[U-Boot] [PATCH 4/4] imx: mx6sxsabreauto: Add support for mx6sx SABREAUTO board
Peng Fan
B51431 at freescale.com
Wed Feb 11 14:21:19 CET 2015
Hi,
On 2/11/2015 5:43 PM, Li Ye-B37916 wrote:
> Hi,
>
> On 2/10/2015 6:51 PM, Stefano Babic wrote:
>> Hi,
>>
>> On 12/01/2015 09:46, Ye.Li wrote:
>>> Initial version for mx6sx SABREAUTO board support with features:
>>> PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander.
>>>
>>> Signed-off-by: Ye.Li <B37916 at freescale.com>
>>> ---
>>> arch/arm/Kconfig | 5 +
>>> board/freescale/mx6sxsabreauto/Kconfig | 15 +
>>> board/freescale/mx6sxsabreauto/MAINTAINERS | 6 +
>>> board/freescale/mx6sxsabreauto/Makefile | 6 +
>>> board/freescale/mx6sxsabreauto/imximage.cfg | 136 ++++++
>>> board/freescale/mx6sxsabreauto/mx6sxsabreauto.c | 498 +++++++++++++++++++++++
>>> configs/mx6sxsabreauto_defconfig | 3 +
>>> include/configs/mx6sxsabreauto.h | 275 +++++++++++++
>>> 8 files changed, 944 insertions(+), 0 deletions(-)
>>> create mode 100644 board/freescale/mx6sxsabreauto/Kconfig
>>> create mode 100644 board/freescale/mx6sxsabreauto/MAINTAINERS
>>> create mode 100644 board/freescale/mx6sxsabreauto/Makefile
>>> create mode 100644 board/freescale/mx6sxsabreauto/imximage.cfg
>>> create mode 100644 board/freescale/mx6sxsabreauto/mx6sxsabreauto.c
>>> create mode 100644 configs/mx6sxsabreauto_defconfig
>>> create mode 100644 include/configs/mx6sxsabreauto.h
>>>
>>> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
>>> index 5eb1d03..9c54914 100644
>>> --- a/arch/arm/Kconfig
>>> +++ b/arch/arm/Kconfig
>>> @@ -638,6 +638,10 @@ config TARGET_MX6SXSABRESD
>>> bool "Support mx6sxsabresd"
>>> select CPU_V7
>>>
>>> +config TARGET_MX6SXSABREAUTO
>>> + bool "Support mx6sxsabreauto"
>>> + select CPU_V7
>>> +
>>> config TARGET_GW_VENTANA
>>> bool "Support gw_ventana"
>>> select CPU_V7
>>> @@ -916,6 +920,7 @@ source "board/freescale/mx6qsabreauto/Kconfig"
>>> source "board/freescale/mx6sabresd/Kconfig"
>>> source "board/freescale/mx6slevk/Kconfig"
>>> source "board/freescale/mx6sxsabresd/Kconfig"
>>> +source "board/freescale/mx6sxsabreauto/Kconfig"
>>> source "board/freescale/vf610twr/Kconfig"
>>> source "board/gateworks/gw_ventana/Kconfig"
>>> source "board/genesi/mx51_efikamx/Kconfig"
>>> diff --git a/board/freescale/mx6sxsabreauto/Kconfig b/board/freescale/mx6sxsabreauto/Kconfig
>>> new file mode 100644
>>> index 0000000..b0f5167
>>> --- /dev/null
>>> +++ b/board/freescale/mx6sxsabreauto/Kconfig
>>> @@ -0,0 +1,15 @@
>>> +if TARGET_MX6SXSABREAUTO
>>> +
>>> +config SYS_BOARD
>>> + default "mx6sxsabreauto"
>>> +
>>> +config SYS_VENDOR
>>> + default "freescale"
>>> +
>>> +config SYS_SOC
>>> + default "mx6"
>>> +
>>> +config SYS_CONFIG_NAME
>>> + default "mx6sxsabreauto"
>>> +
>>> +endif
>>> diff --git a/board/freescale/mx6sxsabreauto/MAINTAINERS b/board/freescale/mx6sxsabreauto/MAINTAINERS
>>> new file mode 100644
>>> index 0000000..dd3ae41
>>> --- /dev/null
>>> +++ b/board/freescale/mx6sxsabreauto/MAINTAINERS
>>> @@ -0,0 +1,6 @@
>>> +MX6SXSABREAUTO BOARD
>>> +M: Ye Li <Ye.Li at freescale.com>
>>> +S: Maintained
>>> +F: board/freescale/mx6sxsabreauto/
>>> +F: include/configs/mx6sxsabreauto.h
>>> +F: configs/mx6sxsabreauto_defconfig
>>> diff --git a/board/freescale/mx6sxsabreauto/Makefile b/board/freescale/mx6sxsabreauto/Makefile
>>> new file mode 100644
>>> index 0000000..f0cd1ce
>>> --- /dev/null
>>> +++ b/board/freescale/mx6sxsabreauto/Makefile
>>> @@ -0,0 +1,6 @@
>>> +# (C) Copyright 2014 Freescale Semiconductor, Inc.
>>> +#
>>> +# SPDX-License-Identifier: GPL-2.0+
>>> +#
>>> +
>>> +obj-y := mx6sxsabreauto.o
>>> diff --git a/board/freescale/mx6sxsabreauto/imximage.cfg b/board/freescale/mx6sxsabreauto/imximage.cfg
>>> new file mode 100644
>>> index 0000000..529e555
>>> --- /dev/null
>>> +++ b/board/freescale/mx6sxsabreauto/imximage.cfg
>>> @@ -0,0 +1,136 @@
>>> +/*
>>> + * Copyright (C) 2014 Freescale Semiconductor, Inc.
