[U-Boot] [PATCH 1/3] ARM: at91: sama5: move the sd/mmc env config to at91-sama5_common.h
Josh Wu
josh.wu at atmel.com
Wed Aug 19 10:10:57 CEST 2015
Hi, Andreas
On 8/19/2015 3:40 PM, Andreas Bießmann wrote:
> Hi Josh,
>
> On 07/07/2015 01:08 PM, Josh Wu wrote:
>> As almost all sama5 sd/mmc env configurations are same, so move them to
>> at91-sama5_common.h.
>>
>> Also we define a KERNEL_DTB_FILE_NAME as dtb file name for different
>> board.
> I don't like this new variable. At least we need some documentation in
> README or even better Kconfig for it!
> But I think we do not need it, let's see ...
>
>> Signed-off-by: Josh Wu <josh.wu at atmel.com>
>> ---
>> Hi,
>>
>> Those patches depends on the patch: http://patchwork.ozlabs.org/patch/485339/
>>
>> Best Regards,
>> Josh Wu
>>
>> include/configs/at91-sama5_common.h | 17 +++++++++++++++++
>> include/configs/sama5d3_xplained.h | 12 +++---------
>> include/configs/sama5d3xek.h | 10 +---------
>> include/configs/sama5d4_xplained.h | 20 +++-----------------
>> include/configs/sama5d4ek.h | 18 +++---------------
>> 5 files changed, 27 insertions(+), 50 deletions(-)
>>
>> diff --git a/include/configs/at91-sama5_common.h b/include/configs/at91-sama5_common.h
>> index 9289964..99fa0b1 100644
>> --- a/include/configs/at91-sama5_common.h
>> +++ b/include/configs/at91-sama5_common.h
>> @@ -56,6 +56,23 @@
>> #define CONFIG_CMD_DHCP
>>
>> #ifdef CONFIG_SYS_USE_MMC
>> +/* u-boot env in sd/mmc card */
>> +#define CONFIG_ENV_IS_IN_FAT
>> +#define CONFIG_FAT_WRITE
>> +#define FAT_ENV_INTERFACE "mmc"
>> +#define FAT_ENV_DEVICE_AND_PART "0"
>> +#define FAT_ENV_FILE "uboot.env"
>> +#define CONFIG_ENV_SIZE 0x4000
>> +
>> +#ifdef KERNEL_DTB_FILE_NAME
>> +#define CONFIG_BOOT_DTB_COMMAND "fatload mmc 0:1 0x21000000 " KERNEL_DTB_FILE_NAME "; "
>> +#else
>> +#define CONFIG_BOOT_DTB_COMMAND "fatload mmc 0:1 0x21000000 ${ek_name}.dtb; "
>> +#endif
>> +
>> +#define CONFIG_BOOTCOMMAND CONFIG_BOOT_DTB_COMMAND \
>> + "fatload mmc 0:1 0x22000000 zImage; " \
>> + "bootz 0x22000000 - 0x21000000"
>> #define CONFIG_BOOTARGS \
>> "console=ttyS0,115200 earlyprintk " \
>> "root=/dev/mmcblk0p2 rw rootwait"
>> diff --git a/include/configs/sama5d3_xplained.h b/include/configs/sama5d3_xplained.h
>> index c4141a0..e5de24b 100644
>> --- a/include/configs/sama5d3_xplained.h
>> +++ b/include/configs/sama5d3_xplained.h
>> @@ -13,6 +13,8 @@
>> /* No NOR flash, this definition should put before common header */
>> #define CONFIG_SYS_NO_FLASH
>>
>> +#define KERNEL_DTB_FILE_NAME "at91-sama5d3_xplained.dtb"
> This is "at91-" + $CONFIG_SYS_BOARD + ".dtb"
>
>> +
>> #include "at91-sama5_common.h"
>>
>> /* serial console */
>> @@ -124,15 +126,7 @@
>> "nand read 0x22000000 0x200000 0x600000;" \
>> "bootz 0x22000000 - 0x21000000"
>> #elif CONFIG_SYS_USE_MMC
>> -/* bootstrap + u-boot + env in sd card */
>> -#define CONFIG_ENV_IS_IN_FAT
>> -#define FAT_ENV_INTERFACE "mmc"
>> -#define FAT_ENV_FILE "uboot.env"
>> -#define FAT_ENV_DEVICE_AND_PART "0"
>> -#define CONFIG_ENV_SIZE 0x4000
>> -#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 at91-sama5d3_xplained.dtb; " \
>> - "fatload mmc 0:1 0x22000000 zImage; " \
>> - "bootz 0x22000000 - 0x21000000"
>> +/* override the bootcmd, bootargs and other configuration for sd/mmc env */
>> #else
>> #define CONFIG_ENV_IS_NOWHERE
>> #endif
>> diff --git a/include/configs/sama5d3xek.h b/include/configs/sama5d3xek.h
>> index 344ae9c..71441a4 100644
>> --- a/include/configs/sama5d3xek.h
>> +++ b/include/configs/sama5d3xek.h
>> @@ -176,15 +176,7 @@
>> "nand read 0x22000000 0x200000 0x600000;" \
>> "bootm 0x22000000 - 0x21000000"
>> #elif CONFIG_SYS_USE_MMC
>> -/* bootstrap + u-boot + env in sd card */
>> -#define CONFIG_ENV_IS_IN_FAT
>> -#define FAT_ENV_INTERFACE "mmc"
