[U-Boot] [PATCH 6/6] imx:mx6sxsabresd board spl support
Nikolay Dimitrov
picmaster at mail.bg
Mon Feb 2 11:24:10 CET 2015
Hi Peng,
On 01/19/2015 10:29 AM, Peng Fan wrote:
> Hi Stefano,
>
> On 1/19/2015 4:18 PM, Stefano Babic wrote:
>> Hi Peng,
>>
>> series looks ok to me - just a small question:
>>
>> On 30/12/2014 10:24, Peng Fan wrote:
>>> Add board level spl support for mx6sxsabresd board.
>>>
>>> Signed-off-by: Peng Fan <Peng.Fan at freescale.com>
>>> ---
>>> board/freescale/mx6sxsabresd/MAINTAINERS | 1 +
>>> board/freescale/mx6sxsabresd/mx6sxsabresd.c | 168
>>> ++++++++++++++++++++++++++++
>>> 2 files changed, 169 insertions(+)
>>>
>>> diff --git a/board/freescale/mx6sxsabresd/MAINTAINERS
>>> b/board/freescale/mx6sxsabresd/MAINTAINERS
>>> index f52f300..c0f5d9c 100644
>>> --- a/board/freescale/mx6sxsabresd/MAINTAINERS
>>> +++ b/board/freescale/mx6sxsabresd/MAINTAINERS
>>> @@ -4,3 +4,4 @@ S: Maintained
>>> F: board/freescale/mx6sxsabresd/
>>> F: include/configs/mx6sxsabresd.h
>>> F: configs/mx6sxsabresd_defconfig
>>> +F: configs/mx6sxsabresd_spl_defconfig
>>> diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c
>>> b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
>>> index fd8bc72..74f6d40 100644
>>> --- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c
>>> +++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
>>> @@ -326,6 +326,7 @@ int board_mmc_getcd(struct mmc *mmc)
>>> int board_mmc_init(bd_t *bis)
>>> {
>>> +#ifndef CONFIG_SPL_BUILD
>>> int i, ret;
>>> /*
>>> @@ -369,6 +370,47 @@ int board_mmc_init(bd_t *bis)
>>> }
>>> return 0;
>>> +#else
>>> + struct src *src_regs = (struct src *)SRC_BASE_ADDR;
>>> + u32 val;
>>> + u32 port;
>>> +
>>> + val = readl(&src_regs->sbmr1);
>>> +
>>> + if ((val & 0xc0) != 0x40) {
>>> + printf("Not boot from USDHC!\n");
>>> + return -EINVAL;
>>> + }
>>> +
>>> + port = (val >> 11) & 0x3;
>>> + printf("port %d\n", port);
>>> + switch (port) {
>>> + case 1:
>>> + imx_iomux_v3_setup_multiple_pads(
>>> + usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
>>> + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
>>> + usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
>>> + break;
>>> + case 2:
>>> + imx_iomux_v3_setup_multiple_pads(
>>> + usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
>>> + gpio_direction_input(USDHC3_CD_GPIO);
>>> + gpio_direction_output(USDHC3_PWR_GPIO, 1);
>>> + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
>>> + usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
>>> + break;
>>> + case 3:
>>> + imx_iomux_v3_setup_multiple_pads(
>>> + usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
>>> + gpio_direction_input(USDHC4_CD_GPIO);
>>> + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
>>> + usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
>>> + break;
>>> + }
>>> +
>>> + gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
>>> + return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
>>> +#endif
>>> }
>>> int board_init(void)
>>> @@ -394,3 +436,129 @@ int checkboard(void)
>>> return 0;
>>> }
>>> +
>>> +#ifdef CONFIG_SPL_BUILD
>>> +#include <libfdt.h>
>>> +#include <spl.h>
>>> +#include <asm/arch/mx6-ddr.h>
>>> +
>>> +const struct mx6sx_iomux_ddr_regs mx6_ddr_ioregs = {
>>> + .dram_dqm0 = 0x00000028,
>>> + .dram_dqm1 = 0x00000028,
>>> + .dram_dqm2 = 0x00000028,
>>> + .dram_dqm3 = 0x00000028,
>>> + .dram_ras = 0x00000020,
>>> + .dram_cas = 0x00000020,
>>> + .dram_odt0 = 0x00000020,
>>> + .dram_odt1 = 0x00000020,
>>> + .dram_sdba2 = 0x00000000,
>>> + .dram_sdcke0 = 0x00003000,
>>> + .dram_sdcke1 = 0x00003000,
>>> + .dram_sdclk_0 = 0x00000030,
>>> + .dram_sdqs0 = 0x00000028,
>>> + .dram_sdqs1 = 0x00000028,
>>> + .dram_sdqs2 = 0x00000028,
>>> + .dram_sdqs3 = 0x00000028,
>>> + .dram_reset = 0x00000020,
>>> +};
>>> +
>>> +const struct mx6sx_iomux_grp_regs mx6_grp_ioregs = {
