[U-Boot] [PATCH v2 12/26] tegra124: dts: Add host1x node to provide display information

Simon Glass sjg at chromium.org
Sun Feb 1 17:54:07 CET 2015


This peripheral is required to get the LCD display running. Add it to
tegra124 and also bring in the binding file from Linux 3.18

Signed-off-by: Simon Glass <sjg at chromium.org>
---

Changes in v2: None

 arch/arm/dts/tegra124.dtsi                         |  84 +++++
 .../gpu/nvidia,tegra20-host1x.txt                  | 372 +++++++++++++++++++++
 2 files changed, 456 insertions(+)
 create mode 100644 doc/device-tree-bindings/gpu/nvidia,tegra20-host1x.txt

diff --git a/arch/arm/dts/tegra124.dtsi b/arch/arm/dts/tegra124.dtsi
index 9fa141d..43b7f22 100644
--- a/arch/arm/dts/tegra124.dtsi
+++ b/arch/arm/dts/tegra124.dtsi
@@ -76,6 +76,85 @@
 		};
 	};
 
+	host1x at 50000000 {
+		compatible = "nvidia,tegra124-host1x", "simple-bus";
+		reg = <0x50000000 0x00034000>;
+		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, /* syncpt */
+			     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; /* general */
+		clocks = <&tegra_car TEGRA124_CLK_HOST1X>;
+		resets = <&tegra_car 28>;
+		reset-names = "host1x";
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		ranges = <0x54000000 0x54000000 0x01000000>;
+
+		dc at 54200000 {
+			compatible = "nvidia,tegra124-dc";
+			reg = <0x54200000 0x00040000>;
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&tegra_car TEGRA124_CLK_DISP1>,
+				 <&tegra_car TEGRA124_CLK_PLL_P>;
+			clock-names = "dc", "parent";
+			resets = <&tegra_car 27>;
+			reset-names = "dc";
+
+			nvidia,head = <0>;
+		};
+
+		dc at 54240000 {
+			compatible = "nvidia,tegra124-dc";
+			reg = <0x54240000 0x00040000>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&tegra_car TEGRA124_CLK_DISP2>,
+				 <&tegra_car TEGRA124_CLK_PLL_P>;
+			clock-names = "dc", "parent";
+			resets = <&tegra_car 26>;
+			reset-names = "dc";
+
+			nvidia,head = <1>;
+		};
+
+		hdmi at 54280000 {
+			compatible = "nvidia,tegra124-hdmi";
+			reg = <0x54280000 0x00040000>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&tegra_car TEGRA124_CLK_HDMI>,
+				 <&tegra_car TEGRA124_CLK_PLL_D2_OUT0>;
+			clock-names = "hdmi", "parent";
+			resets = <&tegra_car 51>;
+			reset-names = "hdmi";
+			status = "disabled";
+		};
+
+		sor at 54540000 {
+			compatible = "nvidia,tegra124-sor";
+			reg = <0x54540000 0x00040000>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&tegra_car TEGRA124_CLK_SOR0>,
+				 <&tegra_car TEGRA124_CLK_PLL_D_OUT0>,
+				 <&tegra_car TEGRA124_CLK_PLL_DP>,
+				 <&tegra_car TEGRA124_CLK_CLK_M>;
+			clock-names = "sor", "parent", "dp", "safe";
+			resets = <&tegra_car 182>;
+			reset-names = "sor";
+			status = "disabled";
+		};
+
+		dpaux: dpaux at 545c0000 {
+			compatible = "nvidia,tegra124-dpaux";
+			reg = <0x545c0000 0x00040000>;
+			interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&tegra_car TEGRA124_CLK_DPAUX>,
+				 <&tegra_car TEGRA124_CLK_PLL_DP>;
+			clock-names = "dpaux", "parent";
+			resets = <&tegra_car 181>;
+			reset-names = "dpaux";
+			status = "disabled";
+		};
+	};
+
 	gic: interrupt-controller at 50041000 {
 		compatible = "arm,cortex-a15-gic";
 		#interrupt-cells = <3>;
@@ -349,6 +428,11 @@
 		clocks = <&tegra_car 105>;
 	};
 