>> -#define FAT_ENV_FILE "uboot.env"
>> -#define FAT_ENV_DEVICE_AND_PART "0"
>> -#define CONFIG_ENV_SIZE 0x4000
>> -#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 ${ek_name}.dtb; " \
>> - "fatload mmc 0:1 0x22000000 zImage; " \
>> - "bootm 0x22000000 - 0x21000000"
>> +/* override the bootcmd, bootargs and other configuration for sd/mmc env */
>> #else
>> #define CONFIG_ENV_IS_NOWHERE
>> #endif
>> diff --git a/include/configs/sama5d4_xplained.h b/include/configs/sama5d4_xplained.h
>> index 5fb621e..a7d9e78 100644
>> --- a/include/configs/sama5d4_xplained.h
>> +++ b/include/configs/sama5d4_xplained.h
>> @@ -13,6 +13,8 @@
>> /* No NOR flash, this definition should put before common header */
>> #define CONFIG_SYS_NO_FLASH
>>
>> +#define KERNEL_DTB_FILE_NAME "at91-sama5d4_xplained.dtb"
> This is also "at91-" + $CONFIG_SYS_BOARD + ".dtb"
>
>> +
>> #include "at91-sama5_common.h"
>>
>> /* serial console */
>> @@ -139,25 +141,9 @@
>> "nand read 0x22000000 0x200000 0x600000;" \
>> "bootz 0x22000000 - 0x21000000"
>> #elif CONFIG_SYS_USE_MMC
>> -/* bootstrap + u-boot + env in sd card */
>> -#define CONFIG_ENV_IS_IN_FAT
>> -#define CONFIG_FAT_WRITE
>> -#define FAT_ENV_INTERFACE "mmc"
>> -/*
>> - * We don't specify the part number, if device 0 has partition table, it means
>> - * the first partition; it no partition table, then take whole device as a
>> - * FAT file system.
>> - */
>> -#define FAT_ENV_DEVICE_AND_PART "0"
>> -#define FAT_ENV_FILE "uboot.env"
>> -#define CONFIG_ENV_SIZE 0x4000
>> -#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 at91-sama5d4_xplained.dtb; " \
>> - "fatload mmc 0:1 0x22000000 zImage; " \
>> - "bootz 0x22000000 - 0x21000000"
>> +/* override the bootcmd, bootargs and other configuration for sd/mmc env */
>> #endif
>>
>> -
>> -
>> /* SPL */
>> #define CONFIG_SPL_FRAMEWORK
>> #define CONFIG_SPL_TEXT_BASE 0x200000
>> diff --git a/include/configs/sama5d4ek.h b/include/configs/sama5d4ek.h
>> index 546d7a3..8ecb6d3 100644
>> --- a/include/configs/sama5d4ek.h
>> +++ b/include/configs/sama5d4ek.h
>> @@ -13,6 +13,8 @@
>> /* No NOR flash, this definition should put before common header */
>> #define CONFIG_SYS_NO_FLASH
>>
>> +#define KERNEL_DTB_FILE_NAME "sama5d4ek.dtb"
> Damn ... this lacks the presiding 'at91-'
>
> So a solution could be to rename some board's with presiding 'at91-' and
> just use the $board_name everywhere. Some board's may adopt the
> $board_name at runtime.
> What do you think about?
I think use $board_name is a good idea. We can use $board_name to
combine the dtb name.
And also we can use the CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to override
the $board_name if $board_name is not what we need exactly.
I will re-spin the v2 version patches soon. Thanks for the review.
Best Regards,
Josh Wu
>
> Andreas
>
>> +
>> #include "at91-sama5_common.h"
>>
>> /* serial console */
>> @@ -137,21 +139,7 @@
>> "nand read 0x22000000 0x200000 0x600000;" \
>> "bootz 0x22000000 - 0x21000000"
>> #elif CONFIG_SYS_USE_MMC
>> -/* bootstrap + u-boot + env in sd card */
>> -#define CONFIG_ENV_IS_IN_FAT
>> -#define CONFIG_FAT_WRITE
>> -#define FAT_ENV_INTERFACE "mmc"
>> -/*
>> - * We don't specify the part number, if device 0 has partition table, it means
>> - * the first partition; it no partition table, then take whole device as a
>> - * FAT file system.
>> - */
>> -#define FAT_ENV_DEVICE_AND_PART "0"
>> -#define FAT_ENV_FILE "uboot.env"
>> -#define CONFIG_ENV_SIZE 0x4000
>> -#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 sama5d4ek.dtb; " \
>> - "fatload mmc 0:1 0x22000000 zImage; " \
>> - "bootz 0x22000000 - 0x21000000"
>> +/* override the bootcmd, bootargs and other configuration for sd/mmc env */
>> #endif
>>
>> /* SPL */
>>
More information about the U-Boot
mailing list