[U-Boot] [PATCH v7 3/5] nand: lpc32xx: add ECC layout for small page NAND

slemieux.tyco at gmail.com slemieux.tyco at gmail.com
Thu Aug 13 21:40:21 CEST 2015


From: Sylvain Lemieux <slemieux at tycoint.com>

Incorporate ECC layout for small page NAND from legacy LPCLinux NXP BSP.
The code taken from the legacy patch is:
- lpc32xx SLC NAND driver (ECC layout for small page)

This layout is matching the lpc32xx NAND SLC Linux Kernel driver.

Signed-off-by: Sylvain Lemieux <slemieux at tycoint.com>
---
Changes from v6 to v7:
* No changes; patch context updated.

Changes from v5 to v6:
* Updated comment regarding default OOB layout.

Changes from v4 to v5:
* No changes; patch context updated.

Changes from v3 to v4:
* No changes.

Changes from v2 to v3:
* No changes; patch context updated.

Changes from v1 to v2:
* Move ECC layout for small page NAND into a separate patch.

The legacy BSP patch (u-boot-2009.03_lpc32x0-v1.07.patch.tar.bz2)
was downloaded from the LPCLinux Web site.

 drivers/mtd/nand/lpc32xx_nand_slc.c | 18 +++++++++++++++++-
 1 file changed, 17 insertions(+), 1 deletion(-)

diff --git a/drivers/mtd/nand/lpc32xx_nand_slc.c b/drivers/mtd/nand/lpc32xx_nand_slc.c
index dbb95d9..2e5f139 100644
--- a/drivers/mtd/nand/lpc32xx_nand_slc.c
+++ b/drivers/mtd/nand/lpc32xx_nand_slc.c
@@ -75,6 +75,19 @@ struct lpc32xx_nand_slc_regs {
 #define TAC_R_HOLD(n)		(max_t(uint32_t, (n), 0xF) << 4)
 #define TAC_R_SETUP(n)		(max_t(uint32_t, (n), 0xF) << 0)
 
+/* NAND ECC Layout for small page NAND devices
+ * Note: For large page devices, the default layouts are used. */
+static struct nand_ecclayout lpc32xx_nand_oob_16 = {
+	.eccbytes = 6,
+	.eccpos = {10, 11, 12, 13, 14, 15},
+	.oobfree = {
+		{.offset = 0,
+		 . length = 4},
+		{.offset = 6,
+		 . length = 4}
+		}
+};
+
 #if defined(CONFIG_DMA_LPC32XX)
 #define ECCSTEPS	(CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE)
 
@@ -563,13 +576,16 @@ int board_nand_init(struct nand_chip *lpc32xx_chip)
 #endif
 
 	/*
-	 * Use default ECC layout, but these values are predefined
+	 * These values are predefined
 	 * for both small and large page NAND flash devices.
 	 */
 	lpc32xx_chip->ecc.size     = CONFIG_SYS_NAND_ECCSIZE;
 	lpc32xx_chip->ecc.bytes    = CONFIG_SYS_NAND_ECCBYTES;
 	lpc32xx_chip->ecc.strength = 1;
 
+	if (CONFIG_SYS_NAND_PAGE_SIZE != NAND_LARGE_BLOCK_PAGE_SIZE)
+		lpc32xx_chip->ecc.layout = &lpc32xx_nand_oob_16;
+
 #if defined(CONFIG_SYS_NAND_USE_FLASH_BBT)
 	lpc32xx_chip->bbt_options |= NAND_BBT_USE_FLASH;
 #endif
-- 
1.8.3.1



More information about the U-Boot mailing list