[U-Boot] [PATCH 34/45] arm: Remove tk71 board
Simon Glass
sjg at chromium.org
Mon Aug 31 03:19:28 CEST 2015
This board has not been converted to generic board by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg at chromium.org>
---
arch/arm/mach-kirkwood/Kconfig | 4 --
board/karo/tk71/Kconfig | 12 ----
board/karo/tk71/MAINTAINERS | 6 --
board/karo/tk71/Makefile | 9 ---
board/karo/tk71/kwbimage.cfg | 158 -----------------------------------------
board/karo/tk71/tk71.c | 150 --------------------------------------
configs/tk71_defconfig | 6 --
include/configs/tk71.h | 112 -----------------------------
8 files changed, 457 deletions(-)
delete mode 100644 board/karo/tk71/Kconfig
delete mode 100644 board/karo/tk71/MAINTAINERS
delete mode 100644 board/karo/tk71/Makefile
delete mode 100644 board/karo/tk71/kwbimage.cfg
delete mode 100644 board/karo/tk71/tk71.c
delete mode 100644 configs/tk71_defconfig
delete mode 100644 include/configs/tk71.h
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index 27c09a7..c5491e4 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -25,9 +25,6 @@ config TARGET_DNS325
config TARGET_ICONNECT
bool "iconnect Board"
-config TARGET_TK71
- bool "TK71 Board"
-
config TARGET_KM_KIRKWOOD
bool "KM_KIRKWOOD Board"
@@ -55,7 +52,6 @@ source "board/buffalo/lsxl/Kconfig"
source "board/cloudengines/pogo_e02/Kconfig"
source "board/d-link/dns325/Kconfig"
source "board/iomega/iconnect/Kconfig"
-source "board/karo/tk71/Kconfig"
source "board/keymile/km_arm/Kconfig"
source "board/raidsonic/ib62x0/Kconfig"
source "board/Seagate/dockstar/Kconfig"
diff --git a/board/karo/tk71/Kconfig b/board/karo/tk71/Kconfig
deleted file mode 100644
index 7b3d548..0000000
--- a/board/karo/tk71/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_TK71
-
-config SYS_BOARD
- default "tk71"
-
-config SYS_VENDOR
- default "karo"
-
-config SYS_CONFIG_NAME
- default "tk71"
-
-endif
diff --git a/board/karo/tk71/MAINTAINERS b/board/karo/tk71/MAINTAINERS
deleted file mode 100644
index ac85d6b..0000000
--- a/board/karo/tk71/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-TK71 BOARD
-#M: -
-S: Maintained
-F: board/karo/tk71/
-F: include/configs/tk71.h
-F: configs/tk71_defconfig
diff --git a/board/karo/tk71/Makefile b/board/karo/tk71/Makefile
deleted file mode 100644
index 0e0df77..0000000
--- a/board/karo/tk71/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# Copyright (C) 2012 Marek Vasut <marex at denx.de>
-# on behalf of DENX Software Engineering GmbH
-#
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := tk71.o
diff --git a/board/karo/tk71/kwbimage.cfg b/board/karo/tk71/kwbimage.cfg
deleted file mode 100644
index a32e27c..0000000
--- a/board/karo/tk71/kwbimage.cfg
+++ /dev/null
@@ -1,158 +0,0 @@
-#
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
-#
-# adopted to TK71 by
-# Nils Faerber <nils.faerber at kernelconcepts.de>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Refer doc/README.kwbimage for more details about how-to configure
-# and create kirkwood boot image
-#
-
-# Boot Media configurations
-BOOT_FROM nand
-NAND_ECC_MODE default
-NAND_PAGE_SIZE 0x0800
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1b1b1b9b
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000c30 # DDR Configuration register
-# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
-# bit23-14: zero
-# bit24: 1= enable exit self refresh mode on DDR access
-# bit25: 1 required
-# bit29-26: zero
-# bit31-30: 01
-
-DATA 0xFFD01404 0x36543000 # DDR Controller Control Low
