[U-Boot] [PATCH 37/45] arm: Remove vision2 board
Simon Glass
sjg at chromium.org
Mon Aug 31 03:19:31 CEST 2015
This board has not been converted to generic board by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg at chromium.org>
---
arch/arm/Kconfig | 5 -
board/ttcontrol/vision2/Kconfig | 15 -
board/ttcontrol/vision2/MAINTAINERS | 6 -
board/ttcontrol/vision2/Makefile | 9 -
board/ttcontrol/vision2/imximage_hynix.cfg | 212 -----------
board/ttcontrol/vision2/vision2.c | 572 -----------------------------
configs/vision2_defconfig | 7 -
doc/README.watchdog | 1 +
include/configs/vision2.h | 199 ----------
9 files changed, 1 insertion(+), 1025 deletions(-)
delete mode 100644 board/ttcontrol/vision2/Kconfig
delete mode 100644 board/ttcontrol/vision2/MAINTAINERS
delete mode 100644 board/ttcontrol/vision2/Makefile
delete mode 100644 board/ttcontrol/vision2/imximage_hynix.cfg
delete mode 100644 board/ttcontrol/vision2/vision2.c
delete mode 100644 configs/vision2_defconfig
delete mode 100644 include/configs/vision2.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index e64c0b7..1a440b7 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -463,10 +463,6 @@ config TARGET_MX53SMD
bool "Support mx53smd"
select CPU_V7
-config TARGET_VISION2
- bool "Support vision2"
- select CPU_V7
-
config TARGET_UDOO
bool "Support udoo"
select CPU_V7
@@ -883,7 +879,6 @@ source "board/ti/ti816x/Kconfig"
source "board/timll/devkit3250/Kconfig"
source "board/toradex/colibri_pxa270/Kconfig"
source "board/toradex/colibri_vf/Kconfig"
-source "board/ttcontrol/vision2/Kconfig"
source "board/udoo/Kconfig"
source "board/vpac270/Kconfig"
source "board/vscom/baltos/Kconfig"
diff --git a/board/ttcontrol/vision2/Kconfig b/board/ttcontrol/vision2/Kconfig
deleted file mode 100644
index cacd2c5..0000000
--- a/board/ttcontrol/vision2/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_VISION2
-
-config SYS_BOARD
- default "vision2"
-
-config SYS_VENDOR
- default "ttcontrol"
-
-config SYS_SOC
- default "mx5"
-
-config SYS_CONFIG_NAME
- default "vision2"
-
-endif
diff --git a/board/ttcontrol/vision2/MAINTAINERS b/board/ttcontrol/vision2/MAINTAINERS
deleted file mode 100644
index cfc9903..0000000
--- a/board/ttcontrol/vision2/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-VISION2 BOARD
-M: Stefano Babic <sbabic at denx.de>
-S: Maintained
-F: board/ttcontrol/vision2/
-F: include/configs/vision2.h
-F: configs/vision2_defconfig
diff --git a/board/ttcontrol/vision2/Makefile b/board/ttcontrol/vision2/Makefile
deleted file mode 100644
index c3e1e87..0000000
--- a/board/ttcontrol/vision2/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# Copyright (C) 2007, Guennadi Liakhovetski <lg at denx.de>
-#
-# (C) Copyright 2009 Freescale Semiconductor, Inc.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := vision2.o
diff --git a/board/ttcontrol/vision2/imximage_hynix.cfg b/board/ttcontrol/vision2/imximage_hynix.cfg
deleted file mode 100644
index c74973e..0000000
--- a/board/ttcontrol/vision2/imximage_hynix.cfg
+++ /dev/null
@@ -1,212 +0,0 @@
-/*
- * (C) Copyright 2009
- * Stefano Babic DENX Software Engineering sbabic at denx.de.
- *
- * (C) Copyright 2010
- * Klaus Steinhammer TTECH Control Gmbh kst at tttech.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- *
- * Refer doc/README.imximage for more details about how-to configure
- * and create imximage boot image
- *
- * The syntax is taken as close as possible with the kwbimage
- */
-
-/*
- * Boot Device : one of
- * spi, nand, onenand, sd
- */
-BOOT_FROM spi
-
-/*
- * Device Configuration Data (DCD)
- *
- * Each entry must have the format:
- * Addr-type Address Value
- *
- * where:
- * Addr-type register length (1,2 or 4 bytes)
- * Address absolute address of the register
- * value value to be stored in the register
- */
-
-/*
- * #######################
- * ### Disable WDOG ###
- * #######################
- */
-DATA 2 0x73f98000 0x30
-
-/*
- * #######################
- * ### SET DDR Clk ###
- * #######################
- */
-/* CCM: CBMCR - ddr_clk_sel: axi_b (133MHz) */
-DATA 4 0x73FD4018 0x000024C0
-
-/* DOUBLE SPI CLK (13MHz->26 MHz Clock) */
-DATA 4 0x73FD4038 0x2010241
-
-/* IOMUXC_SW_PAD_CTL_PAD_CSPI1_MOSI HYS_ENABLE | DRV_MAX | SRE_FAST */
-DATA 4 0x73fa8600 0x00000107
-/* IOMUXC_SW_PAD_CTL_PAD_CSPI1_MISO HYS_ENABLE | DRV_MAX | SRE_FAST */
-DATA 4 0x73fa8604 0x00000107
-/* IOMUXC_SW_PAD_CTL_PAD_CSPI1_SS0 HYS_ENABLE | PKE_ENABLE | DRV_MAX | SRE_FAST */
-DATA 4 0x73fa8608 0x00000187
-/* IOMUXC_SW_PAD_CTL_PAD_CSPI1_SS1 HYS_ENABLE | PKE_ENABLE | DRV_MAX | SRE_FAST */
-DATA 4 0x73fa860c 0x00000187
-/* IOMUXC_SW_PAD_CTL_PAD_CSPI1_SCLK HYS_ENABLE | DRV_MAX | SRE_FAST */
-DATA 4 0x73fa8614 0x00000107
-/* IOMUXC_SW_PAD_CTL_PAD_DI1_PIN11 HYS_ENABLE | DRV_MAX | SRE_FAST (CSPI1_SS2) */
-DATA 4 0x73fa86a8 0x00000187
-
-/*
- * #######################
- * ### Settings IOMUXC ###
- * #######################
- */
-/*
- * DDR IOMUX configuration
- * Control, Data, Address pads are in their default state: HIGH DS, FAST SR.
- * IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK MAX DS
- */
-DATA 4 0x73fa84b8 0x000000e7
-/* PVTC MAX (at GPC, PGR reg) */
-/* DATA 4 0x73FD8004 0x1fc00000 */
-
-/* DQM0 DS high slew rate slow */
-DATA 4 0x73fa84d4 0x000000e4
-/* DQM1 DS high slew rate slow */
-DATA 4 0x73fa84d8 0x000000e4
-/* DQM2 DS high slew rate slow */
-DATA 4 0x73fa84dc 0x000000e4
-/* DQM3 DS high slew rate slow */
-DATA 4 0x73fa84e0 0x000000e4
-
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0 DS high & SLEW slow */
-DATA 4 0x73fa84bc 0x000000c4
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1 DS high & SLEW slow */
-DATA 4 0x73fa84c0 0x000000c4
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS2 DS high & SLEW slow */
-DATA 4 0x73fa84c4 0x000000c4
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS3 DS high & SLEW slow */
-DATA 4 0x73fa84c8 0x000000c4
-
-/* DRAM_DATA B0 */
-DATA 4 0x73fa88a4 0x00000004
-/* DRAM_DATA B1 */
-DATA 4 0x73fa88ac 0x00000004
-/* DRAM_DATA B2 */
-DATA 4 0x73fa88b8 0x00000004
-/* DRAM_DATA B3 */
-DATA 4 0x73fa882c 0x00000004
-
-/* DRAM_DATA B0 slew rate */
-DATA 4 0x73fa8878 0x00000000
-/* DRAM_DATA B1 slew rate */
-DATA 4 0x73fa8880 0x00000000
-/* DRAM_DATA B2 slew rate */
-DATA 4 0x73fa888c 0x00000000
-/* DRAM_DATA B3 slew rate */
-DATA 4 0x73fa889c 0x00000000
-
-/*
- * #######################
- * ### Configure SDRAM ###
- * #######################
- */
-
-/* Configure CS0 */
-/* ####################### */
-
-/* ESDCTL0: Enable controller */
-DATA 4 0x83fd9000 0x83220000
-
-/* Init DRAM on CS0 */
-/* ESDSCR: Precharge command */
-DATA 4 0x83fd9014 0x04008008
-/* ESDSCR: Refresh command */
-DATA 4 0x83fd9014 0x00008010
-/* ESDSCR: Refresh command */
-DATA 4 0x83fd9014 0x00008010
-/* ESDSCR: LMR with CAS=3 and BL=3 (Burst Length = 8) */
-DATA 4 0x83fd9014 0x00338018
-/* ESDSCR: EMR with half Drive strength (= medium strength @ i.MX51) */
-DATA 4 0x83fd9014 0x0020801a
-/* ESDSCR */
-DATA 4 0x83fd9014 0x00008000
-
-/* ESDSCR: EMR with full Drive strength */
-/* DATA 4 0x83fd9014 0x0000801a */
-
-/* ESDCTL0: 14 ROW, 10 COL, 32Bit, SREF=8 */
-DATA 4 0x83fd9000 0xC3220000
-
-/*
- * ESDCFG0: tRFC:22clks, tXSR:28clks, tXP:2clks, tWTR:2clk, tRP:3clks, tMRD:2clks
- * tRAS:8clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:11clks
- * DATA 4 0x83fd9004 0xC33574AA
- */
-/*
- * micron mDDR
- * ESDCFG0: tRFC:11clks, tXSR:19clks, tXP:1clks, tWTR:2clk, tRP:3clks, tMRD:2clks
- * tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks
- * DATA 4 0x83FD9004 0x101564a8
- */
-/*
- * hynix mDDR
- * ESDCFG0: tRFC:17clks, tXSR:21clks, tXP:3clks, tWTR:1clk, tRP:3clks, tMRD:2clks
- * tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks
- */
-DATA 4 0x83FD9004 0x704564a8
-
-/* ESDMISC: AP=10, Bank interleaving on, MIF3 en, RALAT=2 */
-DATA 4 0x83fd9010 0x000a1700
-
-/* Configure CS1 */
-/* ####################### */
-
-/* ESDCTL1: Enable controller */
-DATA 4 0x83fd9008 0x83220000
-
-/* Init DRAM on CS1 */
-/* ESDSCR: Precharge command */
-DATA 4 0x83fd9014 0x0400800c
-/* ESDSCR: Refresh command */
-DATA 4 0x83fd9014 0x00008014
-/* ESDSCR: Refresh command */
-DATA 4 0x83fd9014 0x00008014
-/* ESDSCR: LMR with CAS=3 and BL=3 (Burst Length = 8) */
-DATA 4 0x83fd9014 0x0033801c
-/* ESDSCR: EMR with half Drive strength (= medium strength @ i.MX51) */
-DATA 4 0x83fd9014 0x0020801e
-/* ESDSCR */
-DATA 4 0x83fd9014 0x00008004
-
-/* ESDCTL1: 14 ROW, 10 COL, 32Bit, SREF=8 */
-DATA 4 0x83fd9008 0xC3220000
-/*
