PORDEVSR_PCI1_SPD;
-
-	if (!(devdisr & MPC85xx_DEVDISR_PCI1)) {
-		SET_STD_PCI_INFO(pci_info, 1);
-		set_next_law(pci_info.mem_phys,
-			law_size_bits(pci_info.mem_size), pci_info.law);
-		set_next_law(pci_info.io_phys,
-			law_size_bits(pci_info.io_size), pci_info.law);
-
-		pci_agent = fsl_setup_hose(&pci1_hose, pci_info.regs);
-		printf("PCI: %d bit, %s MHz, %s, %s, %s (base address %lx)\n",
-			(pci_32) ? 32 : 64,
-			(pci_speed == 33333000) ? "33" :
-			(pci_speed == 66666000) ? "66" : "unknown",
-			pci_clk_sel ? "sync" : "async",
-			pci_agent ? "agent" : "host",
-			pci_arb ? "arbiter" : "external-arbiter",
-			pci_info.regs);
-
-#ifndef CONFIG_PCI_PNP
-		pci1_hose.config_table = pci_mpc8568mds_config_table;
-#endif
-		first_free_busno = fsl_pci_init_port(&pci_info,
-					&pci1_hose, first_free_busno);
-	} else {
-		printf("PCI: disabled\n");
-	}
-
-	puts("\n");
-#else
-	setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCI1); /* disable */
-#endif
-
-	fsl_pcie_init_board(first_free_busno);
-}
-#endif /* CONFIG_PCI */
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, bd_t *bd)
-{
-	ft_cpu_setup(blob, bd);
-
-	FT_FSL_PCI_SETUP;
-
-	return 0;
-}
-#endif
diff --git a/board/freescale/mpc8568mds/tlb.c b/board/freescale/mpc8568mds/tlb.c
deleted file mode 100644
index b5e2fec..0000000
--- a/board/freescale/mpc8568mds/tlb.c
+++ /dev/null
@@ -1,84 +0,0 @@
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
-	/* TLB 0 - for temp stack in cache */
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-
-	/* TLB 1 Initializations */
-	/*
-	 * TLBe 0:	16M	Non-cacheable, guarded
-	 * 0xff000000	16M	FLASH (upper half)
-	 * Out of reset this entry is only 4K.
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE + 0x1000000, CONFIG_SYS_FLASH_BASE + 0x1000000,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 0, BOOKE_PAGESZ_16M, 1),
-
-	/*
-	 * TLBe 1:	16M	Non-cacheable, guarded
-	 * 0xfe000000	16M	FLASH (lower half)
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 1, BOOKE_PAGESZ_16M, 1),
-
-	/*
-	 * TLBe 2:	1G	Non-cacheable, guarded
-	 * 0x80000000	512M	PCI1 MEM
-	 * 0xa0000000	512M	PCIe MEM
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_VIRT, CONFIG_SYS_PCI1_MEM_PHYS,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 2, BOOKE_PAGESZ_1G, 1),
-
-	/*
-	 * TLBe 3:	64M	Non-cacheable, guarded
-	 * 0xe000_0000	1M	CCSRBAR
-	 * 0xe200_0000	8M	PCI1 IO
-	 * 0xe280_0000	8M	PCIe IO
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 3, BOOKE_PAGESZ_64M, 1),
-
-	/*
-	 * TLBe 4:	64M	Cacheable, non-guarded
-	 * 0xf000_0000	64M	LBC SDRAM
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_LBC_SDRAM_BASE, CONFIG_SYS_LBC_SDRAM_BASE,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 4, BOOKE_PAGESZ_64M, 1),
-
-	/*
-	 * TLBe 5:	256K	Non-cacheable, guarded
-	 * 0xf8000000	32K BCSR
-	 * 0xf8008000	32K PIB (CS4)
-	 * 0xf8010000	32K PIB (CS5)
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_BCSR_BASE, CONFIG_SYS_BCSR_BASE,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 5, BOOKE_PAGESZ_256K, 1),
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/configs/MPC8568MDS_defconfig b/configs/MPC8568MDS_defconfig
deleted file mode 100644
index ac0ec8c..0000000
--- a/configs/MPC8568MDS_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC85xx=y
-CONFIG_TARGET_MPC8568MDS=y
diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
deleted file mode 100644
index 05e5a3d..0000000
--- a/include/configs/MPC8568MDS.h
+++ /dev/null
@@ -1,490 +0,0 @@
-/*
- * Copyright 2004-2007, 2010-2011 Freescale Semiconductor.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * mpc8568mds board configuration file
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE		1	/* BOOKE */
-#define CONFIG_E500		1	/* BOOKE e500 family */
-#define CONFIG_MPC8568		1	/* MPC8568 specific */
-#define CONFIG_MPC8568MDS	1	/* MPC8568MDS board specific */
-
-#define	CONFIG_SYS_TEXT_BASE	0xfff80000
-
-#define CONFIG_SYS_SRIO
-#define CONFIG_SRIO1			/* SRIO port 1 */
-
-#define CONFIG_PCI		1	/* Enable PCI/PCIE */
-#define CONFIG_PCI1		1	/* PCI controller */
-#define CONFIG_PCIE1		1	/* PCIE controller */
-#define CONFIG_FSL_PCI_INIT	1	/* use common fsl pci init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
-#define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
-#define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
-#define CONFIG_TSEC_ENET		/* tsec ethernet support */
-#define CONFIG_QE			/* Enable QE */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_clock_freq(void);
-#endif						  /*Replace a call to get_clock_freq (after it is implemented)*/
-#define CONFIG_SYS_CLK_FREQ	66000000 /*TODO: restore if wanting to read from BCSR: get_clock_freq()*/ /* sysclk for MPC85xx */
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE				/* toggle L2 cache	*/
-#define CONFIG_BTB				/* toggle branch predition */
-
-/*
- * Only possible on E500 Version 2 or newer cores.