>>> + *
>>> + * SPDX-License-Identifier: GPL-2.0+
>>> + */
>>> +
>>> +#define __ASSEMBLY__
>>> +#include <config.h>
>>> +
>>> +/* image version */
>>> +
>>> +IMAGE_VERSION 2
>>> +
>>> +/*
>>> + * Boot Device : one of
>>> + * spi/sd/nand/onenand, qspi/nor
>>> + */
>>> +
>>> +BOOT_FROM sd
>>> +
>>> +/*
>>> + * Device Configuration Data (DCD)
>>> + *
>>> + * Each entry must have the format:
>>> + * Addr-type Address Value
>>> + *
>>> + * where:
>>> + * Addr-type register length (1,2 or 4 bytes)
>>> + * Address absolute address of the register
>>> + * value value to be stored in the register
>>> + */
>>> +
>>> +/* Enable all clocks */
>>> +DATA 4 0x020c4068 0xffffffff
>>> +DATA 4 0x020c406c 0xffffffff
>>> +DATA 4 0x020c4070 0xffffffff
>>> +DATA 4 0x020c4074 0xffffffff
>>> +DATA 4 0x020c4078 0xffffffff
>>> +DATA 4 0x020c407c 0xffffffff
>>> +DATA 4 0x020c4080 0xffffffff
>>> +DATA 4 0x020c4084 0xffffffff
>>> +
>> I will not block the patch for this: you are the maintainer and you can
>> test and check if this ok.
>>
>> I would only to point to the discussion with Peng regarding the same
>> issue for the mx6sxsabresd. Peng confirmed that he would send a
>> following patch for enabling only the clocks are needed. Mybe you can
>> synchronize wit him.
>>
> Ungating all clocks won't have functional problem, but consume more power at booting. For mx6 platforms,
> we won't change it any more, but on following mx7, we will use a new function to initialize needed clocks.
>
>>> +/* IOMUX - DDR IO Type */
>>> +DATA 4 0x020e0618 0x000c0000
>>> +DATA 4 0x020e05fc 0x00000000
>>> +
>>> +/* Clock */
>>> +DATA 4 0x020e032c 0x00000030
>>> +
>>> +/* Address */
>>> +DATA 4 0x020e0300 0x00000030
>>> +DATA 4 0x020e02fc 0x00000030
>>> +DATA 4 0x020e05f4 0x00000030
>>> +
>>> +/* Control */
>>> +DATA 4 0x020e0340 0x00000030
>>> +
>>> +DATA 4 0x020e0320 0x00000000
>>> +DATA 4 0x020e0310 0x00000030
>>> +DATA 4 0x020e0314 0x00000030
>>> +DATA 4 0x020e0614 0x00000030
>>> +
>>> +/* Data Strobe */
>>> +DATA 4 0x020e05f8 0x00020000
>>> +DATA 4 0x020e0330 0x00000030
>>> +DATA 4 0x020e0334 0x00000030
>>> +DATA 4 0x020e0338 0x00000030
>>> +DATA 4 0x020e033c 0x00000030
>>> +
>>> +/* Data */
>>> +DATA 4 0x020e0608 0x00020000
>>> +DATA 4 0x020e060c 0x00000030
>>> +DATA 4 0x020e0610 0x00000030
>>> +DATA 4 0x020e061c 0x00000030
>>> +DATA 4 0x020e0620 0x00000030
>>> +DATA 4 0x020e02ec 0x00000030
>>> +DATA 4 0x020e02f0 0x00000030
>>> +DATA 4 0x020e02f4 0x00000030
>>> +DATA 4 0x020e02f8 0x00000030
>>> +
>>> +/* Calibrations - ZQ */
>>> +DATA 4 0x021b0800 0xa1390003
>>> +
>>> +/* Write leveling */
>>> +DATA 4 0x021b080c 0x002C003D
>>> +DATA 4 0x021b0810 0x00110046
>>> +
>>> +/* DQS Read Gate */
>>> +DATA 4 0x021b083c 0x4160016C
>>> +DATA 4 0x021b0840 0x013C016C
>>> +
>>> +/* Read/Write Delay */
>>> +DATA 4 0x021b0848 0x46424446
>>> +DATA 4 0x021b0850 0x3A3C3C3A
>>> +
>>> +DATA 4 0x021b08c0 0x2492244A
>>> +
>>> +/* read data bit delay */
>>> +DATA 4 0x021b081c 0x33333333
>>> +DATA 4 0x021b0820 0x33333333
>>> +DATA 4 0x021b0824 0x33333333
>>> +DATA 4 0x021b0828 0x33333333
>>> +
>>> +/* Complete calibration by forced measurement */
>>> +DATA 4 0x021b08b8 0x00000800
>>> +
>>> +/* MMDC init - DDR3, 64-bit mode, only MMDC0 is initiated */
>>> +DATA 4 0x021b0004 0x0002002d
>>> +DATA 4 0x021b0008 0x00333030
>>> +DATA 4 0x021b000c 0x676b52f3
>>> +DATA 4 0x021b0010 0xb66d8b63
>>> +DATA 4 0x021b0014 0x01ff00db
>>> +DATA 4 0x021b0018 0x00011740
>>> +DATA 4 0x021b001c 0x00008000
>>> +DATA 4 0x021b002c 0x000026d2
>>> +DATA 4 0x021b0030 0x006b1023
>>> +DATA 4 0x021b0040 0x0000007f
>>> +DATA 4 0x021b0000 0x85190000
>>> +
>>> +/* Initialize MT41K256M16HA-125 - MR2 */
>>> +DATA 4 0x021b001c 0x04008032
>>> +/* MR3 */
>>> +DATA 4 0x021b001c 0x00008033
>>> +/* MR1 */
>>> +DATA 4 0x021b001c 0x00068031
>>> +/* MR0 */
>>> +DATA 4 0x021b001c 0x05208030
>>> +/* DDR device ZQ calibration */
>>> +DATA 4 0x021b001c 0x04008040
>>> +
>>> +/* Final DDR setup, before operation start */
>>> +DATA 4 0x021b0020 0x00000800
>>> +DATA 4 0x021b0818 0x00022227
>>> +DATA 4 0x021b0004 0x0002556d
>>> +DATA 4 0x021b0404 0x00011006
>>> +DATA 4 0x021b001c 0x00000000
>> ok, I admit that diggering into the DCD table requires too much effort.