- * ESDCFG1: tRFC:22clks, tXSR:28clks, tXP:2clks, tWTR:2clk, tRP:3clks, tMRD:2clks
- * tRAS:8clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:11clks
- * DATA 4 0x83fd900c 0xC33574AA
- */
-/*
- * micron mDDR
- * ESDCFG1: tRFC:11clks, tXSR:19clks, tXP:1clks, tWTR:2clk, tRP:3clks, tMRD:2clks
- * tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks
- * DATA 4 0x83FD900C 0x101564a8
- */
-/*
- * hynix mDDR
- * ESDCFG0: tRFC:17clks, tXSR:21clks, tXP:3clks, tWTR:1clk, tRP:3clks, tMRD:2clks
- * tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks
- */
-DATA 4 0x83FD900C 0x704564a8
-
-/* ESDSCR (mDRAM configuration finished) */
-DATA 4 0x83FD9014 0x00000004
-
-/* ESDSCR - clear "configuration request" bit */
-DATA 4 0x83fd9014 0x00000000
diff --git a/board/ttcontrol/vision2/vision2.c b/board/ttcontrol/vision2/vision2.c
deleted file mode 100644
index 247991d..0000000
--- a/board/ttcontrol/vision2/vision2.c
+++ /dev/null
@@ -1,572 +0,0 @@
-/*
- * (C) Copyright 2010
- * Stefano Babic, DENX Software Engineering, sbabic at denx.de.
- *
- * (C) Copyright 2009 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/iomux-mx51.h>
-#include <asm/gpio.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/imx-common/spi.h>
-#include <i2c.h>
-#include <mmc.h>
-#include <power/pmic.h>
-#include <fsl_esdhc.h>
-#include <fsl_pmic.h>
-#include <mc13892.h>
-#include <linux/fb.h>
-
-#include <ipu_pixfmt.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static struct fb_videomode const nec_nl6448bc26_09c = {
- "NEC_NL6448BC26-09C",
- 60, /* Refresh */
- 640, /* xres */
- 480, /* yres */
- 37650, /* pixclock = 26.56Mhz */
- 48, /* left margin */
- 16, /* right margin */
- 31, /* upper margin */
- 12, /* lower margin */
- 96, /* hsync-len */
- 2, /* vsync-len */
- 0, /* sync */
- FB_VMODE_NONINTERLACED, /* vmode */
- 0, /* flag */
-};
-
-#ifdef CONFIG_HW_WATCHDOG
-#include <watchdog.h>
-void hw_watchdog_reset(void)
-{
- int val;
-
- /* toggle watchdog trigger pin */
- val = gpio_get_value(IMX_GPIO_NR(3, 2));
- val = val ? 0 : 1;
- gpio_set_value(IMX_GPIO_NR(3, 2), val);
-}
-#endif
-
-static void init_drive_strength(void)
-{
- static const iomux_v3_cfg_t ddr_pads[] = {
- NEW_PAD_CTRL(MX51_GRP_PKEDDR, 0),
- NEW_PAD_CTRL(MX51_GRP_PKEADDR, PAD_CTL_PKE),
- NEW_PAD_CTRL(MX51_GRP_DDRAPKS, 0),
- NEW_PAD_CTRL(MX51_GRP_DDRAPUS, PAD_CTL_PUS_100K_UP),
- NEW_PAD_CTRL(MX51_GRP_DDR_SR_A1, PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_GRP_DDR_A0, PAD_CTL_DSE_HIGH),
- NEW_PAD_CTRL(MX51_GRP_DDR_A1, PAD_CTL_DSE_HIGH),
- NEW_PAD_CTRL(MX51_PAD_DRAM_RAS__DRAM_RAS,
- PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_DRAM_CAS__DRAM_CAS,
- PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_GRP_PKEDDR, PAD_CTL_PKE),
- NEW_PAD_CTRL(MX51_GRP_DDRPKS, 0),
- NEW_PAD_CTRL(MX51_GRP_HYSDDR0, 0),
- NEW_PAD_CTRL(MX51_GRP_HYSDDR1, 0),
- NEW_PAD_CTRL(MX51_GRP_HYSDDR2, 0),
- NEW_PAD_CTRL(MX51_GRP_HYSDDR3, 0),
- NEW_PAD_CTRL(MX51_GRP_DRAM_SR_B0, PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_GRP_DRAM_SR_B1, PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_GRP_DRAM_SR_B2, PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_GRP_DRAM_SR_B4, PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_GRP_DDRPUS, PAD_CTL_PUS_100K_UP),
- NEW_PAD_CTRL(MX51_GRP_INMODE1, 0),
- NEW_PAD_CTRL(MX51_GRP_DRAM_B0, PAD_CTL_DSE_MED),
- NEW_PAD_CTRL(MX51_GRP_DRAM_B1, PAD_CTL_DSE_MED),
- NEW_PAD_CTRL(MX51_GRP_DRAM_B2, PAD_CTL_DSE_MED),
- NEW_PAD_CTRL(MX51_GRP_DRAM_B4, PAD_CTL_DSE_MED),