+	pmc at 7000e400 {
+		compatible = "nvidia,tegra124-pmc";
+		reg = <0x7000e400 0x400>;
+	};
+
 	padctl: padctl at 7009f000 {
 		compatible = "nvidia,tegra124-xusb-padctl";
 		reg = <0x7009f000 0x1000>;
diff --git a/doc/device-tree-bindings/gpu/nvidia,tegra20-host1x.txt b/doc/device-tree-bindings/gpu/nvidia,tegra20-host1x.txt
new file mode 100644
index 0000000..b48f4ef
--- /dev/null
+++ b/doc/device-tree-bindings/gpu/nvidia,tegra20-host1x.txt
@@ -0,0 +1,372 @@
+NVIDIA Tegra host1x
+
+Required properties:
+- compatible: "nvidia,tegra<chip>-host1x"
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The interrupt outputs from the controller.
+- #address-cells: The number of cells used to represent physical base addresses
+  in the host1x address space. Should be 1.
+- #size-cells: The number of cells used to represent the size of an address
+  range in the host1x address space. Should be 1.
+- ranges: The mapping of the host1x address space to the CPU address space.
+- clocks: Must contain one entry, for the module clock.
+  See ../clocks/clock-bindings.txt for details.
+- resets: Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+  - host1x
+
+The host1x top-level node defines a number of children, each representing one
+of the following host1x client modules:
+
+- mpe: video encoder
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-mpe"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain one entry, for the module clock.
+    See ../clocks/clock-bindings.txt for details.
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - mpe
+
+- vi: video input
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-vi"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain one entry, for the module clock.
+    See ../clocks/clock-bindings.txt for details.
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - vi
+
+- epp: encoder pre-processor
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-epp"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain one entry, for the module clock.
+    See ../clocks/clock-bindings.txt for details.
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - epp
+
+- isp: image signal processor
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-isp"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain one entry, for the module clock.
+    See ../clocks/clock-bindings.txt for details.
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - isp
+
+- gr2d: 2D graphics engine
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-gr2d"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain one entry, for the module clock.
+    See ../clocks/clock-bindings.txt for details.
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - 2d
+
+- gr3d: 3D graphics engine
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-gr3d"
+  - reg: Physical base address and length of the controller's registers.
+  - clocks: Must contain an entry for each entry in clock-names.
+    See ../clocks/clock-bindings.txt for details.
+  - clock-names: Must include the following entries:
+    (This property may be omitted if the only clock in the list is "3d")
+    - 3d
+      This MUST be the first entry.
+    - 3d2 (Only required on SoCs with two 3D clocks)
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - 3d
+    - 3d2 (Only required on SoCs with two 3D clocks)
+
+- dc: display controller
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-dc"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain an entry for each entry in clock-names.
+    See ../clocks/clock-bindings.txt for details.
+  - clock-names: Must include the following entries:
+    - dc
+      This MUST be the first entry.
+    - parent
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - dc
+  - nvidia,head: The number of the display controller head. This is used to
+    setup the various types of output to receive video data from the given
+    head.
+
+  Each display controller node has a child node, named "rgb", that represents
+  the RGB output associated with the controller. It can take the following
+  optional properties:
+  - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+  - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
+  - nvidia,edid: supplies a binary EDID blob
+  - nvidia,panel: phandle of a display panel
+
+- hdmi: High Definition Multimedia Interface
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-hdmi"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - hdmi-supply: supply for the +5V HDMI connector pin
+  - vdd-supply: regulator for supply voltage
+  - pll-supply: regulator for PLL
+  - clocks: Must contain an entry for each entry in clock-names.
+    See ../clocks/clock-bindings.txt for details.
+  - clock-names: Must include the following entries:
+    - hdmi
+      This MUST be the first entry.
+    - parent
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - hdmi
+
+  Optional properties:
+  - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+  - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
+  - nvidia,edid: supplies a binary EDID blob
+  - nvidia,panel: phandle of a display panel
+
+- tvo: TV encoder output
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-tvo"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain one entry, for the module clock.
+    See ../clocks/clock-bindings.txt for details.
+
+- dsi: display serial interface
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-dsi"
+  - reg: Physical base address and length of the controller's registers.
+  - clocks: Must contain an entry for each entry in clock-names.