>> What about to move to SPL code ? I have expected that new i.MX6 boards
>> will be moved to support SPL, but it looks like that most patches still
>> stick with DCD tables. A couple of Freescale's boards were already
>> ported to SPL and merged. Have you considered to use SPL ? If yes, which
>> are the reason to not support it ?
>>
> I think the DCD script "imximage.cfg" is not conflict with SPL. Because for non-SPL case, this file is needed. They are not exclusive.
> At default Freescale release, we use DCD and plugin. But actually, DCD, SPL and plugin can exist with each others. This provides
> options for customer to choose.
>
> As a initial BSP version, we only support DCD here, neither SPL and Plugin. But we could consider to add in future.
>
>>> diff --git a/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c b/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c
>>> new file mode 100644
>>> index 0000000..a406a1d
>>> --- /dev/null
>>> +++ b/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c
>>> @@ -0,0 +1,498 @@
>>> +/*
>>> + * Copyright (C) 2014 Freescale Semiconductor, Inc.
>>> + *
>>> + * Author: Ye Li <Ye.Li at freescale.com>
>>> + *
>>> + * SPDX-License-Identifier: GPL-2.0+
>>> + */
>>> +
>>> +#include <asm/arch/clock.h>
>>> +#include <asm/arch/crm_regs.h>
>>> +#include <asm/arch/iomux.h>
>>> +#include <asm/arch/imx-regs.h>
>>> +#include <asm/arch/mx6-pins.h>
>>> +#include <asm/arch/sys_proto.h>
>>> +#include <asm/gpio.h>
>>> +#include <asm/imx-common/iomux-v3.h>
>>> +#include <asm/io.h>
>>> +#include <asm/imx-common/mxc_i2c.h>
>>> +#include <linux/sizes.h>
>>> +#include <common.h>
>>> +#include <fsl_esdhc.h>
>>> +#include <mmc.h>
>>> +#include <i2c.h>
>>> +#include <miiphy.h>
>>> +#include <netdev.h>
>>> +#include <power/pmic.h>
>>> +#include <power/pfuze100_pmic.h>
>>> +#include "../common/pfuze.h"
>>> +#include <usb.h>
>>> +#include <usb/ehci-fsl.h>
>>> +#include <pca953x.h>
>>> +
>>> +DECLARE_GLOBAL_DATA_PTR;
>>> +
>>> +#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
>>> + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
>>> + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
>>> +
>>> +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
>>> + PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
>>> + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
>>> +
>>> +#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
>>> + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
>>> + PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
>>> + PAD_CTL_ODE)
>>> +
>>> +#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
>>> + PAD_CTL_SPEED_HIGH | \
>>> + PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST)
>>> +
>>> +#define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \
>>> + PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST)
>>> +
>>> +#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
>>> + PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST)
>>> +
>>> +#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
>>> + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
>>> + PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
>>> + PAD_CTL_ODE)
>>> +
>>> +#define I2C_PMIC 1
>>> +
>>> +#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
>>> +#define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
>>> + PAD_CTL_SRE_FAST)
>>> +#define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)
>>> +
>>> +/*Define for building port exp gpio, pin starts from 0*/
>>> +#define PORTEXP_IO_NR(chip, pin) \
>>> + ((chip << 5) + pin)
>>> +
>>> +/*Get the chip addr from a ioexp gpio*/
>>> +#define PORTEXP_IO_TO_CHIP(gpio_nr) \
>>> + (gpio_nr >> 5)
>>> +
>>> +/*Get the pin number from a ioexp gpio*/
>>> +#define PORTEXP_IO_TO_PIN(gpio_nr) \
>>> + (gpio_nr & 0x1f)
>>> +
>>> +#define CPU_PER_RST_B PORTEXP_IO_NR(0x30, 4)
>>> +#define STEER_ENET PORTEXP_IO_NR(0x32, 2)
>>> +
>>> +static int port_exp_direction_output(unsigned gpio, int value)
>>> +{
>>> + int ret;
>>> +
>>> + i2c_set_bus_num(2);
>>> + ret = i2c_probe(PORTEXP_IO_TO_CHIP(gpio));
>> Is it required to call every time i2c_probe() ? Should be called only once ?
> The i2c_probe is needed only call once. Since it is a light weight encapsulation for using pca953x, I don't want
> to add more variables nor functions. I will remove the i2c_probe in next version, it is not necessary.