-
- NEW_PAD_CTRL(MX51_PAD_DRAM_SDWE__DRAM_SDWE, MX51_GPIO_PAD_CTRL),
- NEW_PAD_CTRL(MX51_PAD_DRAM_SDCKE0__DRAM_SDCKE0,
- MX51_GPIO_PAD_CTRL),
- NEW_PAD_CTRL(MX51_PAD_DRAM_SDCKE1__DRAM_SDCKE1,
- MX51_GPIO_PAD_CTRL),
- NEW_PAD_CTRL(MX51_PAD_DRAM_SDCLK__DRAM_SDCLK,
- MX51_GPIO_PAD_CTRL),
- NEW_PAD_CTRL(MX51_PAD_DRAM_SDQS0__DRAM_SDQS0,
- MX51_GPIO_PAD_CTRL),
- NEW_PAD_CTRL(MX51_PAD_DRAM_SDQS1__DRAM_SDQS1,
- MX51_GPIO_PAD_CTRL),
- NEW_PAD_CTRL(MX51_PAD_DRAM_SDQS2__DRAM_SDQS2,
- MX51_GPIO_PAD_CTRL),
- NEW_PAD_CTRL(MX51_PAD_DRAM_SDQS3__DRAM_SDQS3,
- MX51_GPIO_PAD_CTRL),
- NEW_PAD_CTRL(MX51_PAD_DRAM_CS0__DRAM_CS0, MX51_GPIO_PAD_CTRL),
- NEW_PAD_CTRL(MX51_PAD_DRAM_CS1__DRAM_CS1, MX51_GPIO_PAD_CTRL),
- NEW_PAD_CTRL(MX51_PAD_DRAM_DQM0__DRAM_DQM0, MX51_GPIO_PAD_CTRL),
- NEW_PAD_CTRL(MX51_PAD_DRAM_DQM1__DRAM_DQM1, MX51_GPIO_PAD_CTRL),
- NEW_PAD_CTRL(MX51_PAD_DRAM_DQM2__DRAM_DQM2, MX51_GPIO_PAD_CTRL),
- NEW_PAD_CTRL(MX51_PAD_DRAM_DQM3__DRAM_DQM3, MX51_GPIO_PAD_CTRL),
- };
-
- imx_iomux_v3_setup_multiple_pads(ddr_pads, ARRAY_SIZE(ddr_pads));
-}
-
-int dram_init(void)
-{
- gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1,
- PHYS_SDRAM_1_SIZE);
-
- return 0;
-}
-
-static void setup_weim(void)
-{
- struct weim *pweim = (struct weim *)WEIM_BASE_ADDR;
-
- pweim->cs0gcr1 = 0x004100b9;
- pweim->cs0gcr2 = 0x00000001;
- pweim->cs0rcr1 = 0x0a018000;
- pweim->cs0rcr2 = 0;
- pweim->cs0wcr1 = 0x0704a240;
-}
-
-static void setup_uart(void)
-{
- static const iomux_v3_cfg_t uart_pads[] = {
- MX51_PAD_EIM_D25__UART3_RXD, /* console RX */
- MX51_PAD_EIM_D26__UART3_TXD, /* console TX */
- };
-
- imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
-}
-
-#ifdef CONFIG_MXC_SPI
-int board_spi_cs_gpio(unsigned bus, unsigned cs)
-{
- return (bus == 0 && cs == 1) ? 121 : -1;
-}
-
-void spi_io_init(void)
-{
- static const iomux_v3_cfg_t spi_pads[] = {
- NEW_PAD_CTRL(MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI, PAD_CTL_HYS |
- PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_CSPI1_MISO__ECSPI1_MISO, PAD_CTL_HYS |
- PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_CSPI1_SS0__ECSPI1_SS0, PAD_CTL_HYS |
- PAD_CTL_PKE | PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_CSPI1_SS1__ECSPI1_SS1, PAD_CTL_HYS |
- PAD_CTL_PKE | PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_DI1_PIN11__ECSPI1_SS2, PAD_CTL_HYS |
- PAD_CTL_PKE | PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK, PAD_CTL_HYS |
- PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
- };
-
- imx_iomux_v3_setup_multiple_pads(spi_pads, ARRAY_SIZE(spi_pads));
-}
-
-static void reset_peripherals(int reset)
-{
-#ifdef CONFIG_VISION2_HW_1_0
- static const iomux_v3_cfg_t fec_cfg_pads[] = {
- /* RXD1 */
- NEW_PAD_CTRL(MX51_PAD_EIM_EB3__GPIO2_23, NO_PAD_CTRL),
- /* RXD2 */
- NEW_PAD_CTRL(MX51_PAD_EIM_CS2__GPIO2_27, NO_PAD_CTRL),
- /* RXD3 */
- NEW_PAD_CTRL(MX51_PAD_EIM_CS3__GPIO2_28, NO_PAD_CTRL),
- /* RXER */
- NEW_PAD_CTRL(MX51_PAD_EIM_CS4__GPIO2_29, NO_PAD_CTRL),
- /* COL */
- NEW_PAD_CTRL(MX51_PAD_NANDF_RB2__GPIO3_10, NO_PAD_CTRL),
- /* RCLK */
- NEW_PAD_CTRL(MX51_PAD_NANDF_RB3__GPIO3_11, NO_PAD_CTRL),
- /* RXD0 */
- NEW_PAD_CTRL(MX51_PAD_NANDF_D9__GPIO3_31, NO_PAD_CTRL),
- };
-
- static const iomux_v3_cfg_t fec_pads[] = {
- NEW_PAD_CTRL(MX51_PAD_EIM_CS3__FEC_RDATA3, MX51_PAD_CTRL_2),
- NEW_PAD_CTRL(MX51_PAD_EIM_CS2__FEC_RDATA2, MX51_PAD_CTRL_2),
- NEW_PAD_CTRL(MX51_PAD_EIM_EB3__FEC_RDATA1, MX51_PAD_CTRL_2),
- MX51_PAD_NANDF_D9__FEC_RDATA0,
