[U-Boot] [PATCH] thermal: imx_thermal: rework driver to be reused
Stefano Babic
sbabic at denx.de
Tue Aug 25 19:22:44 CEST 2015
Hi Adrian,
On 25/08/2015 18:07, Adrian Alonso wrote:
> - Rework imx_thermal driver to be used across i.MX
> processor that support thermal sensors
ok
> - Make read_cpu_temperature SoC dependent
Agree on that, but why moving into the soc / cpu file ?
We have a driver for a specific hardware. The driver supports more as
one SOC. it is a common case. We have already such a cases, and the
driver must have code for both of them.
Take as example the SPI driver (on u-boot or Linux). It supports
multiple i.MXes without demanding code outside of the driver itself.
Aomething like:
read_cpu_temperature_mx6(....)
{
}
read_cpu_temperature_mx7(....)
{
}
int read_cpu_temperature(struct udevice *dev)
{
<check cpu type, call right function>
}
I think moving "read_cpu_temperature" is wrong because everybody expects
that all stuff related to the thermal is in the corresponding driver,
that is imx-thermal.
>
> Signed-off-by: Adrian Alonso <aalonso at freescale.com>
> Signed-off-by: Peng Fan <Peng.Fan at freescale.com>
> ---
> arch/arm/cpu/armv7/mx6/soc.c | 86 +++++++++++++++++++++++-
> arch/arm/imx-common/cpu.c | 13 ++--
> arch/arm/include/asm/arch-mx6/sys_proto.h | 2 +
> drivers/thermal/Makefile | 2 +-
> drivers/thermal/imx_thermal.c | 106 ------------------------------
> include/configs/cgtqmx6eval.h | 4 +-
> include/configs/embestmx6boards.h | 2 +-
> include/configs/gw_ventana.h | 2 +-
> include/configs/mx6cuboxi.h | 2 +-
> include/configs/mx6sabre_common.h | 2 +-
> include/configs/mx6slevk.h | 2 +-
> include/configs/mx6sxsabresd.h | 2 +-
> include/configs/mx6ul_14x14_evk.h | 2 +-
> include/configs/tbs2910.h | 2 +-
> include/imx_thermal.h | 26 ++++++++
> 15 files changed, 130 insertions(+), 125 deletions(-)
>
> diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c
> index 8ad8da8..68f4507 100644
> --- a/arch/arm/cpu/armv7/mx6/soc.c
> +++ b/arch/arm/cpu/armv7/mx6/soc.c
> @@ -22,6 +22,7 @@
> #include <asm/arch/mxc_hdmi.h>
> #include <asm/arch/crm_regs.h>
> #include <dm.h>
> +#include <div64.h>
> #include <imx_thermal.h>
>
> enum ldo_reg {
> @@ -38,7 +39,7 @@ struct scu_regs {
> u32 fpga_rev;
> };
>
> -#if defined(CONFIG_IMX6_THERMAL)
> +#if defined(CONFIG_IMX_THERMAL)
> static const struct imx_thermal_plat imx6_thermal_plat = {
> .regs = (void *)ANATOP_BASE_ADDR,
> .fuse_bank = 1,
> @@ -171,6 +172,89 @@ u32 get_cpu_temp_grade(int *minc, int *maxc)
> return val;
> }
>
> +int read_cpu_temperature(struct udevice *dev)
> +{
> + int temperature;
> + unsigned int reg, n_meas;
> + const struct imx_thermal_plat *pdata = dev_get_platdata(dev);
> + struct anatop_regs *anatop = (struct anatop_regs *)pdata->regs;
> + struct thermal_data *priv = dev_get_priv(dev);
> + u32 fuse = priv->fuse;
> + int t1, n1;
> + u32 c1, c2;
> + u64 temp64;
> +
> + /*
> + * Sensor data layout:
> + * [31:20] - sensor value @ 25C
> + * We use universal formula now and only need sensor value @ 25C
> + * slope = 0.4297157 - (0.0015976 * 25C fuse)
> + */
> + n1 = fuse >> 20;
> + t1 = 25; /* t1 always 25C */
> +
> + /*
> + * Derived from linear interpolation:
> + * slope = 0.4297157 - (0.0015976 * 25C fuse)
> + * slope = (FACTOR2 - FACTOR1 * n1) / FACTOR0
> + * (Nmeas - n1) / (Tmeas - t1) = slope
> + * We want to reduce this down to the minimum computation necessary
> + * for each temperature read. Also, we want Tmeas in millicelsius
> + * and we don't want to lose precision from integer division. So...