>
>>> + if (ret)
>>> + return ret;
>>> +
>>> + ret = pca953x_set_dir(PORTEXP_IO_TO_CHIP(gpio),
>>> + (1 << PORTEXP_IO_TO_PIN(gpio)),
>>> + (PCA953X_DIR_OUT << PORTEXP_IO_TO_PIN(gpio)));
>>> +
>>> + if (ret)
>>> + return ret;
>>> +
>>> + ret = pca953x_set_val(PORTEXP_IO_TO_CHIP(gpio),
>>> + (1 << PORTEXP_IO_TO_PIN(gpio)),
>>> + (value << PORTEXP_IO_TO_PIN(gpio)));
>>> +
>>> + if (ret)
>>> + return ret;
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +int dram_init(void)
>>> +{
>>> + gd->ram_size = PHYS_SDRAM_SIZE;
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static iomux_v3_cfg_t const uart1_pads[] = {
>>> + MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
>>> + MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
>>> +};
>>> +
>>> +static iomux_v3_cfg_t const usdhc3_pads[] = {
>>> + MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD3_DATA0__USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD3_DATA1__USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD3_DATA2__USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD3_DATA3__USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD3_DATA4__USDHC3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD3_DATA5__USDHC3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD3_DATA6__USDHC3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD3_DATA7__USDHC3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> +
>>> + /* CD pin */
>>> + MX6_PAD_USB_H_DATA__GPIO7_IO_10 | MUX_PAD_CTRL(NO_PAD_CTRL),
>>> +
>>> + /* RST_B, used for power reset cycle */
>>> + MX6_PAD_KEY_COL1__GPIO2_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL),
>>> +};
>>> +
>>> +static iomux_v3_cfg_t const usdhc4_pads[] = {
>>> + MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> + MX6_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>>> +
>>> + /* CD pin */
>>> + MX6_PAD_USB_H_STROBE__GPIO7_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL),
>>> +};
>>> +
>>> +static iomux_v3_cfg_t const fec2_pads[] = {
>>> + MX6_PAD_ENET1_MDC__ENET2_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>> + MX6_PAD_ENET1_MDIO__ENET2_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>> + MX6_PAD_RGMII2_RX_CTL__ENET2_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
>>> + MX6_PAD_RGMII2_RD0__ENET2_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
>>> + MX6_PAD_RGMII2_RD1__ENET2_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
>>> + MX6_PAD_RGMII2_RD2__ENET2_RX_DATA_2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
>>> + MX6_PAD_RGMII2_RD3__ENET2_RX_DATA_3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
>>> + MX6_PAD_RGMII2_RXC__ENET2_RX_CLK | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
>>> + MX6_PAD_RGMII2_TX_CTL__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>> + MX6_PAD_RGMII2_TD0__ENET2_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>> + MX6_PAD_RGMII2_TD1__ENET2_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>> + MX6_PAD_RGMII2_TD2__ENET2_TX_DATA_2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>> + MX6_PAD_RGMII2_TD3__ENET2_TX_DATA_3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>> + MX6_PAD_RGMII2_TXC__ENET2_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
>>> +};
>>> +
>>> +static void setup_iomux_uart(void)
>>> +{
>>> + imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
>>> +}
>>> +
>>> +static int setup_fec(void)
>>> +{
>>> + struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
>>> +
>>> + /* Use 125MHz anatop loopback REF_CLK1 for ENET2 */
>>> + clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK, 0);
>>> +
>>> + return enable_fec_anatop_clock(ENET_125MHZ);
>>> +}
>>> +
>>> +int board_eth_init(bd_t *bis)
>>> +{
>>> + int ret;
>>> +
>>> + imx_iomux_v3_setup_multiple_pads(fec2_pads, ARRAY_SIZE(fec2_pads));
>>> + setup_fec();
>>> +
>>> + ret = fecmxc_initialize_multi(bis, 1,
>>> + CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
>>> + if (ret)
>>> + printf("FEC%d MXC: %s:failed\n", 1, __func__);
>>> +
>>> + return ret;
>>> +}
>>> +
>>> +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
>>> +/* I2C2 for PMIC */
>>> +struct i2c_pads_info i2c_pad_info2 = {
>>> + .scl = {
>>> + .i2c_mode = MX6_PAD_GPIO1_IO02__I2C2_SCL | PC,
>>> + .gpio_mode = MX6_PAD_GPIO1_IO02__GPIO1_IO_2 | PC,
>>> + .gp = IMX_GPIO_NR(1, 2),
>>> + },
>>> + .sda = {
>>> + .i2c_mode = MX6_PAD_GPIO1_IO03__I2C2_SDA | PC,
>>> + .gpio_mode = MX6_PAD_GPIO1_IO03__GPIO1_IO_3 | PC,
>>> + .gp = IMX_GPIO_NR(1, 3),
>>> + },
>>> +};
>>> +
>>> +/* I2C3 for IO Expander */
>>> +struct i2c_pads_info i2c_pad_info3 = {
>>> + .scl = {
>>> + .i2c_mode = MX6_PAD_KEY_COL4__I2C3_SCL | PC,
>>> + .gpio_mode = MX6_PAD_KEY_COL4__GPIO2_IO_14 | PC,
>>> + .gp = IMX_GPIO_NR(2, 14),
>>> + },
>>> + .sda = {
>>> + .i2c_mode = MX6_PAD_KEY_ROW4__I2C3_SDA | PC,
>>> + .gpio_mode = MX6_PAD_KEY_ROW4__GPIO2_IO_19 | PC,
>>> + .gp = IMX_GPIO_NR(2, 19),
>>> + },
>>> +};
>>> +
>>> +int power_init_board(void)
>>> +{
>>> + struct pmic *p;
>>> +
>>> + p = pfuze_common_init(I2C_PMIC);
>>> + if (!p)
>>> + return -ENODEV;
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +#ifdef CONFIG_USB_EHCI_MX6
>>> +#define USB_OTHERREGS_OFFSET 0x800
>>> +#define UCTRL_PWR_POL (1 << 9)
>>> +
>>> +static iomux_v3_cfg_t const usb_otg_pads[] = {
>>> + /* OGT1 */
>>> + MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
>>> + MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
>>> + /* OTG2 */
>>> + MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)
>>> +};
>>> +
>>> +static void setup_usb(void)
>>> +{
>>> + imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
>>> + ARRAY_SIZE(usb_otg_pads));
>>> +}
>>> +
>>> +int board_usb_phy_mode(int port)
>>> +{
>>> + if (port == 1)
>>> + return USB_INIT_HOST;
>>> + else
>>> + return usb_phy_mode(port);
>>> +}
>>> +
>>> +int board_ehci_hcd_init(int port)
>>> +{
>>> + u32 *usbnc_usb_ctrl;
>>> +
>>> + if (port > 1)
>>> + return -EINVAL;
>>> +
>>> + usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
>>> + port * 4);
>>> +
>>> + /* Set Power polarity */
>>> + setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
>>> +
>>> + return 0;
>>> +}
>>> +#endif
>>> +
>>> +int board_phy_config(struct phy_device *phydev)
>>> +{
>>> + /*
>>> + * Enable 1.8V(SEL_1P5_1P8_POS_REG) on
>>> + * Phy control debug reg 0
>>> + */
>>> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
>>> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
>>> +
>>> + /* rgmii tx clock delay enable */
>>> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
>>> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
>>> +
>>> + if (phydev->drv->config)
>>> + phydev->drv->config(phydev);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +int board_early_init_f(void)
>>> +{
>>> + setup_iomux_uart();
>>> +
>>> +#ifdef CONFIG_USB_EHCI_MX6
>>> + setup_usb();
>> Why USB here and not in board_init ? It is not a problem because you set
>> only the pinmux, but if setup_usb() will be changed in future, it is
>> easy to forget that it is called before relocation.