- NEW_PAD_CTRL(MX51_PAD_NANDF_RB3__FEC_RX_CLK, MX51_PAD_CTRL_4),
- MX51_PAD_EIM_CS4__FEC_RX_ER,
- NEW_PAD_CTRL(MX51_PAD_NANDF_RB2__FEC_COL, MX51_PAD_CTRL_4),
- };
-#endif
-
- if (reset) {
-
- /* reset_n is on NANDF_D15 */
- gpio_direction_output(IMX_GPIO_NR(3, 25), 0);
-
-#ifdef CONFIG_VISION2_HW_1_0
- /*
- * set FEC Configuration lines
- * set levels of FEC config lines
- */
- gpio_direction_output(IMX_GPIO_NR(3, 11), 0);
- gpio_direction_output(IMX_GPIO_NR(3, 10), 1);
- gpio_direction_output(IMX_GPIO_NR(3, 31), 1);
-
- /* set direction of FEC config lines */
- gpio_direction_output(IMX_GPIO_NR(2, 27), 0);
- gpio_direction_output(IMX_GPIO_NR(2, 28), 0);
- gpio_direction_output(IMX_GPIO_NR(2, 29), 0);
- gpio_direction_output(IMX_GPIO_NR(2, 23), 1);
-
- imx_iomux_v3_setup_multiple_pads(fec_cfg_pads,
- ARRAY_SIZE(fec_cfg_pads));
-#endif
-
- /* activate reset_n pin */
- imx_iomux_v3_setup_pad(
- NEW_PAD_CTRL(MX51_PAD_NANDF_D15__GPIO3_25,
- PAD_CTL_DSE_MAX));
- } else {
- /* set FEC Control lines */
- gpio_direction_input(IMX_GPIO_NR(3, 25));
- udelay(500);
-
-#ifdef CONFIG_VISION2_HW_1_0
- imx_iomux_v3_setup_multiple_pads(fec_pads,
- ARRAY_SIZE(fec_pads));
-#endif
- }
-}
-
-static void power_init_mx51(void)
-{
- unsigned int val;
- struct pmic *p;
- int ret;
-
- ret = pmic_init(I2C_PMIC);
- if (ret)
- return;
-
- p = pmic_get("FSL_PMIC");
- if (!p)
- return;
-
- /* Write needed to Power Gate 2 register */
- pmic_reg_read(p, REG_POWER_MISC, &val);
-
- /* enable VCAM with 2.775V to enable read from PMIC */
- val = VCAMCONFIG | VCAMEN;
- pmic_reg_write(p, REG_MODE_1, val);
-
- /*
- * Set switchers in Auto in NORMAL mode & STANDBY mode
- * Setup the switcher mode for SW1 & SW2
- */
- pmic_reg_read(p, REG_SW_4, &val);
- val = (val & ~((SWMODE_MASK << SWMODE1_SHIFT) |
- (SWMODE_MASK << SWMODE2_SHIFT)));
- val |= (SWMODE_AUTO_AUTO << SWMODE1_SHIFT) |
- (SWMODE_AUTO_AUTO << SWMODE2_SHIFT);
- pmic_reg_write(p, REG_SW_4, val);
-
- /* Setup the switcher mode for SW3 & SW4 */
- pmic_reg_read(p, REG_SW_5, &val);
- val &= ~((SWMODE_MASK << SWMODE4_SHIFT) |
- (SWMODE_MASK << SWMODE3_SHIFT));
- val |= (SWMODE_AUTO_AUTO << SWMODE4_SHIFT) |
- (SWMODE_AUTO_AUTO << SWMODE3_SHIFT);
- pmic_reg_write(p, REG_SW_5, val);
-
-
- /* Set VGEN3 to 1.8V, VCAM to 3.0V */
- pmic_reg_read(p, REG_SETTING_0, &val);
- val &= ~(VCAM_MASK | VGEN3_MASK);
- val |= VCAM_3_0;
- pmic_reg_write(p, REG_SETTING_0, val);
-
- /* Set VVIDEO to 2.775V, VAUDIO to 3V0, VSD to 1.8V */
- pmic_reg_read(p, REG_SETTING_1, &val);
- val &= ~(VVIDEO_MASK | VSD_MASK | VAUDIO_MASK);
- val |= VVIDEO_2_775 | VAUDIO_3_0 | VSD_1_8;
- pmic_reg_write(p, REG_SETTING_1, val);
-
- /* Configure VGEN3 and VCAM regulators to use external PNP */
- val = VGEN3CONFIG | VCAMCONFIG;
- pmic_reg_write(p, REG_MODE_1, val);
- udelay(200);
-
- /* Enable VGEN3, VCAM, VAUDIO, VVIDEO, VSD regulators */
- val = VGEN3EN | VGEN3CONFIG | VCAMEN | VCAMCONFIG |
- VVIDEOEN | VAUDIOEN | VSDEN;
- pmic_reg_write(p, REG_MODE_1, val);
-
- pmic_reg_read(p, REG_POWER_CTL2, &val);
- val |= WDIRESET;
- pmic_reg_write(p, REG_POWER_CTL2, val);
-
- udelay(2500);
-
-}
-#endif
-
-static void setup_gpios(void)
-{
- static const iomux_v3_cfg_t gpio_pads_1[] = {
- NEW_PAD_CTRL(MX51_PAD_GPIO1_7__GPIO1_7, PAD_CTL_PKE |
- PAD_CTL_DSE_MED), /* CAM_SUP_DISn */
- NEW_PAD_CTRL(MX51_PAD_DI1_PIN12__GPIO3_1, PAD_CTL_PKE |
- PAD_CTL_DSE_MED), /* DAB Display EN */
- NEW_PAD_CTRL(MX51_PAD_DI1_PIN13__GPIO3_2, PAD_CTL_PKE |
- PAD_CTL_DSE_MED), /* WDOG_TRIGGER */
- };
-