-# bit 4: 0=addr/cmd in smame cycle
-# bit 5: 0=clk is driven during self refresh, we don't care for APX
-# bit 6: 0=use recommended falling edge of clk for addr/cmd
-# bit14: 0=input buffer always powered up
-# bit18: 1=cpu lock transaction enabled
-# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
-# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
-# bit30-28: 3 required
-# bit31: 0=no additional STARTBURST delay
-
-DATA 0xFFD01408 0x1101355b # DDR Timing (Low) (active cycles value +1)
-# bit3-0: TRAS lsbs
-# bit7-4: TRCD
-# bit11- 8: TRP
-# bit15-12: TWR
-# bit19-16: TWTR
-# bit20: TRAS msb
-# bit23-21: 0x0
-# bit27-24: TRRD
-# bit31-28: TRTP
-
-DATA 0xFFD0140C 0x00000034 # DDR Timing (High)
-# bit6-0: TRFC
-# bit8-7: TR2R
-# bit10-9: TR2W
-# bit12-11: TW2W
-# bit31-13: zero required
-
-DATA 0xFFD01410 0x00000000 # DDR Address Control
-# bit1-0: 01, Cs0width=x16
-# bit3-2: 10, Cs0size=512Mb
-# bit5-4: 01, Cs1width=x16
-# bit7-6: 10, Cs1size=512Mb
-# bit9-8: 00, Cs2width=nonexistent
-# bit11-10: 00, Cs2size =nonexistent
-# bit13-12: 00, Cs3width=nonexistent
-# bit15-14: 00, Cs3size =nonexistent
-# bit16: 0, Cs0AddrSel
-# bit17: 0, Cs1AddrSel
-# bit18: 0, Cs2AddrSel
-# bit19: 0, Cs3AddrSel
-# bit31-20: 0 required
-
-DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
-# bit0: 0, OpenPage enabled
-# bit31-1: 0 required
-
-DATA 0xFFD01418 0x00000000 # DDR Operation
-# bit3-0: 0x0, DDR cmd
-# bit31-4: 0 required
-
-DATA 0xFFD0141C 0x00000652 # DDR Mode
-# bit2-0: 2, BurstLen=2 required
-# bit3: 0, BurstType=0 required
-# bit6-4: 4, CL=5
-# bit7: 0, TestMode=0 normal
-# bit8: 0, DLL reset=0 normal
-# bit11-9: 6, auto-precharge write recovery ????????????
-# bit12: 0, PD must be zero
-# bit31-13: 0 required
-
-DATA 0xFFD01420 0x00000042 # DDR Extended Mode
-# bit0: 0, DDR DLL enabled
-# bit1: 0, DDR drive strenght normal
-# bit2: 0, DDR ODT control lsd (disabled)
-# bit5-3: 000, required
-# bit6: 1, DDR ODT control msb, (disabled)
-# bit9-7: 000, required
-# bit10: 0, differential DQS enabled
-# bit11: 0, required
-# bit12: 0, DDR output buffer enabled
-# bit31-13: 0 required
-
-DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
-# bit2-0: 111, required
-# bit3 : 1 , MBUS Burst Chop disabled
-# bit6-4: 111, required
-# bit7 : 0
-# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
-# bit9 : 0 , no half clock cycle addition to dataout
-# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
-# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
-# bit15-12: 1111 required
-# bit31-16: 0 required
-
-DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
-DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
-DATA 0xFFD01504 0x1FFFFFF1 # CS[0]n Size
-# bit0: 1, Window enabled
-# bit1: 0, Write Protect disabled
-# bit3-2: 00, CS0 hit selected
-# bit23-4: ones, required
-# bit31-24: 0x0F, Size (i.e. 256MB)
-
-DATA 0xFFD01508 0x00000000 # CS[1]n Base address to 256Mb
-DATA 0xFFD0150C 0x00000000 # CS[1]n Size 256Mb Window enabled for CS1
-
-DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
-
-DATA 0xFFD01494 0x00110000 # DDR ODT Control (Low)
-# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1
-# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0
-# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
-# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
-DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
-# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
-# bit3-2: 01, ODT1 active NEVER!