> This is copy from mx6sxsabresd. Will move it to board_init.
The usb support patch for mx6sxsabresd which was applied is this one,
http://lists.denx.de/pipermail/u-boot/2014-November/194870.html.
setup_usb in this patch is called in board_init, but I have no idea why
it went into board_early_init_f.
>
>>> +#endif
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static struct fsl_esdhc_cfg usdhc_cfg[3] = {
>>> + {USDHC3_BASE_ADDR},
>>> + {USDHC4_BASE_ADDR},
>>> +};
>>> +
>>> +#define USDHC3_CD_GPIO IMX_GPIO_NR(7, 10)
>>> +#define USDHC3_RST_GPIO IMX_GPIO_NR(2, 11)
>>> +#define USDHC4_CD_GPIO IMX_GPIO_NR(7, 11)
>>> +
>>> +int board_mmc_getcd(struct mmc *mmc)
>>> +{
>>> + struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
>>> + int ret = 0;
>>> +
>>> + switch (cfg->esdhc_base) {
>>> + case USDHC3_BASE_ADDR:
>>> + ret = !gpio_get_value(USDHC3_CD_GPIO);
>>> + break;
>>> + case USDHC4_BASE_ADDR:
>>> + ret = !gpio_get_value(USDHC4_CD_GPIO);
>>> + break;
>>> + }
>>> +
>>> + return ret;
>>> +}
>>> +
>>> +int board_mmc_init(bd_t *bis)
>>> +{
>>> + int i, ret;
>>> +
>>> + /*
>>> + * According to the board_mmc_init() the following map is done:
>>> + * (U-boot device node) (Physical Port)
>>> + * mmc0 USDHC3
>>> + * mmc1 USDHC4
>>> + */
>>> + for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
>>> + switch (i) {
>>> + case 0:
>>> + imx_iomux_v3_setup_multiple_pads(
>>> + usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
>>> + gpio_direction_input(USDHC3_CD_GPIO);
>>> +
>>> + /* This starts a power cycle for UHS-I. Need to set steer to B0 to A*/
>>> + gpio_direction_output(USDHC3_RST_GPIO, 0);
>>> + udelay(1000); /* need 1ms at least */
>>> + gpio_direction_output(USDHC3_RST_GPIO, 1);
>>> +
>>> + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
>>> + break;
>>> + case 1:
>>> + imx_iomux_v3_setup_multiple_pads(
>>> + usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
>>> + gpio_direction_input(USDHC4_CD_GPIO);
>>> + usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
>>> + break;
>>> + default:
>>> + printf("Warning: you configured more USDHC controllers"
>>> + "(%d) than supported by the board\n", i + 1);
>>> + return -EINVAL;
>>> + }
>>> +
>>> + ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
>>> + if (ret) {
>>> + printf("Warning: failed to initialize mmc dev %d\n", i);
>> There was a clean-up patchset by Fabio - fsl_esdhc_initialize() prints
>> already a warning, you do not need a second one here.
> Ok, will remove it.