- static const iomux_v3_cfg_t gpio_pads_2[] = {
- NEW_PAD_CTRL(MX51_PAD_DI1_D0_CS__GPIO3_3, PAD_CTL_PKE |
- PAD_CTL_DSE_MED), /* Display2 TxEN */
- NEW_PAD_CTRL(MX51_PAD_DI1_D1_CS__GPIO3_4, PAD_CTL_PKE |
- PAD_CTL_DSE_MED), /* DAB Light EN */
- NEW_PAD_CTRL(MX51_PAD_DISPB2_SER_DIN__GPIO3_5, PAD_CTL_PKE |
- PAD_CTL_DSE_MED), /* AUDIO_MUTE */
- NEW_PAD_CTRL(MX51_PAD_DISPB2_SER_DIO__GPIO3_6, PAD_CTL_PKE |
- PAD_CTL_DSE_MED), /* SPARE_OUT */
- NEW_PAD_CTRL(MX51_PAD_NANDF_D14__GPIO3_26, PAD_CTL_PKE |
- PAD_CTL_DSE_MED), /* BEEPER_EN */
- NEW_PAD_CTRL(MX51_PAD_NANDF_D13__GPIO3_27, PAD_CTL_PKE |
- PAD_CTL_DSE_MED), /* POWER_OFF */
- NEW_PAD_CTRL(MX51_PAD_NANDF_D10__GPIO3_30, PAD_CTL_PKE |
- PAD_CTL_DSE_MED), /* FRAM_WE */
- NEW_PAD_CTRL(MX51_PAD_CSPI1_RDY__GPIO4_26, PAD_CTL_PKE |
- PAD_CTL_DSE_MED), /* EXPANSION_EN */
- MX51_PAD_GPIO1_2__PWM1_PWMO,
- };
-
- unsigned int i;
-
- imx_iomux_v3_setup_multiple_pads(gpio_pads_1, ARRAY_SIZE(gpio_pads_1));
-
- /* Now we need to trigger the watchdog */
- WATCHDOG_RESET();
-
- imx_iomux_v3_setup_multiple_pads(gpio_pads_2, ARRAY_SIZE(gpio_pads_2));
-
- /*
- * Set GPIO1_4 to high and output; it is used to reset
- * the system on reboot
- */
- gpio_direction_output(IMX_GPIO_NR(1, 4), 1);
-
- gpio_direction_output(IMX_GPIO_NR(1, 7), 0);
- for (i = IMX_GPIO_NR(3, 1); i < IMX_GPIO_NR(3, 7); i++)
- gpio_direction_output(i, 0);
-
- gpio_direction_output(IMX_GPIO_NR(3, 30), 0);
-
- /* Set POWER_OFF high */
- gpio_direction_output(IMX_GPIO_NR(3, 27), 1);
-
- gpio_direction_output(IMX_GPIO_NR(3, 26), 0);
-
- gpio_direction_output(IMX_GPIO_NR(4, 26), 0);
-
- gpio_direction_output(IMX_GPIO_NR(4, 25), 1);
-
- WATCHDOG_RESET();
-}
-
-static void setup_fec(void)
-{
- static const iomux_v3_cfg_t fec_pads[] = {
- NEW_PAD_CTRL(MX51_PAD_EIM_EB2__FEC_MDIO, PAD_CTL_HYS |
- PAD_CTL_PUS_22K_UP | PAD_CTL_ODE |
- PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
- MX51_PAD_NANDF_CS3__FEC_MDC,
- NEW_PAD_CTRL(MX51_PAD_EIM_CS3__FEC_RDATA3, MX51_PAD_CTRL_2),
- NEW_PAD_CTRL(MX51_PAD_EIM_CS2__FEC_RDATA2, MX51_PAD_CTRL_2),
- NEW_PAD_CTRL(MX51_PAD_EIM_EB3__FEC_RDATA1, MX51_PAD_CTRL_2),
- MX51_PAD_NANDF_D9__FEC_RDATA0,
- MX51_PAD_NANDF_CS6__FEC_TDATA3,
- MX51_PAD_NANDF_CS5__FEC_TDATA2,
- MX51_PAD_NANDF_CS4__FEC_TDATA1,
- MX51_PAD_NANDF_D8__FEC_TDATA0,
- MX51_PAD_NANDF_CS7__FEC_TX_EN,
- MX51_PAD_NANDF_CS2__FEC_TX_ER,
- MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK,
- NEW_PAD_CTRL(MX51_PAD_NANDF_RB2__FEC_COL, MX51_PAD_CTRL_4),
- NEW_PAD_CTRL(MX51_PAD_NANDF_RB3__FEC_RX_CLK, MX51_PAD_CTRL_4),
- MX51_PAD_EIM_CS5__FEC_CRS,
- MX51_PAD_EIM_CS4__FEC_RX_ER,
- NEW_PAD_CTRL(MX51_PAD_NANDF_D11__FEC_RX_DV, MX51_PAD_CTRL_4),
- };
-
- imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
-}
-
-struct fsl_esdhc_cfg esdhc_cfg[1] = {
- {MMC_SDHC1_BASE_ADDR},
-};
-
-int get_mmc_getcd(u8 *cd, struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-
- if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
- *cd = gpio_get_value(IMX_GPIO_NR(1, 0));
- else
- *cd = 0;
-
- return 0;
-}
-
-#ifdef CONFIG_FSL_ESDHC
-int board_mmc_init(bd_t *bis)
-{
- static const iomux_v3_cfg_t sd1_pads[] = {
- NEW_PAD_CTRL(MX51_PAD_SD1_CMD__SD1_CMD, PAD_CTL_DSE_MAX |
- PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_SD1_CLK__SD1_CLK, PAD_CTL_DSE_MAX |
- PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_SD1_DATA0__SD1_DATA0, PAD_CTL_DSE_MAX |
- PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_SD1_DATA1__SD1_DATA1, PAD_CTL_DSE_MAX |
- PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_SD1_DATA2__SD1_DATA2, PAD_CTL_DSE_MAX |
- PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_SD1_DATA3__SD1_DATA3, PAD_CTL_DSE_MAX |
- PAD_CTL_HYS | PAD_CTL_PUS_100K_DOWN | PAD_CTL_SRE_FAST),
- NEW_PAD_CTRL(MX51_PAD_GPIO1_0__SD1_CD, PAD_CTL_HYS),
- NEW_PAD_CTRL(MX51_PAD_GPIO1_1__SD1_WP, PAD_CTL_HYS),
- };
-
- imx_iomux_v3_setup_multiple_pads(sd1_pads, ARRAY_SIZE(sd1_pads));
-
- esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
- return fsl_esdhc_initialize(bis, &esdhc_cfg[0]);
-}
-#endif
-
-void lcd_enable(void)
-{
- static const iomux_v3_cfg_t lcd_pads[] = {
- MX51_PAD_DI1_PIN2__DI1_PIN2,
- MX51_PAD_DI1_PIN3__DI1_PIN3,
- };
-
- int ret;
-
- imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
-
- gpio_set_value(IMX_GPIO_NR(1, 2), 1);
- imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_GPIO1_2__GPIO1_2,
- NO_PAD_CTRL));
-
- ret = ipuv3_fb_init(&nec_nl6448bc26_09c, 0, IPU_PIX_FMT_RGB666);
- if (ret)
- puts("LCD cannot be configured\n");
-}
-
-int board_early_init_f(void)
-{
-
-
- init_drive_strength();
-
- /* Setup debug led */
- gpio_direction_output(IMX_GPIO_NR(1, 6), 0);
- imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_GPIO1_6__GPIO1_6,
- PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST));
-
- /* wait a little while to give the pll time to settle */
- sdelay(100000);
-
- setup_weim();
- setup_uart();
- setup_fec();
- setup_gpios();
-
- spi_io_init();
-
- return 0;
-}
-
-static void backlight(int on)
-{
- if (on) {
- gpio_set_value(IMX_GPIO_NR(3, 1), 1);
- udelay(10000);
- gpio_set_value(IMX_GPIO_NR(3, 4), 1);
- } else {
- gpio_set_value(IMX_GPIO_NR(3, 1), 0);
- gpio_set_value(IMX_GPIO_NR(3, 4), 0);
- }
-}
-
-int board_init(void)
-{
- /* address of boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
- lcd_enable();
-
- backlight(1);
-
- return 0;
-}
-
-int board_late_init(void)
-{
- power_init_mx51();
-
- reset_peripherals(1);
- udelay(2000);
- reset_peripherals(0);
- udelay(2000);
-
- /* Early revisions require a second reset */
-#ifdef CONFIG_VISION2_HW_1_0
- reset_peripherals(1);
- udelay(2000);
- reset_peripherals(0);
- udelay(2000);
-#endif
-
- return 0;
-}
-
-/*
- * Do not overwrite the console
- * Use always serial for U-Boot console
- */
-int overwrite_console(void)
-{
- return 1;
-}
-
-int checkboard(void)
-{
- puts("Board: TTControl Vision II CPU V\n");
-
- return 0;
-}
-
-int do_vision_lcd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- int on;
-
- if (argc < 2)
- return cmd_usage(cmdtp);
-
- on = (strcmp(argv[1], "on") == 0);
- backlight(on);
-
- return 0;
-}
-
-U_BOOT_CMD(
- lcdbl, CONFIG_SYS_MAXARGS, 1, do_vision_lcd,
- "Vision2 Backlight",
- "lcdbl [on|off]\n"
-);
diff --git a/configs/vision2_defconfig b/configs/vision2_defconfig
deleted file mode 100644
index 962dc5b..0000000
--- a/configs/vision2_defconfig
+++ /dev/null
@@ -1,7 +0,0 @@
-CONFIG_ARM=y
-CONFIG_TARGET_VISION2=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/ttcontrol/vision2/imximage_hynix.cfg"
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_SPI_FLASH=y
-CONFIG_SYS_PROMPT="Vision II U-boot > "
diff --git a/doc/README.watchdog b/doc/README.watchdog
index 59f306b..b66fd6c 100644
--- a/doc/README.watchdog
+++ b/doc/README.watchdog
@@ -27,6 +27,7 @@ CONFIG_IMX_WATCHDOG
Available for i.mx31/35/5x/6x to service the watchdog. This is not
automatically set because some boards (vision2) still need to define
their own hw_watchdog_reset routine.
