[U-Boot] [PATCH V2 3/3] imx: mx6ul_14x14_evk add ENET support
Stefano Babic
sbabic at denx.de
Mon Aug 24 09:31:32 CEST 2015
Hi Peng,
On 24/08/2015 02:07, Peng Fan wrote:
> Hi Stefano,
>
> On Sun, Aug 23, 2015 at 05:45:45PM +0200, Stefano Babic wrote:
>> On 12/08/2015 10:34, Peng Fan wrote:
>>> Wrong patch version. Please ignore.
>>>
>>
>> It is, discarded.
>
> Can you please pick this one instead?
> http://lists.denx.de/pipermail/u-boot/2015-August/223124.html
> This one is the correct patch version.
> I can not find this patch in patchwork.
>
Right - I was not able to find it, too. I found only the one to be
discarded.
I applied the correct one, it is already on the server.
Regards,
Stefano Babic
> Regards,
> Peng.
>
>>
>> Best regards,
>> Stefano Babic
>>
>>> Sorry.
>>> Peng.
>>>
>>> On Wed, Aug 12, 2015 at 05:40:47PM +0800, Peng Fan wrote:
>>>> Add enet support for mx6ul_14x14_evk board:
>>>> 1. add pinmux settings
>>>> 2. implement board_eth_init
>>>> 3. implement board_phy_config
>>>>
>>>> Signed-off-by: Peng Fan <Peng.Fan at freescale.com>
>>>> Cc: Stefano Babic <sbabic at denx.de>
>>>> Cc: Fabio Estevam <fabio.estevam at freescale.com>
>>>> ---
>>>>
>>>> Changes v2:
>>>> Addressed Fabio's comments, using "fec_id == 0", but not "0 == fec_id".
>>>>
>>>> board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c | 116 ++++++++++++++++++++++
>>>> configs/mx6ul_14x14_evk_defconfig | 3 +
>>>> include/configs/mx6ul_14x14_evk.h | 21 ++++
>>>> 3 files changed, 140 insertions(+)
>>>>
>>>> diff --git a/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c b/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
>>>> index 8f712cb..af07487 100644
>>>> --- a/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
>>>> +++ b/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
>>>> @@ -19,8 +19,10 @@
>>>> #include <common.h>
>>>> #include <fsl_esdhc.h>
>>>> #include <i2c.h>
>>>> +#include <miiphy.h>
>>>> #include <linux/sizes.h>
>>>> #include <mmc.h>
>>>> +#include <netdev.h>
>>>> #include <usb.h>
>>>> #include <usb/ehci-fsl.h>
>>>>
>>>> @@ -43,6 +45,18 @@ DECLARE_GLOBAL_DATA_PTR;
>>>> PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
>>>> PAD_CTL_ODE)
>>>>
>>>> +#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
>>>> + PAD_CTL_SPEED_HIGH | \
>>>> + PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST)
>>>> +
>>>> +#define MDIO_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
>>>> + PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST | PAD_CTL_ODE)
>>>> +
>>>> +#define ENET_CLK_PAD_CTRL (PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
>>>> +
>>>> +#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
>>>> + PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST)
>>>> +
>>>> #define IOX_SDI IMX_GPIO_NR(5, 10)
>>>> #define IOX_STCP IMX_GPIO_NR(5, 7)
>>>> #define IOX_SHCP IMX_GPIO_NR(5, 11)
>>>> @@ -457,6 +471,104 @@ int board_ehci_hcd_init(int port)
>>>> }
>>>> #endif
>>>>
>>>> +#ifdef CONFIG_FEC_MXC
>>>> +/*
>>>> + * pin conflicts for fec1 and fec2, GPIO1_IO06 and GPIO1_IO07 can only
>>>> + * be used for ENET1 or ENET2, cannot be used for both.
>>>> + */
>>>> +static iomux_v3_cfg_t const fec1_pads[] = {
>>>> + MX6_PAD_GPIO1_IO06__ENET1_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
>>>> + MX6_PAD_GPIO1_IO07__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>>> + MX6_PAD_ENET1_TX_DATA0__ENET1_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>>> + MX6_PAD_ENET1_TX_DATA1__ENET1_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>>> + MX6_PAD_ENET1_TX_EN__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>>> + MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
>>>> + MX6_PAD_ENET1_RX_DATA0__ENET1_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>>> + MX6_PAD_ENET1_RX_DATA1__ENET1_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>>> + MX6_PAD_ENET1_RX_ER__ENET1_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>>> + MX6_PAD_ENET1_RX_EN__ENET1_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>>> +};
>>>> +
>>>> +static iomux_v3_cfg_t const fec2_pads[] = {
>>>> + MX6_PAD_GPIO1_IO06__ENET2_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
>>>> + MX6_PAD_GPIO1_IO07__ENET2_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>>> +
>>>> + MX6_PAD_ENET2_TX_DATA0__ENET2_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>>> + MX6_PAD_ENET2_TX_DATA1__ENET2_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>>> + MX6_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
>>>> + MX6_PAD_ENET2_TX_EN__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>>> +
>>>> + MX6_PAD_ENET2_RX_DATA0__ENET2_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>>> + MX6_PAD_ENET2_RX_DATA1__ENET2_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>>> + MX6_PAD_ENET2_RX_EN__ENET2_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>>> + MX6_PAD_ENET2_RX_ER__ENET2_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>>> +};
>>>> +
>>>> +static void setup_iomux_fec(int fec_id)
>>>> +{
>>>> + if (fec_id == 0)
>>>> + imx_iomux_v3_setup_multiple_pads(fec1_pads,
>>>> + ARRAY_SIZE(fec1_pads));
>>>> + else
>>>> + imx_iomux_v3_setup_multiple_pads(fec2_pads,
>>>> + ARRAY_SIZE(fec2_pads));
>>>> +}
>>>> +
>>>> +int board_eth_init(bd_t *bis)
>>>> +{
>>>> + int ret;
>>>> +
>>>> + setup_iomux_fec(CONFIG_FEC_ENET_DEV);
>>>> +
>>>> + ret = fecmxc_initialize_multi(bis, CONFIG_FEC_ENET_DEV,
>>>> + CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
>>>> + if (ret)
>>>> + printf("FEC%d MXC: %s:failed\n", CONFIG_FEC_ENET_DEV, __func__);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int setup_fec(int fec_id)
>>>> +{
>>>> + struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
>>>> + int ret;
>>>> +
>>>> + if (fec_id == 0) {
>>>> + /*
>>>> + * Use 50M anatop loopback REF_CLK1 for ENET1,
>>>> + * clear gpr1[13], set gpr1[17].