>
>>> + return ret;
>>> + }
>>> + }
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +#ifdef CONFIG_FSL_QSPI
>>> +
>>> +#define QSPI_PAD_CTRL1 \
>>> + (PAD_CTL_SRE_FAST | PAD_CTL_SPEED_HIGH | \
>>> + PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_40ohm)
>>> +
>>> +static iomux_v3_cfg_t const quadspi_pads[] = {
>>> + MX6_PAD_QSPI1A_SS0_B__QSPI1_A_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
>>> + MX6_PAD_QSPI1A_SCLK__QSPI1_A_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
>>> + MX6_PAD_QSPI1A_DATA0__QSPI1_A_DATA_0 | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
>>> + MX6_PAD_QSPI1A_DATA1__QSPI1_A_DATA_1 | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
>>> + MX6_PAD_QSPI1A_DATA2__QSPI1_A_DATA_2 | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
>>> + MX6_PAD_QSPI1A_DATA3__QSPI1_A_DATA_3 | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
>>> + MX6_PAD_QSPI1B_SS0_B__QSPI1_B_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
>>> + MX6_PAD_QSPI1B_SCLK__QSPI1_B_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
>>> + MX6_PAD_QSPI1B_DATA0__QSPI1_B_DATA_0 | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
>>> + MX6_PAD_QSPI1B_DATA1__QSPI1_B_DATA_1 | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
>>> + MX6_PAD_QSPI1B_DATA2__QSPI1_B_DATA_2 | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
>>> + MX6_PAD_QSPI1B_DATA3__QSPI1_B_DATA_3 | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
>>> +};
>>> +
>>> +int board_qspi_init(void)
>>> +{
>>> + /* Set the iomux */
>>> + imx_iomux_v3_setup_multiple_pads(quadspi_pads,
>>> + ARRAY_SIZE(quadspi_pads));
>>> +
>>> + /* Set the clock */
>>> + enable_qspi_clk(0);
>>> +
>>> + return 0;
>>> +}
>>> +#endif
>>> +
>>> +#ifdef CONFIG_NAND_MXS
>>> +iomux_v3_cfg_t gpmi_pads[] = {
>>> + MX6_PAD_NAND_CLE__RAWNAND_CLE | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
>>> + MX6_PAD_NAND_ALE__RAWNAND_ALE | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
>>> + MX6_PAD_NAND_WP_B__RAWNAND_WP_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
>>> + MX6_PAD_NAND_READY_B__RAWNAND_READY_B | MUX_PAD_CTRL(GPMI_PAD_CTRL0),
>>> + MX6_PAD_NAND_CE0_B__RAWNAND_CE0_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
>>> + MX6_PAD_NAND_RE_B__RAWNAND_RE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
>>> + MX6_PAD_NAND_WE_B__RAWNAND_WE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
>>> + MX6_PAD_NAND_DATA00__RAWNAND_DATA00 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
>>> + MX6_PAD_NAND_DATA01__RAWNAND_DATA01 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
>>> + MX6_PAD_NAND_DATA02__RAWNAND_DATA02 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
>>> + MX6_PAD_NAND_DATA03__RAWNAND_DATA03 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
>>> + MX6_PAD_NAND_DATA04__RAWNAND_DATA04 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
>>> + MX6_PAD_NAND_DATA05__RAWNAND_DATA05 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
>>> + MX6_PAD_NAND_DATA06__RAWNAND_DATA06 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
>>> + MX6_PAD_NAND_DATA07__RAWNAND_DATA07 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
>>> +};
>>> +
>>> +static void setup_gpmi_nand(void)
>>> +{
>>> + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
>>> +
>>> + /* config gpmi nand iomux */
>>> + imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads));
>>> +
>>> + setup_gpmi_io_clk((MXC_CCM_CS2CDR_QSPI2_CLK_PODF(0) |
>>> + MXC_CCM_CS2CDR_QSPI2_CLK_PRED(3) |
>>> + MXC_CCM_CS2CDR_QSPI2_CLK_SEL(3)));
>>> +
>>> + /* enable apbh clock gating */
>>> + setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
>>> +}
>>> +#endif
>>> +
>>> +int board_init(void)
>>> +{
>>> + /* Address of boot parameters */
>>> + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
>>> +
>>> +#ifdef CONFIG_SYS_I2C_MXC
>>> + setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
>>> + setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3);
>>> +#endif
>>> +
>>> + /* Reset CPU_PER_RST_B signal for enet phy and PCIE */
>>> + port_exp_direction_output(CPU_PER_RST_B, 0);
>>> + udelay(500);
>>> + port_exp_direction_output(CPU_PER_RST_B, 1);
>>> +
>>> + /* Set steering signal to L for selecting B0 */
>>> + port_exp_direction_output(STEER_ENET, 0);
>>> +
>>> +#ifdef CONFIG_FSL_QSPI
>>> + board_qspi_init();
>>> +#endif
>>> +
>>> +#ifdef CONFIG_NAND_MXS
>>> + setup_gpmi_nand();
>>> +#endif
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +int board_late_init(void)
>>> +{
>>> + return 0;
>>> +}
>> Drop it if you do not use it.
> Accept.
>
>>> +
>>> +int checkboard(void)
>>> +{
>>> + puts("Board: MX6SX SABRE AUTO\n");
>>> +
>>> + return 0;
>>> +}
>>> diff --git a/configs/mx6sxsabreauto_defconfig b/configs/mx6sxsabreauto_defconfig
>>> new file mode 100644
>>> index 0000000..ca5ff27
>>> --- /dev/null
>>> +++ b/configs/mx6sxsabreauto_defconfig
>>> @@ -0,0 +1,3 @@
>>> +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6sxsabreauto/imximage.cfg,MX6SX"
>>> +CONFIG_ARM=y
>>> +CONFIG_TARGET_MX6SXSABREAUTO=y
>>> diff --git a/include/configs/mx6sxsabreauto.h b/include/configs/mx6sxsabreauto.h
>>> new file mode 100644
>>> index 0000000..082abaf
>>> --- /dev/null
>>> +++ b/include/configs/mx6sxsabreauto.h
>>> @@ -0,0 +1,275 @@
>>> +/*
>>> + * Copyright 2014 Freescale Semiconductor, Inc.
>>> + *
>>> + * Configuration settings for the Freescale i.MX6SX Sabreauto board.