> + * Tmeas = (Nmeas - n1) / slope + t1
> + * milli_Tmeas = 1000 * (Nmeas - n1) / slope + 1000 * t1
> + * milli_Tmeas = -1000 * (n1 - Nmeas) / slope + 1000 * t1
> + * Let constant c1 = (-1000 / slope)
> + * milli_Tmeas = (n1 - Nmeas) * c1 + 1000 * t1
> + * Let constant c2 = n1 *c1 + 1000 * t1
> + * milli_Tmeas = c2 - Nmeas * c1
> + */
> + temp64 = FACTOR0;
> + temp64 *= 1000;
> + do_div(temp64, FACTOR1 * n1 - FACTOR2);
> + c1 = temp64;
> + c2 = n1 * c1 + 1000 * t1;
> +
> + /*
> + * now we only use single measure, every time we read
> + * the temperature, we will power on/down anadig thermal
> + * module
> + */
> + writel(TEMPSENSE0_POWER_DOWN, &anatop->tempsense0_clr);
> + writel(MISC0_REFTOP_SELBIASOFF, &anatop->ana_misc0_set);
> +
> + /* setup measure freq */
> + reg = readl(&anatop->tempsense1);
> + reg &= ~TEMPSENSE1_MEASURE_FREQ;
> + reg |= MEASURE_FREQ;
> + writel(reg, &anatop->tempsense1);
> +
> + /* start the measurement process */
> + writel(TEMPSENSE0_MEASURE_TEMP, &anatop->tempsense0_clr);
> + writel(TEMPSENSE0_FINISHED, &anatop->tempsense0_clr);
> + writel(TEMPSENSE0_MEASURE_TEMP, &anatop->tempsense0_set);
> +
> + /* make sure that the latest temp is valid */
> + while ((readl(&anatop->tempsense0) &
> + TEMPSENSE0_FINISHED) == 0)
> + udelay(10000);
> +
> + /* read temperature count */
> + reg = readl(&anatop->tempsense0);
> + n_meas = (reg & TEMPSENSE0_TEMP_CNT_MASK)
> + >> TEMPSENSE0_TEMP_CNT_SHIFT;
> + writel(TEMPSENSE0_FINISHED, &anatop->tempsense0_clr);
> +
> + /* milli_Tmeas = c2 - Nmeas * c1 */
> + temperature = (long)(c2 - n_meas * c1)/1000;
> +
> + /* power down anatop thermal sensor */
> + writel(TEMPSENSE0_POWER_DOWN, &anatop->tempsense0_set);
> + writel(MISC0_REFTOP_SELBIASOFF, &anatop->ana_misc0_clr);
> +
> + return temperature;
> +}
> +
> #ifdef CONFIG_REVISION_TAG
> u32 __weak get_board_rev(void)
> {
> diff --git a/arch/arm/imx-common/cpu.c b/arch/arm/imx-common/cpu.c
> index e27546c..a5efbd5 100644
> --- a/arch/arm/imx-common/cpu.c
> +++ b/arch/arm/imx-common/cpu.c
> @@ -154,14 +154,13 @@ int print_cpuinfo(void)
> u32 cpurev;
> __maybe_unused u32 max_freq;
>
> -#if defined(CONFIG_MX6) && defined(CONFIG_IMX6_THERMAL)
> - struct udevice *thermal_dev;
> - int cpu_tmp, minc, maxc, ret;
> -#endif
> -
> cpurev = get_cpu_rev();
>
> -#if defined(CONFIG_MX6)
> +#if defined(CONFIG_IMX_THERMAL)
> + struct udevice *thermal_dev;
> + int cpu_tmp, ret;
> + int minc, maxc;
> +
> printf("CPU: Freescale i.MX%s rev%d.%d",
> get_imx_type((cpurev & 0xFF000) >> 12),
> (cpurev & 0x000F0) >> 4,
> @@ -181,7 +180,7 @@ int print_cpuinfo(void)
> mxc_get_clock(MXC_ARM_CLK) / 1000000);
> #endif
>
> -#if defined(CONFIG_MX6) && defined(CONFIG_IMX6_THERMAL)
> +#if defined(CONFIG_IMX_THERMAL)
> puts("CPU: ");
> switch (get_cpu_temp_grade(&minc, &maxc)) {
> case TEMP_AUTOMOTIVE:
> diff --git a/arch/arm/include/asm/arch-mx6/sys_proto.h b/arch/arm/include/asm/arch-mx6/sys_proto.h
> index eee8ca8..c4e6ddc 100644