- */
-#define CONFIG_ENABLE_36BIT_PHYS	1
-
-
-#define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
-
-#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x00400000
-
-#define CONFIG_SYS_CCSRBAR		0xe0000000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
-
-/* DDR Setup */
-#define CONFIG_SYS_FSL_DDR2
-#undef CONFIG_FSL_DDR_INTERACTIVE
-#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_SPD
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
-
-#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_NUM_DDR_CONTROLLERS	1
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-
-/* I2C addresses of SPD EEPROMs */
-#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
-
-/* Make sure required options are set */
-#ifndef CONFIG_SPD_EEPROM
-#error ("CONFIG_SPD_EEPROM is required")
-#endif
-
-#undef CONFIG_CLOCKS_IN_MHZ
-
-/*
- * Local Bus Definitions
- */
-
-/*
- * FLASH on the Local Bus
- * Two banks, 8M each, using the CFI driver.
- * Boot from BR0/OR0 bank at 0xff00_0000
- * Alternate BR1/OR1 bank at 0xff80_0000
- *
- * BR0, BR1:
- *    Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
- *    Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
- *    Port Size = 16 bits = BRx[19:20] = 10
- *    Use GPCM = BRx[24:26] = 000
- *    Valid = BRx[31] = 1
- *
- * 0    4    8    12   16   20   24   28
- * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001    BR0
- * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001    BR1
- *
- * OR0, OR1:
- *    Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
- *    Reserved ORx[17:18] = 11, confusion here?
- *    CSNT = ORx[20] = 1
- *    ACS = half cycle delay = ORx[21:22] = 11
- *    SCY = 6 = ORx[24:27] = 0110
- *    TRLX = use relaxed timing = ORx[29] = 1
- *    EAD = use external address latch delay = OR[31] = 1
- *
- * 0    4    8    12   16   20   24   28
- * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65    ORx
- */
-#define CONFIG_SYS_BCSR_BASE		0xf8000000
-
-#define CONFIG_SYS_FLASH_BASE		0xfe000000	/* start of FLASH 32M */
-
-/*Chip select 0 - Flash*/
-#define CONFIG_SYS_BR0_PRELIM		0xfe001001
-#define	CONFIG_SYS_OR0_PRELIM		0xfe006ff7
-
-/*Chip slelect 1 - BCSR*/
-#define CONFIG_SYS_BR1_PRELIM		0xf8000801
-#define	CONFIG_SYS_OR1_PRELIM		0xffffe9f7
-
-/*#define CONFIG_SYS_FLASH_BANKS_LIST	{0xff800000, CONFIG_SYS_FLASH_BASE} */
-#define CONFIG_SYS_MAX_FLASH_BANKS		1		/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT		512		/* sectors per device */
-#undef	CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-
-/*
- * SDRAM on the LocalBus
- */
-#define CONFIG_SYS_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM	 */
-#define CONFIG_SYS_LBC_SDRAM_SIZE	64			/* LBC SDRAM is 64MB */
-
-
-/*Chip select 2 - SDRAM*/
-#define CONFIG_SYS_BR2_PRELIM      0xf0001861
-#define CONFIG_SYS_OR2_PRELIM		0xfc006901
-
-#define CONFIG_SYS_LBC_LCRR		0x00030004	/* LB clock ratio reg */
-#define CONFIG_SYS_LBC_LBCR		0x00000000	/* LB config reg */
-#define CONFIG_SYS_LBC_LSRT		0x20000000	/* LB sdram refresh timer */
-#define CONFIG_SYS_LBC_MRTPR		0x00000000	/* LB refresh timer prescal*/
-
-/*
- * Common settings for all Local Bus SDRAM commands.