>>> + *
>>> + * SPDX-License-Identifier: GPL-2.0+
>>> + */
>>> +
>>> +
>>> +#ifndef __CONFIG_H
>>> +#define __CONFIG_H
>>> +
>>> +#include <asm/arch/imx-regs.h>
>>> +#include <linux/sizes.h>
>>> +#include "mx6_common.h"
>>> +
>>> +#define CONFIG_MX6
>>> +#define CONFIG_DISPLAY_CPUINFO
>>> +#define CONFIG_DISPLAY_BOARDINFO
>>> +
>>> +#define CONFIG_CMDLINE_TAG
>>> +#define CONFIG_SETUP_MEMORY_TAGS
>>> +#define CONFIG_INITRD_TAG
>>> +#define CONFIG_REVISION_TAG
>>> +#define CONFIG_SYS_GENERIC_BOARD
>>> +
>>> +/* Size of malloc() pool */
>>> +#define CONFIG_SYS_MALLOC_LEN (3 * SZ_1M)
>>> +
>>> +#define CONFIG_BOARD_EARLY_INIT_F
>>> +#define CONFIG_BOARD_LATE_INIT
>>> +#define CONFIG_MXC_GPIO
>>> +
>>> +#define CONFIG_MXC_UART
>>> +#define CONFIG_MXC_UART_BASE UART1_BASE
>>> +
>>> +/* allow to overwrite serial and ethaddr */
>>> +#define CONFIG_ENV_OVERWRITE
>>> +#define CONFIG_CONS_INDEX 1
>>> +#define CONFIG_BAUDRATE 115200
>>> +
>>> +/* Command definition */
>>> +#include <config_cmd_default.h>
>>> +
>>> +#undef CONFIG_CMD_IMLS
>>> +
>>> +#define CONFIG_BOOTDELAY 3
>>> +
>>> +#define CONFIG_LOADADDR 0x80800000
>>> +#define CONFIG_SYS_TEXT_BASE 0x87800000
>>> +
>>> +#define CONFIG_EXTRA_ENV_SETTINGS \
>>> + "script=boot.scr\0" \
>>> + "image=zImage\0" \
>>> + "console=ttymxc0\0" \
>>> + "fdt_high=0xffffffff\0" \
>>> + "initrd_high=0xffffffff\0" \
>>> + "fdt_file=imx6sx-sabreauto.dtb\0" \
>>> + "fdt_addr=0x88000000\0" \
>>> + "boot_fdt=try\0" \
>>> + "ip_dyn=yes\0" \
>>> + "mmcdev=0\0" \
>>> + "mmcpart=1\0" \
>>> + "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
>>> + "mmcargs=setenv bootargs console=${console},${baudrate} " \
>>> + "root=${mmcroot}\0" \
>>> + "loadbootscript=" \
>>> + "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
>>> + "bootscript=echo Running bootscript from mmc ...; " \
>>> + "source\0" \
>>> + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
>>> + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
>>> + "mmcboot=echo Booting from mmc ...; " \
>>> + "run mmcargs; " \
>>> + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
>>> + "if run loadfdt; then " \
>>> + "bootz ${loadaddr} - ${fdt_addr}; " \
>>> + "else " \
>>> + "if test ${boot_fdt} = try; then " \
>>> + "bootz; " \
>>> + "else " \
>>> + "echo WARN: Cannot load the DT; " \
>>> + "fi; " \
>>> + "fi; " \
>>> + "else " \
>>> + "bootz; " \
>>> + "fi;\0" \
>>> + "netargs=setenv bootargs console=${console},${baudrate} " \
>>> + "root=/dev/nfs " \
>>> + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
>>> + "netboot=echo Booting from net ...; " \
>>> + "run netargs; " \
>>> + "if test ${ip_dyn} = yes; then " \
>>> + "setenv get_cmd dhcp; " \
>>> + "else " \
>>> + "setenv get_cmd tftp; " \
>>> + "fi; " \
>>> + "${get_cmd} ${image}; " \
>>> + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
>>> + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
>>> + "bootz ${loadaddr} - ${fdt_addr}; " \
>>> + "else " \
>>> + "if test ${boot_fdt} = try; then " \
>>> + "bootz; " \
>>> + "else " \
>>> + "echo WARN: Cannot load the DT; " \
>>> + "fi; " \
>>> + "fi; " \
>>> + "else " \
>>> + "bootz; " \
>>> + "fi;\0"
>>> +
>>> +#define CONFIG_BOOTCOMMAND \
>>> + "mmc dev ${mmcdev};" \
>>> + "mmc dev ${mmcdev}; if mmc rescan; then " \
>>> + "if run loadbootscript; then " \
>>> + "run bootscript; " \
>>> + "else " \
>>> + "if run loadimage; then " \
>>> + "run mmcboot; " \
>>> + "else run netboot; " \
>>> + "fi; " \
>>> + "fi; " \
>>> + "else run netboot; fi"
>>> +
>>> +/* Miscellaneous configurable options */
>>> +#define CONFIG_SYS_LONGHELP
>>> +#define CONFIG_SYS_HUSH_PARSER
>>> +#define CONFIG_AUTO_COMPLETE
>>> +#define CONFIG_SYS_CBSIZE 1024
>>> +
>>> +/* Print Buffer Size */
>>> +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
>>> +#define CONFIG_SYS_MAXARGS 256
>>> +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
>>> +
>>> +#define CONFIG_SYS_MEMTEST_START 0x80000000
>>> +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x10000)
>>> +
>>> +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
>>> +