> --- a/arch/arm/include/asm/arch-mx6/sys_proto.h
> +++ b/arch/arm/include/asm/arch-mx6/sys_proto.h
> @@ -8,6 +8,7 @@
> #ifndef _SYS_PROTO_H_
> #define _SYS_PROTO_H_
>
> +#include <dm.h>
> #include <asm/imx-common/regs-common.h>
> #include "../arch-imx/cpu.h"
>
> @@ -18,6 +19,7 @@ u32 get_nr_cpus(void);
> u32 get_cpu_rev(void);
> u32 get_cpu_speed_grade_hz(void);
> u32 get_cpu_temp_grade(int *minc, int *maxc);
> +int read_cpu_temperature(struct udevice *dev);
>
> /* returns MXC_CPU_ value */
> #define cpu_type(rev) (((rev) >> 12) & 0xff)
> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> index 6d4cacd..d768f5e 100644
> --- a/drivers/thermal/Makefile
> +++ b/drivers/thermal/Makefile
> @@ -6,4 +6,4 @@
> #
>
> obj-$(CONFIG_DM_THERMAL) += thermal-uclass.o
> -obj-$(CONFIG_IMX6_THERMAL) += imx_thermal.o
> +obj-$(CONFIG_IMX_THERMAL) += imx_thermal.o
> diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c
> index 3c6c967..f037f81 100644
> --- a/drivers/thermal/imx_thermal.c
> +++ b/drivers/thermal/imx_thermal.c
> @@ -8,7 +8,6 @@
>
> #include <config.h>
> #include <common.h>
> -#include <div64.h>
> #include <fuse.h>
> #include <asm/io.h>
> #include <asm/arch/clock.h>
> @@ -19,111 +18,6 @@
> #include <thermal.h>
> #include <imx_thermal.h>
>
> -/* board will busyloop until this many degrees C below CPU max temperature */
> -#define TEMPERATURE_HOT_DELTA 5 /* CPU maxT - 5C */
> -#define FACTOR0 10000000
> -#define FACTOR1 15976
> -#define FACTOR2 4297157
> -#define MEASURE_FREQ 327
> -
> -#define TEMPSENSE0_TEMP_CNT_SHIFT 8
> -#define TEMPSENSE0_TEMP_CNT_MASK (0xfff << TEMPSENSE0_TEMP_CNT_SHIFT)
> -#define TEMPSENSE0_FINISHED (1 << 2)
> -#define TEMPSENSE0_MEASURE_TEMP (1 << 1)
> -#define TEMPSENSE0_POWER_DOWN (1 << 0)
> -#define MISC0_REFTOP_SELBIASOFF (1 << 3)
> -#define TEMPSENSE1_MEASURE_FREQ 0xffff
> -
> -struct thermal_data {
> - unsigned int fuse;
> - int critical;
> - int minc;
> - int maxc;
> -};
> -
> -static int read_cpu_temperature(struct udevice *dev)
> -{
> - int temperature;
> - unsigned int reg, n_meas;
> - const struct imx_thermal_plat *pdata = dev_get_platdata(dev);
> - struct anatop_regs *anatop = (struct anatop_regs *)pdata->regs;
> - struct thermal_data *priv = dev_get_priv(dev);
> - u32 fuse = priv->fuse;
> - int t1, n1;
> - u32 c1, c2;
> - u64 temp64;
> -
> - /*
> - * Sensor data layout:
> - * [31:20] - sensor value @ 25C
> - * We use universal formula now and only need sensor value @ 25C
> - * slope = 0.4297157 - (0.0015976 * 25C fuse)
> - */
> - n1 = fuse >> 20;
> - t1 = 25; /* t1 always 25C */
> -
> - /*
> - * Derived from linear interpolation:
> - * slope = 0.4297157 - (0.0015976 * 25C fuse)
> - * slope = (FACTOR2 - FACTOR1 * n1) / FACTOR0
> - * (Nmeas - n1) / (Tmeas - t1) = slope
> - * We want to reduce this down to the minimum computation necessary
> - * for each temperature read. Also, we want Tmeas in millicelsius
> - * and we don't want to lose precision from integer division. So...