-# bit31-4: zero, required
-
-DATA 0xFFD0149C 0x0000F80F # CPU ODT Control
-# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3
-# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
-# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
-# bit14: 1, M_STARTBURST_IN ODT: Enabled
-# bit15: 1, DDR IO ODT Unit: Use ODT block
-DATA 0xFFD01480 0x00000001 # DDR Initialization Control
-#bit0=1, enable DDR init upon this register write
-
-# End of Header extension
-DATA 0x0 0x0
diff --git a/board/karo/tk71/tk71.c b/board/karo/tk71/tk71.c
deleted file mode 100644
index 35546d2..0000000
--- a/board/karo/tk71/tk71.c
+++ /dev/null
@@ -1,150 +0,0 @@
-/*
- * Copyright (C) 2012 Marek Vasut <marex at denx.de>
- * on behalf of DENX Software Engineering GmbH
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <miiphy.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-#include <asm/arch/mpp.h>
-#include <asm/io.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define TK71_OE_LOW (~0)
-#define TK71_OE_HIGH (~0)
-#define TK71_OE_VAL_LOW (0)
-#define TK71_OE_VAL_HIGH (0)
-
-int board_early_init_f(void)
-{
- /*
- * default gpio configuration
- * There are maximum 64 gpios controlled through 2 sets of registers
- * the below configuration configures mainly initial LED status
- */
- mvebu_config_gpio(TK71_OE_VAL_LOW,
- TK71_OE_VAL_HIGH,
- TK71_OE_LOW, TK71_OE_HIGH);
-
- /* Multi-Purpose Pins Functionality configuration */
- static const u32 kwmpp_config[] = {
- MPP0_NF_IO2,
- MPP1_NF_IO3,
- MPP2_NF_IO4,
- MPP3_NF_IO5,
- MPP4_NF_IO6,
- MPP5_NF_IO7,
- MPP6_SYSRST_OUTn,
- MPP7_GPO,
- MPP8_TW_SDA,
- MPP9_TW_SCK,
- MPP10_UART0_TXD,
- MPP11_UART0_RXD,
- MPP12_SD_CLK,
- MPP13_SD_CMD,
- MPP14_SD_D0,
- MPP15_SD_D1,
- MPP16_SD_D2,
- MPP17_SD_D3,
- MPP18_NF_IO0,
- MPP19_NF_IO1,
- MPP20_GE1_0,
- MPP21_GE1_1,
- MPP22_GE1_2,
- MPP23_GE1_3,
- MPP24_GE1_4,
- MPP25_GE1_5,
- MPP26_GE1_6,
- MPP27_GE1_7,
- MPP28_GPIO,
- MPP29_GPIO,
- MPP30_GE1_10,
- MPP31_GE1_11,
- MPP32_GE1_12,
- MPP33_GE1_13,
- MPP34_GPIO,
- MPP35_GPIO,
- MPP36_GPIO,
- MPP37_GPIO,
- MPP38_GPIO,
- MPP39_GPIO,
- MPP40_GPIO,
- MPP41_GPIO,
- MPP42_GPIO,
- MPP43_GPIO,
- MPP44_GPIO,
- MPP45_GPIO,
- MPP46_GPIO,
- MPP47_GPIO,
- MPP48_GPIO,
- MPP49_GPIO,
- 0
- };
- kirkwood_mpp_conf(kwmpp_config, NULL);
-
- return 0;
-}
-
-int board_init(void)
-{
- /*
- * arch number of board
- */
- gd->bd->bi_arch_number = CONFIG_MACH_TYPE;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
-
- return 0;
-}
-
-#ifdef CONFIG_CMD_NET
-
-#define MV88E1116_MAC_CTRL2_REG 21
-#define MV88E1116_PGADR_REG 22
-#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
-#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
-
-static void mv_phy_88e1118_init(char *name)
-{
- u16 reg;
- u16 devadr;
-
- if (miiphy_set_current_dev(name))
- return;
-
- /* command to read PHY dev address */
- if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
- printf("Err..%s could not read PHY dev address\n",
- __func__);
- return;
- }
-
- /*
- * Enable RGMII delay on Tx and Rx for CPU port
- * Ref: sec 4.7.2 of chip datasheet
- */
- miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
- miiphy_read(name, devadr, MV88E1116_MAC_CTRL2_REG, ®);
- reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
- miiphy_write(name, devadr, MV88E1116_MAC_CTRL2_REG, reg);
- miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
-
- /* reset the phy */
- miiphy_reset(name, devadr);
-
- printf("88E1118 Initialized on %s\n", name);