>>> +#define CONFIG_CMDLINE_EDITING
>>> +#define CONFIG_STACKSIZE SZ_128K
>>> +
>>> +/* Physical Memory Map */
>>> +#define CONFIG_NR_DRAM_BANKS 1
>>> +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
>>> +#define PHYS_SDRAM_SIZE SZ_2G
>>> +
>>> +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
>>> +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
>>> +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
>>> +
>>> +#define CONFIG_SYS_INIT_SP_OFFSET \
>>> + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
>>> +#define CONFIG_SYS_INIT_SP_ADDR \
>>> + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
>>> +
>>> +/* MMC Configuration */
>>> +#define CONFIG_FSL_ESDHC
>>> +#define CONFIG_FSL_USDHC
>>> +#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC3_BASE_ADDR
>>> +
>>> +#define CONFIG_MMC
>>> +#define CONFIG_CMD_MMC
>>> +#define CONFIG_GENERIC_MMC
>>> +#define CONFIG_BOUNCE_BUFFER
>>> +#define CONFIG_CMD_EXT2
>>> +#define CONFIG_CMD_FAT
>>> +#define CONFIG_DOS_PARTITION
>>> +
>>> +/* I2C Configs */
>>> +#define CONFIG_CMD_I2C
>>> +#define CONFIG_SYS_I2C
>>> +#define CONFIG_SYS_I2C_MXC
>>> +#define CONFIG_SYS_I2C_SPEED 100000
>>> +
>>> +/* PMIC */
>>> +#define CONFIG_POWER
>>> +#define CONFIG_POWER_I2C
>>> +#define CONFIG_POWER_PFUZE100
>>> +#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
>>> +
>>> +/* NAND flash command */
>>> +#define CONFIG_CMD_NAND
>>> +#define CONFIG_CMD_NAND_TRIMFFS
>>> +
>>> +/* NAND stuff */
>>> +#define CONFIG_NAND_MXS
>>> +#define CONFIG_SYS_MAX_NAND_DEVICE 1
>>> +#define CONFIG_SYS_NAND_BASE 0x40000000
>>> +#define CONFIG_SYS_NAND_5_ADDR_CYCLE
>>> +#define CONFIG_SYS_NAND_ONFI_DETECTION
>>> +
>>> +/* DMA stuff, needed for GPMI/MXS NAND support */
>>> +#define CONFIG_APBH_DMA
>>> +#define CONFIG_APBH_DMA_BURST
>>> +#define CONFIG_APBH_DMA_BURST8
>>> +
>>> +/* Network */
>>> +#define CONFIG_CMD_PING
>>> +#define CONFIG_CMD_DHCP
>>> +#define CONFIG_CMD_MII
>>> +#define CONFIG_CMD_NET
>>> +#define CONFIG_FEC_MXC
>>> +#define CONFIG_MII
>>> +
>>> +#define IMX_FEC_BASE ENET2_BASE_ADDR
>>> +#define CONFIG_FEC_MXC_PHYADDR 0x0
>>> +
>>> +#define CONFIG_FEC_XCV_TYPE RGMII
>>> +#define CONFIG_ETHPRIME "FEC"
>>> +
>>> +#define CONFIG_PHYLIB
>>> +#define CONFIG_PHY_ATHEROS
>>> +
>>> +
>>> +#define CONFIG_CMD_USB
>>> +#ifdef CONFIG_CMD_USB
>>> +#define CONFIG_USB_EHCI
>>> +#define CONFIG_USB_EHCI_MX6
>>> +#define CONFIG_USB_STORAGE
>>> +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
>>> +#define CONFIG_USB_HOST_ETHER
>>> +#define CONFIG_USB_ETHER_ASIX
>>> +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
>>> +#define CONFIG_MXC_USB_FLAGS 0
>>> +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
>>> +#endif
>>> +
>>> +#define CONFIG_DM
>>> +#define CONFIG_DM_THERMAL
>>> +#define CONFIG_SYS_MALLOC_F_LEN (1 << 10)
>>> +#define CONFIG_IMX6_THERMAL
>>> +
>>> +#define CONFIG_CMD_FUSE
>>> +#if defined(CONFIG_CMD_FUSE) || defined(CONFIG_IMX6_THERMAL)
>>> +#define CONFIG_MXC_OCOTP
>>> +#endif
>>> +
>>> +/* FLASH and environment organization */
>>> +#define CONFIG_SYS_NO_FLASH
>>> +
>>> +#define CONFIG_FSL_QSPI
>>> +
>>> +#ifdef CONFIG_FSL_QSPI
>>> +#define CONFIG_CMD_SF
>>> +#define CONFIG_SPI_FLASH
>>> +#define CONFIG_SPI_FLASH_SPANSION
>>> +#define CONFIG_SPI_FLASH_STMICRO
>>> +#define CONFIG_SYS_FSL_QSPI_LE
>>> +#define FSL_QSPI_FLASH_SIZE SZ_16M
>>> +#define FSL_QSPI_FLASH_NUM 2
>>> +#endif
>>> +
>>> +#define CONFIG_ENV_OFFSET (6 * SZ_64K)
>>> +#define CONFIG_ENV_SIZE SZ_8K
>>> +#define CONFIG_ENV_IS_IN_MMC
>>> +
>>> +#define CONFIG_OF_LIBFDT
>>> +#define CONFIG_CMD_BOOTZ
>>> +
>>> +#ifndef CONFIG_SYS_DCACHE_OFF
>>> +#define CONFIG_CMD_CACHE
>>> +#endif
>>> +
>>> +#define CONFIG_SYS_FSL_USDHC_NUM 2
>>> +#if defined(CONFIG_ENV_IS_IN_MMC)
>>> +#define CONFIG_SYS_MMC_ENV_DEV 0 /*USDHC3*/
>>> +#endif
>>> +
>>> +#define CONFIG_PCA953X
>>> +#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x30, 8}, {0x32, 8}, {0x34, 8} }
>>> +
>>> +#endif /* __CONFIG_H */
>>>
>> Best regards,
>> Stefano Babic
> Best regards,
> Ye Li
Regards,
Peng.
More information about the U-Boot
mailing list