> - * Tmeas = (Nmeas - n1) / slope + t1
> - * milli_Tmeas = 1000 * (Nmeas - n1) / slope + 1000 * t1
> - * milli_Tmeas = -1000 * (n1 - Nmeas) / slope + 1000 * t1
> - * Let constant c1 = (-1000 / slope)
> - * milli_Tmeas = (n1 - Nmeas) * c1 + 1000 * t1
> - * Let constant c2 = n1 *c1 + 1000 * t1
> - * milli_Tmeas = c2 - Nmeas * c1
> - */
> - temp64 = FACTOR0;
> - temp64 *= 1000;
> - do_div(temp64, FACTOR1 * n1 - FACTOR2);
> - c1 = temp64;
> - c2 = n1 * c1 + 1000 * t1;
> -
> - /*
> - * now we only use single measure, every time we read
> - * the temperature, we will power on/down anadig thermal
> - * module
> - */
> - writel(TEMPSENSE0_POWER_DOWN, &anatop->tempsense0_clr);
> - writel(MISC0_REFTOP_SELBIASOFF, &anatop->ana_misc0_set);
> -
> - /* setup measure freq */
> - reg = readl(&anatop->tempsense1);
> - reg &= ~TEMPSENSE1_MEASURE_FREQ;
> - reg |= MEASURE_FREQ;
> - writel(reg, &anatop->tempsense1);
> -
> - /* start the measurement process */
> - writel(TEMPSENSE0_MEASURE_TEMP, &anatop->tempsense0_clr);
> - writel(TEMPSENSE0_FINISHED, &anatop->tempsense0_clr);
> - writel(TEMPSENSE0_MEASURE_TEMP, &anatop->tempsense0_set);
> -
> - /* make sure that the latest temp is valid */
> - while ((readl(&anatop->tempsense0) &
> - TEMPSENSE0_FINISHED) == 0)
> - udelay(10000);
> -
> - /* read temperature count */
> - reg = readl(&anatop->tempsense0);
> - n_meas = (reg & TEMPSENSE0_TEMP_CNT_MASK)
> - >> TEMPSENSE0_TEMP_CNT_SHIFT;
> - writel(TEMPSENSE0_FINISHED, &anatop->tempsense0_clr);
> -
> - /* milli_Tmeas = c2 - Nmeas * c1 */
> - temperature = (long)(c2 - n_meas * c1)/1000;
> -
> - /* power down anatop thermal sensor */
> - writel(TEMPSENSE0_POWER_DOWN, &anatop->tempsense0_set);
> - writel(MISC0_REFTOP_SELBIASOFF, &anatop->ana_misc0_clr);
> -
> - return temperature;
> -}
> -
> int imx_thermal_get_temp(struct udevice *dev, int *temp)
> {
> struct thermal_data *priv = dev_get_priv(dev);
> diff --git a/include/configs/cgtqmx6eval.h b/include/configs/cgtqmx6eval.h
> index fb5b82e..c21f178 100644
> --- a/include/configs/cgtqmx6eval.h
> +++ b/include/configs/cgtqmx6eval.h
> @@ -33,10 +33,10 @@
> #define CONFIG_CMD_BMODE
>
> /* Thermal support */
> -#define CONFIG_IMX6_THERMAL
> +#define CONFIG_IMX_THERMAL
>
> #define CONFIG_CMD_FUSE
> -#if defined(CONFIG_CMD_FUSE) || defined(CONFIG_IMX6_THERMAL)
> +#if defined(CONFIG_CMD_FUSE) || defined(CONFIG_IMX_THERMAL)
> #define CONFIG_MXC_OCOTP
> #endif
>
> diff --git a/include/configs/embestmx6boards.h b/include/configs/embestmx6boards.h
> index 12744a6..58cee96 100644
> --- a/include/configs/embestmx6boards.h
> +++ b/include/configs/embestmx6boards.h
> @@ -19,7 +19,7 @@
>
> #define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
>
> -#define CONFIG_IMX6_THERMAL
> +#define CONFIG_IMX_THERMAL
>
> /* Size of malloc() pool */
> #define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
> diff --git a/include/configs/gw_ventana.h b/include/configs/gw_ventana.h
> index 8b9d922..231bea7 100644
> --- a/include/configs/gw_ventana.h
> +++ b/include/configs/gw_ventana.h
> @@ -57,7 +57,7 @@
> #define CONFIG_CMD_GPIO
>
> /* Thermal */
> -#define CONFIG_IMX6_THERMAL
> +#define CONFIG_IMX_THERMAL
>
> /* Serial */
> #define CONFIG_MXC_UART
> diff --git a/include/configs/mx6cuboxi.h b/include/configs/mx6cuboxi.h
> index 634a09f..6e89dd1 100644