- * At run time, either BSMA1516 (for CPU 1.1)
- *                  or BSMA1617 (for CPU 1.0) (old)
- * is OR'ed in too.
- */
-#define CONFIG_SYS_LBC_LSDMR_COMMON	( LSDMR_RFCR16		\
-				| LSDMR_PRETOACT7	\
-				| LSDMR_ACTTORW7	\
-				| LSDMR_BL8		\
-				| LSDMR_WRC4		\
-				| LSDMR_CL3		\
-				| LSDMR_RFEN		\
-				)
-
-/*
- * The bcsr registers are connected to CS3 on MDS.
- * The new memory map places bcsr at 0xf8000000.
- *
- * For BR3, need:
- *    Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
- *    port-size = 8-bits  = BR[19:20] = 01
- *    no parity checking  = BR[21:22] = 00
- *    GPMC for MSEL       = BR[24:26] = 000
- *    Valid               = BR[31]    = 1
- *
- * 0    4    8    12   16   20   24   28
- * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
- *
- * For OR3, need:
- *    1 MB mask for AM,   OR[0:16]  = 1111 1111 1111 0000 0
- *    disable buffer ctrl OR[19]    = 0
- *    CSNT                OR[20]    = 1
- *    ACS                 OR[21:22] = 11
- *    XACS                OR[23]    = 1
- *    SCY 15 wait states  OR[24:27] = 1111	max is suboptimal but safe
- *    SETA                OR[28]    = 0
- *    TRLX                OR[29]    = 1
- *    EHTR                OR[30]    = 1
- *    EAD extra time      OR[31]    = 1
- *
- * 0    4    8    12   16   20   24   28
- * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
- */
-#define CONFIG_SYS_BCSR (0xf8000000)
-
-/*Chip slelect 4 - PIB*/
-#define CONFIG_SYS_BR4_PRELIM   0xf8008801
-#define CONFIG_SYS_OR4_PRELIM   0xffffe9f7
-
-/*Chip select 5 - PIB*/
-#define CONFIG_SYS_BR5_PRELIM	 0xf8010801
-#define CONFIG_SYS_OR5_PRELIM	 0xffff69f7
-
-#define CONFIG_SYS_INIT_RAM_LOCK	1
-#define CONFIG_SYS_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x4000	    /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserved for malloc */
-
-/* Serial Port */
-#define CONFIG_CONS_INDEX		1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE    1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR+0x4600)
-
-/* Use the HUSH parser*/
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef  CONFIG_SYS_HUSH_PARSER
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT		1
-#define CONFIG_OF_BOARD_SETUP		1
-#define CONFIG_OF_STDOUT_VIA_ALIAS	1
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x52
-
-/*
- * General PCI
- * Memory Addresses are mapped 1-1. I/O is mapped from 0
- */
-#define CONFIG_SYS_PCI1_MEM_VIRT	0x80000000
-#define CONFIG_SYS_PCI1_MEM_BUS	0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS	0x80000000
-#define CONFIG_SYS_PCI1_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCI1_IO_VIRT	0xe2000000
-#define CONFIG_SYS_PCI1_IO_BUS	0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS	0xe2000000
-#define CONFIG_SYS_PCI1_IO_SIZE	0x00800000	/* 8M */
-
-#define CONFIG_SYS_PCIE1_NAME		"Slot"
-#define CONFIG_SYS_PCIE1_MEM_VIRT	0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_BUS	0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT	0xe2800000
-#define CONFIG_SYS_PCIE1_IO_BUS	0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS	0xe2800000
-#define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000	/* 8M */
-
-#define CONFIG_SYS_SRIO1_MEM_VIRT	0xC0000000
-#define CONFIG_SYS_SRIO1_MEM_BUS	0xC0000000
-#define CONFIG_SYS_SRIO1_MEM_PHYS	CONFIG_SYS_SRIO1_MEM_BUS
-#define CONFIG_SYS_SRIO1_MEM_SIZE	0x20000000	/* 512M */
-
-#ifdef CONFIG_QE
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#ifndef CONFIG_TSEC_ENET
-#define CONFIG_ETHPRIME         "UEC0"
-#endif
-#define CONFIG_PHY_MODE_NEED_CHANGE
-#define CONFIG_eTSEC_MDIO_BUS
-
-#ifdef CONFIG_eTSEC_MDIO_BUS
-#define CONFIG_MIIM_ADDRESS	0xE0024520
-#endif
-
-#define CONFIG_UEC_ETH1         /* GETH1 */
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM        0       /* UCC1 */
-#define CONFIG_SYS_UEC1_RX_CLK         QE_CLK_NONE
-#define CONFIG_SYS_UEC1_TX_CLK         QE_CLK16