+    See ../clocks/clock-bindings.txt for details.
+  - clock-names: Must include the following entries:
+    - dsi
+      This MUST be the first entry.
+    - lp
+    - parent
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - dsi
+  - avdd-dsi-supply: phandle of a supply that powers the DSI controller
+  - nvidia,mipi-calibrate: Should contain a phandle and a specifier specifying
+    which pads are used by this DSI output and need to be calibrated. See also
+    ../mipi/nvidia,tegra114-mipi.txt.
+
+  Optional properties:
+  - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+  - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
+  - nvidia,edid: supplies a binary EDID blob
+  - nvidia,panel: phandle of a display panel
+
+- sor: serial output resource
+
+  Required properties:
+  - compatible: "nvidia,tegra124-sor"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain an entry for each entry in clock-names.
+    See ../clocks/clock-bindings.txt for details.
+  - clock-names: Must include the following entries:
+    - sor: clock input for the SOR hardware
+    - parent: input for the pixel clock
+    - dp: reference clock for the SOR clock
+    - safe: safe reference for the SOR clock during power up
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - sor
+
+  Optional properties:
+  - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+  - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
+  - nvidia,edid: supplies a binary EDID blob
+  - nvidia,panel: phandle of a display panel
+
+  Optional properties when driving an eDP output:
+  - nvidia,dpaux: phandle to a DispayPort AUX interface
+
+- dpaux: DisplayPort AUX interface
+  - compatible: "nvidia,tegra124-dpaux"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain an entry for each entry in clock-names.
+    See ../clocks/clock-bindings.txt for details.
+  - clock-names: Must include the following entries:
+    - dpaux: clock input for the DPAUX hardware
+    - parent: reference clock
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - dpaux
+  - vdd-supply: phandle of a supply that powers the DisplayPort link
+
+Example:
+
+/ {
+	...
+
+	host1x {
+		compatible = "nvidia,tegra20-host1x", "simple-bus";
+		reg = <0x50000000 0x00024000>;
+		interrupts = <0 65 0x04   /* mpcore syncpt */
+			      0 67 0x04>; /* mpcore general */
+		clocks = <&tegra_car TEGRA20_CLK_HOST1X>;
+		resets = <&tegra_car 28>;
+		reset-names = "host1x";
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		ranges = <0x54000000 0x54000000 0x04000000>;
+
+		mpe {
+			compatible = "nvidia,tegra20-mpe";
+			reg = <0x54040000 0x00040000>;
+			interrupts = <0 68 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_MPE>;
+			resets = <&tegra_car 60>;
+			reset-names = "mpe";
+		};
+
+		vi {
+			compatible = "nvidia,tegra20-vi";
+			reg = <0x54080000 0x00040000>;
+			interrupts = <0 69 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_VI>;
+			resets = <&tegra_car 100>;
+			reset-names = "vi";
+		};
+
+		epp {
+			compatible = "nvidia,tegra20-epp";
+			reg = <0x540c0000 0x00040000>;
+			interrupts = <0 70 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_EPP>;
+			resets = <&tegra_car 19>;
+			reset-names = "epp";
+		};
+
+		isp {
+			compatible = "nvidia,tegra20-isp";
+			reg = <0x54100000 0x00040000>;
+			interrupts = <0 71 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_ISP>;
+			resets = <&tegra_car 23>;
+			reset-names = "isp";
+		};
+
+		gr2d {
+			compatible = "nvidia,tegra20-gr2d";
+			reg = <0x54140000 0x00040000>;
+			interrupts = <0 72 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_GR2D>;
+			resets = <&tegra_car 21>;
+			reset-names = "2d";
+		};
+
+		gr3d {
+			compatible = "nvidia,tegra20-gr3d";
+			reg = <0x54180000 0x00040000>;
+			clocks = <&tegra_car TEGRA20_CLK_GR3D>;
+			resets = <&tegra_car 24>;
+			reset-names = "3d";
+		};
+
+		dc at 54200000 {
+			compatible = "nvidia,tegra20-dc";
+			reg = <0x54200000 0x00040000>;
+			interrupts = <0 73 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_DISP1>,
+				 <&tegra_car TEGRA20_CLK_PLL_P>;
+			clock-names = "dc", "parent";
+			resets = <&tegra_car 27>;
+			reset-names = "dc";
+
+			rgb {
+				status = "disabled";
+			};
+		};
+
+		dc at 54240000 {
+			compatible = "nvidia,tegra20-dc";
+			reg = <0x54240000 0x00040000>;
+			interrupts = <0 74 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_DISP2>,
+				 <&tegra_car TEGRA20_CLK_PLL_P>;
+			clock-names = "dc", "parent";
+			resets = <&tegra_car 26>;
+			reset-names = "dc";
+
+			rgb {
+				status = "disabled";
+			};
+		};
+
+		hdmi {
+			compatible = "nvidia,tegra20-hdmi";
+			reg = <0x54280000 0x00040000>;
+			interrupts = <0 75 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_HDMI>,
+				 <&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
+			clock-names = "hdmi", "parent";
+			resets = <&tegra_car 51>;
+			reset-names = "hdmi";
+			status = "disabled";
+		};
+
+		tvo {
+			compatible = "nvidia,tegra20-tvo";
+			reg = <0x542c0000 0x00040000>;
+			interrupts = <0 76 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_TVO>;
+			status = "disabled";
+		};
+
+		dsi {
+			compatible = "nvidia,tegra20-dsi";
+			reg = <0x54300000 0x00040000>;
+			clocks = <&tegra_car TEGRA20_CLK_DSI>,
+				 <&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
+			clock-names = "dsi", "parent";
+			resets = <&tegra_car 48>;
+			reset-names = "dsi";
+			status = "disabled";
+		};
+	};
+
+	...
+};
-- 
2.2.0.rc0.207.ga3a616c



More information about the U-Boot mailing list