> --- a/include/configs/mx6cuboxi.h
> +++ b/include/configs/mx6cuboxi.h
> @@ -14,7 +14,7 @@
> #define CONFIG_SPL_MMC_SUPPORT
> #include "imx6_spl.h"
>
> -#define CONFIG_IMX6_THERMAL
> +#define CONFIG_IMX_THERMAL
>
> #define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
> #define CONFIG_BOARD_EARLY_INIT_F
> diff --git a/include/configs/mx6sabre_common.h b/include/configs/mx6sabre_common.h
> index 6a57841..98eb042 100644
> --- a/include/configs/mx6sabre_common.h
> +++ b/include/configs/mx6sabre_common.h
> @@ -11,7 +11,7 @@
>
> #include "mx6_common.h"
>
> -#define CONFIG_IMX6_THERMAL
> +#define CONFIG_IMX_THERMAL
>
> /* Size of malloc() pool */
> #define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
> diff --git a/include/configs/mx6slevk.h b/include/configs/mx6slevk.h
> index 3cecd94..58e59d8 100644
> --- a/include/configs/mx6slevk.h
> +++ b/include/configs/mx6slevk.h
> @@ -190,6 +190,6 @@
> #define CONFIG_SYS_MMC_ENV_DEV 1 /* SDHC2*/
> #endif
>
> -#define CONFIG_IMX6_THERMAL
> +#define CONFIG_IMX_THERMAL
>
> #endif /* __CONFIG_H */
> diff --git a/include/configs/mx6sxsabresd.h b/include/configs/mx6sxsabresd.h
> index 848bdcd..381eaa2 100644
> --- a/include/configs/mx6sxsabresd.h
> +++ b/include/configs/mx6sxsabresd.h
> @@ -176,7 +176,7 @@
> #define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(2, 1)
> #endif
>
> -#define CONFIG_IMX6_THERMAL
> +#define CONFIG_IMX_THERMAL
>
> #define CONFIG_CMD_TIME
>
> diff --git a/include/configs/mx6ul_14x14_evk.h b/include/configs/mx6ul_14x14_evk.h
> index 6ae736f..7c48313 100644
> --- a/include/configs/mx6ul_14x14_evk.h
> +++ b/include/configs/mx6ul_14x14_evk.h
> @@ -221,6 +221,6 @@
> #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
> #endif
>
> -#define CONFIG_IMX6_THERMAL
> +#define CONFIG_IMX_THERMAL
>
> #endif
> diff --git a/include/configs/tbs2910.h b/include/configs/tbs2910.h
> index 66cb274..70b4403 100644
> --- a/include/configs/tbs2910.h
> +++ b/include/configs/tbs2910.h
> @@ -20,7 +20,7 @@
>
> #define CONFIG_SYS_HZ 1000
>
> -#define CONFIG_IMX6_THERMAL
> +#define CONFIG_IMX_THERMAL
>
> /* Physical Memory Map */
> #define CONFIG_NR_DRAM_BANKS 1
> diff --git a/include/imx_thermal.h b/include/imx_thermal.h
> index 8ce333c..62fed3b 100644
> --- a/include/imx_thermal.h
> +++ b/include/imx_thermal.h
> @@ -20,4 +20,30 @@ struct imx_thermal_plat {
> int fuse_word;
> };
>
> +struct thermal_data {
> + unsigned int fuse;
> + int critical;
> + int minc;
> + int maxc;
> +};
> +
> +/* board will busyloop until this many degrees C below CPU max temperature */
> +#define TEMPERATURE_HOT_DELTA 5 /* CPU maxT - 5C */
> +#define FACTOR0 10000000
> +#define FACTOR1 15976
> +#define FACTOR2 4297157
> +#define MEASURE_FREQ 327
> +
> +#define TEMPERATURE_MIN -40
> +#define TEMPERATURE_HOT 85
> +#define TEMPERATURE_MAX 125
> +
> +#define TEMPSENSE0_TEMP_CNT_SHIFT 8
> +#define TEMPSENSE0_TEMP_CNT_MASK (0xfff << TEMPSENSE0_TEMP_CNT_SHIFT)
> +#define TEMPSENSE0_FINISHED (1 << 2)
> +#define TEMPSENSE0_MEASURE_TEMP (1 << 1)
> +#define TEMPSENSE0_POWER_DOWN (1 << 0)
> +#define MISC0_REFTOP_SELBIASOFF (1 << 3)
> +#define TEMPSENSE1_MEASURE_FREQ 0xffff
> +
> #endif /* _IMX_THERMAL_H_ */
>
Regards,
Stefano
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
More information about the U-Boot
mailing list