-#define CONFIG_SYS_UEC1_ETH_TYPE       GIGA_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR       7
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
-#endif
-
-#define CONFIG_UEC_ETH2         /* GETH2 */
-
-#ifdef CONFIG_UEC_ETH2
-#define CONFIG_SYS_UEC2_UCC_NUM        1       /* UCC2 */
-#define CONFIG_SYS_UEC2_RX_CLK         QE_CLK_NONE
-#define CONFIG_SYS_UEC2_TX_CLK         QE_CLK16
-#define CONFIG_SYS_UEC2_ETH_TYPE       GIGA_ETH
-#define CONFIG_SYS_UEC2_PHY_ADDR       1
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
-#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
-#endif
-#endif /* CONFIG_QE */
-
-#if defined(CONFIG_PCI)
-
-#define CONFIG_PCI_PNP			/* do pci plug-and-play */
-
-#undef CONFIG_EEPRO100
-#undef CONFIG_TULIP
-
-#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
-
-#endif	/* CONFIG_PCI */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_MII		1	/* MII PHY management */
-#define CONFIG_TSEC1	1
-#define CONFIG_TSEC1_NAME	"eTSEC0"
-#define CONFIG_TSEC2	1
-#define CONFIG_TSEC2_NAME	"eTSEC1"
-
-#define TSEC1_PHY_ADDR		2
-#define TSEC2_PHY_ADDR		3
-
-#define TSEC1_PHYIDX		0
-#define TSEC2_PHYIDX		0
-
-#define TSEC1_FLAGS		TSEC_GIGABIT
-#define TSEC2_FLAGS		TSEC_GIGABIT
-
-/* Options are: eTSEC[0-1] */
-#define CONFIG_ETHPRIME		"eTSEC0"
-
-#endif	/* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0x40000)
-#define CONFIG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
-#define CONFIG_ENV_SIZE		0x2000
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-    #define CONFIG_CMD_PCI
-#endif
-
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
-#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
-#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
-#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE	256			/* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-/* The mac addresses for all ethernet interface */
-#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#define CONFIG_HAS_ETH3
-#endif
-
-#define CONFIG_IPADDR    192.168.1.253
-
-#define CONFIG_HOSTNAME  unknown
-#define CONFIG_ROOTPATH  "/nfsroot"
-#define CONFIG_BOOTFILE  "your.uImage"
-
-#define CONFIG_SERVERIP  192.168.1.1
-#define CONFIG_GATEWAYIP 192.168.1.1
-#define CONFIG_NETMASK   255.255.255.0
-
-#define CONFIG_LOADADDR  200000   /*default location for tftp and bootm*/
-
-#define CONFIG_BOOTDELAY 10       /* -1 disables auto-boot */
-#undef  CONFIG_BOOTARGS           /* the boot command will set bootargs*/
-
-#define CONFIG_BAUDRATE	115200
-
-#define	CONFIG_EXTRA_ENV_SETTINGS				        \
-   "netdev=eth0\0"                                                      \
-   "consoledev=ttyS0\0"                                                 \
-   "ramdiskaddr=600000\0"                                               \
-   "ramdiskfile=your.ramdisk.u-boot\0"					\
-   "fdtaddr=400000\0"							\
-   "fdtfile=your.fdt.dtb\0"						\
-   "nfsargs=setenv bootargs root=/dev/nfs rw "				\
-      "nfsroot=$serverip:$rootpath "					\
-      "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
-      "console=$consoledev,$baudrate $othbootargs\0"			\
-   "ramargs=setenv bootargs root=/dev/ram rw "				\
-      "console=$consoledev,$baudrate $othbootargs\0"			\
-
-
-#define CONFIG_NFSBOOTCOMMAND	                                        \
-   "run nfsargs;"							\
-   "tftp $loadaddr $bootfile;"                                          \
-   "tftp $fdtaddr $fdtfile;"						\
-   "bootm $loadaddr - $fdtaddr"
-
-
-#define CONFIG_RAMBOOTCOMMAND \
-   "run ramargs;"							\
-   "tftp $ramdiskaddr $ramdiskfile;"                                    \
-   "tftp $loadaddr $bootfile;"                                          \
-   "bootm $loadaddr $ramdiskaddr"
-
-#define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
-
-#endif	/* __CONFIG_H */
-- 
1.9.1




More information about the U-Boot mailing list