>>>> + */
>>>> + clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
>>>> + IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
>>>> + } else {
>>>> + /*
>>>> + * Use 50M anatop loopback REF_CLK2 for ENET2,
>>>> + * clear gpr1[14], set gpr1[18].
>>>> + */
>>>> + clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK,
>>>> + IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
>>>> + }
>>>> +
>>>> + ret = enable_fec_anatop_clock(fec_id, ENET_50MHZ);
>>>> + if (ret)
>>>> + return ret;
>>>> +
>>>> + enable_enet_clk(1);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +int board_phy_config(struct phy_device *phydev)
>>>> +{
>>>> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
>>>> +
>>>> + if (phydev->drv->config)
>>>> + phydev->drv->config(phydev);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +#endif
>>>> +
>>>> int board_early_init_f(void)
>>>> {
>>>> setup_iomux_uart();
>>>> @@ -477,6 +589,10 @@ int board_init(void)
>>>> setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
>>>> #endif
>>>>
>>>> +#ifdef CONFIG_FEC_MXC
>>>> + setup_fec(CONFIG_FEC_ENET_DEV);
>>>> +#endif
>>>> +
>>>> #ifdef CONFIG_USB_EHCI_MX6
>>>> setup_usb();
>>>> #endif
>>>> diff --git a/configs/mx6ul_14x14_evk_defconfig b/configs/mx6ul_14x14_evk_defconfig
>>>> index b6eefaf..85952e4 100644
>>>> --- a/configs/mx6ul_14x14_evk_defconfig
>>>> +++ b/configs/mx6ul_14x14_evk_defconfig
>>>> @@ -2,3 +2,6 @@ CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,MX6UL"
>>>> CONFIG_ARM=y
>>>> CONFIG_TARGET_MX6UL_14X14_EVK=y
>>>> CONFIG_SPL=y
>>>> +CONFIG_CMD_NET=y
>>>> +CONFIG_CMD_PING=y
>>>> +CONFIG_CMD_DHCP=y
>>>> diff --git a/include/configs/mx6ul_14x14_evk.h b/include/configs/mx6ul_14x14_evk.h
>>>> index 757aa6a..f643e4d 100644
>>>> --- a/include/configs/mx6ul_14x14_evk.h
>>>> +++ b/include/configs/mx6ul_14x14_evk.h
>>>> @@ -221,6 +221,27 @@
>>>> #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
>>>> #endif
>>>>
>>>> +#ifdef CONFIG_CMD_NET
>>>> +#define CONFIG_FEC_MXC
>>>> +#define CONFIG_MII
>>>> +#define CONFIG_FEC_ENET_DEV 1
>>>> +
>>>> +#if (CONFIG_FEC_ENET_DEV == 0)
>>>> +#define IMX_FEC_BASE ENET_BASE_ADDR
>>>> +#define CONFIG_FEC_MXC_PHYADDR 0x2
>>>> +#define CONFIG_FEC_XCV_TYPE RMII
>>>> +#elif (CONFIG_FEC_ENET_DEV == 1)
>>>> +#define IMX_FEC_BASE ENET2_BASE_ADDR
>>>> +#define CONFIG_FEC_MXC_PHYADDR 0x1
>>>> +#define CONFIG_FEC_XCV_TYPE RMII
>>>> +#endif
>>>> +#define CONFIG_ETHPRIME "FEC"
>>>> +
>>>> +#define CONFIG_PHYLIB
>>>> +#define CONFIG_PHY_MICREL
>>>> +#define CONFIG_FEC_DMA_MINALIGN 64
>>>> +#endif
>>>> +
>>>> #define CONFIG_IMX6_THERMAL
>>>>
>>>> #endif
>>>> --
>>>> 1.8.4
>>>>
>>>>
>>>
>>
>>
>> --
>> =====================================================================
>> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
>> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
>> Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
>> =====================================================================
>
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
More information about the U-Boot
mailing list