-}
-
-/* Configure and enable Switch and PHY */
-void reset_phy(void)
-{
- /* configure and initialize PHY */
- mv_phy_88e1118_init("egiga0");
-
-}
-#endif
diff --git a/configs/tk71_defconfig b/configs/tk71_defconfig
deleted file mode 100644
index 5e2a0b8..0000000
--- a/configs/tk71_defconfig
+++ /dev/null
@@ -1,6 +0,0 @@
-CONFIG_ARM=y
-CONFIG_KIRKWOOD=y
-CONFIG_TARGET_TK71=y
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_SETEXPR is not set
diff --git a/include/configs/tk71.h b/include/configs/tk71.h
deleted file mode 100644
index 46e8c90..0000000
--- a/include/configs/tk71.h
+++ /dev/null
@@ -1,112 +0,0 @@
-/*
- * Copyright (C) 2012 Marek Vasut <marex at denx.de>
- * on behalf of DENX Software Engineering GmbH
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_TK71_H__
-#define __CONFIG_TK71_H__
-
-/*
- * Version number information
- */
-#define CONFIG_IDENT_STRING "\nKa-Ro TK71"
-
-/*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
-#define CONFIG_KW88F6281 1 /* SOC Name */
-#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-#define CONFIG_NR_DRAM_BANKS 1
-
-#define MACH_TYPE_TK71 2399
-#define CONFIG_MACH_TYPE MACH_TYPE_TK71
-
-/*
- * Commands configuration
- */
-#define CONFIG_SYS_HUSH_PARSER
-
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_DOS_PARTITION
-#define CONFIG_SUPPORT_VFAT
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ENV
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_USB
-
-/*
- * mv-common.h should be defined after CMD configs since it used them
- * to enable certain macros
- */
-#include "mv-common.h"
-
-/*
- * NAND flash
- */
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_MTD_DEVICE
-#define CONFIG_MTD_PARTITIONS
-#define CONFIG_JFFS2_NAND
-#define CONFIG_JFFS2_DEV "nand0,3"
-#endif
-
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS {1, 0}
-#define CONFIG_PHY_BASE_ADR 0x08
-#endif
-
-/*
- * USB/EHCI
- */
-#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_KIRKWOOD
-#define CONFIG_EHCI_IS_TDI
-#define CONFIG_USB_STORAGE
-#endif
-
-/*
- * Environment variables configurations
- */
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#else
-#define CONFIG_ENV_IS_NOWHERE
-#endif
-
-#define CONFIG_ENV_SIZE 0x20000
-#define CONFIG_ENV_ADDR 0x80000
-#define CONFIG_ENV_OFFSET 0x80000
-
-/*
- * Default environment variables
- */
-#define CONFIG_BOOTCOMMAND "nand read 0x800000 kernel 0x300000; bootm;"
-#define CONFIG_MTDPARTS "512K(u-boot),512K(u-boot-env),3M(kernel),-(root)"
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "update_uboot=dhcp u-boot.kwb; nand erase.part u-boot; nand write ${fileaddr} u-boot ${filesize}\0" \
- "update_kernel=dhcp uImage-tk71; nand erase.part kernel; nand write ${fileaddr} kernel ${filesize} \0" \
- "update_rootfs=dhcp rootfs-tk71; nand erase.part root; nand write ${fileaddr} root ${filesize}\0" \
- "update_all=run update_uboot; run update_kernel; run update_rootfs; reset\0" \
- "mtdids=nand0=orion_nand\0" \
- "mtdparts=mtdparts=orion_nand:"CONFIG_MTDPARTS"\0" \
- "bootargs=console=ttyS0,115200 mtdparts=orion_nand:"CONFIG_MTDPARTS" rootfstype=jffs2 root=/dev/mtdblock3 rw\0"
-#define MTDIDS_DEFAULT "nand0=orion_nand"
-#define MTDPARTS_DEFAULT "mtdparts=orion_nand:"CONFIG_MTDPARTS
-
-#define PHYS_SDRAM_1 0x00000000 /* Base address */
-#define PHYS_SDRAM_1_SIZE 0x20000000 /* Max 512 MB RAM */
-
-#endif /* __CONFIG_TK71_H__ */
--
2.5.0.457.gab17608
More information about the U-Boot
mailing list