+ TODO: vision2 is removed now, so perhaps this can be changed.
CONFIG_XILINX_TB_WATCHDOG
Available for Xilinx Axi platforms to service timebase watchdog timer.
diff --git a/include/configs/vision2.h b/include/configs/vision2.h
deleted file mode 100644
index b43373f..0000000
--- a/include/configs/vision2.h
+++ /dev/null
@@ -1,199 +0,0 @@
-/*
- * Copyright (C) 2007, Guennadi Liakhovetski <lg at denx.de>
- *
- * (C) Copyright 2009 Freescale Semiconductor, Inc.
- *
- * Configuration settings for the MX51-3Stack Freescale board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-
-#define CONFIG_MX51 /* in a mx51 */
-#define CONFIG_SYS_TEXT_BASE 0x97800000
-
-#include <asm/arch/imx-regs.h>
-
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DISPLAY_BOARDINFO
-
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_BOARD_LATE_INIT
-
-#ifndef MACH_TYPE_TTC_VISION2
-#define MACH_TYPE_TTC_VISION2 2775
-#endif
-#define CONFIG_MACH_TYPE MACH_TYPE_TTC_VISION2
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
-
-/*
- * Hardware drivers
- */
-#define CONFIG_MXC_UART
-#define CONFIG_MXC_UART_BASE UART3_BASE
-#define CONFIG_MXC_GPIO
-#define CONFIG_MXC_SPI
-#define CONFIG_HW_WATCHDOG
-
- /*
- * SPI Configs
- * */
-#define CONFIG_FSL_SF
-#define CONFIG_CMD_SF
-
-#define CONFIG_SPI_FLASH_STMICRO
-
-/*
- * Use gpio 4 pin 25 as chip select for SPI flash
- * This corresponds to gpio 121
- */
-#define CONFIG_SF_DEFAULT_CS 1
-#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
-#define CONFIG_SF_DEFAULT_SPEED 25000000
-
-#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
-#define CONFIG_ENV_SPI_BUS 0
-#define CONFIG_ENV_SPI_MAX_HZ 25000000
-#define CONFIG_ENV_SPI_MODE SPI_MODE_0
-
-#define CONFIG_ENV_OFFSET (6 * 64 * 1024)
-#define CONFIG_ENV_SECT_SIZE (1 * 64 * 1024)
-#define CONFIG_ENV_SIZE (4 * 1024)
-
-#define CONFIG_FSL_ENV_IN_SF
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-
-/* PMIC Controller */
-#define CONFIG_POWER
-#define CONFIG_POWER_SPI
-#define CONFIG_POWER_FSL
-#define CONFIG_FSL_PMIC_BUS 0
-#define CONFIG_FSL_PMIC_CS 0
-#define CONFIG_FSL_PMIC_CLK 2500000
-#define CONFIG_FSL_PMIC_MODE SPI_MODE_0
-#define CONFIG_FSL_PMIC_BITLEN 32
-#define CONFIG_RTC_MC13XXX
-
-/*
- * MMC Configs
- */
-#define CONFIG_FSL_ESDHC
-#ifdef CONFIG_FSL_ESDHC
-#define CONFIG_SYS_FSL_ESDHC_ADDR (0x70004000)
-#define CONFIG_SYS_FSL_ESDHC_NUM 1
-
-#define CONFIG_MMC
-
-#define CONFIG_CMD_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-
-#define CONFIG_CMD_DATE
-
-/*
- * Eth Configs
- */
-#define CONFIG_HAS_ETH1
-#define CONFIG_MII
-
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE FEC_BASE_ADDR
-#define CONFIG_FEC_MXC_PHYADDR 0x1F
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_MII
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_CONS_INDEX 3
-#define CONFIG_BAUDRATE 115200
-
-/***********************************************************
- * Command definition
- ***********************************************************/
-
-#define CONFIG_CMD_SPI
-
-#define CONFIG_BOOTDELAY 3
-
-#define CONFIG_LOADADDR 0x90800000 /* loadaddr env var */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "loadaddr=0x90800000\0"
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 64 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-#define CONFIG_SYS_MEMTEST_START 0x90000000
-#define CONFIG_SYS_MEMTEST_END 0x10000
-
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 2
-#define PHYS_SDRAM_1 CSD0_BASE_ADDR
-#define PHYS_SDRAM_1_SIZE (256 * 1024 * 1024)
-#define PHYS_SDRAM_2 CSD1_BASE_ADDR
-#define PHYS_SDRAM_2_SIZE (256 * 1024 * 1024)
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-#define CONFIG_BOARD_EARLY_INIT_F
-
-/* 166 MHz DDR RAM */
-#define CONFIG_SYS_DDR_CLKSEL 0
-#define CONFIG_SYS_CLKTL_CBCDR 0x19239100
-#define CONFIG_SYS_MAIN_PWR_ON
-
-#define CONFIG_SYS_NO_FLASH
-
-/*
- * Framebuffer and LCD
- */
-#define CONFIG_PREBOOT
-#define CONFIG_VIDEO
-#define CONFIG_VIDEO_IPUV3
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
-#define CONFIG_VIDEO_BMP_RLE8
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_CMD_BMP
-#define CONFIG_BMP_16BPP
-#define CONFIG_IPUV3_CLK 133000000
-
-#endif /* __CONFIG_H */
--
2.5.0.457.gab17608
More information about the U-Boot
mailing list