>>> + .grp_addds = 0x00000020,
>>> + .grp_ddrmode_ctl = 0x00020000,
>>> + .grp_ddrpke = 0x00000000,
>>> + .grp_ddrmode = 0x00020000,
>>> + .grp_b0ds = 0x00000028,
>>> + .grp_b1ds = 0x00000028,
>>> + .grp_ctlds = 0x00000020,
>>> + .grp_ddr_type = 0x000c0000,
>>> + .grp_b2ds = 0x00000028,
>>> + .grp_b3ds = 0x00000028,
>>> +};
>>> +
>>> +const struct mx6_mmdc_calibration mx6_mmcd_calib = {
>>> + .p0_mpwldectrl0 = 0x00290025,
>>> + .p0_mpwldectrl1 = 0x00220022,
>>> + .p0_mpdgctrl0 = 0x41480144,
>>> + .p0_mpdgctrl1 = 0x01340130,
>>> + .p0_mprddlctl = 0x3C3E4244,
>>> + .p0_mpwrdlctl = 0x34363638,
>>> +};
>>> +
>>> +static struct mx6_ddr3_cfg mem_ddr = {
>>> + .mem_speed = 1600,
>>> + .density = 4,
>>> + .width = 32,
>>> + .banks = 8,
>>> + .rowaddr = 15,
>>> + .coladdr = 10,
>>> + .pagesz = 2,
>>> + .trcd = 1375,
>>> + .trcmin = 4875,
>>> + .trasmin = 3500,
>>> +};
>>> +
>>> +static void ccgr_init(void)
>>> +{
>>> + struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
>>> +
>>> + writel(0xFFFFFFFF, &ccm->CCGR0);
>>> + writel(0xFFFFFFFF, &ccm->CCGR1);
>>> + writel(0xFFFFFFFF, &ccm->CCGR2);
>>> + writel(0xFFFFFFFF, &ccm->CCGR3);
>>> + writel(0xFFFFFFFF, &ccm->CCGR4);
>>> + writel(0xFFFFFFFF, &ccm->CCGR5);
>>> + writel(0xFFFFFFFF, &ccm->CCGR6);
>>> + writel(0xFFFFFFFF, &ccm->CCGR7);
>>> +}
>>> +
>> Is it ok to enable all clocks ? This is quite uncommon in U-Boot and it
>> can raise some issues when Linux is booted because it assumes that
>> clocks are turned off. Anyway, this is only a question: if this is ok
>> for you (I do not test on this board), it is not an issue.
>
> In imximage.cfg DCD, all clocks is opened, so I add that in the spl to
> enable all clocks. This piece code is just the same thing in the DCD
> clock part.
> I have tested this patch set on mx6sxsabresd revb board and linux can
> boot ok.
Just FYI - when all the clocks are enabled, the imx6 can get
uncomfortably hot. I'm not sure how it's with the imx6sx, but I tried
in the past to enable all clocks on imx6d and it was not my best idea.
If this code will be running on the SabreSD development boards, your
users can spend quite a bit of time hacking around in the U-Boot
environment - editing env-vars, scripts, trying to guess boot args and
what-not, but at the same time the CPU will be running at full steam.
>
>>> +static void spl_dram_init(void)
>>> +{
>>> + struct mx6_ddr_sysinfo sysinfo = {
>>> + .dsize = mem_ddr.width/32,
>>> + .cs_density = 24,
>>> + .ncs = 1,
>>> + .cs1_mirror = 0,
>>> + .rtt_wr = 2,
>>> + .rtt_nom = 2, /* RTT_Nom = RZQ/2 */
>>> + .walat = 1, /* Write additional latency */
>>> + .ralat = 5, /* Read additional latency */
>>> + .mif3_mode = 3, /* Command prediction working mode */
>>> + .bi_on = 1, /* Bank interleaving enabled */
>>> + .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
>>> + .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
>>> + };
>>> +
>>> + mx6sx_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
>>> + mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
>>> +}
>>> +
>>> +void board_init_f(ulong dummy)
>>> +{
>>> + /* setup AIPS and disable watchdog */
>>> + arch_cpu_init();
>>> +
>>> + ccgr_init();
>>> +
>>> + /* iomux and setup of i2c */
>>> + board_early_init_f();
>>> +
>>> + /* setup GP timer */
>>> + timer_init();
>>> +
>>> + /* UART clocks enabled and gd valid - init serial console */
>>> + preloader_console_init();
>>> +
>>> + /* DDR initialization */
>>> + spl_dram_init();
>>> +
>>> + /* Clear the BSS. */
>>> + memset(__bss_start, 0, __bss_end - __bss_start);
>>> +
>>> + /* load/boot image from boot device */
>>> + board_init_r(NULL, 0);
>>> +}
>>> +
>>> +void reset_cpu(ulong addr)
>>> +{
>>> +}
>>> +#endif
>>>
>> Best regards,
>> Stefano Babic
>>
> Regards,
> Peng.
Kind regards,
Nikolay
More information about the U-Boot
mailing list